Search Documents

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By A. B. Hooker, E. J. Coggeshall

"INTRODUCTION Ignitions of gas at the coal face when a blast is fired electrically are often a tributed to the explosive; but sometimes the ignition cannot be explained satisfactorily in this way-in fact, ignitions have occurred when the detonator has failed explode.The possibility of such electrically by sparks from the blast between poorly insulated leading wires and detonator leg have been recognized. Several countries have provided safe types of single-shot blasting units; some have permitted the use of larger multiple-shot blasting units provided each unit is equipped with a time-limiting switch that prevents unnecessarily long application of voltage on the leading wires after the shot has occurred, the assumption being that the firing line will this be dead before damage to the wires and subsequent sparking can take place. An extensive research was made by a French commission relative to the characteristics of electric detonators and methods of firing. Along other tailings they investigated the probability of ignitions by sparks across the leading wired at the face, also the time and duration of the various events in blasting, such as ignition of the detonators, movement of the coal face, and application of firing current. They suggested, as a means of eliminating or reducing tilt possibility of gas ignitions from the blasting unit, that the timing switch of the blasting unit be designed to disconnect the blasting"

Oct 1, 1934

By E. J. Matson

The Little Castle Creek chromite deposit was examined in February and May 1941, respectively, by W. O. Vandenburg and O. H. Metzger, engineers of the Bureau of Mines. The Federal Geological Survey started a magnetometer survey of the area in November 1940 and completed its work during April and May 1941. Field work by the Bureau of Mines was conducted during May and June 1941. The purpose of the Bureau of Mines investigation was to search for a continuation of the chromite mineralization. The property at one time was the largest chromite producer in California.

Jan 1, 1949

By Clyde M. Pearce

The Lake Superior iron-mining district includes parts of the States of Michigan, Minnesota, and Wisconsin. The laws of each State provide for an industrial commission and for inspection of mines. The following extract from the General Orders on Mines, effective October 25, 1937, issued by the Industrial Commission of Wisconsin, is the only reference to the use of safety catches on mine cages or skips found in the laws and regulations in the Lake Superior iron-mining district: Order 316 - Cages for Hoisting Men. (c) Sides, Gates, and Safety Catches. ***Every cage shall be provided with safety catches of sufficient strength to hold the cage with its maximum load at any point in the event the hoisting cable should break. (d) Testing Safety Catches. The safety catches of cages and skips used to hoist men shall be kept well oiled and in good working order. They shall be tested at least once each month by tying up the cage or skip with hemp rope, lowering a few feet of hoisting cable on top of cage, then cutting the hemp rope, provided that any other system of testing, which is equally effective, may be used.

Jan 1, 1945

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful 'Were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

By Lowell B. Moon

Regardless of how a mineral deposit in first discovered or by whom, any mining enterprise based upon it must pass through a preliminary stage of exploration. The common understanding of ?exploration? among mining engineers is well-expressed by Jackson and Knaebel:3/ Exploration work ranges from that performed by the individual prospector employing only the simplest tool, and equipment to elaborate campaigns involving the expenditure of largo stuns of money end the use of churn- car diamond-drilling equipment, large test-pitting crews, or sometimes a regular mining organization. In any event, the object is to determine as accurately as possible, with the funds available, the size, shape, and other characteristics of the ore bodies and their average value or grade.

Jan 1, 1945

By G. E. McElroy

Economic solutions of problems of mine-ventilation improvement can be found by mathematical analyses of alternative methods of procedure, but, in the case of our older bituminous-coal mines, the airway network is usually so complex that mathematical solutions are too tedious to be practical. Recourse usually is made to extremely costly and uncertain trial-and-error procedures with the existing layout and equipment. The resulting errors often prove costly and sometimes create hazardous conditions. Both the economic and safely aspects of alternative methods of ventilation improvement may be rapidly and cheaply investigation with analogue computers. An electrical analogue computer, designed and built especially for analyzing mine-ventilation-distribution problems, has been placed in service by the Bureau of Mines at its Pittsburgh, Pa., Experiment Station. It is a nonlinear, low-voltage, fluid network analyzer of a type developed by Malcolm S. Mcllroy, professor of electrical engineering at Cornell University. It was designed in close coopera¬tion with Professor Mcllroy and built by the Standard Electric Time Co., Springfield, Mass. It is the seventh unit of this type to be placed in service and the first designed for mine airflow problems. The other six were designed for either water- or gas-distribution analyses. Three are much larger and more expensive units. The largest unit has a capacity of 20 sources, 576 mains, and 180 loads, or regulated-flow paths. The Bureau unit has a capacity of 5 sources, 128 mains, and 48 loads.

Jan 1, 1954

By Raymond F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Albany Metallurgy Research Center has developed atomic absorption spectrographic methods for the rapid analysis of A1203, CaO, Fe203, MgO, MnO, and Si02 in steelmaking slags. The application of these methods is discussed using an inexpensive pressure dissolution system. The overall coefficient of variation is 5 pct. The accuracy is the same as the reproducibility.

Jan 1, 1979

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Nicaragua has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Jul 1, 1930

By Oliver W. Keener

The operation described herein differs from the usual practice in the Tri-State district in two important respects: (1) the ore is loaded into cars which are tramped to the shaft and hoisted on self-dumping cages, and (2) about 30 per cent of the ore is loaded by power shovels. The four-month period covered by the cost data appended at the end of the paper immediately followed a period of about one year during which the mine was shut down, and the expense incident to the resumption of operations is reflected in the costs. The author acknowledges the assistance of C. F. Jackson, mining engineer, U. S. Bureau of Mines, in the preparation of this paper and the compilation of the data.

Jan 1, 1929

By V. F. Parry

Under the present emergency every consumer should store as much coal as he can. Although there is no shortage of coal, there is likely to be a shortage of labor to mine excessive quantities in the fall, and railroads cannot be expected to deliver coal promptly on account of the need for transporting war materials. Some miners must join the armed forces, and those who are left may be unable to mine coal as rapidly as you will need it when winter comes. When the first cold days arrive, there may be a shortage of trucks to deliver coal. Deliveries may be planned in advance, and your turn might not come until it is too late.

Jan 1, 1942

By T. A. Klinefelter

"INTRODUCTION During the development work on sponge iron by the Bureau of lines it was desired to produce a product of maximum density for the furnace. One means of doing this would be to make a plastic mixture of the ground ore and extrude as pellets or large slugs or brick shapes.If a pelletizing Process is employed, the pellets must be strong enough to resist breaking when rolled and tumbled in going through the rotary kiln. If a brick-making process is employed, the brick must be strong enough to withstand handling and considerable pressure when stacked in the kilns.The study had two objectives: first, to find a binder of sufficient strength throughout the early stages of curing and heat treating and, second, to determine the degree of curing and heat treatment necessary to prevent disintegration under normal working conditions.Although the investigation had as its primary objective the processing of sponge iron, the data should interest other industries in which non plastic or poor-bonding slimes are a problem."

Jan 1, 1946

By Lewis C. Karrick

In studying the destructive distillation or pyrolysis of oil shales, the primary consideration is to determine the effects of heat on the organic components of the shale. The impracticability of separating these organic components, collectively known as "kerogen", from the mineral matter with which they are associated renders the problem extremely complex. The behavior of the kerogan in the shale while undergoing the heating process is probably different from that of the same kerogen if it could be isolated and treated under similar temperature conditions, and in fact the results of actual distillations have shown that the physical properties of the mineral matter in the shale may be the cause of much variation in the products of retorting. It must be remembered that the inorganic .material of the shale is a heterogeneous mixture of minerals solidified into a very close-grained compact mass. This mineral mass has a thermal conductivity different from that of the kerogen, thus complicating the problem of even distribution of heat. Furthermore, the temperatures of dehydration of gypsum end some; hydrous silicates are included within the temperature range of the shale distillation, These minerals are frequently present in the shales; and the evolution of water vapors from them will affect the partial pressures of the hydrocarbon vapors evolved from the kerogen, probably tending toward, the improvement of the quality of the oil distillates. Carbonates and sulphides which are also frequently present begin to decompose within this range of temperature, and the gases produced from them may alter the chemical constitution of the oils produced from the kerogen.

Jan 1, 1922

By A. C. Watts, C. A. Allen

In the No. 3 Sunnyside mine of the Utah Fuel Co. a disastrous fire started on the afternoon of August 17 , 1920 , the effects of which are still present in the mine . On account of the extent of the fire , the expense involved in reopening the mine and the opportunities afforded for determining the effects of depleted air , a description of it is worthy of record . This paper is a summary of a more complete report , prepared by the writers , which will be published by the U. S. Bureau of Mines .

Feb 1, 1922

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By R. V. Ramani, K. V. K. Prasad

"Solution of most engineering problems requires, in addition to vast ·numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity; However; it is only .recently that approaches like the expert systems methodology have been developed to ·incorporate the Judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or ""shells"" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development or a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.INRODUCTIONExpert systems (ES) are interactive computer programs which use high quality specialized knowledge in some narrow problem domain to solve complex problems in that domain. These complex problems lack structured and/or standard ways of solution and involve substantial use of subjective and experience based knowledge. One of the first expert systems was MYCIN, developed in 1974, in which subjective and heuristic knowledge of expert physicians was used to diagnose infectious diseases and provide antimicrobial therapy (Buchanan arid Shortliffe, 1984). Since MYCIN, expert systems applications have appeared in other areas such as mineral prospecting (Gaschnig, 1982), configuration of computers (McDermott, 1982) and structural engineering (Bennett and Englemore, 1979)."

Jan 1, 1989

By L. C. IlsLey

From time to time the Bureau of Mines has issued publications dealing with the various classes of explosion-proof mining machinery that have been tested and approved as permissible for use in mines having atmospheres that may become inflammable by reason of the inadvertent presence of gas or dust. These publications are confined almost entirely to description of the features contributing directly or indirectly to the prevention of explosion or shock hazards, and are intended to give inspectors, safety engineers, and others already familiar with the general safety requirements more detailed information on the safety features of the design of a particular machine. As a background for papers describing permissible machines and to avoid the necessity of duplicating descriptions of methods of conducting investigations and tests of such machinery, Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, was pub¬lished in 1929. Three bulletins giving detailed descriptions of the three most numerous types of machines have been issued, viz., Bulletin 313, Permissible Storage-Battery Locomotive and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 392, Permissible Coal-Cutting Equipment.

Jan 1, 1937

By K. D. Luxbacher

Understanding methane emissions in underground coal mines is critical for a safe and productive mine. In addition to reasonable estimation of initial coalbed reservoir parameters, it is also crucial that changes in effective stress due to mining and pore pressure reduction are taken into account due to their effects on porosity and permeability. Primary parameters for estimation of emissions or modeling of the mining environment for this purpose are porosity and permeability which can change dramatically as a result of stress redistribution associated with mining and gas desorption from a large coal volume. These parameters affect the emission rates and ventilation requirements, as well as water inflow into the working environment. Stopping leakage, on the other hand, is a secondary stress dependent factor in estimation of emissions, as convergence of the roof and floor strata, compromising the integrity of the stopping, may result in leakage, making prediction of ventilation requirements difficult. This paper aims to examine the effects of porosity and permeability changes of the coal seam on methane emissions in an underground continuous miner section. The models were developed and executed in a dynamic fashion to simulate an advancing section. Through this process, the changes of effective stress in coal, particularly their change paths, on porosity and permeability were incorporated into the models and methane emissions, concentrations, air requirements, water inflow and possible leakage from the stoppings were investigated using a conventional coalbed methane reservoir model.

Jan 1, 2009