Search Documents

By D. E. Scheck

A computer-aided blast design consultant system has been developed. The software consists of two modules: one uses theoretical and empirical formulae and procedures to design a blast based on user supplied geological and mechanical data, while the other is an expert system that analyzes blast vibration problems and recommends remedial action using knowledge based rules. The system is currently undergoing field evaluation.

Jan 1, 1987

By J. Baklík, V. Rak, W. Kolarcík, Z. Franc

The paper deals with hydraulic transport of thin and dense slurries. Based on mathematical modelling of three-phase flow, dynamic properties of the systems for pumping of thin slurry are solved. Theoretical calculations were experimentally verified both at the testing hall and in real operation. For thin slurry (e.g. bauxite slurry), a three-chamber hydrohoist with float is used. Dense slurry (e.g. ash and water) is transported from the power plant to a deposit site by means of a three-chamber hydrohoist with sealed separator (piston).

Jan 1, 2007

By G. G. Stanley

Mechanisms in the autogenous mill and their mathematical representation by G. G. STANLEY, B.Sc. (Eng.) (Wits.), M.E. (Queensland), Ph.D., (Fellow) The special characteristics of the autogenous mill are stated, and a suitable type of model for the mill is presented. Details of the test plant and experimental techniques for obtaining the data for model development are next given. followed by a discussion of the methods developed for the computation of the model parameters, namely the appearance matrix, the abrasion and crushing breakage-rate functions, and the discharge-rate function. Examples of results obtained with the model are given, and finally there is a brief account of confirmatory work on a fullscale autogeneous mill.

Jan 11, 1974

By L. Cornish, P. A. Olubambi, J. H. Potgieter

Four 22%Cr series duplex stainless steels alloys containing varying nickel contents of approximately 5, 7, 9 and 13% were melted in a vacuum induction furnace, hot rolled, solution annealed and water quenched. Their corrosion behaviour was investigated in sulphuric acid and sodium chloride solutions using a potentiodynamic polarization technique. Increasing nickel contents have appreciable influence on their corrosion behaviour. Polarization curves show similarities in the uniform corrosion behaviour of the alloys in the solutions and a significant difference in their pitting behaviour in chloride environments. Alloy 2209 generally exhibited highest resistance to uniform corrosion while 2213 displayed distinct and best pitting corrosion resistance. Their corrosion behaviour were attributed to the influence of nickel on phase modification, microstructural refinement, and the probably types of films formed in different environments. Keywords: Duplex stainless steel; Nickel; Microstructure; Phase modification; Corrosion

Jan 1, 2006

By H. W. Read, L. G. D. Napier

Change is endemic in our society. Future change will be accelerated by an explosion in technology, communication, and political thought. To meet these challenges, rapid structural changes have been taking place in mining organizations both here and abroad. The management of shaft-sinking projects is a case in point. Shaft sinking is a seminal element in the sustained well-being of a deep level mining venture. Its accomplishment is fraught with risk, involves a high level of capital expenditure, and is a precursor to profitable mining investment. The purpose of this paper is to present a concise and practical picture of the concepts, methods, and techniques of professional project management as applied to shaft-sinking projects.

Jan 1, 1994

By J. Trcková

This paper describes the method of modelling rock mechanical problems on experimental models. Based on an actual experiment used as an example, assessment of the surface deformation due to undermining, the extensive possibilities of using a 3-D physical model and application results in practice are demonstrated. A special method of modelling the underground mine progress by using paraffin melting is presented. Keywords: undermining, subsidence of surface, 3-D experimental model

Jan 1, 2009

By X. M. Prevost

A computer system to store, retrieve and process coal borehole and analytical data together with other geological, geographical or topographical information is described. As a result of the large volume and variety of data stored since its inception in 1979, as well as the basic versatility of the system, the National Coal Data Base has been performing a number of new tasks for which it was not originally designed. As considerable sets of data are used on almost every project, the use of statistical application programs has become an important processing tool.

Jan 1, 1987

By P. J. Petit

Financial evaluation is necessary to investigate the viability of implementing and/or utilising new technology in mining projects. It establishes a techno-economic base for decision-making and justifies capital expenditure. This paper aims to present a monetary appraisal of the electric rock drilling system in a typical feasibility project, whose purpose is to increase the production rate. The in situ environment is a platinum orebody, and the stoping operations occur in UG2 reef. The results are a function of production requirements, technical parameters and financial outlay of the drills. The costs involved in implementing and operating electric rock drills are assessed to the current method of drilling, namely the compressed air operation. A comparison of the electric and pneumatic rock drills in terms of financial outlays for drilling and service requirements, peripheral equipping and training is discussed. Other factors that affect the business case are technical advantages, safety and risk management and the environmental objective of the company.

Jan 1, 2006

By E. A. Brinkmann

A kinetic model framework for single particle kinetics in combined diffusion and adsorption processes is presented. The framework applies to the general case in which both diffusion and the adsorption reaction play important roles in determining the overall rate in processes where the migrating species can both adsorb and accumulate. The technique, which should be applicable to a wide range of reaction mechanisms, consists of an iterative integration procedure for the coupled diffusion and reaction equations. The case of a reversible linear adsorption reaction rate is developed. In order to verify the technique as a legitimate method of model development, an analytical solution for the identical case is derived and compared to the numerical solution. Excellent agreement exists between the two solutions.

Jan 1, 1987

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By P. T. Slatter

The role of viscometers for rheological characterization in the hydraulic transport of solids is discussed, and rheological models and phenomena pertinent to the hydraulic transport of backfill material are reviewed. The two main branches of viscometry (rotational and tube) for the measurement of mining slimes rheology are compared. The effects of solids concentration, particle size and chemical additives and the practical application of rheology in backfill system design are presented.

Jan 1, 1988

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analysts' inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted `floor' value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013

The optimal design of production phases and ultimate pit limit for an open pit mining operation may be generated using conventional or stochastic approaches. Unlike the conventional approach, the stochastic framework accounts for expected variability and uncertainty in metal content by considering a set of equally probable realizations (models) of the orebody. This paper evaluates the performance of a new stochastic network flow approach for the development of optimal phase design and ultimate pit limit using a gold deposit as the case study. The stochastic and conventional frameworks as considered here utilize the maximum flow and Lerchs-Grossman (LG) algorithms, respectively. The LG algorithm is restricted to considering an estimated (average-type) orebody model, while the stochastic maximum flow algorithm is developed to simultaneously use a set of simulated orebody realizations as an input. The case study demonstrates that, when compared to the conventional LG algorithm as used in the industry, the stochastic approach generates a 30 per cent increase in discounted cash flow, a 21 per cent larger ultimate pit limit, and about 7 per cent more metal, while it maintains a consistency in phase size.

Jan 1, 2012

While some of the practical details of ilmenite smelting are not well documented, there is a substantial body of literature on the principles of ilmenite smelting, and the behaviour of solidified titania slag. This information is summarized, focusing on the basic reactions, departure from equilibrium, the behaviour of impurities, and reactions of solidified slag. The emphasis is on the South African operations.

Jan 1, 2007

By P. Beukes, D. Bessinger, R. Glenewinkel

High titania slag is produced by the smelting of ilmenite and a suitable carbonaceous reductant in electric furnaces. Currently liquid slag is cast into large blocks, which take about 10 days to cool down before they can be crushed, milled and classified into two final products. The two products, chloride and sulphate grade slag, are differentiated according to their size. Granulation of titania slag has been identified as a possible alternative to the conventional block route. This paper discusses some of the work carried out at Exxaro Research and Development to investigate both wet and dry granulation of titania slag.

Jan 1, 2007

By R. Layton

Expert Systems Technology (EST) is becoming more and more widespread in both its range of applications and the public interest. It appears to be capable of performing tasks unmatched by other techniques. Within the mining industry a large body of unsolved problems now appear to have a solution. This paper examines the current state of EST both in the context of the history of Artificial Intelligence and current efforts at building mining expert systems. It provides recommendations for those wishing to get involved, and outlines the problems for those who believe that expert systems are capable of anything and everything. The paper also provides a detailed analysis of limitations of current EST that must direct research into more fundamental, commonsense areas than have been extensively covered before.

Jan 1, 1987

By Timo Niitti, Antti Rinne, Janne Turunen, Klaus Schommarz, Sami Grönstrand

This paper captures the essential steps employed in developing Outotec?s new FloatForceTM mechanism. The development of a flotation mechanism essentially revolves around the efficient transfer of installed power, or capital cost, to optimum flotation performance. Optimum flotation performance will be achieved if a balance between metallurgical results, operating and capital costs is maintained. The development of the FloatForceTM mechanism was done by careful evaluation of each of these three areas. This paper focuses on how experience, CFD and laboratory equipment, pilot and plant tests are used to test and evaluate a new flotation mechanism. Validated variables include mixing profile, power draw and local air hold-up. Metallurgical and mechanical design considerations are not covered in this paper. Besides using the FloatForceTM mechanism in new flotation equipment, the FloatForceTM mechanism can be used in existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented.

Jan 1, 2007