Search Documents

By Nareetsile S., J. Kabwe

In the past few years Orapa and Letlhakane Mines have investigated various new technologies to enhance and improve production. The goal has been to improve productivity, reduce operating costs and make the mines more profitable The advent of Global Positioning Systems (GPS) in the early ’80s brought about the realization of this concept. Orapa and Letlhakane Mines started using GPS in 1999 and it is now used atLetlhakane mine for surveying, vehicle tracking and dispatching and for floor control system. Orapa Mine uses GPS in surveying, floor control and drill navigation. It will also be used for vehicle tracking and dispatching in mid-2001 following the installation of a fleet management and control system. The introduction of GPS at both Orapa and Letlhakane mines have improved productivity and reduced operating costs in the areas of drilling, topographic survey and floor control. In vehicle tracking and dispatching GPS has allowed for real-time information management for timeous decision-making which optimized fleet run time hours.

Sep 1, 2001

By A. Hinde, M. H. Moys

Tailings from metallurgical plants, when deslimed with hydrocyclones, provide a valuable source of material for the backfilling of mines. The effectiveness of this material as a support medium is a sensitive function of its particle- size distribution and water content. It is therefore important that the hydrocyclone-classification plants used to prepare the backfill are operated efficiently, and that the effects of feed disturbances on the composition of the backfil are minimized. This paper addresses the problem of the design, control, and optimization of classification plants to satisfy this need. The development of a computer program to simulate the dynamic behaviour of a hydrocyclone circuit of any given configuration is described. The use of the simulator to investigate the relative performance of conventional and innovative control strategies for single-stage and two-stage circuits is discussed in depth. The results of simulation studies are presented that indicate there is considerable scope for improving the performance and cost-effectiveness of backfill-classification plants.

Jan 1, 1991

By A. Mitchell

On 25 August 2011, Andrew Mitchell, Lucas Moalusi, and Matthew van der Want of Bell Dewar hosted a presentation on Mining and Communities in Mooinooi, in the North-West Province. The conference was attended by traditional leaders in the North-West Province, officials from the Department of Local Government and Traditional Affairs, and executives from the mining industry. The presentation concerned traditional governance in mining, communities? rights in terms of applicable legislation, and the corporatization of community affairs.

Jan 1, 2012

By I. H. Clark

In some mining situations, backfills are not only required to be free-standing but are also expected to provide hangingwall support. It may therefore be specified that the backfill withstand a certain calculated stress within a given time. Given the materials available, the choice of backfill composition is not always straightforward, and an approach to the evaluation of cemented tailings backfill is therefore proposed. The general use of such a method will greatly assist in both the scientific analysis of the material properties for industry-wide purposes of comparison and decision-making as regards the choice of fill.

Jan 1, 1988

By C. J. Van Niekerk

When gold plant residues are cycloned for producing a coarse product for backfilling the gold and uranium values are upgraded in the backfill product. Gravity concentration, wet high intensity magnetic separation and froth flotation were investigated as first-stage recovery processes to recover these economic values from backfill prior to placement underground. This paper addresses the recovery of values from flotation concentrates and also details the economic feasibility of a treatment route including flotation, followed by roasting of flotation concentrate to liberate gold entrapped in pyrite and reverse gold leaching of the calcine so produced.

Jan 1, 1988

By R. C. M. van der Spuy

The heavy-minerals plant at the Palabora Mining Company treats 25 to 30 kt of new feed daily. The U3Og value of the ore averages approximately 40 p.p.m. The circuit consists of four stages of upgrading on 68 Reichert cones, fol. lowed by a jig and 30 table decks. The paper describes how feed-distribution problems have been overcome and the methods used for monitoring and controlling the cone performance. The adaptation of a standard jig for the recovery of fine minerals is discussed, and a method of 'table agglomeration, for the recovery of coarse refractory copper sulphide is described. The tables consist of polyurethane-covered fibreglass decks, and their operation is controlled according to measurements of the uranothorianite content of the concentrates and middlings by means of a nuclear scintillation counter. The upgrading ratio of the uranium mineral by gravity concentration is 1000:I, baddeleyite (ZrO.) being recovered as a by product.

Jan 1, 1982

By D. Ackerman, S. Cole, G. Langefeld, I. Parker

The removal of gravel from the seabed using a hydraulic mining tool is a complex multi-phase problem that cannot be analysed using traditional continuum based simulation techniques. One potential approach is to simulate the behaviours of the solid phase via the discrete element method and the liquid phase via finite volume based computational fluid dynamics. The interaction between the phases is accounted for by Eulerian coupling. The feasibility of using the combined computational fluid dynamics-discrete element method to simulate gravel entrainment from an idealized seabed is evaluated. The simulation results are validated using experimental data. It is concluded that while the current approach appears feasible, further work needs to be done to improve the accuracy of the simulation and to evaluate the approach?s ability to model more complex behaviours.

Jan 1, 2007

By J. C. Coetzee

In this article, a case is made for the importance of the transfer and management of tacit knowledge to ensure continued sustainable competitive advantage within the pyrometallurgical industry in South Africa. The state of knowledge management (KM) is assessed through a theoretical and empirical study. The empirical part of the study was conducted by means of a survey questionnaire. An important prerequisite within the research entailed determining the current state of KM within the pyrometallurgical industry, and the findings are presented throughout this article. The research argues for initiatives to address the high turnover of pyrometallurgical knowledge workers. This industry needs to entrench tacit knowledge and therefore address the problems associated with the continuous loss of inherent specialized knowledge. Appropriately, emphasis is placed on identifying initiatives required to embed and retain not only human capital lost through mobility, but rather retaining tacit knowledge through a practical KM framework.

Jan 1, 2012

In Chapter 1 we mentioned that up to three components are considered to represent the variability of regionalized variables : a deterministic component, a correlated component, and a random component. In Chapter 2 we considered some of the models based on the assumption of randomly distributed values: the random component was assumed to be the only one present. In Chapters 3 to 11, more general but also more complex models were described, based on the assumption that the values were correlated with the possible presence of random noise. In this chapter we introduce a model used to analyse non- stationary data, for which a deterministic component (or drift) must be assumed. This model will be used for estimation purposes, and the corresponding optimal linear estimation procedure is known as universal kriging. The theory of universal kriging is much more complex than the theory of kriging. Fortunately, in the majority of mine valuation problems the drift can be ignored and the simpler form of kriging can be used.

Jan 1, 1978

By S. Maluadzi, D. Rocchi, S. Luyckx, S. S. Potgieter-Vermaak, C. Machio, J. H. Potgieter

The aim of this work was to compare the corrosion behaviour of thermal spray WC ? based coatings before and after annealing. X-ray diffraction (XRD) was used to determine the phases present in the coatings at various stages. The corrosion resistance of the coatings was measured using electrochemical and immersion corrosion tests. The results obtained from electrochemical corrosion (quantified by corrosion current density) and immersion corrosion tests showed that annealing appears to decrease the corrosion resistance of the coatings. From the XRD results it was determined that the phases that corroded preferentially were cobalt (Co), eta (Co6W6C) and W2C. Keywords: Corrosion, thermal spray, coatings, hardmetals.

Jan 1, 2006

By R. O. Heckroodt

After a brief review of the characteristics of clay minerals and their origin, a summary is given of the industrial uses of different types of clay materials. The mining and beneficiation of clays are discussed, with special reference to the upgrading of certain types of materials. The occurrence and resources of the more important varieties of clays are dealt with in some detail, viz residual kaolin derived from granite and sediments, brickmaking clays, refractory clays, bentonite, and palygorskite. The Republic of South Africa is well endowed with a wide spectrum of clay materials, with one important exception. Kaolin suitable for paper coating is not known to occur in the Republic, and efforts to beneficiate and treat local materials to achieve the desired properties have so far been unsuccessful.

Jan 1, 1991

By D. Limpitlaw

As coal mining often results in the generation of acid mine drainage (AMD), careful planning and management of the water on such mines is required. A colliery in Mpumalanga recently sponsored independent research into the pollution-ameliorating potential of a natural wetland that has been receiving AMD for at least two decades. Samples of the sediment collected in the wetland were subjected to nine stages of sequential extraction in a determination of the distribution of the metal species present. The samples were then analysed for aluminium, iron, and manganese. The concentrations of sulphate-reducing bacteria (SRB) were also determined. The SRB concentration was found to increase with distance downstream (away from the source of pollution). An analysis of the sediment speciation data indicated that metal immobilization may be optimal in areas where the organic adsorption of metals is at its greatest. The analysis also provided evidence of the biogeochemical improvement of the water quality as the AMD passed through the wetland environment. The metal species present did not correlate strongly with the SRB populations; nor did the soluble species correlate with the species formed over long periods of time.

Jan 1, 1996

By M. L. Smith

A new approach to strategic planning, the Life of Business Optimisation System (LOBOS) optimises production systems from the scale of stopes in a single mine to an entire business strategy consisting of multiple mines and products competing for capital and processing capacity. LOBOS has optimised cash flow for a wide variety of operations, including large metalliferous or coal mines and as an aid to high-level strategic business optimisation solution to multi-mine/processing/product complexes. This paper discusses the application of optimisation technology to strategic planning with an emphasis on project evaluation with examples on the application of LOBOS to a variety of recent projects.

Jan 1, 2007

By S. K. Lahiri, K. C. Ghanta

Design of industrial slurry pipelines is usually performed by applying semi-empirical procedures, requiring a significant experimental study for each project. The mechanisms of suspension flow are not yet completely understood and existing predictive models cover only some aspects of uniform or closely graded particle slurry flows. This paper presents a computational technique for prediction of the velocity and concentration profile in slurry pipelines based on computational fluid dynamics. This model gives numerical solutions for the concentration and velocity distributions in the pipeline cross-section. The model prediction and experimental concentration and velocity profiles were found to be in good agreement. Keywords: pressure drop; concentration profile; particle diffusivity; slurry flow.

Jan 1, 2007

By J. D. Salter

Most diamonds are liberated from their ores by crushing. Diamond and other coarse grained mineral ores require carefully optimised crushing circuits. Recent advances in computer technology have made possible the on-line capture of crushing plant performance data and, hence, the accurate empirical modelling of the crushing process. Such models are used in simulation studies to determine the optimum operating conditions for a given plant. A system is described which allows operating data from mineral treatment processes to be logged. Up to 16 channels of data may be recorded simultaneously at sampling rates in the kiloHertz range per channel. A data storage and analysis procedure is described which allows the system to make full use of its sampling capabilities.

Jan 1, 1987

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.

By M. Thurston

This case study shows that for a set of lognormal data with a low coefficient of variation the semi-variogram of the logs has almost the same shape as the semi-variogram of the raw data. This means that the variogram of the logs, which is numerically more stable, can be used to krige the raw data. This technique is tested on samples from a sedimentary gold deposit and the results compared to those obtained from ordinary and simple lognormal kriging.

Jan 1, 1987

By A. García-Gutiérrez, A. Aragón-Jerónimo, R. Salazar-Mendoza

A theoretical analysis of a two-region solid-liquid flow system in horizontal pipes is presented, which considers a stationary bed of drill cuttings as a porous medium (-region) below of a two-phase dispersed flow (-region).The method of volume averaging was applied in this study to derive a rigorous mathematical model in which each variable is precisely defined. This model includes the volume-averaged transport equations for both the two-phase dispersed flow and the porous medium regions and terms from a macroscopic forces balance. The solution of the two-region model allowed evaluation of the behaviour of pressure gradient as a function of velocity, total volume fraction of cuttings and the relationship of the height of the stationary bed and pipe diameter. The solution is based on a backward finite difference explicit scheme. The simulated physical system is a pipe of 4.135 m in horizontal length and 0.0508 m in diameter. A one-dimensional, mesh-centred grid, consisting of 100 nodes, is used. The numerical results were compared with experimental data on slurry flows and a good agreement was found. Keywords: two-phase, cuttings transport, solid-liquid flow, drilling modelling, volume averaging.

Jan 1, 2007

By D. J. Hallbom

A new graphical method termed the ?Design Curve Diagram? (DCD) has been developed to analyse non-Newtonian pipe flow data by relating the plastic Karman number to the plastic Reynolds number. Since the plastic Karman number is directly proportional to the pressure loss gradient and the plastic Reynolds number is directly proportional to the velocity, the DCD is essentially a non-dimensional pipe flow curve. This makes the DCD conceptually easier than the commonly used Hedström-Moody diagram. While, the DCD was developed for the analysis of yield plastic fluids (e.g., Bingham plastics), it is equally applicable to Newtonian fluids.

Jan 1, 2007