Search Documents

By F. M. Goodwin, Campbell. John, W. J. Hiffs, G. W. Jones

"INTRODUCTION In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co. a survey has been conducted continuously since 1929 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933.Yearly reports 6 giving the results obtained since the start of the survey have been published.The method and procedure of conductin, the survey in 1935 were the same as heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. N. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner chief engineer, Experiment Stations Division, U. S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing men and information for the work,"

Oct 1, 1936

By C. A. Herbert

This paper sets forth the hazards of accumulations of explosive mixtures of methane and air due to inadequate ventilation, the causes of which are discussed as follows: 1. Lack of well-maintained air courses. 2. Air losses due to leaky stoppings, trap doors, and overcasts. 3. Faulty mining methods. 4. Poor supervision. A modified plan of room-and-pillar panel mine development is suggested, which, it is believed, will eliminate many off the hazards of gas accumulations inherent in the present method of mine development. It is also suggested that some water-proofing agent be used on the roof of permanent air-course entries in conjunction with roof bolting to eliminate the detrimental effect of the moisture-laden atmosphere during summer and thus prevent serious roof falls.

Jan 1, 1953

By W. D. Riley

The Bureau of Mines is conducting research on methods for the rapid identification and sorting of mixed scrap metals and alloys so that domestic scrap resources can be fully utilized. One method, spark testing, is the examination of the pattern of sparks that results when a metal or alloy is ground on an abrasive wheel. This technique requires experienced sorters. Bureau researchers have shown that spectrophotometric methods can be used in lieu of the highly skilled sorter. The spectra of a mild steel, an HSLA steel, several stainless steels, and four nickel-base alloys have been measured. Differences in the spectra that are sufficient for identification are apparent.

Jan 1, 1985

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By Maria I. DeRosa

This Bureau of Mines report describes the Automated Breathing Metabolic Simulator and its hardware and software systems with emphasis on the role exerted by the software program subroutines in controlling the hardware mechanisms during the simulation of man's respiratory and metabolic functions.

Jan 1, 1978

By Gerald V. Gibbs

As a part of the Bureau of Mines long-range program in asbestos, synthetic asbestiform compounds and minerals were prepared and described. Fundamental structural data on two such compounds are given in this report. Crystallographic data are provided for the synthetic isotypic compounds potassium-lead silicate, K2.Pb4 -Si8021 (I), and lead-aluminum silicate, Pb2. Pb4 .Al2Si6O21 (II). The space group symmetry 14/mmm was assigned provisionally to I and II on evidence of single crystal and piezoelectric measurements. A statistical evalua¬tion of indexed powder diffraction data revealed the cell edtes of I to be a 11.816 and c 7.932A and those of II to be a 11.723 and c 8.044A. The phases are uniaxial with observed refractive indices eD 1.790, an ?D,699 and eD 1.884, cusp 1,807, respectively. The atomic structure of I and II may be based on a complex of chains of silicon-oxygen tetrahedra lying along the c cell edge similar to the type of chain structure postulated by Pauling for scapolite. K2.Pb4.Si8021 and Pb2.Pb4 Al2Si6021 were first described by Geller and Bunting (5, 6)4 as fibrous compounds similar in crystal habit to asbestos. These authors gave powder diffraction data, although no attempt was made to find the cell edges or to index the powder diffraction patterns. Later, Shell and others (9) conducted a crystallochemical study of these fibrous silicates in search of a substitute for strategic asbestos. Their single crystal data revealed K2.Pb4 -Si8021 to be tetragonal body-centered with cell edges a 11.66, c 7.95 A. Pb2.Pb4 Al2Si6021 was concluded to be isotypic with K2.Pb4 -Si8021 on the basis of similar powder diffraction patterns, chemistry, and physical properties. No attempt was made, however, to index the powder diffraction record nor to determine the appropriate space group of either compound.

Jan 1, 1962

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By Samuel A. Goldberg

The Federal Coal Mine Health and Safety Act of 1969 delegated to the Bureau of Mines a yearly program of health inspections. Respirable coal mine dust concentrations are measured by Bureau inspectors. Samples of respirable coal mine dust are weighed to determine dust concentration and then analyzed for ash and quartz content. This paper describes the laboratory procedure for determining the percent quartz in the respirable coal mine dust samples.

Jan 1, 1972

By Fred L. Bishop

This paper describing the methods employed in the purchasing and supply departments of the Miami Copper Co., Miami, Ariz., is one of a series being prepared for and published by the United States Bureau of Mines on office practice in mining operations. GENERAL DESCRIPTION The Miami Copper Co.'s plant is located about 1 mile from the town of Miami, in the Globe-Miami Mining District, Gila County, Ariz. The property consists of a complete mining plant, concentrator, high-pressure steam power plant, and many other attendant structures. In normal times the company employs about 1,500 men, and mines and mills about 6,000,000 tons of ore annually.

Jan 1, 1932

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988

By Welton J. Wenger

Apparatus for the analytical distillation of crude oils under an artificial pressure of 760 mm. of mercury has been designed and constructed. This apparatus enables laboratories at high altitudes to make Bureau of Mines routine analyses of crude oils with results similar to those obtained by laboratories at sea level. This is especially important for laboratories in the Rocky Mountain region, where barometric pressures of approximately 600 mm of mercury are encountered. During the past 30 years, the ?Bureau of Mines has made several thousand analyses of crude oils from various parts of the United States and from foreign countries. The first part (stage 1) of the distillation for the analysis is made at atmospheric pressure, and as most petroleum laboratories are near sea level, comparable results are obtained ordinarily. However, the increased use of the method by .laboratories at high altitudes has caused difficulty, as the analyses cannot be accurately compared with analyses from laboratories at sea level. For instance, laboratories at 7,200 feet generally report 2 to&apos; 4 percent (based upon the crude oil) more gasoline than sea level laboratories. The use of the pressurized apparatus developed by the writers makes it possible for these high-altitude laboratories to duplicate analyses made at sea level.

Jan 1, 1949

By M. D. Carver

The purpose of this investigation was to determine the effects of variations in content (near the residual level) of the impurities aluminum, nitrogen, manganese, and copper on the corrosion rate in pressurized hot water and in pressurized steam of zircaloy-3, a zirconium-base alloy of 0.25 percent tin and 0.25 percent iron. Thirty-five 10-pound ingots were cast with the appropriate additions of impurity elements, and these were converted to wrought sheets. These specimens were then tested both in water and in steam. The analysis of the resulting data showed that in environments of either pressurized hot water or superheated steam, corrosion rates increased with increasing content of aluminum, nitrogen, or manganese, but were not affected by variations of copper. The effects of aluminum and nitrogen were found to be greater than the effect of manganese. INTRODUCTION At the request of the Atomic Energy Commission (AEC) in August 1956, the Federal Bureau of Mines, in cooperation with Bettis Plant of Westinghouse Electric Corp., began investigating the effects of certain impurity elements on the corrosion rates of zircaloy-3 in pressurized hot water and in pressurized steam. It was necessary to know these effects in order to set control limits on residual impurity levels in zirnaloy-3, intended for heat transfer service in the nuclear reactor of the pressurized water type. A factorial expert it was designed by Westinghouse statisticians. The Atomic Energy Commission provided raw zirconium sponge purchased from Wah Chang Corp. The Bureau&apos;s laboratory at Albany, Oreg., made material of different combinations of impurity levels and subjected the material to corrosion tests. This report will describe the work done at the Bureau laboratory and will show, quantitatively the effects of different residual levels of aluminum or nitrogen, or manganese or copper on corrosion rates.

Jan 1, 1961

By Frank D. Lamb

"INTRODUCTION The use of beryllium and its alloys has come into prominence in the last 15 years and increased considerably during the war. In contrast to other light metals, such as aluminum and magnesium, beryllium is relatively hard, has a high melting point (1,285° C.), and other properties that make it resemble steel in many respects. It has a specific gravity of 1.85, is only slightly heavier than magnesium (specific gravity 1.74), and is appreciably lighter than aluminum (specific gravity 2.7). Its lack of ductility prevents its use as a structural material, but this difficulty may be overcome in the future by the use of various alloy forms. The only important commercial alloy in which beryllium is used today is with copper. The addition of small percentages (1/2 to 2 percent) of beryllium to copper imparts properties to the alloy that make it desirable for use in springs carrying electrical current, particularly at high temperature. Many other uses of berylliam are known, and new uses are being found constantly that make the metal of increasing interest.Possibly the main factor preventing the use of more beryllium is the lack of a large source of beryllium ore. Many beryllium minerals are found as minor constituents of natural deposits, some of the more common ones being beryl (Be3Al2(Si03)6), chrysoheryl (Be A1204), helvite (3(Mn, Fe) Be Si04. MnS), and phenacite (Be2Si04). Of the known beryllium minerals, beryl is by far the most common and has been found distributed rather widely throughout the world. It usually occurs associated with granitic rocks and is commonly found as a constituent of granitic pegmatite."

Mar 1, 1947

By John A. Burgess

The Carson Hill mine of the Carson Hill Gold Mining Corporation is at Melones, Calaveras County, Calif. It is one of the numerous mines on the Mother Lode of California. The property extends for 8,400 feet along the outcrop of that important vein system. The elevation at the haulage level is about 1,000 feet above sea level. ACKNOWLEDGMENTS Acknowledgment of assistance in the preparation of this paper is made to Frank Wagner, underground superintendent; Max Petersen, engineer; and Homer Mann, assistant engineer. The geology of the Mother Lode has been described by Adolph Knopf in Professional Paper 157 of the United States Geological Survey; references to general geology have been abstracted largely from Knopf.

Jan 1, 1937

By John Jordan, Tesarik, Steven J. Knoll, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

"One of the functions of the United States Bureau of Mines is to investigate the ability of electrical mining equipment to operate in a gassy mine without danger of igniting explosive atmospheres. To accomplish this purpose, tests are made in which mixtures of gas and air are ignited in the equipment while it is surrounded by explosive atmospheres of the same composition. In such tests, records of pressures developed by the internal ex-plosions are obtained and observations are made of any flames, sparks, or smoke which may issue from bearings and joints. Occasionally the explosion pressures in a mining machine rheostat or a compartment of some other machine reach a value which is judged to be excessive or abnormal.A number of factors are known to influence the explosion pressures, and both German and. British investigators have irate extensive research on their effects. Much of this work had been done with artificial compartment which certain conditions could c held, constant while others were being varied. The U. S. Bureau of Mines has not made any research on a scale to compare with that of the British or German investigators; however, special studies have been necessary from time to time to determine the cause and remedy for high pressures obtained in the routine test of some piece of mining machinery. Thus it has been possible to verify some of tee theories established on a purely experimental oasis by practical tests of machines as actually built for mine use.Some of the factors determined the pressure that will result when an explosive mixture in a compartment or connected compartment is ignited are: (1) The volume of explosive mixture ignited, (2) the percentage of as in the mixture, (3) the amount of coal-dust in the compartment or compartments, (4) the degree of movement or turbulence of the mixture at the time of ignition, (6) tightness of the joints and bearings, (6) the size of opening between, compartments, (7) the distance between the point of ignition and openings, and (8) the cooling, effect of surfaces and of material inclosed in the compartments."

Dec 1, 1929

By L. D. Tracy

This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.

Jan 1, 1926

This Bureau of Mines publication presents five papers given at a Technology Transfer Seminar on Metal Mine Fire Protection Research. Several seminars are held each year to bring the latest results of Bureau conducted and sponsored research to the attention of the mining industry as quickly as possible.

Jan 1, 1977

The annual reports of the supervising engineer of the seven sections comprising the Mining Division are assembled in the following pages and form the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By Nick Derick

The continued growth of steel production in the Western States is contingent upon the development of new iron ore sources. Recent development of economical techniques for concentrating and agglomerating taconites has focused attention on the low-grade magnetite deposits near Atlantic City, Wyo., as potentially important sources of iron ore for blast furnace smelting. Therefore, the Federal Bureau of Mines has made comparative evaluations of blast furnace burdens that incorporate pellets produced from Atlantic City concentrates. The Bureau also has evaluated the relative effect of Utah coke on blast furnace performance, using a high-quality Eastern coke as a basis for comparison. This work was done in the Bureau&apos;s experimental blast furnace at Bruceton, Pa. Tests determined the maximum wind rate that could be used while a continuous stock movement was maintained in the furnace. The furnace was operated at wind rates ranging from 800 to 1,400 std. c.f.m., them maximum limit of the blowers for the 1.75 in.-diameter tuyeres used. Using a normal Utah ore burden and Utah coke, the furnace went into a tight hanging condition with a wind rate above 950 std, c.f.m. Using the experimental pellet burden again with Utah coke, the wind rate could be increased to 1,000 std, c.f.m. and probably to 1,050 std. c.f.m, before tight hanging occurs. This represents an increase of 5 to 10 pct. in the wind rate. The experimental results indicate an accompanying increase of iron production, as much as 8 pct.

Jan 1, 1961