Search Documents

By M. E. Kravetz, E. B. Milosavljevic, L. R. Solujic

Gold ores containing high levels of cyanide-leachable copper minerals, such as covellite, chalcocite, bornite, malachite, azurite, and cuprite have traditionally been difficult to treat economically. A novel hydrometallurgical process for efficient treatment of cyanidation effluents obtained by leaching high copper gold ores (or concentrates) based on the use of Cherokee Chemical organo-sulfur reagents (OSR-A, OSR-B and OSR-C) is described. The process may be modified to selectively precipitate silver, or completely recover silver, copper and zinc, as well as regenerate significant amounts of cyanide. For example, data obtained demonstrate that 100 % of silver and zinc, and 98 % of copper were removed from the solution, while 80 % of cyanide was recovered. The treated barren solutions exhibit enhanced gold and silver leaching kinetics compared to the untreated controls.

Jan 1, 2004

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36, and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

Feb 27, 2013

By Tim O’Neil

What prompted the merger of the two long-established American Mining Congress/National Coal Association (AMC/NCA) groups that combine the coal, hard-rock, industrial- and agricultural-minerals sectors of mining? Both associations have been facing similar stresses for several years - structural changes in their respective industries, the changing personality and role of government and well-financed and organized opposition groups. In 1993, the AMC board of directors undertook efforts at reorganizing the association. One board member, who serves on both boards, suggested it might be time to give serious consideration to merging the organizations. This is an idea that had been discussed more or less informally at least three times during my tenure at NCA. Negotiations toward a merger began after that and were consummated in February of this year.

Jan 1, 1995

By Max Friedemann, Franziska Günther, Helmut Mischo

Ensuring adequate ventilation is a critical aspect of safety in underground mining operations. In small-scale mines in particular, key ventilation parameters such as temperature, humidity, and air velocity are often measured manually and only at infrequent intervals, typically using analog instruments. As a result, real-time monitoring of environmental changes, timely detection of hazardous situations, and demand-driven ventilation control are not feasible. This presentation discusses the selection and evaluation of modern digital ventilation measurement devices, including handheld instruments with digital data logging capabilities and continuously operating sensors with potential for real-time data transmission. The investigations focus on the challenges posed by underground environments with extremely high humidity levels, which can adversely affect sensor performance and electronic components. The results are based on testing conducted at the Research and Teaching Mine of TU Bergakademie Freiberg—an underground ore mine characterized by humidity levels exceeding 95%. Findings include assessments of measurement accuracy, reliability, and practical applicability under these demanding conditions.

Feb 22, 2026

By P. Conrad

Experience has shown that, since the passage of the Surface Mining Control and Reclamation Act, over-compaction of spoil during the reclamation process has severely limited tree growth on reclaimed land. Researchers at the University of Kentucky have conducted a ten-year investigation at a surface mine in eastern Kentucky that monitored the changes in selected spoil physical characteristics for various reclamation and compaction alleviation methods. More specifically, research plots were developed for reforestation that employed three different levels of compaction and two different methods of ripping for overly compacted spoil. Each year measurements were made in the field of dry bulk density, using a nuclear density gage, and maximum penetration depth, using a recording cone penetrometer. In addition to good correlation between tree growth and selected spoil characteristics, the data demonstrated a gradual convergence of the measured spoil characteristic data over the study period.

Jan 1, 2008

By M. Javier

Mining, waste is growing problem both physical accumulation and increasing toxic uncertainties it presents in the long run. Its value ?zero? is strictly calculated by economy. This mining model begs the question: What is the value of waste & what does it represent to the mining industry? Waste is widely accepted as a ?by product? generated as a consequences of the mining process. The abundant waste accumulation affects society, as receptor, in many ways and the waste piles of materials has no use and no destiny. In reality, this waste is monument of imperfection of the extractive industries worldwide. Our planet is finite and has strict limitations, which mining has traditionally ignored. It is time to design a new system, in which clearly, waste design must be integrated in whole mining process; it has no room to postpone. This paper presents a concept in waste design by which toxic mining waste not only can be rendered inert but also act as nutrient to help balance the ecosystems. This concept calls for extractive industries to pursue EQUILIBRIUM with nature (Geomimic). Also, this concept offers countless gains and opportunities fro the industry and by converting liabilities into assets; mining engineers become the managers and stewards of nature. Also, waste design offers new solutions for proper and sustainable waste management of the mining industry.

Jan 1, 2011

By Steve Kral

Through advanced technology and innovative thinking, the mining industry has become one of the world’s leading industries in environmental protection. But it only takes one Summitville, Omai or, most recently, the Aurul gold tailings retreatment operation in Romania to provide ammunition to the industry’s critics in their attempts to sway public opinion against mining. So for the mining industry to continue operating with the public’s support, it must continue to improve its tailings waste-disposal processes and the dams that hold this waste. In January, about 120 specialists in the mine waste management field gathered together to discuss the available technologies and materials for controlling mine waste and mill tailings disposal. “Tailings and Mine Waste’00” was held at Colorado State University in Fort Collins, CO. This meeting, begun in 1978, is a continuing symposium. It provides a forum for environmental professionals to discuss the state-of-the-art in mill tailings and mine-waste disposal methods.

Jan 1, 2000

By K. T. Lee, M. U. Ozbay, M. D. G. Salamon

Design of yielding chain pillars in deep coal longwall mines is not as well established due mainly to the lack of knowledge in the behavior of coal pillars in the post-peak regime. This study shows that two of the existing strain-softening models have the potential to provide an improved understanding of yielding and, therefore, could form a rational basis for yielding coal pillar design. Analytic and numerical modelings of a row of chain pillars in a two-entry development at a depth of nearly 700 m suggests that yielding pillars are feasible, but the design is very sensitive to the coal’s post-peak behavior.

Jan 1, 2001

By Walter Hermülheim, Klaus-Dieter Beck

In German hardcoal mining approximately 1 or 2 cases of spontaneous combustion are recorded per 10 million tonnes of saleable output. In approximately every 20th spontaneous combustion case, CH, is ignited. By the example of a fire caused by spontaneous combustion on Friedrich Heinrich colliery, an overview on the measures taken for firefighting and explosion prevention is given. These measures comprise (in sequential order) - early fire detection by CO-monitoring, - gob-sealing measures against ventilation air leaks, - full-space inertization of the coalface subsequent to a CH,- deflagration, - installation of a target inertization of the caved-in gob under the protection of the full-space inertization, - re-opening of the fire zone and reestablishment of the ventilation-air current, - completion of the salvaging work with continued target inertization of the caved-in gob and further sealing measures (monolithic packing), - sealing of the coalface after salvaging. The measures described allowed gain of control of a safety- critical (because close to the face) gob fire caused by spontaneous combustion, in spite of a CH, deflagration, within few days only, and salvaging of equipment from that coalface and start-up of the follow-up coal-face on schedule. The measures taken as well as the experiences gained allow deduction of general safety criteria for fighiing of gobfires caused by spontaneous combustion, and for controlling the explosion risk. e.g. - warning and alert thresholds for early detection of fires, - criteria for spotting of the zone of fire, - rules for tightening caved-in gobs, - thresholds for the retreat of firefighting crews from the vicinity of the zone of fire, and for starting ineiization, - considerations for positioning of and strength requirements for stoppings with/without inertization, - flow-by-volume adjustment of inertization, - safety rules for work with respiratory apparatus in the inertized zone, - safety rules for the re-opening of zones of fire. The considerations end up in the conclusions that the duration in terms of months of the classic cycles of sealing, waiting, and reopening can nowadays be reduced to a few days only by purposeful combination of full-space inertization and locally confined tar- get inertization of the gob area. The earlier high risks incured by the mine resuce squads en- trusted with sealing of zones of mine fires under explosion hazards can be reduced by the method described, provided the safety regulations are conformed with. In this way, intertizing contributes substantially to reduction of down-time caused by mine fires, to preservation of recoverable parts of the deposit, and to improved safety of the fire-fighting crews.

Jan 1, 1997

By Charles Ronkos, Jeffrey Edwards, Brian Brodsky

The Marlin gold-silver deposit is in western Guatemala, 15 kilometers south of a major transform fault that separates the North American and Caribbean plates. A district-scale, northwest-trending graben controlled deposition of a greater than 1200 meter thick upper Tertiary quartz latite to rhyolite volcaniclastic sequence. These volcanics were subsequently intruded and unconformably overlain by a small intermediate, latite to andesite, volcanic complex. Classic low-sulfidation, quartz-calcite-adularia veins and stockwork formed a 2.2 million ounce gold deposit, in association with late-stage andesite dike swarms, along a west-northwest striking normal fault on the eastern flank of the volcanic complex.

Jan 1, 2005

By P. Harris, G. Groenmeyer, L. Parolis

The effect of molecular weight, charge and the presence of the cations Ca2+, Mg2+and K+ on the adsorption of carboxymethyl cellulose on pure talc obtained from Balmat, New York have been investigated. Higher adsorption densities were obtained in the presence ofCa2+ and Mg2+ ions than with K+ ions and higher ionic strength solutions resulted in higher adsorption densities. Changing the molecular weight did not influence the adsorption however increasing the charge (DS) of the polymers resulted in lower adsorption densities.

Jan 1, 2004

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, NV began large-scale production in 1977. During 2008 Round Mountain Gold Corp. (RMGC) relocated the primary crusher facility approximately 300 m (1,000 ft) to make room for the next phase of openpit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket. RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17-m- (56-ft-) high mechanically-stabilized embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, CO. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design and construction of the MSE wall.

Jan 1, 2010

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By Y. C. Kim, F. Szidarovszky

G.M. Philip and D.F. Watson The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write : "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accu¬mulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common. ? References Journel, A.G., 1986, "Geostatistics: models and tools for Earth Sciences," Journal of Mathematical Geology, Vol. 18, No. 1, pp. 119-139. Philip, G.M., and Watson, D.F., 1985a, "Theoretical aspects of grade-tonnage calculations," International Journal of Mining and Geological Engineering, Vol. 3, pp. 149-154. Philip, G.M., and Watson, D.F., 1985b, "A deterministic approach to computing ore reserves. I, Grade Estimation," Earth Resources Foundation, Occas. Paper 2, The University of Sydney, 24 pp. Philip, G.M., and Watson, D.F., 1987a, "Neighborhood discontinuities in bivariate interpolation of scattered observations," Mathematical Geology, Vol. 18, No. 1, pp. 69-74. Philip, G.M., and Watson, D.F., 1987b, "Estimating interactions of topological functions," Mathematical Geology, Vol. 18, (at press). Reply by Y. C. Kim Before replying to the comments by Philip and Watson, it is desirable to establish the original perspective of our paper, which was intended primarily for the practitioners of mining who possess a working knowledge of ordinary kriging. The paper tried to convey the following practical points: (1) there are circumstances in which one observes negative weights, (2) illustration of circumstances under which one can expect negative weights, (3) should one obtain a negative estimated grade, one can resort to elimination of negative weights using the technique outlined in the paper, and (4) one could normally select only the first layer of surrounding assays to estimate the block grade. Under such a perspective, most of the comments by Philip and Watson are irrelevant and misdirected. For example, the practitioners do not find it difficult to "interpret" the results of ordinary kriging, as evidenced by the fact that they have been using the results for nearly a decade. Nor are the practitioners concerned with discontinuities in estimated block grades due to changing neighborhood of assays during kriging. What matters to the practitioners is the fact that kriging does provide the best estimate among all the estimation tools available to them as of today. ?

Jan 2, 1987

By F. L. Pirkle, D. L. Pirkle, E. C. Pirkle, W. A. Pirkle

Heavy minerals have been mined from the sands of the United States’ Atlantic Coastal Plain since the early part of the twentieth century. Production of ilmenite from beach sands near Mineral City (Ponte Vedra), Florida, began in 1916. The first reported large-scale recovery of zircon in Florida was reported from this deposit in 1922 and of rutile in 1925. These operations ceased in 1929. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site. In 1942 heavy-mineral operations were established on 202 hectares of land situated in Duval County, Florida. The location is about 16 kilometers east of the center of Jacksonville, Florida, in an area known as Arlington. This operation demonstrated that low-grade sand containing only 2 to 3 percent titanium minerals could be concentrated economically with the Humphreys spiral and that the oxides could be separated from the heavy silicates by electrostatic methods. Much of this area is now covered by a large mall and is a major retail- commercial center. Between 1958 and 1964 the Skinner tract, a deposit about 4 kilometers south of the above deposit, was mined. Today the area of this deposit is known as Deerwood, a gated country club community on the southside of Jacksonville. Further inland, E.I. du Pont de Nemours and Co. has been mining heavy minerals from a physiographic feature known as Trail Ridge since 1948, and a deposit near Green Cove Springs, Florida has been in production since 1972. Since the start of heavy-mineral mining in the southeastern United States, nine heavy-mineral ore bodies either have been or are being exploited in Florida and Georgia. Other deposits either have been lost to mining or are yet to be mined. These deposits have different origins. Some formed along shorelines at the heights of marine transgressions while others formed on regressional beach ridge plains during periods of temporary stillstands or slight transgressions. These different origins are reflected in the chemical and physical characteristics of the deposits. Ilmenite in older, more western deposits has a higher TiO2 content than ilmenite in younger, more eastern deposits. TiO2 content does not very with north-south direction. Garnet and epidote are absent or rare in the older Trail Ridge deposits, but progressively become common in the younger Duval Upland, Crestal Pamlico, and Holocene deposits. Grain size is coarsest for Trail Ridge sediments and finest for sediments in Duval Upland and Crestal Pamlico deposits. The average grain size for Holocene deposits is intermediate between Trail Ridge and Duval Upland deposits. The two models for the origin of the heavy-mineral deposits – deposits formed at the height of major marine transgression; and deposits formed during periods of temporary stillstands or slight transgressions that occur during a general marine regression; - are consistent with known sedimentological data and depositional trends.

Jan 1, 2005

This geometallurgical study examines the gangue mineral variability at the Bingham Canyon porphyry copper mine in Utah. Understanding an orebody?s mineralogy is important for mine and mill planning because it provides information on the size, texture, and distribution of ore minerals, the relationship between ore and gangue minerals, and the extent and type of alteration. Quantification of the mineralogical variability and properties of an orebody provides valuable input to the ore model and may have a significant effect on recovery optimization. This study was designed to be carried out on an initially detailed scale in order to develop a robust methodology for measuring and quantifying specific parameters, such as the distribution of mineral phases, alteration assemblages and fractures from key ore domains at the Bingham Canyon mine (Figure 1). Details of the methodology are reported below. This technique can be applied to testing the impact of mineralogy on a number of processing parameters. [ ] Figure 1. Ore domain map of Bingham Canyon (Kennecott Utah Copper, 2003) showing the 33 geometallurgical ore domains. The samples for this study were collected from the northwest part of the deposit circled on the map. PROJECT BACKGROUND Geology The Bingham Canyon deposit is a large porphyry Cu-Mo-Au deposit with associated skarn and base-metal replacement deposits mined in an open-pit mine measuring about 2.5 miles across and 4,000 feet deep. The deposit is hosted by the Bingham Stock, a Late Eocene to Mid-Oligocene intrusive complex. The skarn is hosted by the Late Carboniferous-age Bingham Mine Formation, which is comprised of quartzites and basal limestones (Babcock Jr. et al., 1998). The Bingham Stock is a composite intrusive complex that was emplaced over a period of about two million years. The oldest phase is described as a fine-grained equigranular monzonite (MZ), which intruded the country rocks at 39.8 ± 0.4 Ma (U-Pb zircon TIMS age) (Parry et al., 2001). Subsequently, the quartz monzonite porphyry (QMP) was emplaced, followed by intrusion of a latite porphyry (LP). The final intrusive phase, which forms narrow dikes that crosscut the Bingham Stock, is represented by a quartz latite porphyry (QLP), which is dated to 37.5 ± 0.4 Ma by 40Ar/39Ar dating of sanidine (Deino and Keith, 1998). Also present, are a minette dike in contact with a QLP dike (Waite et al., 1998; Deino and Keith, 1998), and a biotite porphyry (BP), a quartz latite porphyry breccia (QLPbx), and a pebble dike (Redmond, 2002). The copper orebody is centered above the Bingham Stock and forms an inverted cup shape with three high-grade copper zones extending to depth. Molybdenite mineralization occurs within and extends below the copper orebody, but is not correlated with copper mineralization. The main sulfide assemblage is chalcopyrite, bornite, molybdenite, and pyrite. Gold is locally intergrown with chalcopyrite and bornite (Babcock Jr. et al., 1998; Phillips et al., 1998). The surrounding country rocks host skarn deposits with three main ore types - garnet skarns, massive sulfides, and iron oxides. The garnet skarns contain chalcopyrite and pyrite with magnetite veins. In the massive sulfides chalcopyrite and pyrite occur either in banded sulfides or in unconsolidated microbreccias. The iron oxides contain disseminated chalcopyrite with minor chalcocite and bornite (Harrison and Reid, 1998). The deposit is overprinted by several stages of alteration. Potassic alteration is concentrated at the center of the deposit. It is surrounded and partially overlapped by a propylitic alteration zone. Both zones are overprinted by sericitic alteration. In the northern part of the deposit evidence for argillic alteration can be found (Bowman et al., 1987). Similarly, the skarn deposit was also overprinted by several stages of alteration: wollastonite, idocrase, and garnet in cherty limestones, and quartz and diopside forming in calcareous quartzites. Distally, diopside was replaced by talc, tremolite, dolomite, secondary calcite, and pyrite, and quartz and sulfide veinlets with biotite and actinolite selvages are present. Andradite garnet, diopside, quartz, magnetite, hematite, and copper sulfides were overprinted by wollastonite (Babcock Jr. et al., 1998). Because the monzonite, quartz monzonite porphyry, latite porphyry, and quartz latite porphyry host the bulk of the mineralization, our research is focused on these lithologic units. Geometallurgy On the basis of geological (lithology, alteration assemblages, fracture density, copper mineralization) and metallurgical properties, the deposit has been divided into 33 ore domains by mine geologists and metallurgists (Figure 1). In map view, these domains cross geologically defined boundaries (MZ, QMP etc.). These domains reflect regions of the deposit that have particular, mapable attributes or properties. They reflect a combination of geological and mineralogical characteristics that combine to impact processing. Alteration, for example, as shown by talc mineralization, is one such key feature. Hardness may reflect the absence of sericitic but presence of potassic alteration. Structural discontinuities such as faulting, fracturing, or development of void

Jan 1, 2009

By M. Akser, M. Tomas

Six Sigma is a methodology that uses a structured and disciplined approach to improve process performance (higher throughput, better recovery, lower cost, shorter cycle time, etc.). Specially trained people called “black belts” lead and manage Six Sigma projects. Black belts, with assistance from their team, ensure that projects follow the DMAIC (define, measure, analyze, implement and control) process phases. Timely completion of each project, with measurable deliverables, is key to Six Sigma’s significant financial success. Implementation of Six Sigma has been growing in recent years in a wide range of industries. The heavy mineral industry, like many other industries, could benefit from what Six Sigma has to offer. Specific Six Sigma project examples are included from DuPont’s Heavy Mineral Production Plant in Florida.

Jan 1, 2005