Search Documents

1. Mine drainage constitutes surface or ground water which flows from mines or mine sites and is usually characterized by concentrations of acidity or alkalinity. 2. The regional geology controlling the ground water flow pattern in conjunction with the life cycle mining plan can serve as a basis for making decisions about quality of water that can be expected to be encountered. 3. In regard to the prevention and control of acid water formation in underground coal mines, much is left undone in research and education: (A) Very little literature is available on this specific subject although much has been written on water management in underground mines. (B) Little or nothing is contained in the text books and curricula used in mining departments at colleges and universities with the result that educational offerings may be seriously deficient in these areas. 4. Prohibiting water entry into underground coal mines is the best method of preventing water pollution. Since this is not possible as mining operations are extended, preventing water or oxygen from contacting acid producing material may offer the next best alternative. 5. More emphasis is needed during the mine planning stage on steps to prevent water pollution. Such life cycle considerations as type of mining, sequence of development and spatial configuration as well as the elements of the drainage network and final network organization and extent must be considered.

Jan 1, 1970

By Hillary W. St. Clair

The effective coefficient for rate of reduction of a sample of granular iron ore may be determined by passing the reducing gas through a bed of the are at constant flow rate and periodically analyzing the effluent gas, The method of analyzing the data is based on a mathematical model that takes into account the variation in composition of the gas and solids with time and position in the bed. A method is described for determining the value of the rate coefficient that gives best agreement between the observed and calculated analyses of the effluent gas.

Jan 1, 1967

Increase the safety of underground mine workers by minimizing hazards associated with rerailing mine cars after derailment. Background and Approach A serious operational problem in underground mines is the task of rerailing mine cars. Current rerailing practices are not only hazardous but are inefficient as well. Most methods involve pulling the derailed car back onto the track with a locomotive. This causes damage to the road bed and is not effective on curves or in situations where the car's wheels are too far from the rails. Jacks, wooden props, and pry bars are also used to raise or lower cars back onto their tracks but methods involving these tools require much strenous manual effort by mine workers, thus posing possible serious injuries. The problem is further compounded by the cramped, narrow confines of the underground mine environment which allows no space to permit use of cranes or other surface railroad rerailing techniques. The Bureau of Mines, aware of these problems, investigated improvements in current underground rerailing methods. Through a cooperative effort with Hoesch MFD, a system was designed and modified that can be easily carried into the mine by workers and quickly assembled at the derailment site. The system is hydraulically and pneumatically powered rather than reliant upon manual operation.

Jan 1, 1986

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

Minimize the risk of conveyor belt fires in underground coal mines by improving the accuracy of and means by which flammability data are acquired. Approach Develop a large, laboratory-scale flammability test for mine conveyor belting that realistically assesses its fire resistance. Background A conveyor belt fire in an underground coal mine is a serious threat to life and property. To minimize the risk of belt fires, the U.S. Code of Federal Regulations (CFR) for underground coal mines requires approved fire-resistant belting. Despite this precaution, about 25% of the reportable underground coal mine fires from 1983 through 1988 involved conveyor belting. In several instances, hundreds of feet of belting were destroyed. The current flammability test for fire-resistant belting is specified in 30 CFR, Part 18.65 and is conducted by (be Mine Safety and Health Administration (MSHA). The small-scale test is performed in a 21-in-cubical chamber with 6-in-long by 1/2-in-wide belt samples. To evaluate the flammability of conveyor belting under more realistic conditions, the U.S. Bureau of Mines conducted large-scale fire tests of belting. The large-scale data were then utilized in the development of an improved laboratory-scale flame test for fire-resistant belting.

Jan 1, 1991

By F. P. Haver

A procedure is described for recovering both lead and sulfur from galena flotation concentrate, comprising the following steps: (1) Aqueous oxidation of the concentrate, using ferric sulfate to convert lead sulfide to sulfate and to give elemental sulfur; (2) regeneration of the ferric sulfate by electrolysis in a diaphragm cell; (3) treatment of the leach residue with ammonium carbonate solution to change the lead to an acid-soluble form and to produce ammonium sulfate as a byproduct; (4) solution of the lead carbonate in hydro-fluosilicic acid followed by electrolysis to recover the lead as metal and regenerate the acid; and (5) extraction of the elemental sulfur from the final residue with an organic solvent. About 90 percent of the lead can be recovered by the above method as 99.9-percent-pure metal, together with two-thirds of the sulfur--half in the elemental form and half as ammonium sulfate.

Jan 1, 1970

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

By R. V. Ramani, C. B. Manula, A. Owili-Eger

• MINE VENTILATION NETWORK PROBLEM (NATURAL SPLITTING; FIXED • QUANTITY BRANCHES; METHANE SIMULATION; NETWORK TOPOLOGY REVISION; • ABSOLUTE PRESSURE) • NFIXB = NO. OF FIXED QUANTITY BRANCHES • DD(I) = AIR QUANTITY ASSIGNED TO FIXED QUANTITY BRANCH I, IN KCFP • NFBPF = NO. OF FIXED QUANTITY BRANCHES PLUS FAN • NFBPFG = NO. OF FIXED QUANTITY BRANCHES PLUS FAN PLUS METHANE • EMISSION BRANCHES • NBWNVP = NO. OF BRANCHES WITH NATURAL.VENTILATION PRESSURE • NVP(I) = NATURAL VENTILATION PRESSURE ASSOCIATED WITH • THE I-TH BRANCH • NF = NUMBER OF FANS • NB = NUMBER OF BRANCHES • MAXIT = MAXIMUM NUMBER OF ITERATIONS • MAXJ = MAXIMUM NUMBER OF JUNCTIONS • NJ = NUMBER OF JUNCTIONS INVOLVED IN THE SOLUTION * NM = NUMBER OF MESHES • NP = NO. OF POINTS TO DESIGNATE FAN CHARACTERISTIC * Q = QUANTITY OF AIR FLOW IN KCFM • R = RESISTANCE OF AN AIRWAY • WIDTH = AIRWAY DIMENSION • LENGTH = AIRWAY DIMENSION • HEIGHT = AIRWAY DIMENSION • SUMNVP = SUMMATION OF NATURAL VENTILATION PRESSURE FOR ANY MESH • X (I) = QUANTITY OF AIR, IN KCFM, ASSOCIATED WITH THE I-TB POINT • ON A FAN CHARACTERISTIC • E = ERROR FOR CONVERGENCE • FF = FRICTION FACTOR • FX(I) = FAN PRESSURE, INS INCHES OF WATER GAGE, CORRESPONDING • • TO A QUANTITY X(I) • H = HEAD LOSS IN INCHES OF WATER GAGE • I = BRANCH NUMBER • J, J1, J2 = JUNCTION, J1 AND J2 ARE TWO NODES WHICH DEFINE A • BRANCH • KEY = NO. WHICH SIGNALS THE TYPE OF FAN CHARACTERISTIC TO BE • EXPECTED

Jan 1, 1975

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

Although haulage truck collisions account for only a small percentage of haulage accidents, the likelihood of severe injury, or even death is very high when such a collision does occur. Most rear-end collisions also result in considerable equipment damage, creating a need for expensive repairs. To improve collision protection, some southwestern surface mines have, for several years, been fabricating and using extended bumpers. In cooperation with these mines, the Bureau of Mines has worked to improve this technology by evaluating the structural requiremnts of extended bumpers. How Extended Bumpers Help The Bureau found that when one large rear-dump haulage truck collides with the rear of another an extended bumper protects the driver of the vehicle that is struck by dissipating the impact energy into the rear tires and pushing the whole vehicle forward. An extended bumper also prevents the box on the truck that is hit from penetrating the cab of the other truck-a typical and serious collision hazard. A further advantage derives from the wide design of the extended bumper which helps prevent damage to truck ladders, thereby minimizing any entry or exit problems. Extended bumpers also provide safe work platforms at the front of large haulage vehicles.

Jan 1, 1984

By L. E. Schultze

The Bureau of Mines operated a mineral recovery unit to recover metal values from post-flash geothermal brines from the Salton Sea known geothermal resource area as part of its research into the use of plentiful resources. The brine was available for metals recovery after its heat content had been used to generate electricity. The brine source was treated with lime to precipitate the contained iron, manganese, lead, and zinc before injection of the heat-depleted brine into the underground reservoir. Data are presented on the effects of process variables, such as rate and method of lime addition and air oxidation versus air exclusion. Variations in precipitation of metal values, composition of precipitates, effectiveness of slurry thickeners, and methods of treating the precipitates to recover metal values are discussed.

Jan 1, 1982

Assure fail-safe stopping of a mining vehicle immediately following a loss of electric power. Approach A separate emergency brake system which actuates when electrical power is interrupted, was installed on several mining vehicles and tested in a long-term underground mining demonstration. How It Works Separate, spring-actuated brakes, which press against brake discs, are used to stop the vehicle following power failure. To allow norm al movement of the vehicle, hydraulic oil under pres? sure from the vehicle's hydraulic system is directed to a spring? loaded piston in each emergency brake housing. That pressure causes the piston to compress the spring and relieves the spring pressure against the puck, thereby allowing the brake disc to turn freely. See Figure 1 A. If the electrical power fails or if the machine is turned off, a valve in the hydraulic line to the emergency brakes opens. That valve, shown as ?Solenoid Valve (automatic)" in Figure 1, which is normally held closed by its electrical solenoid while the vehicle is electrically powered, is opened by the spring in the valve assembly. The pressure in the hydraulic line which is connected to the emergency brakes then drops to

Jan 1, 1978

By Edward Thomas

"HISTORYThe origin of roof bolting as a means of roof support is obscure. During the past 23 years a method was developed by the. St. Joseph Lead Co: at its mines in southeastern Missouri, ranging from occasional use of single bolts with small bearing plates to systematic networks of bolts utilizing continuous bearing plates. Officials of this company are not certain which of its employees suggested their use. Many instances of occasional use of roof bolts have come to light during the past few years in widely separated mining districts, such as in West Virginia, Alabama, Illinois, Colorado, and Wyoming bituminous coal mines, and in Pennsylvania anthracite, Lake Superior iron, and Colorado lead-zinc mines. A few of the known installations have boon in place as long as 40 years.These installations usually were made to supplement wooden timbering in mine openings whore space was constricted, although it had been reported that roof bolting was started as a systematic moans of roof support in at least three instances but was abandoned because the cost of installation was excessive. The extra expense above that of conventional timbering could not be recaptured through economies resulting from increased efficiency, such as would be gained through mechanized mining.Roof bolting was first mentioned in mining literature in an article by W. W. Weige 3/ in Engineering and Mining Journal of May 1943, in which he described the use of bolts with 4-inch channel bearing plates in mines of the St. Joseph Load Co."

Sep 1, 1950

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant's electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981

Improve safety at mineral operations that use cyanide leach solutions to recover precious metals from finely ground ores, Approach Provide an alternative, non-acidic means of cleaning processing systems such as the State-of-Maine filter system, thereby reducing the exposure of workers to toxic hydrogen cyanide gas (HCN), The Problem Many gold and silver mining operations use cyanide solutions to dissolve gold and silver from ores. The precious metals frequently are recovered from pregnant leach solutions by the Merrill-Crowe recovery process, whereby gold and silver is precipitated with zinc dust. When that method is used, suspended particles in the leach solution must be filtered out before zinc precipitation can occur. This filtering is accomplished with small packaged plants, such as the State-of-Maine (SOM) filtering system. Unfortunately, the filters become clogged with calcium carbonate scale after about 2 to 10 days of operation and must be cleaned before further precious metals recovery operations can continue, Cleaning the system is a hazardous task because the acid is not compatible with the alkaline cyanide leach solutions, and toxic hydrogen cyanide (HCN) gas may be produced when the acid and solution are mixed. That gas, if breathed or contacted with the skin, can cause cyanosis which may induce nausea and even asphyxia and death. To reduce this danger, the Bureau of Mines has devised a safer method of cleaning clogged filters,

Jan 1, 1986

By Travis Q. Lyday

Gold continued to dominate mineral production in the group of volcanic islands and atolls of Melanesia in the southern Pacific Ocean, which comprise the British Commonwealth nation of Fiji. The Fijian mineral sector, however, remained of minor importance in terms of export earnings, Government revenues, and employment to the economy of the country, which was primarily agrarian with sugar as its mainstay. The Vatukoula gold-silver mine on the north side of the main island of Viti Levu remained the largest and most important mining operation, as well as Fiji's only operating metalliferous mine. In October, Western Mining Corp. (Fiji) Ltd. (WMCF), a wholly owned subsidiary of Australian-registered Western Mining Corp. Holdings Ltd., increased its interest in the Vatukoula joint venture from 10% to 20% by exercising its option with Emperor Gold Mining Co. Ltd., also of Australia. The assumption of mine management operations at Vatukoula in 1983, with its attendant influx of additional capital and technological expertise, enabled WMCF to increase both efficiency and output at the mine during 1984. Higher output was obtained owing to an increase in underground ore production, which was partly offset by a reduction in opencut tonnage, as well as to modifications in the recovery circuit. Rate of recovery increased from about 15% to over 82% of the gold contained in the ore and from about 40% to 45% of the contained silver.

Jan 1, 1986

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

To cool hot working environments in deep mines more efficiently, while substantially reducing the maintenance required by presently used cooling coil heat exchangers. Approach A mine's chilled water supply cools fresh air enroute to hot working areas, in an improved, direct-mixing heat exchanger. How It Works Warm, fresh ventilation air traveling through the mine's ventilation tubing enters the lower portion of the cooler heat exchanger through a large round opening designed to accept the ventilation duct. This air flow is turned upward and evenly distributed by egg-crate lattice and pair guide vans at the bottom of the cooler. On the diagram, warm air enters at the bottom left. As the air moves upward through the cooler, it passes through a plastic or wire mesh pad which is arranged so that it offers the most resistance to upward airflow immediately above the cooler inlet: this more or less equalizes the upward air flow along the length of the cooler. The air next moves through the cold water sprays, and then through a wire-mesh demister pad before exiting from the cooler at the top right. Cooling of the air is accomplished in several stages. As the incoming air passes through the lower plastic or wire mesh pad, it is exposed to water flowing downward through the pad to the water sump. This is water that has fallen from the sprays or dripped from the upper wire-mesh mist eliminator. This water is slightly warmer than the spray water since it has already done some cooling,

Jan 1, 1981