Search Documents

By E. J. Magri, A. Couble

Kriging estimates of geological resources are sometimes conditionally biased because the kriging plan contains too few samples. This may be done purposely in order to match the variance of the estimates to the true block dispersion variance. This work aims at evaluating the influence of conditional bias over the ultimate optimum pit design in relation to its shape, size and NPV (Net Present Value of profits). It has been restricted to two real case studies: a ‘carrot shaped’ gold porphyry in northern Greece and a manto-typeexotic copper deposit located in northern Chile. The methodology applied to each deposit consisted of generating a ‘real block model’ and four resource estimates by the use of conditional simulation and the application of four different kriging plans to the drillhole databases respectively. The estimation models vary in smoothness and conditional bias. Ultimate optimum pits were determined for the ‘real’ and the four different kriging models. Pit comparisons lead to the following conclusions: •In the worst case, conditional bias overestimated the project's NPV by 32% and 5% for the gold and copper deposits respectively. •The overestimation of high grades is more relevant than the underestimation of low grades. This resulted in a tonnage over-extraction of 148% and 1% for the gold and copper deposit respectively. This difference was attributable to the vastly different geometry of the deposits. •The smoothing effect of kriging, without or very little conditional bias, produced open pits that were different to the ‘true’ (ideal) ones and furthermore, underestimated the project's NPV by 10% and 6% for the gold and the copper deposits respectively. •Other factors that influence the optimum open pit design and to some extent control the effect of conditional bias are: the cut-off grade, the orebody geometry and distribution of grades within it and the amount of over-burden. Keywords: conditional bias, ultimate pit design

Jan 1, 2003

By P. S. Piper

In the 1960s it was suggested that the volume of stope convergence, and hence the rockburst hazard, could be reduced by the emplacement of backfill. Recent advances have facilitated the placement of large quantities of backfill underground, and a reassessment of its potential benefits as part of a regional support strategy is now timely. In this paper the principal criteria of effectiveness of backfill are taken to be its impact on face energy release rate (ERR) and average pillar stress (APS) levels, and maximization of acceptable ore extraction ratios. The possible effects of backfill on excess shear stresses (thought to modulate large seismic events) are also briefly reviewed. Analytic solutions describing backfill properties and their impact on ERR and APS in certain idealized geometries are also presented, and compared with the results of an extensive suite of computer simulations, in which parameter sensitivities are explored. Results indicate that a regional support strategy is required at depths exceeding 2 km in order to maintain acceptable levels of ERR, and backfill ribs can on their own fulfil this role at depths less than 3,3 km. At greater depths use of stabilizing pillars becomes imperative, but here too supplementary backfill ribs can reduce ERR and APS levels and permit significant increases in ore extraction ratios.

Jan 1, 1988

By A. Pytlik, W. Masny

"Underground mining is subject to various natural hazards such as seismic events, rockbursts, fire, and gas (methane). In general, an increase in the extraction depth causes an increase in the likelihood of these hazards, especially seismic activity and rockbursts. Dynamic phenomena such as rockbursts and tremors have been recorded on six continents: Europe (Poland, Russia, Czech Republic, Germany, and Slovenia), Asia (India, and China), North and South America (USA, Canada, and Chile), Africa (South Africa), and Australia. To select appropriate mine working supports for such dynamic phenomena, the performance characteristics of such support types must be determined under both static and dynamic load conditions.This article presents information regarding the application of rockbolts in Polish underground hard-coal mines. Dynamic phenomena occurring in the mines from 2004–2013 are also characterized. A methodology developed at the Central Mining Institute (GIG) for the laboratory testing of rockbolts is presented. In this methodology, the bolts are loaded by the direct impact of a free-moving mass (up to 20 000 kg) at speeds of up to 1.2 m/s. The facilities at GIG used to test the support under static and dynamic load conditions are characterized, and the results of laboratory tests on yielding bolts with a nominal capacity of 420 kN are presented. These types of bolts are commonly used for reinforcing steel arches and the surrounding rock mass in Polish coal mines. The results of the laboratory testing of yielding bolts are discussed.IntroductionSeismic events such as rock bumps and tremors occur with great frequency during underground mining. These phenomena have been reported in such countries as Poland, Czech Republic, Germany, France, Slovenia, Russia, India, China, the USA, Canada, Chile, South Africa, and Australia (Brauner, 1991; Potvin, Hudyma, and Jewell, 2000; Kidybin??ski, 2003; Driad-Lebeau et al., 2005; Li, Cai, and Cai, 2007; Whyatt and Loken, 2009; Durrheim and Riemer, 2012; Holub, Rušajova, and Holec?ko, 2011). Descriptions of the dynamic events and their effects in the form of damage to or destruction of supports have been presented in many publications, both for hardrock mines as well as for coal mines (Brauner, 1991; Dubin??ski and Konopko, 2000; Heal, 2010; Heal and Potvin, 2007; Simser, Joughin, and Ortlepp, 2002; Kaiser and Cai, 2012; Cai 2013; Nierobisz, 2013; Mark, 2014; Masny and Prusek, 2015). One of the main goals of the research has been to develop methods, criteria, and guidelines for the selection of an optimal and safe support for mine workings located in areas of rock bumps or tremors. Example of such studies include the Canadian Rockburst Support Handbook (Kaiser, McCreath, and Tannant, 1996), or the principles presented in the literature (Li, 2010; Cai, 2013)."

Jan 1, 2016

By Keith Rowley, Neal Harries, David Noon

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, South Africa, Zambia, Chile and the United States. Greater than 70 rock falls and waste dump failures (from several to millions of tonnes) have been monitored, and on every occasion precursor ?warning? movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines.

Jan 1, 2006

By G. Chunnett

Platinum metal prices have risen significantly during the past 18 months, and have remained at elevated levels. Driving these bullish prices are sustained jewellery demand, mainly from the Far Eastern markets, and ongoing autocatalyst usage in response to ever more demanding global environmental legislative requirements. Within South Africa, the areas north and south of the Steelpoort River in the Eastern Bushveldare well known for their significant resources of platinum. The bulk of the resources have lain dormant in anticipation of the very situation that is currently occurring in the marketplace. Anglo Platinum is the largest primary platinum producer in the country, and is uniquely positioned to take advantage of the current elevated metal prices and shortfall in supply of platiniferous metals. In addition to its production capabilities, Anglo Platinum holds an extensive portfolio of mineral reserves and resources which underpin its ability to implement expansion projects to continue growth in platinum group metal production. It also has access to, and is actively expediting, the exploration of a range of properties where the company can further expand current production capacity or supplemented depleted production levels.

Jan 1, 2006

By J. A. L. Napier

The evaluation of stress distributions and deformations in the vicinity of tabular mine layouts has been carried out routinely for many years using the displacement discontinuity boundary element method (DDM). In this approach, mine layouts are approximated as irregular shaped planar cracks (or slits) where the ?width? of the crack, corresponding to the excavation height, is assumed to be negligible compared to the in-plane, lateral dimensions. Early implementations of this approach have employed square element tessellations with constant displacement discontinuity component values. This is generally restrictive when considering the analysis of irregular pillar layouts or the intersection of fault planes with excavations. This paper describes a general revision of this approach in which triangular or quadrilateral element shapes are introduced in conjunction with higher order variations of the displacement discontinuity shape functions. This facilitates an accurate evaluation of detailed stress and displacement components close to excavation surfaces and allows the investigation of local damage and failure behaviour associated with particular geological structures such as weak parting bands or weak layers. A method to embed these features in an efficient and accurate multi-level solution scheme is described. This formulation can be extended to allow the analysis of shallow-depth pillar layout problems, facilitating the assessment of the interactive response and stability of shallow depth pillar layouts. A simple deformation model is introduced to facilitate the assessment of pillar failure and bursting potential in shallow mine layouts. The computational techniques described here have been implemented in a computer code called TEXAN (Tabular EXcavation ANalyser) and are illustrated by the simulation of a particular multiple reef pillar mining problem in a shallow depth platinum mine.

Jan 1, 2007

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

The peak in Sulphur price late 2008 caused again intensified investigation into the decomposition of sulphates and spend acid. One option is the recycling of sulphur from spend acid, which already started more than 40 years ago in the field of spend acid from organic processes in refineries and acrylic glass manufacturing. Since this acid couldn't be neutralized and discarded due to high organic contents, another source of SO2 to produce sulfuric acid is the decomposition of metal sulfates. The decomposition of metal sulfates was investigated at the next peak in Sulphur price in the 80?s. The first major scale pilot tests and studies of gypsum decomposition were carried out for clients in Florida. The decomposition of gypsum was quite often mainly influenced by the strategic decision of some countries to get own and independent acid production. In other cases the industry doesn?t have enough space to dump the gypsum. Therefore the company was also forced to convert the gypsum into ?saleable? products to avoid these residues. Other projects were made for the recycling of iron-sulfates from the pigment industry. The motivations for these projects were not only given by acid price. For the German pigment industry it was no longer permitted in the 80?s to dump the iron sulphate residues into the sea. These regulations forced the industry to develop new technology, which allows converting of the FeSO4-residues into iron oxide and acid. Therefore economical and mainly environmental factors influenced the decision of the companies to develop and to build these plants. Beside the above mention iron- and calcium-sulphates many other process exist, which produce metal sulphates as an intermediate product. These cases are not forced by environmental or strategic factors. In cases like Ni, Co or Mn-decomposition the main product of the plant is treated in the decomposition plant and later on used as ferrous-alloys. These final products are higher in price compared to e.g. CaO, which exclude the high-energy consumption for the endothermic chemical decomposition reaction. The reaction of SO2 generation based on acid or sulfate decomposition takes place in the range of 1000°C. The energy demand of the endothermic reaction is considerable and leads due to the high fuel-combustion off-gas stream to a diluted SO2 gas. Energy prices are usually increasing at the same time like sulphur. Sulphuric Acid based on decomposition is therefore more expensive than as acid based on sulphur combustion. The paper describes fluid bed technology and possible process concepts for decomposition plants. Additionally the thermodynamic background of the decomposition process and the main influence factors are provided to receive a better understanding of this technology.

Jan 1, 2009

By R. T. Tshikhudo

Nanotechnology can provide solutions to many of the world?s socio-economic challenges. The application of nanomaterials for water treatment and analysis, point-of-care diagnostics and targeted drug delivery systems or devices could improve the quality of life for people in developing countries. Gold colloids have a long history (dating back to the 4th century AD) and are particularly well known for their aesthetic appeal and their therapeutic properties. Since Faraday published a report on the synthesis and properties of colloidal gold in 1857, a reasonable insight into the nature of gold sols (nucleation, growth and kinetics of coagulation) has been developed. Considerable attention has been drawn during the past few decades to the development and optimization of methods for the preparation of gold nanoparticles. In nanoscience and nanotechnology today, gold nanomaterials appear to be the most widely used material by both academics and industrialists. This is due to the extraordinary properties of gold nanoparticles (e.g. optical, catalytic, and magnetic?they are also known to act as strong Raman enhancers and may also amplify fluorescence under certain circumstances). Mintek, through Project AuTEK and the DST/Mintek Nanotechnology Innovation Centre (NIC), has been at the forefront of the development of new industrial uses for gold. Mintek?s gold nanotechnology programme focuses on the development of gold-based nanostructured materials and their applications in health, water and other related areas. While few projects use gold nanoparticles for water treatment and analysis, Mintek?s gold nanoparticles are widely used in the health sector. For example, gold nanoparticles are engineered and produced in large quantities as systems for targeted drug delivery. They are also used as tools for advanced rapid diagnostic tests. Both optical and electrochemical rapid diagnostic methods are developed for the human and animal health sectors for point-of-care testing. This paper gives a brief introduction and overview of gold nanotechnology, and desrcibes the development of some of Mintek?s gold nanoparticle targeted drug delivery systems and lateral flow point of care prototype devices.

Jan 1, 2009

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006

By M. R. MacIver, M. Pawlik, H. Alizadeh

Treatment of tailings is an integral component of mineral processing. Tailings with a high clay content are a challenge for the mineral processing industry; e.g. the clay slimes produced from production of phosphate in the mid-western United States and the fine tailings produced from oil sands production in western Canada. Dispersants are a commonly used process aid, but their impact on the structure and settling properties of high clay content tailings is not well understood. The paper describes the changes in composition and bitumen release that occur when mature fine tailings (MFT) are treated with a polymeric dispersant (lignosulfonate.) Synchrotron-source computed tomography (CT) was used to obtain high-resolution 3D images of samples prepared at varying dosages of dispersant. The CT method permits a powerful visualisation of the internal structure and composition of the samples. These insights will enhance our understanding of the structural characteristics of mineral tailings relevant to solid-liquid separation by flocculation and thickening. Keywords: Dewatering, dispersion, dispersants, chemical treatment, computed tomography

Jan 1, 2020

By Allan Jansen, Robin Bissett

[Power-Point Presentation]

Jan 1, 2005

By A. J. Feltenstein

A theoretical model for prediction of dissolved gold loss from a rotary vacuum filter was developed as part of a program to implement optimizing control on gold plants The filter was modelled using a modification of the Hagen-Poiseuille equation and the Choudhury and Dahlstrom washing equation. The model has three parameters which must be determined from accumulated data before predictions can be made. These are the cake and cloth resistances and the filter washing efficiency. The model predicts with a fair degree of accuracy the response of the filter to changes in the independent variables and will therefore be a useful tool in the plant optimization study.

Jan 1, 1987

By John Taylor

?Introduction to Black Mountain ?Historical metal accounting practice ?Metal accounting audit ?Feed measurement ?Sample precision ?Concentrate measurment ?Current metal accounting practice ?Further refinements to the metal accounting practice

Jan 1, 2005

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By J H. Sullivan

Contents Background information Locality of Kumba?s Iron Ore Mines Sishen?s Product Specifications Geological Description of boreholes Sample Preperation Block delineations Production Geology Process Laboratory information Turnover times reached Inter Laboratory Comparisons Quality control activities in lab Purpose of laboratory Results attained Standard samples Monitoring of processes with QA/QC standards Mean paired difference of duplicates Duplicate samples Conclusion

Jan 1, 2005

By Milton Syamujulu

In 1994, Nkana smelter commissioned a Multimillion US$ Dollar Chilean Teniente converter (CT) in its operations in order to improve its smelting technological base. The main objective was to reduce the overall smelting energy costs and increase the sulfur capture for sulphuric acid production to support the company?s leaching operations at Nchanga Tailings Leach Plant. A decade of CT operations have since ensured following its installation and startup. This paper provides a Technical and Operational Audit of the performance of the CT in the first 10 years of its operations at Nkana smelter.

Jan 1, 2005

Nowadays, fully encapsulated rockbolts have become a key element in the design of ground control systems. The main reason is that they offer high axial resistance to bed separation. In this research, the load transfer capacity of a fully grouted bolt is evaluated analytically in an elastoplastic rock mass condition. The research considered the effect of bolt end-plate on load transfer capacity. Bolt and surrounding materials were assumed to be elastic and elastoplastic materials respectively. The load transfer mechanism of a fully grouted bolt is a function of parameters such as bolt length, shear stiffness of interfaces, in situ stress, presence of face-plate and distance along the bolt. These factors were analytically evaluated. Finally, the load along the bolt was predicted in different surrounding rock mass characteristics.

Jan 1, 2011

By J. T. Nel

The Kroll process is the traditional method of producing zirconium metal by reduction of zirconium tetrachloride with magnesium metal. This paper discusses the production of zirconium metal in a plasma reactor. Anhydrous low-hafnium ZrCl4 and Mg metal were fed continuously to a 30 kW non-transfer plasma reactor at a rate of 0.31 kg.h-1. Due to losses in the system the recovery of crude product was 77.5 %. After purification to remove unreacted feed material and MgCl2 by leaching, >98 % pure zirconium metal powder was obtained. The overall recovery of purified Zr was 74 %. The conversion efficiency of the process was 95 %.

Jan 1, 2012