Search Documents

By M. M. Fine

A satisfactory mean: of beneficiating a Brazilian phosphate rock was developed in a mineral-dressing-research study by the Bureau of Mines. High-grade concentrates well ever the specified minimum grade of 70 percent tricalcium phosphate, were produced, with goad recoveries by agglomerate tabling and flotation. A lower gads but usable secondary product was recovered by sedimentation of the minus-200-mesh fraction of the ore. The ore wan representative of an extensive deposit recently discovered near Recife in the State of Pernambuco, Brazil, which will be exploited in a plant planned to eventually produce at the rate of 500,000 tons of concentrate annually. Although Brazil has been reported to Lave a substantial reserve of phosphate rock,3/ the country has never been more than a small producer of this commodity. From 1945 to 1950 the highest production of phosphate rock attained in Brazil amounted to 10,421 tons. Production in 1949, the most recent year for which figures are available, was 4,553 tons.4/

Jan 1, 1954

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974

By Karl C. Dean

The Bureau of Mines studied the precipitation of copper from dilute acidic sulfate solutions using shredded automobile scrap in a rotary drum. The tests established that the scrap in the rotary drum precipitated copper faster and more completely than shredded, detinned, tinplate scrap in a launder, with comparable iron consumption. Although power is required to rotate the drum, the faster precipitation and continuous recovery of cement copper are advantages of the tumbler method. Cost evaluation indicates that the rotary drum method, which uses relatively low-cost and readily available shredded automobile scrap, is competitive with the launder method, which uses relatively high-cost shredded tinplate scrap or detinned shredded cans.

Jan 1, 1968

By S. L. Payne, E. F. Foerster, C. W. Schultz, G. R. Zellars

The vapor pressure of copper in a series of liquid copper - nickel alloys was determined by the carrier gas method . The activity and activity coefficient of copper were calculated over the entire range of alloy composition . These data show a slight positive deviation from ideal behavior . The activity coefficient of copper was highest ( 2.10 ) at 0.05 mole fraction copper and approached unity at concentrations above 0.85 mole fraction copper . The results for nickel were calculated from the copper data by the graphical integration of the Gibbs - Duhem equation .

Jan 1, 1964

By Donald I. Kurth

This Bureau of Mines report describes the development and application of a computer model of aquifer hydrology associated with in situ leaching of uranium. The model provides uranium resource developers with a simulation of leachant flow characteristics in a preproduction or pilot five-spot leaching operation. Various types of aquifers are modeled using closed form solutions of the partial differential equations describing the change in fluid head (pressure) as the leaching operation is carried out. User-supplied descriptive input consists of aquifer, well, and leachant flow characteristics. Numeric and graphic outputs such as isopressure, iso-velocity, and isotime contours are available. A typical application is shown.

Jan 1, 1978

By David A. Benjamin

In 1989 and 1990, the Bureau of Mines conducted a mineral resource investigation of the 122,000-acre Trinities study area, located in the Trinity Mountains of south-central Idaho. No identified mineral resources were delineated during this study. There are 58 lode mining claims within the area. Five localities contained elevated metal concentrations which may indicate precious metal mineralization at four localities and molybdenum-precious metal mineralization at another. Four of the five localities appear to form a northwest trend through the center of the study area. Twenty-eight individual sites contain anomalous concentrations of gold, silver, bismuth, molybdenum, and beryllium.

Jan 1, 1991

By Hal H. Engel

This publication was written in response to numerous requests for information about the Federal Bureau of Mines' "Demonstrated Lecture on Flame Propagation and Permissible and Explosion-Proof Electrical Equipment." The requests came principally from: (1) Persons wanting to know more about the demonstration before requesting it for groups they represented; (2) persons wishing advance information to help publicize a meeting where the demonstration was to be given; and (3) members of audiences desiring something to help them remember the salient points, facts, and figures presented during the lecture and demonstration. The purpose of the demonstration that accompanies the lecture is to show: (1) Variations in flame speed and pressure at various percentages of flammable gas within the flammable range; (2) effect of flame speed on the "pressure piling" within the area confining the mixture; and (3) the application of flame speed and pressure piling to the combustion of surrounding gas and to the design and maintenance of electrical equipment used in hazardous locations.

Jan 1, 1960

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

By Richard F. Hewlett

The mining industry utilizes a vast store of knowledge, wisdom, and engineering talent in designing mining systems. However, the complexity of the required systems and the presence of numerous variables frequently necessitates raking important decisions without having adequate accurately detailed information. That many of the decisions made in the past were nearly correct, in the long run, is substantiated by the number of successful mining enterprises that exist in the world today. Subsequent to 1940, the disciplines of operations research and systems engineering were developed. The disciplines have produced methods of providing better information to persons responsible for making decisions.

Jan 1, 1963

By George J. Conroy

This Bureau of Mines publication describes several fault locators and methods, including time domain reflectometers, a frequency domain reflectometer, tone generators, an infrared method, the Murray loop method, and high-voltage "click" methods. The Bureau of Mines has been conducting research into these methods for several years, to improve mine safety and facilitate production through rapid, safe location of trailing-cable faults. The problems encountered in practical applications are discussed, and schematic diagrams of several instruments fabricated by the Bureau are presented. Since no present single method of locating trailing-cable faults is universally applicable, a kit composed of several of the more promising fault locators is advisable.

Jan 1, 1978

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

By Sidney Katell

An estimated capital investment of $76,499,800 will be required for a plant designed and built to produce 90 million standard cubic feet per day (std.c.f.d.) of synthetic pipeline gas through Lurgi gasification of bituminous char. This investment figure does not include the pretreatment plant, the cost of which is assumed to be reflected in the cost of the char fed to the gasification system. Shift conversion, C02 removal, and methanation are required after gasification in the Lurgi unit to make a gas suitable for pipeline transmission. Capital investment data are based upon equipment costs, January 1959. Based on a 90-percent or 330-day operating year, the operating cost before profit and Federal taxes with the char price as a variable will amount to the following: [ ]

Jan 1, 1959

By T. A. Johnson

Recovering from low demand in 1975, raw mineral production in the United States maintained a steady climb in value and quantity throughout 1976, keeping pace with the gross national product (GNP), which increased 11.5% compared with that of 1975. The minerals industry, in the past, has met ever-increasing demand while keeping production costs to a minimum. To maintain this capability, technological research and development of more efficient processing methods must continue. The role of Government and its increasing involvement in minerals industry actions received unfavorable comment from various segments of the industry in 1976. Government pricing controls were of concern to most industrial firms marketing like products. Public land withdrawals in large blocks were of concern to the mineral industry.

Jan 1, 1978

By P. G. Barnard

The Nation's steel industry is largely dependent on shipments of manganese from foreign sources for steel production. An adequate substitute for the manganese requirements of our present steel technology would improve our national self-sufficiency and also contribute substantially to the conservation of our manganese resources. As each of these objectives is a major interest of the Bureau of Mines, possible substitutes for manganese in steel were investigated. Titanium was selected as the most promising substitute because the published results of several investigations indicate that titanium would perform the most obvious function of the manganese in steel: The elimination of iron sulfide and its deleterious effects. The investigation involved extending the published data on titanium additions in steel to provide enough information for an accurate evaluation of the practical value of the substitute. Therefore, quantitative data were obtained on the partition of sulfur and carbon between iron and relatively small titanium additions.

Jan 1, 1962

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals4/ and. investigations of their chemical and physical properties.5/ The coal represented by the sample from weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By R. L. Montgomery

Heats of solution of cerium metal and cerium (III) chloride in hydrochloric acid were measured. The standard heat of formation of the aqueous cerium (III) ion at 25° C is -166.1 ± 0.3 kcal/mole. Heats of solution of cerium (III) chloride in hydrochloric acid are consistent with the existence of a complex CeC1++ having a stability constant of 1 and a heat of complexing of 5.4 kcal/mole.

Jan 1, 1962

By D. R. Tesarik

An instrumentation and numeric modeling study was conducted by the Bureau of Mines at the Magmont Mine in Bixby, MO. An isolated section of this room-and-pillar mine was monitored with borehole and closure extensometers during a pillar recovery program to determine stress redistribution. In situ stress measurements were taken in the rib before pillar extraction began. Sample cores from the boreholes were taken for analysis of the properties of the host rock in the laboratory. The extensometers recorded no measurable displacements during most of the operation. Two-dimensional, finite-element; three-dimensional, finite-element; and three-dimensional displace-ment discontinuity codes were used to model the area of study. The finite-element models were run with two initial stress conditions, i.e., stress due to gravity only and stress obtained by in situ measurements. Horizontal stresses in the models reduced the calculated factor-of-safety in the mine back by up to a factor of 10, but did not have a significant effect on calculated pillar stability.

Jan 1, 1989

By Charles L. Kusik

As part of an effort to establish processes that could be exploited in case of adverse changes in international chromium production and trading patterns, this study was sponsored by the Federal Emergency Management Agency (formerly the Federal Preparedness Agency) through the Bureau of Mines, to experimentally determine the feasibility of recovering chromium from critical scrap metals containing significant quantities of this element. Based on a conceptual pyrometallurgical chromium recovery flowsheet developed at Arthur D. Little, Inc., the experimental program described in this report demonstrated key process steps for the recovery of chromium as ferrochromium in a batch process. The process involves oxidation of chromium into a slag phase, subsequent separation of the slag phase from the remaining metal, followed by reduction of chromium from the slag phase to produce ferrochromium.

Jan 1, 1981

By M. C. Irani

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1979

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005