Search Documents

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire f the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By R. E. Morgan

[IN COMPILING the table of analyses of this bulletin every available source of information was studied. These sources, as listed at the end of the table, were many and varied, and it believed that the tabulation gives the best general information obtainable. However, its known accuracy and completeness of coverage necessarily fall far short of published data on coals of the United States. A table of world production of coal and lignite, as and published by the Bureau of Mine, of world resources of coals, brown coal, and lignite, as published in the Yearbook of the World Power Conference, 1948, are included for convenience of the reader. The six continental maps at the end of the bulletin show the general location of the principal coal fields.]

Jan 1, 1952

By Frank J. Wiebelt

The Veta Chica and Cerro Colorado chromite deposits of the McGuffy Creek area, Siskiyou County, Calif. were selected as worthy of investigation by the Bureau of Mines in accordance with the Strategic Minerals Act of 1939. These were two of many chromite deposits examined by engineers of the Bureau of Mines during their extensive wartime mineral examination and exploration campaign. Exploration by the Bureau of Mines consisted of 2,234 feet of diamond drilling, surface trenching, and sampling during the months of May and June 1942.

Jan 1, 1949

By Walter Kawa

The hydrogenation of phenyl ether, benzyl ether, and phenyl sulfide in the presence of iron catalysts was studied by the Bureau of Mines to gain a better understanding of the role of iron catalysts in the hydrogenation of coal. The carbon-oxygen and carbon-sulfur bonds in these compounds may be similar to some of the carbon-oxygen and carbon-sulfur bonds in coal which react during the early stages of liquefaction by hydrogenation. Experiments were made in batch autoclaves for 4 hours; hydrogen was at a pressure of about 540 atmospheres. In the hydrogenation of phenyl ether at 400° C, metallic iron catalyzed both hydrogenolysis (splitting-hydrogenation) and nuclear hydrogenation (addition of hydrogen to aromatic rings) reactions, Products were principally benzene and cyclohexane. The activity of metallic iron was decreased by adding carbon monoxide or a reactive sulfur-containing organic compound. Ferrous sulfide catalyzed the conversion of phenyl ether to benzene, phenol, and small amounts of cyclohexane. Hydrogenolysis of benzyl ether was catalyzed by metallic iron and to a lesser extent, by ferrous sulfide at 250° C. No nuclear hydrogenation was observed with either catalyst. Conversion of phenyl sulfide to benzene was nearly quantitative in experiments made at 250° C with equimolar quantities of phenyl sulfide and metallic iron or iron as ferric oxide. Conversions of metallic iron and ferric oxide to ferrous sulfide were nearly stoichiometric. No reaction of phenyl sulfide occurred in the presence of ferric oxide and water, and very little occurred in the presence of metallic iron and water. Ferrous sulfide also catalyzed the hydrogenolysis of phenyl sulfide to benzene, but conversion was lower than in experiments with metallic iron or ferric oxide. The activity of ferrous sulfide was increased by adding water and decreased by adding hydrogen sulfide. The results of this study suggest that ferrous sulfide is an active form of iron when iron is used as a catalyst for the hydrogenation of coal.

Jan 1, 1963

By A. T. Coumbe, I. F. Avery

The Bureau of Mines has completed a survey of petroleum pipe - lines by direct correspondence with the oil companies and the use of the records of the Interstate Commerce Commission in order to cover both interstate and intrastate systems . The review shows that crude petroleum and product pipe -lines in the United States had a total length of 152,814 miles on January 1 , 1950 , an increase of 25,463 miles since May 1 , 1941 , the time of the last previous survey . The expansion in pipe -line systems was due largely to new trunk-line construction , as the mileage built to carry refined products increased by 11,880 miles , and those intended for crude -oil transportation gained 6,193 miles . Trunk lines represented 60 percent of all pipe -line mileage on January 1 , 1950 , compared with 58 percent in 1941 . The average diameter of trunk -lines for crude oil , as calculated on the various sizes and weighted according to their respective lengths , increased to 9.8 inches on January 1 , 1950 , compared with 8.4 inches on May 1 , 1941. The mileage for lines up to 8 inches used in crude trunklines has decreased since the 1941 survey , while those of larger sizes have increased . The extensive use of large- diameter oil pipe -lines has developed since the construction of two major lines from Texas to the East Coast at government expense as a World War II emergency measure . The successful operation of these lines proved their economic advantages over smallerdiameter lines as well as their effectiveness in moving unprecedented volumes of oil during the period when tanker movements were restricted by submarine action in the Atlantic Ocean . The 24-inch diameter " Big Inch " line carries over 300,000 barrels daily of crude oil , and the 20 -inch " Little Big Inch " carried over 230,000 barrels daily of gasoline and light fuel oils to destinations where they were urgently needed . Hence , Although these lines were sold and converted to natural -gas service in December 1946 , after fulfilling their wartime mission , their record proved to the industry that significantly lower operating and investment costs per barrel -mile of oil moved could be achieved than were possible with the comparatively small lines in general use up to that time . the several major oil pipe -line projects that have been constructed since the late war are of large diameter pipe . To assure supplies and market outlets of sufficient magnitude to support such lines and provide adequate flexibility , ownership is often shared by several large companies whose transport needs are served in common . The principal recent expansion in facilities has been from supply points in Southwestern States toward markets in the North and East and to Gulf tidewater .

Dec 1, 1950

By R. E. Heithecker

The principle of determining volumes of liquid by alternately drawing in and discharging given quantities of the fluid from a confined space or compartment of known volume and mechanically counting the number of displacements is well established. This is true particularly in water measurement. For several years, oil meters employing the same basic principle have beer used for gaging oil production from individual wells, groups of wells, and in some areas for metering the entire production from a property. Especially in areas where there is town-lot drilling and space for tankage is at a premium, oil meters have been used successfully to gale the oil. This facility has obviated the necessity of installing gage tanks. Oil meters also have been used in pipe-line and refinery operations and in loading tankers. Present knowledge e of the subject shows that positive-displacement oil meters can be used for measuring crude oil in the field and elsewhere, provided the meter-counter mechanism is in proper adjustment and the oil has been studied sufficiently to determine the pro-per factor to be applied to the volume as registered by tae meter, possible the adjustment for the shrinkage of the oil caused by liberation of gas from solution.

Jan 1, 1938

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By Kenneth J. Miller

The Federal Bureau of Mines coal-pyrite flotation process has been modi¬fied to produce a concentrated final clean coal slurry underflow that could be dewatered more effectively by filtration or centrifugation. This change was accomplished by redesigning the Bureau's two-stage flotation pilot plant facility and running the second-stage flotation step with undiluted or only partially diluted first stage coal froth concentrate. Results of the pilot plant flotation tests showed that substantial sulfur reduction could be achieved by flotation with undiluted pulp but some dilution is recommended for maximum selectivity. For example, coal-pyrite flotation in slurry of 25 percent solids yielded clean coal products analyzing as low as 0.7 percent pyritic sulfur and froth reject products containing slightly over 3.0 percent pyritic sulfur. In comparison, coal-pyrite flotation with pulp diluted to about 12.5 percent solids yielded clean coal containing as low as 0.4 percent pyritic sulfur and froth reject of 5.6 to 6.7 percent pyritic sulfur. Despite the need for some dilution, it was concluded that excellent coal-¬pyrite flotation selectivity could be achieved without diluting to 6 or 7 per¬cent solids as done in the earlier work. Thus the economics of coal-pyrite flotation would be improved by easing clean coal dewatering problems and by reducing second-stage flotation cell volume requirements.

Jan 1, 1977

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By H. R. Batchelder

The Bureau of Mines Gas Synthesis Demonstration Plant at Louisiana, Mo., includes apparatus for the gasification of pulverized coal with oxygen and superheated steam. A pebble heater constructed by the Babcock & Wilcox Co. is used to superheat nominal 5-pound steam for the gasification process, usually to temperatures of 1,600° to 2,300° F. with flow rates of 1,400 to 2,300 pounds per hour. Heaters of this sort have been described. So far as is known, the Babcock & Wilcox Co. is the sole commercial manufacturer of equipment of this type. Units have been built with capacities above 18,000 pounds of steam per hour.

Jan 1, 1951

By N. Greninger

The Bureau of Mines examined the possibility of a seasonal variation of respirable dust concentration in U.S. coal mines. The first step was to review company and MSHA-inspector dust samples that had been collected during the past several years in 14 selected mines for compliance purposes. Results indicated severe scatter in data; most standard deviations of the dust concentrations measured in winter and summer months were comparable in magnitude with the mean values of dust concentrations for the seasons. Therefore, a detailed statistical analysis was conducted. At the 90% confidence level, the company samples of three mines had winter means 0.15 to 0.54 mg/m3 higher than the summer means; six mines had negligible seasonal variations; and five mines had winter means that ranged from higher to lower than the summer means. Inspector data, however, were too sparse for analysis. In view of both the low frequency of occurrence of a seasonal effect and its wide scatter in several of the mines, the study was ended with the conclusion that seasonal varia-tion in respirable dust levels, in general, is an insignificant factor.

Jan 1, 1986

By S. M. Shelton, F. D. DeVaney, M. M. Fine

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced ; although it is well -known that there are large deposits of low - grade ore in the United States , the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to obtain adequate supplies from foreign sources . Consequently, a program of laboratory and pilot - plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines . This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program . The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series , Report of Investigations 3606 , Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent , and C. H. Schack . Other reports will be published as the work progresses .

Feb 1, 1942

By M. J. Ackerman

This study was undertaken to make a comparison between the cost of mining coal under roof bolt and under conventional timber methods of roof support. Studies were made at 14 mines in Pennsylvania, eastern Ohio, and northern and southern West Virginia. At each mine data were obtained for sections of the mine where the physical conditions, mining equipment, and mining systems were similar. Coal, recognized as one of the basic industrial fuels, is very competitive with other fuels, and management, in order to protect and enlarge its market, must be continually alert to find more efficient methods of production. Continuous production of coal is desired by all operators but never obtained. In mechanized mining the performance and production vary with operating time, which can be interrupted by many variable factors, such as condition of the roof, method of roof support, condition of equipment, water, ventilation, power, transportation, efficiency of operating crew, and supervision.

Jan 1, 1961

By R. P. Vinson

The Bureau of Mines conducted a series of tests to determine how well the Bendix BDX 60, the Gilian HFS 113U, the MSA Fixt-Flo, and the Spectrex PAS-3000 dust sampling pumps control the flow rate at 2 L/min. These tests were performed because users need to know the performance characteristics of sampling pumps to select the pump that best satisfies their sampling requirements. Long-term (6- to 8-h) flow stability at various backpressures was examined in relation to the flow control tolerance of ±5% of the flow, the level imposed by Federal regulations; four of the five Bendix pumps did not meet the criterion for this test, which was passed by all other pumps tested. Flow control recovery times were measured at transient backpressures; all pumps evaluated met the criterion for this test. The low-flow indicators of the sampling pumps were tested; only two Bendix pumps and one Gilian pump met the criterion of indicating a flow change greater than ±5%. In the pulsation flow measurement test all of the pumps passed, with pulsating flows greater than 20 Hz. The Bureau also evaluated the manuals accompanying the sampling pumps. All were judged adequate except the Spectrex manual, which was judged poor.

Jan 1, 1985

By R. V. Ramani, J. Qin, R. A. Jankowski

"Longwall mining is generally recognized as safer, more productive and economic when compared to room and pillar underground coal mining. There has been, however, increasing concern for the control of airborne coal dust concentrations in long wall faces. The airborne dust cloud at a longwall face is a complex aerosol system containing particles of varied size, density, shape and state of aggregation. For the development of more effective dust control practices in longwall faces, it is necessary to understand more clearly the characteristics of the longwall dust cloud.In this paper, results of a research study on dust concentration distributions along longwall faces are presented. The objective of this study is to characterize the longwall dust cloud behaviour and provide necessary fundamental data for a better understanding of the longwall dust problem. MSA personal samplers and gravimetric total dust samplers were employed to collect respirable and total airborne dust samples. The size distribution of these samples was determined by MicroTrac SPA. The instantaneous respirable airborne dust concentrations were recorded using RAM-I. The dust concentrations are related to face operations, particularly the shearer location and activities. The size distribution of airborne dust, instantaneous respirable airborne dust concentration, and air quantity distributions along longw all faces reveal a complex dust flow phenomenon. Additional fundamental studies are needed for characterizing the temporal and spatial behaviour of the dust cloud at longwall faces.IntroductionModern mechanized longwall mining was introduced in the United States in the 1960's and has become more common in the last twenty years. United States longwalls are multiple-entry retreating faces. According to a recent survey, 91 of the 102 longwall faces employ double-drum shearers (1). Several recently installed longwall faces have consistently produced over 4 000 to 5 000 tons per shift over extended periods of operation. The trend in under-ground coal mining in the U.S. certainly is toward the introduction of longwalls. This trend is true not only for new mines but also for renovation of existing mines. While longwall mining has many advantages over other mining methods, including improved safety, such as higher pro-duction. greater productivity and enhanced reserve recov-ery, it is associated with severe problems of dust control. The increase in longwall production has been accompanied by an increase in respirable dust problems which limit realizing the full potential of the longwall mining system. Despite the efforts to develop improved equipment and operational procedures to control the dust levels at longwall faces, it is still difficult to bring several double-drum shearer operations into compliance with the Federal stand¬ards of 2,0 mg/m 3 respirable dust without loss of produc¬tion. In fiscal year 1987, fifty-eight of the longwall sections were found to be in non-compliance once, and an additional 31 were cited two or more times'''. If the full potential of the longwall mining method is to be realized, new measures must be implemented to control the dust concentration to mandated levels. There is a need for detailed and extensive sampling of longwall faces to understand the dust source-sink relationships and the transient ambient concentrations. These must be related to the mining activities on the face. This paper is to characterize the longwall dust cloud behavior through a series of experiments in operating faces and provide necessary fundamental data for further studies to develop improved dust control practices."

Mar 1, 1992

By Thomas J. Peters

The Snowbank study area, which had been proposed as Wilderness, lies about 5 air mi southwest of Cascade, Idaho, and about 60 air mi north of Boise. The eastern boundary of the north-south-elongate study area lies 1-to 2-mi east of Cascade Reservoir; the western boundary is contiguous, in part, with the western boundary of Valley county. The 8,200-acre study area is underlain by Cretaceous granitoid rocks of the Idaho batholith. Three prospects were found in or near the study area during a library and field search. Gold occurs at one 30-ft adit, but the gold-bearing structure appeared too narrow to contain resources. Two other prospects appeared essentially unmineralized. No evidence of geothermal activity was observed. Rock in the area is not potentially useful as dimension stone because it does not split into flat slabs. To be used as aggregate, the rock would require crushing and hauling to distant markets. One of 18 alluvium concentrate (placer) samples contained free gold, worth $1.07 per cubic yard of gravel (at a $350 per oz gold price). No alluvial bars were seen; deposits were too small to contain gold resources or be considered gravel resources.

Jan 1, 1993

By A. L. Engel

High extractions of lead, gold, and silver resulted from treatment of an oxidized, arsenical refractory ore by chloride volatilization. The ore was roasted in an oxidizing atmosphere at 1,000° C. for 1 hour. The chloridizing reagent was 300 pounds of CaC12?2H20 per ton of ore. Ninety-nine percent of the lead, 98 percent of the gold, and 96 percent of the silver, and only 6 percent of the arsenic, were volatilized. These results indicated that a satisfactory method could be developed for treating this type of ore. Recovery and separation of the volatilized values and developing metallurgical and operating data for this process require further investigation on a more extensive scale. Tests by gravity concentration, flotation, and cyanide leaching did not give satisfactory results.

Jan 1, 1958

By Jr. Smith

To investigate the effects of flow geometry on laminar flames, studies are in progress in this laboratory employing Bunsen-type burners with rectangular cross section. Interpretation of these studies requires a determination of the flow velocity at all points of the rectangular cross section for one dimensional steady laminar flow. In addition, values of the velocity gradient at the boundary for such flows are needed in the interpretation of blow-off and flash-back studies with burners of rectangular cross section. The hydrodynamical problem of steady laminar flow of a viscous fluid in channels of rectangular cross section was solved by Stokes. His results have been quoted by Love21 and by Dryden, Murnaghan, and Bateman,§/ and they have been discussed by Boussines and by Paschoud. It may be noted that the steady laminar flow of a viscous fluid in channels of rectangular cross section constitutes a hydrodynamical analogue for the problem of the torsion of an isotropic prism of rectangular cross section.

Jan 1, 1952

By Stanton L. Tainter

"INTRODUCTION Molybdenite, the only common mineral and ore of molybdenum, occurs wide¬-spread but is concentrated as the main ore mineral in commercial quantities in only a few known deposits. Consequently, the Government sought additional sources of the minerals as a precaution against the possible shortage of moylbdenm for war uses. Upon request by the War Production Board, the New Year’s Eve and Esperanza properties of the Amargosa Molybdenum & Copper Corp. were investigated by the Geological Survey 3/ and the bureau of Mines 4/. The Survey appraised the mineral potentialities of the deposit and prepared topographic and geologic maps, and the Bureau made a preliminary engineering examination. The deposits were previously examined by W. J. Vanderwilt, consulting engineer. It was largely due to his recommendations that interest was stimulated in the deposits.Development on the New Year’s Eve deposit indicated a small tonnage of sub marginal ore. There was little development at the Esperanza, but surface examination revealed a large volume of rock containing a little molybdenite and a trace of copper in the oxidized outcrops. Some molybdic oxide was noted suggesting that some molybdenite might have been leached from the oxidized outcrops and that the molybdenite content in the sulfide zone might be higher."

Feb 1, 1947