Search Documents

By O. C. Baptist

This report presents results of an investigation undertaken by the Bureau of Mines to determine the clay content of typical petroleum reservoir sands in Wyoming and the effect of clay content on the permeability behavior of the sands. These results should have significance in determining the feasibility of injecting water into the sands for secondary recovery and in estimating the probable damage incurred by these sands if invaded with filtrates from water-base drilling muds. The results of air-, brine-, and water-permeability determinations are given for reservoir sands in three Wyoming fields. The amounts of materials of "fine silt and clay size" (Wentworth scale) in the sands and the types of clay minerals present, as identified by X-ray diffraction methods, are also presented and discussed.

Jan 1, 1955

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By P. G. Clites

A laboratory furnace was developed by the Federal Bureau of Mines for use in studying the interrelationships among variables associated with skull melting and casting high-temperature metals. Although additional work is necessary to determine the extent to which the information obtained by using this furnace can be extrapolated to larger furnaces of the same type, many casting characteristics of metals and alloys can be determined on equipment of this size. This furnace is a laboratory-size, consumable-electrode, skull-casting furnace equipped with a water-cooled copper ladle. The ladle, which is a tilt-pour or over-the-lip type, has a volume of approximately 30 cubic inches and provides up to 20 cubic inches of molten metal for castings. Castings of various reactive and refractory metals, including zirconium, titanium, hafnium, columbium, molybdenum, tantalum, and tungsten, have been produced. In addition, castings of iron, chromium, and copper have been made. The simplicity and versatility of the apparatus would make it useful to metallurgical laboratories preparing cast specimens.

Jan 1, 1961

By R. B. McElwaine

From November 1943 to April 1944, the Bureau of Mines put down 18 churn-drill holes aggregating 2,571 feet of bore in an investigation of the virtually abandoned zinc deposits of the north-central Arkansas district, principally in Marion, Boone, Searcy, and Newton Counties. The ore of this area occurs in flat-lying sedimentaries of the Mississippian and Ordovician ages. Much of the zinc is in the form of carbonate and silicate, although some sulfide has been produced. Preliminary studies resulted in selection for investigation of the Big Hurricane mine in northwest Searcy County, the Spies mine in northeast Newton County, and the Coon Hollow mine in eastern Boone County The comparatively large production of th.ese properties in the past was a factor in the selection. This report describes the work accomplished in the investigation and presents the data obtained.

Jan 1, 1948

By NIOSH NIOSH

This work explores application of a double alkaline leach method to extraction of alumina from Oregon ferruginous bauxitic materials. The process recovers a greater proportion of alumina from high-silica ores than is possible by a conventional single-leach method. This recovery is accomplished by calcining the ore, removing reactive silica in a preliminary dilute caustic soda leach, and then applying a second leach to dissolve alumina. Ores containing up to 15 percent Si~) 35 percent AI;:) Os, and 30 percent Os were examined. Under conditions of treatment established by experimentation, more than BO-percent alumina extraction was demonstrated. When and if conditions demand the use of low-grade materials, the double-leach process is capable of providing millions of tons of alumina from Oregon ferruginous bauxite.

Jan 1, 1963

By Richard G. Sandberg

The Bureau of Mins, U.S. Department of the Interior, is investigating a hydrometallurgical procedure to conserve cobalt, nickel, and copper by recovering the metals from the matte byproducts of smelting Missouri lead ores. For want of adequate processing technology the mattes are now either unmarketable or marginally so. The procedure involves leaching with manganese dioxide and sulfuric acid to obtain copper, nickel, cobalt, lead, and manganese sulfates, and elemental sulfur as expressed by the following reaction: MS + MnO2 + 2H2SO4 ? MSO4 + MnS04 + S° + 2H2O, where M = Cu, Ni, Co, and Pb. The leach solutions, containing near theoretical amounts of sulfuric acid and manganese dioxide at 85° to 100° C, convert up to 98 pct of the cobalt, nickel, and copper in the mattes to sulfates in less than 2 hr. As they are formed, the cobalt, nickel, and copper sulfates are dissolved leaving a residue of lead sulfate, lead, sulfur, and gangue. The soluble metals are recovered from the leach solutions by caustic and sulfide precipitation, and the residue returned to the smelter for lead recovery. The manganese can be reclaimed from the spent leach liquor as manganese oxide and recycled to leaching.

Jan 1, 1979

By Victor E. Kral

The Modarelli iron deposit , formerly known as the Requa iron deposit , is 44 miles by road south of Palisade , Nev . , on the Southern Pacific and Western Pacific Railroads . Construction of 10 miles of new road, which is necessary in case the property is exploited , will reduce this distance to about 28 miles . The deposit was discovered in 1905 , and patent was obtained in 1907 . The present owners obtained title to the property in recent years by paying the delinquent taxes . There has been no production . The ore deposit is a replacement of a Tertiary volcanic believed to be a rhyolite . Except for evidence of slight shearing , the deposit has no apparent structure . Hematite is the principal ore mineral ; it is fine-grained and is associated with very fine-grained apatite and unidentified minerals assumed to be alteration products of residual rhyolite minerals .

Feb 1, 1947

By S. R. Rannels, D. E. Rannels

"I. IntroductionThe alveolar surface of the lung is covered by two populations of pneumocytes, type I and type II epithelium. The type I cell, which accounts for most of the alveolar surface area and provides a highly specialized barrier for gas exchange (Rannels et al., 1991), is poorly understood. Although approaches to type I cell purification have been discussed, they have not been applied widely because of the lack of phenotypic markers to monitor isolation procedures (Dobbs et al., 1988; Danto et al., 1992). In contrast, the type II cell has been studied extensively, largely because of the development of reliable procedures for its isolation and primary culture. Investigations based on the use of purified populations of cultured type II cells have provided convincing evidence to support a role for the pneumocytes both in the maintenance of normal lung function and in the response of the lung to injury (for review, see Rannels and Rannels, 1989).While type II cells can be isolated by a variety of approaches, the protocols used most commonly are modifications of the gradient method of Dobbs and Mason (1979) or of the panning method of Dobbs et al. (1986). Purification of the cells based on density gradient centrifugation is reliable and consistent, with yields of 30 to 40 X 106 type II cells per rat of 230 g body weight. Isolation procedures applied to a minimum of three to four rats provide the best results, as lower cell yields are common with the use of fewer animals. The protocol below is designed to obtain a maximal cell yield from the lungs of six rats.II. Materials and InstrumentationMaterialsCalbiochem: DNase I (Cat. No. 260912); Corning: culture flask, 75 cm2 #25115; Costar: culture plate, 24-well #3424; disposable serological pipette #4101; Elastin Products Inc: elastase #E-134; Falcon: cellulose nitrate membrane filter, 0.22 µm, #7105; conical tube, 50 ml, #2070; culture dish, 100 mm, #3003; culture plate, sixwell, #3046; Fisher: BaS04 , #B68-500; NaCl, #5271-3; NaHC03 , #5233-50; Fort Dodge Laboratories: pentobarbital, #1206-lE; Gibco: Dulbecco's minimal essential medium (DMEM), #430-1600EC; Hanks' balanced salt solution (HBSS), #310- 4185AG; Joklik's modified Eagle's medium (JMEM), #410-2300EC; HyClone Laboratories Inc: fetal calf serum (FCS ), # A-1115-L; I CN Biochemicals (Flow Labora tories): amphotericin B, #16-723-48; newborn calf serum (NCS), #29-121-54; try pan blue, # 19 5 5 32; Na/gene: Erlenmeyer flask, # 100-4116C; Pharmacia: Percoll, #17-0891-01; density marker beads, #17-0549-01; Sigma: gentam1cm sulfate, #G3632; penicillin/streptomycin, #P3539; trypsin inhibitor, #T9128; Tetko: HC- 160 nylon mesh, #3-160-53."

Dec 1, 1995

By Thomas W. Thompson

The Zebulon manganese deposit has been known for a number of years. It is situated about 3 miles east of Zebulon, Wake County, N. C., on the Avon, Privett property (fig. 1). The deposit outcrops as a vein, or dike averaging-16 to 20 feet in width. Drilling by the Bureau of Mines has shown that this outcrop results from consolidation of a number of small stringers near the surface. The surface width and the Percentage of manganese oxides (resulting from. weathering) diminish with depth. Below 50 to 80 feet, the vein material is mainly quartz and spessartite garnet. The deposit was first examined by W. T. Benson, a Bureau of Mines engineer, in 1941. The Bureau conducted a diamond-drilling exploratory program an the property from November 7, 1944, to January 25, 1945. A. total of 2,508.5 feet was drilled in 14 holes along the strike of the deposit.

Jan 1, 1950

By Robert M. Becker

The evaluation of existing rock stresses from measurements of the change in diameter of a borehole that is stress relieved by overcoring has become a common practice, The stress evaluation has been generally based ,on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium is adapted for evaluation of in situ stress from borehole deformation measurements. A consistent triaxial testing approach for determining elastic properties of the overcore is also outlined. Comparison of isotropic with anisotropic interpretations of the state of stress show that large errors in evaluation may occur if the anisotropic character of the rock is neglected.

Jan 1, 1967

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963

By F. E. Cash

Among petroleum refinery employees and officials throughout the United States there has been marked effort to reduce accident frequency and severity. For the interest and benefit of refineries both in Louisiana and in other petroleum-refining States it has been possible to obtain from five refineries, representing 70 per cent of the production of Louisiana, tae accident experience for the past 3 to 6 years. The companies concerned have requested that their names be not used. For tide reason the four plants listed and discussed are designated as refineries A, E, C, and D. The size of the plant as regards largest to smallest number of employees is indicated by the alphabetical order.

Jan 1, 1933

By B. M. Bird

For several years the U.S. Bureau of Mines and the University of Washington have been cooperating, in a study of coal tabling. The first pert of the work consisted of experiments using, one of the commercial-sized coal washing tables in the laboratories of the College of Mine. As an outgrowth of this work, hindered-settling classification has been successfully applied in the tabling of coal4, and several important improvements, mainly in the riffling, have been made in the table itself. Both of these developments have resulted in increasing the rapacity and efficiency of the coal-washing table. In order to facilitate further progress in this work an investigation has been undertaken to throw more light on the mechanism of table separation. The final separation of a table is obviously the resultant of several operations; namely, stratification, removal of the top strata or parts of them as washed coal by the cross-flowing water, and removal of the bottom strata or parts of

Jan 1, 1929

By R. V. Lundquist

The compound 2Na2O?3CaO?5Al2O3 occurs as a minor phase in lime-soda sinters prepared for extracting aluminum from siliceous aluminum-bearing materials. About 99 percent extraction of sodium and aluminum from synthesized 2Na2O.3CaO.5Al2O3 was obtained in solutions of NaOH-Na2CO3 at leaching temperatures of 50° C and above. Extractions in water were low because insufficient NaOH was generated by hydrolysis. Extractions in NaOH solutions were limited to about 80 percent owing to the precipitation of hydrated calcium aluminates. Rapid extractions of 100 percent were obtainable in NaaC03 solutions, but the subsequent rapid precipitation of alumina trihydrate caused losses in alumina recovery.

Jan 1, 1965

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By Robert E. Barieau

This report describes a method for treating pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. The method makes use of a general nonlinear least-squares technique developed at the Bureau of Mines Helium Research Center. It is assumed that an adequate functional form is available for the expression of the compressibility factor as a function of either the molal density or the pressure. The functional form of the compressibility factor can be either linear or nonlinear in the parameters to be evaluated. Formulas are given for calculating variances and covariances of all parameters evaluated and for calculating the variance of calculated quantities of interest.

Jan 1, 1967

By R. Karl Zipf, Z. T. Bieniawski

"Abstract. Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation.In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions.An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further understanding of the mechanics of fine fragment formation in coal."

Mar 1, 1989