Search Documents

By I. Ashmole

From the point of view of the environmental impact created, dimension stone mining is a relatively benign industry. There are no emissions besides those of the diesel powered earthmoving equipment utilised in its extraction and a small amount of blasting gases. Contamination of water resources is only likely in the event of petrochemical spillages from storage facilities and equipment, and these can largely be either prevented or cleaned up effectively. The major environmental impacts are of a visual nature, while in sensitive areas, habitat destruction and the destruction of archaeological heritage may become significant impacts. The dimension stone industry has grown at an average rate of over 7% per annum since 1986, and is forecast to continue growing at this rate for the foreseeable future. The cumulative environmental impact of the industry will thus become more significant over time. This paper discusses the environmental impacts of dimension stone mining and recommends effective means for dealing with the practical aspects of reclamation and mine closure in dimension stone mining within the context of environmentally responsible business practices. The discussion focuses mainly on the operations of the Finstone Group in Southern Africa, which are considered to be world leaders in the application of environmental management within the dimension stone mining industry, although reference is also made to other situations which the authors have encountered at dimension stone quarries around the world.

Jan 1, 2008

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By C. W. Siyasiya

Process and steel chemistry differences in hot rolled Al-killed low carbon strip steel between the hot charge route (HCR) as practised in a compact strip production (CSP) plant and the conventional cold charge route (CCR) have been studied. This was done with reference to differences in reheating practice, hot rolling practice and steel chemistry through emphasis on the effects of solubility and reprecipitation of AlN in the two process/product combinations and its effect on ferrite grain size development. An earlier modelling study on the evolution of the austenite grain size in both of the above hot rolling processes has also now been extended to include an estimate of the possible effects of retained strain after the last finishing pass on the ferrite grain size. As part of this study the equilibrium solubility trends of AlN in a number of boron-free low carbon Al-killed strip steels with low and high sulphur content from the two respective processes was investigated by the thermoelectric power (TEP) technique and differences in the effects through the derived solubility equation of Log[Al][N]=2.6?9710/T at typical slab reheating temperatures was demonstrated. Ferrite grain size modelling using the significantly lower Ar3 transformation temperatures generally found in hot rolled low carbon strip steel produced in the CSP plant using the HCR compared well to the larger grain size produced in the conventional CCR strip rolling plant. Keywords: austenite grain size modelling; thermoelectric power(TEP); compact strip production (CSP); cold charge route (CCR);ferrite grain size

Jan 1, 2008

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

By J. E. Quintanilha de Menezes, L. Ribeiro e Sousa, I. Ferreira

The Paradela dam has a spillway that makes it possible to discharge a maximum flow of 400 m3/s, the water discharges being on the river Sela, about 2km upstream the river Cávado. After the first use of the spillway, some landslides have occurred on the right bank of the river Sela as a result of the erosion generated on its base about one hundred meters near some houses of a small village. This paper presents a study performed for the slope stability where finite element results are taken into account. A monitoring program was established that essentially consisted of measuring sub-horizontal displacements in points located in boreholes at different depths and also phreatic levels. Some monitoring results are presented. Le barrage de Paradela a une décharge d’eau avec un débit maximal de 400 m3/s sur le fleuve Sela dans un endroit situé environ 2km sur l'amont du fleuve Cávado. Après la première utilisation de cette décharge, quelques glissements se sont vérifiés sur le versant droit du fleuve Sela résultant de l’érosion générée sur sa base dans une zone à 100 mètres de quelques maisons d’un petit village. Ce travail présente une étude réalisée concernant la stabilité du versant avec la considération des résultats des éléments finis. Un programme d’auscultation a été mis en place pour mesurer les déplacements sub-horizontales sur des points situés en forages à des différentes profondeurs. Quelques résultats de cette monitorization sont présentés. Der Ueberlauf des Padela Dammes ermoeglicht das Ablassen einer max. Wassermenge on 400 m3/s in den Sela Fluss, ca. 2 km flussaufwaerts des Cávado Flusses. Nach Inbetriebnahme des Ueberlaufes traten in ca. hundert Meter Entfernung zur Wohnbebauung eine Dorfes Erdrutschungen am rechten Ufer des Sela Flusses auf, die auf Erosionen am Flussbett zurückzuführen waren. In der vorliegenden Studie wurde die Boeschungsstabilitaet unter Beruecksichtigung von Berechnungsergebnissen der Finiten Element Methode untersucht. Es wurde ein essprogramm ausgearbeiten, das im Wesentlichen auf Messungen der Untergrundverformungen in verschiedenen Bohrlochteufen sowie auf Grundwassermessungen beruht. Im Folgenden sind einige Messergebnisse dargestellt.

Jan 1, 2003

By P. Hand

Most coal plants must run under conditions of varying feed conditions or are asked to produce qualities different from that used in the design. This can cause overloaded conditions as the ?bottlenecks? within the plant, depending on plant operation or as the feed changes. During plant design, geological information can be used to determine washability envelopes and blends that may be expected. Historical data can also be used to develop a size distribution envelope as well as to assign reasonable models for each of the unit processes. In operation, a plant can be sampled to determine changes and to refine process models. The information obtained can then be used in an accurate simulation to define how the plant can deal with the changing environment. This paper uses Limn: The Flowsheet Processor to simulate the coal plant in detail and will produce an accurate model, in terms of equipment sizing as well as water, medium, and solids balance, for each change in feed condition. It will show examples of running the simulation through complete density and size ranges and will determine the equipment required to address each part of the performance envelope.

Jan 1, 2010

By L. von Ketelhodt

Dual energy X-ray transmission (DE-XRT) sorting is a recent development in the range of sensor-based sorting technologies available today. DE-XRT is particularly suitable for dry coarse coal beneficiation in the size range -120 mm +12 mm. In this paper, we describe the technology and show the results of a number of test runs conducted on different types of coal from the USA and South Africa. The results have shown that DE-XRT is an effective technology not only for deshaling of coal and removing pyritic sulphur but also for separating coal and torbanite. The use of dry deshaling methods will be more important as water availability becomes a greater concern. DE-XRT is one such technology which will be incorporated in future dry coal processing plants.

Jan 1, 2010

By M. H. Moys

I had the good fortune to attend the above Conference which was held in Kanpur, India, on 11-15 December, 1995. The Conference was held in honour of Professor P.C. Kapur of the Indian Institute of Technology in Kanpur. Professor Kapur was one of the early students of legendary teacher and researcher of mineral beneficiation, Professor Doug Fuerstenau of the Department of Materials Science and Engineering at the University of California at Berkeley. I have attended my fair share of international conferences and this one certainly rated at the top of the list on several counts. With an open-hearted hospitality which one might almost take for granted once you have spent some time in India, the organizers of the Conference looked after every need of their guests, including breakfast and transport to and from the conference centre, wonderful traditional lunches and dinners and outstanding entertainment in the evenings. The papers were generally of a high standard, and debate flowed enthusiastically and freely. Several international guests delivered seminal papers in their fields as discussed below.

Jan 1, 1996

By W. Bendaikha, S. Larbi, A. Ramdane

An oolitic iron ore from Gara Djebilet, Algeria was characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectrosopy and the phosphorus distribution between various phases studied. Two ore types were identified – a haematite-dominated, oolitic type and a more massive, magnetite-dominated type. The haematite-dominated ore had a higher phosphorus content, up to 0.6% in the iron oxide minerals, than the magnetite-dominated type (0.3% P). Owing to the very fine-grained texture of the gangue minerals, reducing the phosphorus content to levels suitable for steelmaking (below 0.05% P) by conventiobal means would entail an energyintensive process with a high carbon footprint. Preliminary leaching test work using a sulphurous geothermal water as lixiviant, assisted by solar thermal acceleration, gave very promising results, removing 0.13% of the residual P (or 21.7% removal of total P) from the high-phosphorus oolitic ore.

Mar 14, 2024

By Z. Gxowa, L. H. Chown, U. Curle, G. Govender

This work evaluates the deformation behaviour, at warm working temperatures, of green particle-reinforced aluminium composites produced by powder blending in a high-energy ball mill. The work focuses on metal matrix composites (MMCs) based on the 2124-Al alloy, reinforced with 10 or 15 vol.% SiC and metal matrix nanocomposites (MMNCs) based on the 2124-Al alloy, reinforced with 5 or 10 vol.% Al2O3. Three batches for each powder were blended and powder properties such as particle size distribution (PSD) and shape were consistent after blending. It was observed that a more uniform distribution of the reinforcement phase in the aluminium alloy matrix was achieved in 2124-Al/Al2O3 than in 2124- Al/SiC composites. The powders (unreinforced 2124-Al and blended) were initially over-aged at 350°C for 2 hours to reverse any natural ageing that may have occurred prior to use. The over-ageing was incorporated to improve compressibility of the powders with the aim of achieving green compacts with higher integrity. Uniaxial compression tests performed at ambient temperature on a Gleeble® 3500 thermomechanical simulator were unsuccessful as the green compacts fragmented. Engineering stress-strain curves showed that green compacts of unreinforced 2124-Al, 10%SiC MMC and 5%Al2O3 MMNC deformed in a similar manner at ambient temperature and had the same compressive fracture stress of approximately 170 MPa. When the deformation temperature was increased from ambient to warm working temperatures (170–280°C) it was observed that electrical resistance heating (the heating mode of the Gleeble®) of unreinforced Al alloy, MMC and MMNC green compacts did not occur. This was attributed to the high electrical conductivity of aluminium, which resulted in poor heat generation due to the low electrical resistance in the samples. It was presumed that the small sample size (d=8 mm, h=12 mm) also caused rapid heat loss. After further experimentation, the green compacts were heated successfully by insulating the samples to retain heat. It was found that at 280°C, increasing the soaking time from 6 to 20 minutes decreased flow stress and improved plastic flow in the 2124-Al/10%SiC green compact.

Jan 1, 2016

Production caving started for Lift 2 at Northparkes in August 2004. In a period of less than 3 months, more than 10 000 seismic events were recorded. Events up to local magnitude +2.9 were induced near the mine during caving, with event rates of up to 500 per day. This paper documents the seismicity related to cave initiation and cave propagation during the initial production of Lift 2. The seismogenic zone of events initially moved at a rate of about 0.5 metres per day, accelerating to 2 to 3 metres per day after a few months of cave production. Seismic data analysis infers that the crown pillar between Lift 1 and Lift 2 was destressed over a vertical height of about 100 metres. As the seismogenic zone approached the crown pillar, a macroseismic episode occurred, with more than 20 events of at least local magnitude +1 occurring in a two-week period. Based on the seismicity recorded for Lift 2 at Northparkes Mines, a caving mechanics model is proposed. Comments and suggestions are made for seismic data analysis and design of seismic monitoring systems in block caving mines.

Jan 1, 2008

By A. E. Voigt

Iron ore samples representing the input and output of several jigging experiments were analysed to determine the effect of particle size, shape, and density on jigging performance. Traditionally, the manual measurement of the size and shape of individual particles is very tedious and prone to inaccuracies and inconsistencies. Using a novel multi-view imaging technique the 3-dimensional representations of each particle in the sample was determined. From this representation several size and shape measurements were extracted, and these were correlated with the individual particle density measurements. A rigorous investigation into the confidence associated with density and the size and shape features as a function of sample size was conducted, thus allowing the significance of correlations in the data to be determined. The jig?s performance was seen to be clearly sensitive to density and markedly so to particle size, while the results for shape indicated the need for continued work in the definition of particle shape.

Jan 1, 2012

By M. Rossouw

The paper sets out the strategic importance of South Africa?s mining and minerals sector to the national economy. It relates how inexorable and accelerating urbanization and industrialization in emerging markets, especially in China and India, will translate into sustained demand for the minerals that South and southern Africa have in abundance. It warns that while countries buying raw materials from South Africa use these inputs as the basis on which to build value-added, employment-creating industries, South Africa is failing to exploit the economic benefits inherent in its mineral wealth, exacerbating its shortage of skills.

Jan 1, 2011

The Proceedings of the above Symposium have been edited and published by the Symposium Committee. The Symposium was sponsored by the Australian Coal Association, the Joint Coal Board, and the United Nations Economic Commission for Europe. The Symposium was very well attended, with presentations from fourteen countries, including all the major coal-producing countries of the world. The Proceedings are presented in two parts: the Symposium Part and the Workshop Part. The Symposium Part deals basically with the theoretical aspects of outbursts and high-gas emissions in mines, while the Workshop Part is more practically oriented and describes case studies, and the management systems, and drilling technologies used in underground mines.

Jan 1, 1996

I. Book review Legal and institutional arrangements in minerals development. Edited proceedings of a workshop organized jointly by the VN. Department of Technical Co-operation for Development and the German Foundation for International Development (DSE), held in Berlin in August 1980. London, Mining Journal Books, 1982. Soft, 228 X 149 mm, xi + 223 pp. Approx. R30 + GST. Reviewer: M. J. Martinson 2. New books Strength of metals and alloys (IOSMA 6). R. C. Gifkins (Editor). New York, Pergamon, 1982. Approx. 1200 pp. 3 vols. V.S. $220. Deformation-mechanism maps. The plasticity and creep of metals and ceramics. H. J. Frost and M. F. Ashby. New York, Pergamon, 1982. Approx. 250 pp. V.S. $60. Pressure diecasting, Part 2. The technology of the casting and the die. D. F. Allsop and D. Kennedy. New York, Pergamon, 1982. $ V.S. 27.50.

Jan 1, 1982

By A. Tello

Variography was introduced by Dr. Pierre Gy to monitor a process, in the sixties. Later on, Francis Pitard extended this concept, building a complete system of variographic controls for different applications. Nevertheless, the existence of information about its use as a way to effectively control plants has been limited. There are infinite areas where variography and chronostatistics can be used. In this paper, two different cases related to gold and silver recovery, through well known but complex metallurgical routes are studied. The use of effective management of process variability software (EMPV) has shown to be a suitable solution to clarify problems at the plant and, consequently, a solution to the encountered problems has been proposed. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in depth way. Once the ore has been extracted from the mine, sampling is necessary at each sequence of the metallurgical process involved. As a first example, leaching of the ore with cyanide in agitated tanks is another case of a complex metallurgy. The aim of the process is to know about residual values in the tailings in order to optimize process. As a second example, leaching of gold and silver in ore heaps, has to be optimized in terms of time, reagents consumption and, of course, in predicting a reasonable recovery. This last issue appears to be crucial. After cyanide leaching at the heaps, a carbon in columns process is involved, where there are a series of carbon loaded columns that are submitted to a dynamic process of load and unload, to finally deliver an enriched solution to the precious metal electrowinning plant. In both cases, variography has been a good approach to show metallurgists ways to improve the operation.

Jan 1, 2009

By H. C. Van Der Merwe

In the 21st century, dynamic, accurate digital 3-D geological models are essential to the pursuit of safe, efficient and profitable mining. This is particularly true for the deep-level underground mines in South Africa. The Sirovision® solution is a collaboration project between the Australian CSIRO (Commonwealth Scientific and Industrial Research Organisation), Datamine Software Ltd. and AngloGold Ashanti Ltd (AGA). The purpose of the project is to provide a fully integrated digital rock face imaging, geological mapping and modelling system for the AGA gold mining operations. The CSIRO-developed Sirovision® Stereo Camera Rig (SCR) consists of two digital cameras, alighting system, a laser guidance system and image processing software. The imaging system works on the principles of photogrammetry, i.e. overlaying of two 2-D images with a central focus point, with mathematical algorithms extracting 3-D information from the 2-D image pair. The output from matching several image pairs is a computer-generated, full 3-D, virtual copy of the mining excavation. The image resolution and relief ares of sufficient quality to distinguish different rock types and structural contacts. Functionality within Datamine Studio3 is used to add geological intelligence to the 3-D images provided by Sirovision®. The geologist identifies and ?draws? lines representing geological features directly onto the image. By utilizing the inherent ?topography? of the 3-D image, the software is able to convert the lines into 3-D surfaces, ready for use in the 3-D geological model. Subsequent to promising underground test results from AGA?s Sunrise Dam Gold Mine (SDGM) in Australia and other mining operations worldwide, it was decided to test the Sirovision® system in the South African deep-level gold mines. The first underground tests at Moab Khotsong Mine began in January 2009. The objectives of these tests entailed the capturing of 3-D images of selected development ends, mapping of geological features onto the 3-D images and integration of the mapping data with the 3-D geological model. Some downsides have cropped up during the feasibility testing, related to practicality of the SCR for acquisition of 3-Dimagery in the deep-level underground operating environment. These constraints will have to be addressed prior to operational implementation. Facing such difficulties is not unusual when attempting to implement new technology in such a challenging working environment and testwork is still in progress at the mine in order to prove the concept of using this technology in a Witwatersrand underground gold mine. The great advantage of the Sirovision® solution is that it offers the geologist the opportunity to work remotely on a 3-D virtual copy of a mining excavation, without the heat, humidity, hazards and time constraints associated with physical mapping in an underground workplace.

Jan 1, 2009

By A. M. Croll

The efforts to mechanize narrow reef tabular orebodies unique to this country, are not new. They began in the early 1900s and have over the last century seen varied rates of progress and success. Efforts to mechanize with the use of scraper winches can be regarded as a success. The scraper winch replaced the hand lashing of ore and development waste into hoppers. The initiatives by Anglo Gold and the then JCI to implement trackless mining equipment into these environments had limited success but in general were looked upon as a failure?at least this is the perception. The Chamber of Mines Research Organization (COMRO) in conjunction with various mining houses tried to make a success of the impact ripper. Diamond wire cutting of the stope face is another, which has been tried and tested. The use of high-pressure water to cut rock has also been trialed. These attempts, amongst others, are just a few of the efforts that have not been successful in the quest to make life at the face safer, more productive and easier for our employees. Against the backdrop of an emerging South Africa, the associated high expectations of historically disadvantaged people within the country, a strong rand, demands for better safety, lower cost of production and more efficient operations, mechanization has the chance to make a difference to Anglo Platinum?s business. Mechanization has certainly changed the way other commodities such as coal, base metals and diamonds are won from the earth. Mining?s image is still one of people crawling around in stopes?a dirty, ?low-tech? business. Anglo Platinum?s latest journey to mechanize its underground operations began in earnest in1998 and has enjoyed some successes and failures. The opportunity to change the way mining is done within the company is there. Technologies are evolving, and the implementation of mechanization can certainly assist with the achievement of the goals referred to above. When mechanization commenced, targets were set for the company to achieve but these have been revised in the light of recent events relating to the strengthening rand and a slow-down in expansion plans. However, the intent to mechanize appropriately in Anglo Platinum still exists.

Jan 1, 2004

The utilization of computer assisted tomography (CT or CAT-scan)as general non-destructive examination (NDE) technique and as research tool for scientists in South Africa, is limited due to the relative unavailability or nonexistence of such specialized analytical equipment. Many medical hospitals are equipped with X-ray CT scanners for the diagnostic examination of patients but do not easily allow paleontologist or other scientist to utilize their very expensive equipment. As from 2003, Necsa hosts the South African Neutron Radiography (SANRAD) and tomography facility where neutrons from the SAFARI-1 nuclear research reactor and their penetrating power as well as X-rays as a complementing tool, are utilized in many R&D applications. This facility is being made available to HEI and specifically utilized by postgraduate students as part of their studies and/or by industry on an ad hoc commercial basis. The capability of these radiation imaging facilities at Necsa will be demonstrated in areas such as paleontology, geosciences and specifically the physical properties of rock and the distribution of minerals in borehole cores, petrophysics to predict the percentage tar/oil/water content within sandstone samples and others. The penetration capability of neutrons through specimens with a matrix of high atomic number (dense materials) and their ability to be attenuated by low atomic number material (light density) makes neutron imaging complementary to X-ray imaging. The capability of X-ray and gamma radiation for relatively easy penetration through specimens of low atomic number allows for viewing of imbedded high atomic number materials and density variation. X-ray micro focus radiography is capable of resolving objects of micro scale size that are micro distances apart whereas X-ray phase contrast radiography utilizes the wave properties of the electromagnetic spectrum of X-rays to clearly define edges of the specimen under investigation. Many applications with neutrons as imaging probe are successfully applied at several facilities across the globe such as at NIST in USA, Neutra at PSI in Switzerland, and ANTARES at FRM2 in Germany, etc, are documented 4?9, through world conferences on neutron radiography, for example. This is achieved through very well thought through and implemented instrumentation from the production of neutrons to their detection and interpretation of the images. The need arose at Necsa to upgrade the current facility from 42-year-old technology, which was successfully applied in neutron imaging over the past 10 years, to state-of-the-art technology found at European facilities. This initiative started under the auspices of an IAEA-TC programme for the period 2007?2010.

Jan 1, 2008

By H. W. Glen

The use of a personal style (mainly active voice and first person) makes technical writing more pleasant to read, and helps the writer to express his meaning clearly and to avoid many of the stylistic errors normally encountered in that type of writing.

Jan 1, 1979