Search Documents

By G. A. Brady

Laboratory tests were conducted to determine the technical feasibility of separating anthracite particles from a water-anthracite slurry by atomizing the water and removing the resulting mist in an air current. Products containing 21 percent or less moisture were obtained from slurries made with minus 60-mesh anthracite. Typical recoveries ranged between 67 and 79 percent of the feed when the slurries were atomized in air currents with velocities below 70 ft/min.

Jan 1, 1967

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959

By E. C. Perkins, R. S. Lang, D. M. Taylor, H. Dolezal

The amenability of titaniferous slags and domestic mineral concentrates to chlorination was determined in a 6 - inch diameter fluidized bed chlorinator . Ilmenites from Valley County , Idaho ; Aiken , S.C ,; Trail Ridge , Fla .; and MacIntyre , N.Y .; and a titaniferous magnetite from Iron Mountain , Wyo . , were used in preparing the slags . The domestic minerals tested were an ilmenite concentrate from Valley County , Idaho , and a rutile concentrate from Magnet Cove , Ark . A high - grade Australian rutile was used as a standard for comparison . The impurity content of the slags and minerals tested , which was the most critical factor affecting their performance , was dependent on the geographical source of the material . All of the materials tested were amenable to chlorination in a fluidized bed although some required special operating conditions . Titanium extractions and chlorine utilization were over 90 percent for most of the slags and the Australian rutile . The Valley County , Idaho , ilmenite performed well in the reactor despite its 34 percent iron content .

Jan 1, 1963

By Stephen P. Holt

During the spring and summer of 1946, the Bureau of Mines put down 8 churn-drill holes and 9 diamond-drill holes, totaling 3,535 feet of bore, at the Blewett zinc-lead deposit in Jo Daviess County, Ill. Attention of the Bureau of Mines was first directed to this deposit by the Illinois State Geological Survey, which had investigated the Blewett mine. In the opinion of the Survey and the Bureau of Mines, the record of production and results of drilling previously done on the property were considered sufficient justification for continuing investigation to the north and south along a projection of the trend. This report describes the work done by the Bureau on this, property and presents the data obtained.

Jan 1, 1948

By Jack E. Fraley

Because of their noncombustibility, silicate and magnesium oxycements are desirable for sealing shale in underground coal mines. In this Bureau of Mines investigation, cement samples were cured and tested (nonstandard tests) for submersion to note resistance to dissolution (breaking into parts), which is an important property for a coating. Nonappreciable dissolution during 1 week of submersion was set for passing the test. Over half of the coatings passed the test.

Jan 1, 1977

By Robert K. Koch

The Bureau of Mines investigated separating HF from HF-SiF4-H2O mixtures by passing the mixed gases through a sodium fluoride slurry in an airlift scrubber and forming a mixed precipitate of NaHF2 and Na2SiF6. The oven-dried precipitate was thermally dissociated in two stages. The first stage was carried out at 400° C and dissociated NaHF2 to NaF and HF. Condensation and analysis of the evolved HF proved it to be 97 to 99 weight-percent HF containing 0.79 to 0.99 weight-percent H2O and 10 to 93 ppm silicon. The second stage was carried out at 700° C and dissociated Na2SiF6 to NaF (for recycle) and SiF4. The quantity of HF recovered from gaseous HF-H2O-air mixtures decreased with increasing relative H2O concentrations. Air was beneficial when scrubbing extremely dilute wet HF gases. At HF partial pressures of 0.24 and 0.013 mm Hg in the scrubber entrance gases, HF partial pressures of 6.2 x 10-4 and 9 x 10-6 mm Hg were obtained, respectively, in the scrubber exit gases. Scrubber efficiencies were 99.7 and 99.3 percent.

Jan 1, 1966

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1978 and 1979 was 8831.8 million and $336.4 million, respectively. In 1978, nearly all commodities registered an increase in production and value; unit value increased for all commodities, with the exception of native asphalt and sand and gravel. Alabama led the Nation in the production of crushed marble and was second in bauxite, third in masonry cement, kaolin, native asphalt, and oyster shell, and fourth in bentonite, dimension marble, fire clay, and scrap mica. Trend; and Developments.-The Alabama State Docks at the Port of Mobile handled more than 10 million tons of bulk material in fiscal year 1978; volume dropped slightly to 9.8 million tons in fiscal 1979. Bulk materials comprise the major activity at the facility, with iron ore and bauxite being two of the major materials handled. The movement of these ores is vital to the operation of many heavy industries in the State.

Jan 1, 1981

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By R. L. Brown, H. G. Berger, E. F. Pohlman

"The Bureau of Mines in cooperation with the American Gas Association investigating the relation of properties of gas oils to the gum-forming properties of carbureted water gas. The present report deals with the effects of operating practice on the composition of the light oils from carbureted water gas. A general outline of the gummy meter problem has been presented in a previous paper.*Carbureted water gas is a mixture roughly of 80 per cent water gas by volume and 20 per cent oil gas. The latter, though small in relative volume, supplies more than half of the heating value of the gas under the present-day standard. Therefore, it is logical that the oil used in the carbureting process and the operating practices involved should be subjected to scientific study. Many investigations***** bearing on the aspects considered in this paper have been carried out in the past."

Oct 1, 1923

By D. W. Bridges, R. O. Dannenberg, Laird Crocker

Preliminary solvent extraction studies , reported by the Bureau of Mines (5) , have been continued and expanded to improve on the previous estimate of process requirements . The solvent extraction portion of the process was examined at a scale large enough to enable meaningful extrapolation of the results to geometrically similar equipment of plant size . About 82 pct of the beryllium was recovered from approximately 0.5 pct beryllium oxide (Be0) Spor Mountain , Utah , ore by a process involving ( 1 ) sulfuric acid leaching , ( 2 ) counter current decantation (CCD ) washing , (3 ) iron ( III) reduction by sodium hydrosulfide ( NaHS ) , ( 4 ) beryllium solvent extraction by di - 2- ethylhexyl phosphoric acid ( EHPA) , ( 5 ) caustic stripping of beryllium- bearing EHPA, (6 ) hydrolysis of sodium beryllate - caustic strip liquor , and (7 ) calcination of beryllium hydroxide (Be ( OH ) 2 ) formed in step (6 ) . The resulting beryllia assayed 98 to 99 pct Be0 and was suitable for most nonnuclear uses . Best overall results were obtained by using pH 2 , 1.6 grams of BeO per liter of leach liquor as feed and 0.25 N EHPA in kerosine containing 2 wt vol pct (grams per 100 ml of solution ) isodecanol ( IDA ) as solvent . Analysis of the data indicated that a commercial plant would achieve 95- pct overall extraction operating at 45 ° C with 20 hp per 1,000 gal of dispersion in each of seven mixer- settlers , having 290 gal per ton of ore hourly mixer capacity and 90 gal per ton of ore hourly settler capacity . At least 79 lb H2SO4 , 13 lb sodium hydroxide (NaOH ) , 3 lb NaHS , 0.25 lb kerosine , 0.07 lb polyacrylic flocculant , 0.03 lb EHPA , and 0.007 lb IDA would be required in H2SO4 leaching and subsequent processing to recover 1 lb BeO .

Jan 1, 1964

By Foster Fraas

Under a very high vacuum of 10-8 torr the transfer of terrestrial mineral beneficiation methods to the vacuum ambient of extraterrestrial locations such as the lunar surface was investigated. In the size range for the electro-static and magnetic separation of ores (minus 35 plus 150 mesh) there is no adhesion of particles produced by crushing and grinding due to the limited contact area, and for repeated contacts area size has a frequency of occurrence in accordance to the normal law. The photoelectric effect which is successful in separating a few minerals in an air ambient has a wider application in a vacuum, while the lack of air viscosity and sound transmission provides for high feed velocities and the adaptation of particle vibration to dispersion and grinding. Contact electrification is reversible upon return to atmosphere.

Jan 1, 1970

By Louis A. Panek

An improved centrifugal-testing apparatus has been designed and built in the Bureau of Mines laboratory at College Park, Md., which is unique in that it incorporates the use of resistance gages to measure directly the strains in a rotating model without testing it to failure. Owing to this feature, a more rapid testing method can be used; furthermore, model materials need not be restricted to those of the prototype. The behavior of any structure in which strains of significant magnitude are produced by its own weight may be studied in a small model subjected to simulated gravity loading. The model is rotated in a centrifuge to induce in it centrifugal forces, which, like the gravitational forces in the full-size structure, act on the volume elements and are proportional to the masses thereof. Centrifugal testing is, therefore, applicable to the design of mine openings and to the study of similar ground-control problems. It constitutes an experimental method for determining the state of strain in a structure for which analytical methods are excessively laborious or even impossible. In previous applications of centrifugal testing by other investigators, the models usually were tested to failure, and the analysis was made from-the type of break produced. The models were made of the same materials as the proto-type, and the test results were applied only to the particular prototype represented by the model. Beam deflections were measured from photographs of the rotating model, but no means was employed either to determine the actual distribution of stress in the model or to determine quantitatively the degree of restraint imposed on the ends of the loaded model beam, that is, to determine whether the loaded model behaved as a beam with rigidly fixed ends or as some other type of beam. With the apparatus described, it is possible to determine the state of strain, and thus the boundary conditions, in a rotating test model weighing up to 90 lb., which can be subjected to centrifugal forces up to about 2,600 times the force of gravity. The load-strain relationship, applicable directly to the prototype, can be determined from a Single model test. The test results can be presented as quantitative relations between the loads, strains, and dimensions and mechanical proper-ties of the structural members and can be applied to any prototype, whatever its component materials, that satisfies the similarity requirements.

Jan 1, 1952

By R. V. Higgins

A computer program is presented to calculate the shape factors and volumes of cells from a potentiometric model, using coordinates of the inter-sections of the stream lines and equal potentials and a few additional coordinates. Shape factors are used in flow computations when the geometry is complicated. The program also includes computer instructions to divide the channels into cells of equal volume and to obtain the shape factor for each of these equal volume cells. An illustrated example using the potentiometric model for the waterflood of a seven-spot well-spacing pattern is presented. The information contained in the report is of value not only to those allied to the subject but also to others, because many of the techniques can be conveniently used in formulating other computer programs.

Jan 1, 1966

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking in the past few years have focused the attention of the Bureau of Mines on the need for safety standards for such operations. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1957

By M. M. Fine

"Button" type ore from the Cason mine, Batesville, Ark., can be up-graded to plus-40-percent manganese by mineral-dressing procedures. A simple process including gravity concentration and. magnetic separation yielded more than 50-percent recovery of concentrates containing 38.1 to 40.6 percent manganese. These values in turn could be raised to 41.4 and 42.8 percent, respectively, upon sintering to conform to size specifications. The Bureau of Mines in the past has surveyed and tested many manganese ores and prospects in an endeavor to alleviate the shortage of manganese. The present period of emergency again emphasizes the strategic position of the metal, and manganese investigative work is being stressed to find new ore bodies and to apply newer beneficiation techniques to the known deposits.

Jan 1, 1953

By R. F. Abernethy

A small-scale method was developed for determining the free-swelling index of coal samples of limited quantity, especially the macerals. Results of a series of tests using a 0.3-gram sample correlated well with those by the standard method using a 1-gram sample. The standard and small-scale methods are modified to give unrestricted swelling for those coals having swelling index numbers above 7.

Jan 1, 1971

By Arden D. Fugate

This work was conducted to determine a feasible process for converting siliceous fluoride offgases to a commercially usable product. The offgases were generated by pyrohydrolytic defluorination of low-grade fluorspar in a gas-fired rotary kiln, and fluorine was collected as a hydrofluoric-fluosilicic acid. A silicon-free fluoride solution for further processing was then produced by neutralizing the acidic scrubber solution with anhydrous ammonia, silicon being separated as orthosilicic acid. Ninety to ninety-nine percent of the fluorine originally present remained in solution as ammonium fluoride. Silicon was also separated from synthetic fluosilicic acids, having F-to-Si weight ratios ranging from 3.50 to 14.3. The solutions below a ratio of 4.06, the F-to-Si ratio of H2SiF6, containing dissolved silicon were desiliconized as completely as those containing less than the stoichiometric quantity of silicon. An electrolytic-grade cryolite was recovered from the ammonium fluoride solution by reacting with either sodium aluminate or alumina trihydrate and sodium hydroxide. A product containing 97 to 100 percent of the fluorine, represented by Na3A1F6, was recovered, and 94 to 99 percent of the theoretical yield was realized.

Jan 1, 1963

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

[1.1. The provisions of this code are minimum provisions and are designed to minimize hazards to life and property in and about underground coal mines where electrical equipment and circuits installed used. They indicate the Steps necessary in the selection, installation, operation, inspection, and maintenance of electrical equipment and circuits to obtain proper safeguards in reducing electric shock, fire, explosion and other hazards. Surface as well as underground installations were considered in formulating the code and, unless otherwise stated, each provision applies equal to both underground and surface installations. This code does not apply to buildings and installations not directly connected with mining operations, nor does apply to strip-mining operations.]

Jan 1, 1952