Search Documents

By P. Marinos, G. Tsiambaos, H. Saroglou

The anisotropic behaviour of “Athens Schist” has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the “Athens Schist” were statistically analysed and evaluated. Le comportement anisotropique des roches du système “Schistes d’ Athènes” a été déterminé sur des épreuves avec une orientation différente de la schistosité par rapport à l’axe de chargement sous des conditions axiales, triaxiales et dynamiques. Un grand nombre des résultats a été statistiquement analysé et discuté. Zur Bestimmung der anisotropen Eigenschaften der Athen Schiefer wurden einaxialen, dreiaxialen und dynamischen Kompressionsversuchen an Gesteinskernen durchgeführt, bei denen die Belastungsachse verschiedenen Neigungen gegen die Schieferung hat. Die Messreihen an anisotropen unzerreissbaren Fels Samplen von Athen Schiefer wurden statistisch analysiert.

Jan 1, 2003

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By A. Meek

This report compares the compressed air driven rocker shovel to the newly developed Warthog Non-throw development end loader. The two machines were compared on aspects such as safety, loading potential, energy efficiency and costs. The objectives of the comparison were to determine whether or not the replacement of the rocker shovel with the Warthog will be operationally and financially justifiable. The results from this study were obtained from underground observations and time studies on the machines, as well as consultations and data collection at the shaft and suppliers. This paper compares only the Warthog loader to the Trident 215 rocker shovel used at Anglo Platinum?s Brakspruit shaft and does not compare the other models of rocker shovels, which are fundamentally the same but will have different loading potentials and specifications. Cleaning times for the rocker shovel are based on underground observations at Brakspruit shaft. These times can be influenced by factors such as blasting practices, compressed air pressure and operator experience and skill. For this reason the times will most likely vary at different shafts. The Warthog cleaning times are based on manufacturer specifications and results from trial stages and therefore further work is required to confirm cleaning times achieved.

Jan 1, 2009

By E. T. Boshoff

Paper written on project work carried out in partial fulfilment of B. Eng. (Metallurgical Engineering) The weathering of kimberlite can be accelerated with cations in solution if swelling of the kimberlite occurs in contact with the weathering medium. The type and amount of swelling clays present, along with the surface charge and cation valence, determine the degree of swelling that can occur. Crystalline swelling occurs by the incorporation of cations in the interlayer spacing of the silica sheets. Kimberlite exposed to cupric cations showed very strong weathering, indicating that this type of weathering may be considered a viable process option. Kimberlite fines generated after weathering with monovalent cations showed poor settling behaviour compared to kimberlite weathered with di-, and trivalent cations.

Jan 1, 2005

By M. F. Dlamini

The hydrodynamics of a hydrocyclone present a complex internal flow structure, the numerical simulation of which remains a non-trivial task. We report on three-dimensional water-only computational fluid dynamics (CFD) hydrocyclone flow field predictions and highlight some of the issues concerned with the development of a CFD model incorporating an air core. The potential for the application of CFD as a hydrocyclone design tool is also discussed. Physically realistic velocity profile predictions were obtained, which challenge the classical account of the hydrocyclone radial particle classification mechanism. A pressure field distribution consistent with literature reports was also predicted. Keywords: hydrocyclone, computational fluid dynamics (CFD),classification mechanism

Jan 1, 2005

By M. D. Lionnet

The Bafokeng Rasimone Platinum Mine (BRPM) is a joint venture between Rustenburg Platinum Mines Limited and Royal Bafokeng Resources (Pty) Ltd (Bafokeng). The mining lease has been granted over Boschkoppie 104JQ and is located approximately 10 km south of the Pilanesberg Alkaline Complex. The Merensky Reef, which constitutes the principal orebody, is geologically complex. A relationship between its geological variability and the associated mineralization has been established by defining a number of facies types. The Merensky Reef has been subdivided into seven distinct facies types: the pegmatoidal facies, contact facies, FW1 potholefacies, FW3 pothole facies, FW6 pothole facies, and FW7 pothole facies. The Merensky Reef, which does not form part of the potholed reef, has a large component of footwall mineralization. The pothole facies, in contrast, has mineralization located in the hangingwall. Statistical analysis of the facies types indicates that they are unique populations and hence need to be evaluated independently. The mining lease has distinct structural domains that have added additional complications to evaluation of the Merensky Reef. The Merensky facies on BRPM exhibit unique geological and statistical characteristics within well-defined structural blocks. Due to the extreme variability of the Merensky Reef on BRPM a unique approach has been developed, within Anglo Platinum, to evaluate the deposit. Mining cuts are defined and composited for the individual facies types, and then modelled individually by applying known geological controls. The resultant grade models are weighted based on statistical and local geological knowledge. The object of weighting the facies is to replicate the variability observed in the orebody. The introduction of stringent geological controls to the evaluation process has resulted in increased confidence in the in situ grades estimated as an input to the mine planning process.

Jan 1, 2007

By GA Harrison

The introduction of Extra Low Profile (XLP) mechanised equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations to achieve injury free sustainable production and cost effective mining technologies. The method allows for the introduction of a suite of XLP and Low Profile (LP) equipment in a narrow reef (1,2m) mining environment. For the first time it is now possible to achieve total trackless mechanisation at these stoping widths and XLP Breast mining has the potential to add more value when benchmarked with conventional mining and other mechanised methods. Various types of XLP equipment were tested at different sites within Anglo Platinum and this paper describes the XLP equipment evolution to-date. It concludes with recommendations on our future strategy regarding implementation and roll out of the XLP technology within Anglo Platinum.

Jan 1, 2008

By F. H. Abd EL-Rahiem

A selective dispersion process is presented and the work carried out to find optimum process conditions to minimise the colouring material in ground calcium carbonate (GCC) is described. The feed material is the overflow product from a hydrocyclone which results from using a Denver Attritioning machine with semi-autogenous grinding for one hour and a 1:1 ore/water ratio. By using sodium silicate (SS), with pH 9 and pulp density 5%, the iron content (as colouring impurities) is decreased from 0.21% in the original concentrate to 0.12% in the final concentrate. The degree of whiteness reached is improved to 85% from 63% in the original material. However, by using hexametaphosphate (SHMP) at pH 10 at the same pulp density, the iron content decreased to about 0.073% and hence the whiteness degree increased to about 96%.

Jan 1, 2004

By H. Zhu

Coal desulphurization by flotation is often difficult due to the surface oxidation of coal pyrite. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were adopted to obtain detailed information about the surface oxidation of pyrite. Fresh pyrite surfaces were found to be hydrophilic, and to turn hydrophobic after initial oxidation, with oxidized products such as polysulphide FeSx and free sulphur. The oxidized products on the pyrite surface were reduced by an electrochemical method, returning the surfaces to a hydrophilic state and thus increasing the separating efficiency of coal from pyrite by flotation. Key words: surface oxidation, pyrite, SEM, XRD pattern, electrochemical modification.

Jan 1, 2002

By R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key aspect of mechanization is the optimization of equipment utilization, and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2007

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

By F. T. Cawood

The definition of mineral rents has historically been somewhat unclear, but a growing understanding of the source and composition of the revenues that comprise these rents mean that they can be more easily identified and quantified. Furthermore the way in which the flow of the rents from mineral developments are captured and then distributed has been a point of contention amongst the various stakeholders. Investors, the host government, the resource owners, environmental interests, indigenous groups and land owners are identified in this paper as the principal participants in mineral development and while each is entitled to a portion of the rent, the size of their portions will differ. A competitive rent-sharing model for southern African countries has been established and indicates how the range of stakeholders could be rewarded for their contribution. Acceptance of the sharing ratios amongst the recipients is a function of their understanding of the size of the rent and their position in the hierarchy of stakeholders. At first glance investors appear to receive the largest share of the rent, but they disburse some of the rent to hidden costs, which when all is said and done, means that investors and host governments retain approximately equal shares of the mineral rent. Both the investor and government are faced with the dilemma of how to equitably distribute the rents they have captured to minority stakeholders. Government captures corporate tax, mineral royalties and a wide range of subordinate taxes, but is required to construct policies that will ensure distributional equity among the various levels of government as well as among the provinces that comprise the country. Investors will have to ensure that a portion of the rents they capture are diverted to other stakeholders namely resource owners, environmental interests, indigenous peoples groups and the landowners. This paper identifies the major recipients of rent and provides some indication of equitable distribution ratios for mineral wealth among them?a first step in ensuring that mineral development is compatible with long-term sustainable development and in the best national interests.

Jan 1, 2002

By J. N. Van der Merwe

The current state of the South African mining industry is briefly reviewed from the point of view of an engineer not schooled in the finer details of predictive economics. Based on the assumption that current world exploration targets are indicative of which commodities the world will want in the future, it is concluded that the South African mining industry will continue to be viable and growing well into the future. South Africa holds the minerals the world wants and needs, and as long as the world has people, the demand for those, including gold, will continue to grow. There still is a growing demand for vanity commodities' and even the demand for platinum as a jewellery material displays significant growth. Mine safety still needs to improve, but significant improvement has already been made although the industry is not always acknowledged for the effort in this field. The safety target set for 2013 is within reach but will require sustained effort. The physical mining conditions for the main revenue earners, coal, platinum, and gold, will change substantially in the near future. Research in mining has declined alarmingly and it is urgently necessary for that to be revitalized to generate the knowledge that will be required. In order to streamline the transfer of knowledge to the mining engineers of the future, research needs to be conducted with the full involvement of the universities. It will also be necessary for the universities to continually review curricula to incorporate the latest knowledge and to embark on a campaign of knowledge transfer to the older generation of mining engineers. The mining industry is well supported by the universities, who have done their duty with regard to societal transformation, and the universities are in turn supported by the industry through vehicles like the METE Industry is also strongly supported by a number of professional and vocational societies. The SAIMM will continue to play its vital role as the meeting point of the mining technical sciences, and will continue to disseminate knowledge via the journal, schools, and conferences. In the future, it will review its modus operandi to support the needs of growing membership in the remote branches. It will enter the research arena in an appropriate manner and give effect to the developing integration of mining and society. The most important threat to the future of the mining industry is the recurrent mention of nationalization. While interaction between the mining industry and political and economic development of South Africa has always been characteristic, the current debate is emotional more than rational, and engineers are not well equipped to participate. This matter needs to be finalized before it becomes a popular force that politicians cannot control.

Jan 1, 2011

By A. D. Pelton, Y. -B. Kang, S. A. Decterov

Computerized thermodynamic databases for solid and liquid metal, slag and solid oxide phases in the Al2O3-CaO-CoO-CrO-Cr2O3-FeO-Fe2O3-MgO-MnO-NiO-SiO2-S system have been developed by critical evaluation/optimization of all available phase equilibrium and thermodynamic data. The databases contain parameters of models specifically developed for molten slags, liquid steel and solid oxide solutions such as spinels, pyroxenes, olivine, monoxide (wustite, periclase, lime), corundum, etc. By means of the optimization process, model parameters are found which reproduce all thermodynamic and phase equilibrium data within experimental error limits. Furthermore, the models permit extrapolation into regions of temperature and composition where data are not available. The databases are automatically accessed by user-friendly software that calculates complex equilibria involving simultaneously slag, metal, refractories and gases, for systems with many components, over wide ranges of temperature, oxygen potential and pressure. A short review of the available databases is presented. The critical evaluation/optimization procedure is outlined using the Al2O3-CaO-FeO-Fe2O3-SiO2and Al2O3-CaO-MnO-SiO2systemsas examples. Several applications of the databases to deoxidation of iron and to inclusion control in steel are discussed. Keywords: thermodynamics, phase equilibrium, phase diagrams, databases, ferrous metallurgy, steelmaking, inclusion control, slags, oxide systems.

Jan 1, 2004

By N. Ogbonna

A mathematical model for bioleaching at the agglomerate scale is developed. The agglomerate is defined as a unit volume of a heap which contains a solid phase (a size distribution of ore particles), a liquid phase (stagnant and flowing leaching solution) and a gas phase (flowing air and air pockets). Leaching at the level of an ore particle is modelled using a diffusion-reaction equation, and oxidation by attached and detached microbes is treated separately. With the aid of the mathematical model, the effect of particle size distribution on the bioleaching of an ore containing a mixture of chalcocite and pyrite, and a culture of iron oxidizers, is investigated.

Jan 1, 2006

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By R. M. Whyte

The Konkola Deep Mining Project (KDMP) seeks to exploit the deep level potential of the Konkola Deeps orebody, producing high grade copper concentrates for treatment at the Nkana Smelter and Refinery. As an alternative to smelting, Konkola Copper Mines (KCM) has examined a processing route involving pressure leaching of the Konkola concentrates at Nchanga, with the leach liquor being treated by solvent extraction and electrowinning to produce high purity copper cathode. The solvent extraction circuit would be operated to achieve a high ?delta? copper, thereby providing a strong acid raffinate which can be used in the existing Tailings Leach Plant (TLP) to treat Nchanga oxide copper materials. The main focus of the hydrometallurgical option is to capitalize upon the synergy that exists between the treatment of sulphide copper concentrates (acid producing) and oxide copper ores (acid consuming). The paper discusses the key features of a comprehensive piloting campaign carried out at Anglo American Research Laboratories, which involved the co-treatment of Konkola copper concentrates and Chingola refractory ore in a fully integrated pilot plant circuit.

Jan 1, 2001

By D. Pohl

The past decade has seen rapid expansion in the West African mineral exploration environment. This expansion has been largely driven by changes in ?Political climate ?Fiscal and legal regimes ?Exploration approaches ?West African geology. Major regional mapping and geochemical surveys by the UNDP, and the BRGM in the late 1970s and early 1980s laid the foundation for the rapid development of mineral exploration and resources during the past decade. An additional driving impetus was the discovery by native artisanal miners of many significant new gold occurrences at Libiri, Essakan, Bouda and Tirahori, during the great droughts of the late seventies and early eighties.

Jan 1, 1998