Search Documents

By P. G. Guest

Many of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed, in operating and anesthetizing areas. When ether was first introduced, candles and gas-lights and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions -many of them fatal to patients -have been attributed, with good reason, to sparks from static electricity. In this paper the authors present facts to show the prevalence of static electricity in the average hospital anesthetizing area, and the degree to which this easily developed electrical form of energy constitutes an explosion hazard. An effort is made throughout to explain how static electricity behaves, why it is a hazard, and why certain safety measures are needed and recommended. Following the introduction and a short general discussion of static electricity, which incorporates a glossary of pertinent electrical terms, an account is given of inspections and tests made in a number of hospitals. This account includes many suggestions that should be useful to any person who plans to make similar inspections and tests. However, a comparison of materials and equipment used with those described in the report will reveal, in many cases, the potential dangers and obviate the necessity for tests. The hospital work was supplemented by considerable laboratory research designed to determine the spark energies required to ignite anesthetic-gas mixtures and the exact amount of time involved in developing the usual static charges. The results of this research are reported and the implications examined. The paper concludes with a general discussion of static and related hazards in anesthetizing areas and of the most urgent preventative measures.

Jan 1, 1952

By C. Özgen Karacan

Gamma ray, density, sonic and core logs obtained from two boreholes drilled over a longwall panel in Southwestern (SW) Pennsylvania were analyzed for formation boundaries, log-derived porosities and densities and for rock elastic properties from sonic transit times. Gamma ray (GR) and density logs (DL) were analyzed using univariate statistical techniques and fractal statistics for similarity and ordering of the log data in depth. A Fourier transformation with low-pass filter was used as a noise elimination (filtering) technique from the original logs. Filtered data was tested using basic univariate and fractal statistics, rescaled range (R/S) and power spectrum (PS) analysis to compare the information characteristics of the filtered logs with the original data. The randomness of log data in depth was analyzed for fractional Gaussian noise (fGn) or fractional Brownian motion (fBm) character. A new prediction technique using radial basis function (RBF) networks was developed to calculate shear and Young?s moduli of the formations when sonic logs are not available. For this approach, the filtered logs were used as input to an RBF based upon a combination of supervised and unsupervised learning. The network was trained and tested using rock elastic properties calculated from the sonic log of one of the boreholes. The network was used to predict the elastic and shear moduli of the coal-measure rocks over a longwall coal mine in SW Pennsylvania. This approach demonstrated that it could be used for prediction of elastic and shear moduli of coal-measure rocks with reasonable accuracy.

Jan 1, 2009

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources -limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to deter-mine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources - limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite, The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By T. E. Gray

This report describes preparation characteristics of the significant coalbeds in Marion County, W. Va., as determined by the Bureau of Mines. It is one in a series telling what coals are suitable for producing metallurgical coke, either as mined or after beneficiation. Over 9.4 million tons of coal was produced in Marion County, W. Va., in 1958, of which almost 6 million tons was cleaned mechanically in nine cleaning plants. All of the coal mechanically cleaned came from the Pittsburgh bed. The Bureau of Mines estimated that 1,578 million tons of recoverable coal remained in the county in beds 28 inches or more thick as of January 1, 1955.

Jan 1, 1960

By Edwin S. Secor

The Federal Bureau of Mines conducted a field survey of 153 bituminous coal strip and auger mines to estimate coal recovery from surface mines in the Eastern United States. Recovery was calculated from field data by measuring coal losses resulting from mining coal and leaving barriers. Mean total recovery for strip mining in States east of the Mississippi River was 83.0 percent and ranged from 72.3 percent for Tennessee to 91.3 percent for Maryland. Mining losses and barrier losses were 10.1 and 7.7 percent, with standard deviations of 4.8 and 10.4 percent, respectively, indicating that barrier losses, although less than mining losses, were more variable. Mean total coal recovery varied only slightly for the two regions studied; 82.7 percent for Appalachia and 84.3 for the Midwest. Total recovery grouped by mining method--contour, area, and mountaintop removal--was 79.8,84.7, and 85.3 percent, respectively. Mean auger recovery was 35.9 percent; of the total average loss of 64.1 percent, over one-half resulted from design limitations while the remainder was attributed to operating losses. The wide recovery range at individual mines indicates the variability of the eastern surface coal mining industry. Because of this, care should be exercised in applying the results of this report to reserve estimates other than those of a general nature.

Jan 1, 1977

By R. E. Collom

The spontaneous explosion of charges of nitroglycerin placed in deep wells situated in parts of the Ranger and Caddo fields of North Texas has aroused considerable inquiry among operators end others as to the probable agency, or combination of conditions, which causes the explosion.The method now followed, under certain physical conditions of a well, of setting a charge of nitroglycerin and allowing it to explode spontaneously was discovered locally by accident. In certain deep wells where formations, overlying productive strata, cave upon withdrawal of casing, it has been the practice to fire the shot electrically. In some of these operations the electric wires are broken or the firing system is otherwise deranged by pulling casing or the caving of hole prior to the time for firing. Sucn accidents make it necessary for the driller carefully to clean cavings out of the hole to a depth close to the top of the charge, after which in the normal practice, an attempt is made to fire the charge by dropping a ""jack-squib"", fitted with a fuse and detonator, down the well. Mr. R. L, Fowler, production manager for the Pierce Oil Corporation, reports that a delayed shot was thus successfully tired through four feet of caved material lying on top of the nitroglycerin shells.When a shot destined to be fired electrically fails, because of the above mentioned accidental conditions to the electric firing system, much time is required for the driller to run casing into the hole and clean out caved material. It was during the time of such uncompleted operations that the spontaneous explosions first noted took place. Having noted these spontaneous explosions the well shooters now intentionally place a charge in deep holes, which because of probable caves would otherwise have to be tired electrically, and wait for the charge to go off. No detonators are placed with the charge.

May 1, 1920

By Rolland L. Blake

Petrographic and mineralogical studies were made on unoxidized samples from the Cuyuna and Mesabi districts to study occurrence and properties of the iron phyllosilicate minerals . Examination of 96 thin sections from the thinbedded facies of the main iron - formation of the Cuyuna district indicates that the most abundant minerals are Mn - Mg - siderite , stilpnome lane , and minnesotaite . Reconstitution and recrystallization of minerals has occurred along certain beds , and textures indicate that some minnesotaite apparently formed at expense of stilpnomelane . Three samples of stilpnome lane and one of minnesotaite were concentrated from fracture - fillings within iron- formation . Results of chemical , optical , spectrographic , X- ray diffraction , and differential thermal analyses on these samples are reported . The detection of ammonia in stilpnome lane samples is the first such occurrence reported , and its significance is discussed . New mineral data are presented on greenalite and probable septechamosite from the Mesabi district .

Jan 1, 1964

By Donald F. Reed

The bauxite deposits of Tippah and Benton Counties in northeastern Mississippi were developed by drilling as a part of the investigation by the Bureau of Mines of the domestic sources of supply of aluminum. The primary purpose of investigations of this nature was to provide essential information to the war agencies of the United States Government and to assist owners and operators of mining properties in the production of minerals vital to the prosecution of the war. These reports are based upon the field work of the Bureau of Mines and upon data made available to the Department from other

Jan 1, 1948

By Arnold C. Love

This report discusses current research by the U.S. Bureau of Mines on the effects of whole-body vibration (WBV) and shock on underground mobile equipment operators. The highlights of a comprehensive literature review of WBV, shock, and seating are presented. Factors discussed include health and physiological effects, comfort, performance, and fatigue. Vibration data were collected from shuttle cars and ramcars at several underground coal mines in Pennsylvania, Ohio, and Illinois. The data were formatted so that they could be used to drive the Bureau's motion platform, and to compare them with ANSI S3-1979, Guide for the Evaluation of Human Exposure to Whole-Body Vibration. Human subject testing in the Bureau's vibration research laboratory evaluated the effects of two different seat angles and of the presence or absence of vibration and of foam padding on heart rate, blood pressure, and subjective discomfort. Only vibration significantly increased heart rate and systolic and mean blood pressures. Vibration and a steel seat had a significant effect on subjective discomfort. The apparatus used for these tests and the experimental procedures are described in detail. Recommendations are made for additional research on the exposure of underground mining machine operators to WBV and shock.

Jan 1, 2010

By R. S. Warfield

The Kasna Creek copper deposit near Lake Kontrashibuna in the Lake Clark region, Alaska, was the object of an investigative project by the Bureau of Mines during the fall of 1948. Recessed because of inclement weather, it was completed in 1949. This project was a part of the Bureau of Mines program in Alaska for the development of critical and strategic minerals. The ore bodies are contact-replacement deposits in limestone. Mineralization is mainly specular and micaceous hematite associated with chalcopyrite, calcite, chlorite, quartz, and amphibole. The deposit, on the right limit of Kasna Creek approximately 2 miles from the shore of Lake Kontrashibuna, is composed of two mineralized zones that range in altitude from 2,350 to 2,650 feet. This report contains a brief history of the prospect, description of the physical setting of the property, its geology, and the factual results of the Work performed by the Bureau of Mines.

Jan 1, 1951

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

This report describes serious injuries occurring to bulldozer operators working at U.S. coal, metal, and nonmetal mines. The period covered is 1988-97. The data were collected by the Mine Safety and Health Administration (MSHA). A total of 873 injury records are examined. These injuries resulted in 18 fatalities and 31,866 lost workdays. All of these injuries occurred to dozer operators while they were doing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Injury records are categorized by activity (task being done), incident result (what apparently happened to the dozer), and operator impact (how the operator was injured). Where information is available, contributing factors are identified. This classification system supplemented the standard injury/illness data classification system compiled by MSHA. The results of the study indicate that, from 1993 to 1997, the number of serious injuries to dozer operators declined by 30%. The reduction in serious injuries was accompanied by a decrease in days lost due to injury. Although the number of reported injuries has decreased, dozer operators being jolted and jarred accounts for the largest percentage (70% of the incidents) and severity (75% of the workdays lost) of serious injuries while operating the equipment. Vertical jars (while backing up the dozer) resulting in injury to the operator accounted for a sizable percentage of jolting and jarring injuries. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over, or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fall over or rollover, 7 out of 26 were killed. Overall, 80% of the fatalities occurred while working near an edge or hidden void or on a steep slope. Further reductions in injury risk will require more widespread use of seatbelts, field and laboratory research interventions to better assess the effect of alternative engineering (e.g., seat and seat suspension) designs to dampen or isolate the effects of shock and vibration, and continued focus on hazard awareness, recognition, and response.

Jan 4, 2001

By Robert M. Becker

Part 5, the last of this series, deals with the theoretical confirmation and application of results developed in parts 1 and 2. The bulk-sampling variances of Hassialis and Kassel and Guy are compared with those in part 2, both as to formulation and as applied to ores and coal. The results provide confirmation for much of the development in part 2. Examples are presented for determining the reliability of bulk samples with respect to various measurable characteristics. These characteristics include, for example, assays for elements or compounds and particle surface area. The bulk samples considered consist either of a given weight, a given volume, or a given number of particles. In addition to problems of sample reliability, some of these examples may also be applicable to quality control. Several possible applications of results developed in parts 1 and 2 are outlined. These include tests for random data, degree-of-mixing indices, and particle-fineness indices.

Jan 1, 1966

By D. A. Paice

A portable calibrator to check tie trip setting of dc circuit breakers within an accuracy of +5% has been developed for the Bureau of Mines. It operates from a 300 volt dc trolley wire to provide controlled current pulses of 120 milliseconds duration and continuously adjustable from 1400 to 3600 A. These current pulses enable a breaker dc trip current to be determined and subject the contacts to full current rating. The equipment is simple to use and weighs 86 pounds. Connections are made with protected, clamp-on leads which are separately connected and weigh about 22 pounds. An accurate calibration procedure takes less than 5 minutes to complete.

Jan 1, 1978

By Kenneth L. Cashdollar

This report describes three types of optical dust probes that have been designed, built, and tested by the Bureau of Mines. Each of the probes measures dust cloud concentrations by the attentuation of light. The first is a single-path-length probe, the second is a double-path-length probe, and the third is a single-path-length probe that employs jets of air to keep the windows of the light source and detector free from dust coating. The theory of operation and the calibration procedures for each of the probes are described. The results of the Bureaus laboratory, mine, and field tests of the probes are also reported.

Jan 1, 1981

By J. F. Barkley

At the request of several Federal agencies, tests were conducted on a relatively recent type of anthracite -burning equipment named the Anthratube. This device, rated at 130,000 B.t .u. per hour, was designed to burn Pea-size anthracite automatically for steam or hot-water house heating and for domes-tic hot -water supply. ACKNOWLEDGMENTS The helpful cooperation of the Anthracite Institute and the manufacturers of the equipment, Axeman-Anderson Co., Williamsport, Pa., is gratefully acknowledged.

Jan 1, 1953

By H. B. Humphrey, F. E. Cash

The Southern Appalachian coal field extends southward across Tennessee in a belt about 50 miles wide between the eastern and middle sections of the State. The earliest record of the production of coal in Tennessee is for 1840, and the first inspection laws were passed in 1881. In 1887, a second act of the legislature created the office of Chief Inspector, but little was done until 1891 when a new act was passed giving to the Department of Mines added duties and powers. Since that time, except for the years 1915 to 1918, com¬ prehensive annual reports have been published. Data for the tables given in this paper are taken from these annual reports, from those of the Southern Appalachian Coal Operators' Association, and from the publications of the United States Bureau of Mines, which has main¬ tained a station at Jellico, Tenn., since 1911. Complete figures for 1930 are not available yet and they are not included in the averages. The State Department of Mines, the operating companies, and the United States Bureau of Mines cooperate in accident-prevention work. It is the purpose of this report to present in uniform tables the available statistics in regard to fatal accidents in Tennessee and in the coal mines of the United States, in order that the progress in mine safety in Tennessee may be compared with that of the country as a whole, and the present period may be compared with various periods of the past, to indicate the main points of attack in the reduction of accidents.

Sep 1, 1931

By C. E. Wyndham

The occurrences of manganese In Alabama were reported to be widely scattered over the northeastern section of the State, and these were examined before a development project was started.2/ The most promising and available showings were chosen for further investigation, which include 1 deposit in Goshen Valley, 6 in the Rock Run area, and 2 in the northern section of Calhoun County. The work was performed by the Bureau of Mines from July 29, 1949, to February 17, 1950. The work consisted of power auger drilling 69 holes 3-1/2 inches in diameter and totaling 2,548.4 linear feet. The accuracy of samples from auger drill holes in this type of deposit was determined by sinking two shafts a total depth of 68.17 feet, from which channel samples were cut. Sixteen rotary core holes totaling 1,048.7 linear feet were drilled with a 3-inch, double-tube core barrel. Twenty-two diamond core holes were drilled with a 2-1/8-inch, double-tube core barrel and NX diamond bit. In addition to the above drilling 220.8 cubic yards of soil and rock was excavated by hand from 403.9 linear feet of trenches and 69.7 feet of test pita. A total of 206 samples were taken and analyzed for manganese, iron, cobalt, nickel, and insoluble.

Jan 1, 1953