Search Documents

By B. F. Naylor

"INTRODUCTION Investigation of the physical properties of electrolytic manganese and its alloys has constituted a part of the program of the Bureau of Mines for several years, and already extensive data have been reported. 3-14/ Heat-content measurements above 25° C. of pure manganese 15/ were completed recently at the Pacific Experiment Station of the Bureau, and the results obtained removed many of the inconsistencies in previously reported data. This paper reports heat-content data of seven manganese-copper alloys, varying in composition from 25 to 90 percent man-ganese. The alloys, obtained from the Salt Lake City Station, 16/ had been quenched from 850° C, and cold-worked. Without further heat treatment, heat-content measurements of each of these alloys were made at 100° or less temperature intervals from 450° to 850º C., as it was considered likely that any abnormal behavior of the specific heat would be found in this temperature range. Also, a portion of each alloy was heat-aged at given temperatures for periods of time thought sufficient to reach phase-equilibrium; then the heat-contents above 25° C. were determined at the aging temperatures. (Heat-aging was done at approximately 450°, 550°, 650°, 750°, and 850° C.)METHOD AND MATERIALSThe heat contents were determined by the ""drop"" method in a previously described apparatus. 17/ The calorimeter was cali-brated with electrical energy, measured in international joules, and the results were converted to the conventional thermochemical calorie by the relation, 1 cal. = 4.1833 int. joules."

Jan 1, 1946

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By John R. Bitler

A computerized napping system was developed by the Bureau of Mines to provides procedures for the rapid and inexpensive display of coal reserve data. Mapping system output consists of two types of maps, point distribution and contour (isopleth), which can be produced for data (coal analyses) associated with a point location (outcrop, drill core, or mine samples). These locations can be in the form of latitude and longitude or Universal Transverse Mercator (UTM) grid coordinates. The mapping area can range in extent from as small as a single county to as large as a multistate region. The mapping system utilizes programs developed at Harvard University, in addition to several modifications developed by the authors. The primary advantage of this system is that it enables the display of a rapidly changing data base and computerized map generation without the intermediate steps of digitizing and overlaying to produce base maps. The mapping system is applicable to any regional mineral reserve or resource study for which point location data are available. Included are example maps of the distribution of data points and contouring for sulfur content of the Upper Freeport coalbed in this western Pennsylvania demonstration area.

Jan 1, 1977

By L. C. IlsLey

The first thing to consider in prevention of electric shock is the voltage of the circuit. No person can be sure that he will not be killed, even from a 110-volt circuit, if he makes proper contact with the circuit so as to cause the maximum current to pass through his body. As the voltage is increased to 250 volts, 500 volts, or 2,300 volts the danger from contact with the electric circuit is increased, Alternating current of the same nominal voltage is possibly more dangerous than direct current. Experience has taught us that both will cause death, and that if the fatalities from this source are to be kept low, certain precautions in the guarding of circuits must be observed.

Feb 1, 1929

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D.2 Principal Types of Coating A Sodium Silicate Sodium silicate is a good fire retarder when freshly applied, but it loses its effectiveness if the relative humidity is at all high, thus exposure to a relative humidity exceeding 65 percent causes a serious decrease in the effectiveness after only one month. In fire, sodium silicate swells to a frothy mass (intumescence) which hardens and insulates the wood against heat. This property is destroyed by exposure to moisture. Manufacturers of many of the proprietary paints containing silicates state that their products have overcome this difficulty The reagent may be applied alone, or, better, in a mixture with lime-water and common salt, or with inert fillers such as kaolin or asbestos. B Ammonium Phosphate Strong solutions (25 to 35 percent) of monammonium phosphate or diammonium phosphate give good protection. Two or three coats of hot solution should be applied either with a large flat brush or an ordinary paint spray gun The solution should be applied as hot as possible, as this improved penetration, and it should be the aim of the operator to apply 4 lbs of reagent, i e , one gallon of 33 percent solution to every 100 square feet of surface

Jan 1, 1976

By Sinisa M. Djordjevic, Isaac A. Zlochower, Kevin J. Liekhus, Cindy A. Loehr, Kenneth L. Cashdollar

An experimental program was conducted to evaluate the accuracy of some current methods for predicting the flammability of gas mixtures containing hydrogen and flammable or nonflammable volatile organic compounds (VOCs) in air The specific VOCs tested were toluene, 1,2-dichloroethane, 2-butanone, and carbon tetrachloride. The lower flammability limits (LFLs) of gas mixtures containing equal molar quantities of the components were determined in a 19.4-1 laboratory flammability chamber using a strong spark ignition source and a pressure criterion for flammability. All but one of the LFL values for the individual components were in agreement with earlier literature values. However, the LFL of l,2-dichlorocthane was found to be significantly lower than the range of values reported for previous determinations in smaller chambers. Two methods for calculating the LFL of mixtures were considered. The Group Factor (atomic) Contribution Method was determined to he generally more accurate than the LeChatelier Method for estimating the LFL of the gas mixtures reported here, although the LeChatelier Method was usually more conservative. The Group Factor Method predicted higher values (nonconservative) for the LFLs of several mixtures than were experimentally measured. For the case of a mixture of hydrogen and carbon tetrachloride, the Group Method estimation of the LFL was seriously in error.

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By U. E. Brown

This papery describing the mining methods employed by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the United States. The Bunker Hill and Sullivan mines are situated in the western part of the Coeur d'Alene district at Kellogg, Shoshone County, Idaho. The mines were discovered during the summer of 1885 and except for two short periods of labor trouble, between 1890 and 1900, have been in continuous operation. About 575 men are employed at the mine. The production is about 1,400 tons of lead-silver ore per day. This is treated in the company's concentrator and smelter at Kellogg.

Jan 1, 1931

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

The results of a Feasibility and Design Study of Surface Impregnation Equipment to be used for Chemical Stabilization of Coal Mine Structures are described in this report. The study was sponsored by the United States Department of the Interior, Bureau of Mines, under Contract H0210055. This program was undertaken as an essential part of the Bureau of Mines Chemical Ground Stabilization Program. The responsible prime contractor was The Eimco Tunneling and Mining Machinery Division of the Envirotech Corporation. The Rocketdyne Division of the North American Rockwell Corporation performed part of the feasibility study and design and testing of the metering and feed system as a subcontractor to Eimco.

Jan 1, 1972

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure, but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of Intolerability which accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a non-odorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

By J. W. Thompson

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protect¬ing exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

May 1, 1921

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of gold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium which such samples contain. It is much more difficult to assay black sands, or concentrates, produced in large-scale placer-mining operations. These products are usually much harder and more abrasive than the beach black sands. They also contain numerous metallic particles resulting mainly from wear on the mining machinery. These particles consist chiefly of iron or steel but also contain lead, copper, and alloys such as babbitt, solder, brass, ferrosilicon, etc. Fairly large particles of gold are often found. Some samples will contain as much as 10 percent of such metallic particles. It is not feasible to remove the particles of iron with a magnet and discard them, as they invariably contain gold, sometimes a considerable amount. This gold is attached to the iron particles by rust or wedged into cavities. Scraps of sheet iron are often found which have become tightly folded or rolled and contain gold or amalgam within the folds.

Jan 1, 1934

By F. W. Hoertel

Near-optimum parameters were determined by the Bureau of Mines for vapor deposition of rhenium on heated copper substrates by hydrogen reduction of rhenium hexafluoride (ReF6). High-purity deposits of nearly 90-percent theo¬retical density were obtained with the reaction chamber at 250° C, with an H2 to ReF6 volume ratio of 25 to 1, and with an ReF6 flow rate of 5 grams per hour. Some rhenium deposited as a loose, black powder. When the established near-optimum parameters were carefully followed, this could be minimized but never completely avoided. Varying the reaction chamber pressure, both above and below atmospheric, yielded excessive quantities of rhenium powder. Deposition efficiencies, based on only the coherent metal, ranged between 70 and 75 percent. Massive deposits contained only spectrographic traces of impurities. The average microhardness (Knoop, 100-gram load) of vapor-deposited rhenium was 907. Limited research on the deposition of rhenium-tungsten alloys by reduction of the mixed hexafluorides produced deposits in which linear composition gradients were pronounced; this nonhomogeneity was attributed to the wide variation in optimum hydrogen-reduction temperatures of the two hexafluorides (250° C for ReF6 and 550° C for WF6). Using deposition temperatures between 250° and 550° C did not eliminate the composition variations.

Jan 1, 1967

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of sold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium Which such samples contain.

Jan 1, 1934

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

By R. L. Grayson, S. S. Peng

"Research has been conducted during the past year on a study to correlate respirable coal mine dust characteristics with worker positions and coal seams. The first characteristic of respirable coal mine dust which has been addressed in the correlation study is respirable dust mass concentration. In fulfillment of this objective, two mines operating in different coal seams have been selected for respirable dust mass sampling on both longwall panels and continuous mining sections. At present, sampling has been completed on the longwall panel operating in the first mine, and one half of the planned sampling has been accomplished on the continuous mining section.The first mine sampled is operating in the Pittsburgh coal seam. The average mining height is approximately 78"" with an average of 8"" of bottom shale being mined. The mine is primarily a longwall mine, and continuous mining machines are used to support the longwall.Figure 1 shows the layout of the longwall panel which was sampled. Intake air is coursed via the track heading up to the headgate area. The air splits at the headgate. Approximately 20,000-30,000 cubic feet of air per minute (CFM) is used to ventilate the longwall face and about 5,000-10,000 CFM is routed down the belt entry. Substantial leakage across the gob was noted during the sampling period. An average of 1800 CFM per 100 feet of face leaked through the shields into the gob from #1 shield to #112 shield. A substantial amount of leakage also occurred between the #1 shield and the solid rib of the headgate development panel. The path of the air used to ventilate the panel is shown with arrows in Figure 1. Direction of air flow was opposite to the coal moving direction on the armored face conveyor.A double-drum ranging shearer is used on the face to cut a 30-inch web of coal. Normal practice is to cut from the tailgate to headgate with the leading drum raised and the tail drum lowered for cutting bottom. After reaching the headgate, the shearer is reversed and both drums are lowered for a clean-up pass. The last 40 feet of face on the tailgate is cut on the clean-up pass.The shearer is equipped with 2 banks of 4 water sprays each and 2 large sprays on the headgate end and 1 bank of 4 sprays on the tailgate end. Additionally, sprays are located above bits on the cutting drums. Actual cutting speed was approximately 14-18 feet per minute, depending on conditions.The cross sectional area for air flow on the face was approximately 60 square feet before a pass was mined and 80 square feet after a pass was mined but before the shields were advanced. The cross sectional area at the shearer was about 35 square feet.The condition of both the tailgate and headgate of the panel was good with no signs of significant roof problems. The roof conditions along the face during the sampling period were variable. At times, as much as 3 feet of drawslate fell from the roof for a span of as much as 40 shields. Generally, however, relatively local areas of falling roof were encoun-tered, usually limited to a 10-20 shield span when appearing.Ten days were spent gathering respirable dust samples on the longwall panel. Mine Safety Appliance (MSA) sampling units equipped with 10-mm nylon cyclones, pre-weighed MSA PVC filters, and constant-flow DuPont pumps were used to obtain thesamples. The pumps were calibrated at a 2 liters-per-minute flow rate. The 10-mm cyclone was selected for classifying total dust into the desired respirable fraction in order to obtain ""legally defined"" respirable dust samples for detailed physical characterization."

Jan 1, 1988

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

"The U.S. Bureau of Mines established on August 15, 1983, The Generic Mineral Technology Center for Respirable Dust (Dust Center) within the Mining and Mineral Resource Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University, and in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. In 1986, Michigan Technological University (MTU) was awarded a grant through the Dust Center. The center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health law, which is ""... (to) permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis of any other occupation-related diseases..."" The Dust Center's program is designed to foster an accelerated attack through fundamental research on problems confronting the control of respirable dust in mines. The interactions of the universities and the research program components in the characterization of coal seams, respirable dust particles and the workers lungs are depicted in the logo of the Dust Center.The primary goal of the Dust Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The Dust Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection of dust in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) the relationship of the mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines, and to other dusts such as those generated by diesel equipment. Achieving the Dust Center's goals also involves the training of engineers and scientists, graduate students, and undergraduate students through their respective institutions, and technology transfer to industry. The distribution of personnel in the various universities are presented in Table 1. A directory of Dust Center principal investigators is presented in Appendix 1. A summary of degrees granted and mineral sector employment is presented in Table 2. The subjects of theses developed under the various research projects are presented separately in Volume 7. The center research is fully compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities (see Volume 2). Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease studies are available as a result of the existing relationship between NIOSH and West Virginia University. Figure 1, Respirable Dust Center Projects and Activities, presents the various projects in the five major areas of investigation and the scope of characterized dust samples, the suite of tests, the sampling and dust generation methods, and the size, chemical and mineralogical analysis performed in the center. Table 3 presents a summary distribution of the 95 publications and presentations that have emanated from the center. In addition there are more than thirty presentations made at each annual Dust Center review meeting. The titles, authors and location of presentation for publications supported by the Dust Center are presented in separate publication volumes for 1984 (Volume 3), 1985 (Volume 4), 1986 (Volume 5) and 1987 (Volume 6)."

Jan 1, 1988