Search Documents

By K. R. Dorman

To develop the potential of precast concrete sets as a support medium in underground mines, a three-piece precast concrete drift set was designed for a small opening and tested to destruction in an underground straining frame. Thirty-six tests were made with three sizes of members using three different loading conditions. In addition, 14 members were tested individually in the laboratory. Test results are compared with theoretical calculations. A cost comparison shows the use of concrete sets would be advantageous where conventional wooden timber requires excessive replacement.

Jan 1, 1968

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964

By Charles E. Semler

The possible utility of selected compositions in the systems SrO-ZrO2-MgO and SrO-ZrO2-Dolomite for commercial refractory products was confirmed in this study. Specifically the compositions of interest are located in the sub-systems SrZrO3-ZrO2-MgO and SrZrO3-ZrO2-Dolomite. Both sub-systems have regions that are not affected by hydration, but the sub-system SrZrO3-ZrO2-MgO has a larger candidate compositional region. Solid state phase relations were determined for the subject systems over the temperature range 1600°C to 1300°C, with compatibility diagrams presented for each. The systems appear to show good refractory character with no apparent low melting compositions. As the compositions of commercial interest lie mostly in the higher ZrO2 portion of each system, information is presented regarding the firing treatment required to develop stabilized cubic ZrO2. A list of suggestions for further study of these systems, to further delineate the characteristics required for possible commercial utilization, is presented.

Jan 1, 1982

By Paul R. Thomas

The Bureau of Mines evaluated the impact of the depletion allowance upon the economic availability of copper from domestic deposits. The potential long-run percentage depletion deduction, cumulated over the life of the properties, was estimated at approximately $2.5 billion for producing properties and up to $11.7 billion for nonproducers. The income transfer, in the form of higher Federal income tax payments if the allowance were repealed, was estimated at $1.5 billion for producing properties and up to $8 billion for nonproducers. The percentage depletion allowance, through its role in determining Federal income tax liability, was found to be very significant in affecting profitability. Repeal of the allowance could result in major domestic copper availability reductions at all price levels, now and in the future, as a result of reduced profit margins for current producers, and postponement of development decisions for nonproducers. It was demonstrated that a 50-percent reduction in the percentage depletion rate applicable to copper would also result in a significant decrease in profitability for nonproducing properties. For producing properties, the percentage depletion rate on copper was shown to be less significant than the income limitation that is placed upon the total amount of the depletion deduction. Repeal of the minimum Federal tax provision was shown to be significant in enhancing profitability for both producing and nonproducing deposits. The report concludes that the percentage depletion allowance operates as an important method of capital recovery and production incentive.

Jan 1, 1982

By BUREAU OF MINES

This report is submitted in accordance with the provisions or une Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1951 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: Oil from Coal. R. I. 4865, Part I - R. I. 4866, Part II - Oil from Oil Shale. Identical in each report, the introduction summarizes research progress made in 1951 under the entire Synthetic Liquid Fuels program. A free copy of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Jul 1, 1952

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By V. F. Parry

This report is the first substantial description of the carbonizing process and the details of experimental work conducted at the Denver laboratories under a coopeative agreement between the Bureau of Mines and the Texas Power & Light Co. It presents the results of tests on several Texas lignites and other typical western coals that have been processed in the first pilot plant operated at Denver. Investigations on drying fine coal in the entrained and fluidized state have been under way at Bureau of Mines Denver laboratories for several years. Reports on this work were published in 1949 and 19505/ describing the theory and practice of re-moving inherent moisture from the lower -rank coals. The investigation did not include a study of the removal of surface moisture from fine fuel. Private industry in Canada became interested in the possibilities of drying fine coal, employing the closed-circuit system and techniques recommended by the Bureau. Large, commercial-scale drying units were built by a Canadian company, which successfully demonstrated that surface moisture could be removed from fine coal at high efficiency and capacity ill drying units similar in design to those developed by the Bureau.

Jan 1, 1953

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened in scope, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and non-metallic mines. These circulars are as follows: Injury Statistics (Miners' Circular 51), dealing with general statistics on injuries from accidents at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all injuries.

Jan 1, 1960

By Carl H. Beal

The oil industry in the United States is further advanced than in any other country, because of American initiative and the development of industries dependent in some way on petroleum or its products. For this reason the output has constantly increased (fig. 1), and as a result this country has produced more than half of the total output of the world. Trw total past output of the world is approximately 7,000,000,000 barrels of 42 gallons each; of this the United States produced about 4,000,000,000 barrels, or about 57 per cent. The limit of production in this country is being approached, however, and although new fields undoubtedly await discovery, the yearly outpnt must inevitably decline, because the maintenance of a given output each year necessitates the drilling of an increasing number of wells. Such an increase becomes impossible after a certain point is reached, not only because of a lack of acreage to be drilled, but because of the great number of wells that will ultimately have to be drilled. According to figure 1, the daily production per well each year has increased during the last few years. However, this increase is abnormal, being caused by the new pools brought in. Although such a condition may continue for several years, the average production per well will finally begin to decrease on account of the lack of new pools to make up for the normal decline in production of the old ones.

Jan 1, 1919

By John D. Spencer

Research on the development of new and improved methods for the discovery and production of oil and gas and production of fluid fuels from coal continued to be the major thrust of the Bureau of Mines energy research program during 1973. Crude oil recovery from tar sands and oil shale also retained a high priority in this work. Complementing this program were numerous studies aimed at accomplishing the objective of increased energy output with greater safety and minimum harm to the natural environment. This report summarizes research objectives and results and itemizes formal publications of the Bureau of Mines on energy and related subjects.

Jan 1, 1974

By Norman L. Wimmler

Active placer mining in Alaska began near Juneau in 1880, but the first gold rush did not start until 1896; then the discovery of the Klondike brought gold seekers from all parts of the world. A few of the newcomers were experienced miners, but the majority knew nothing whatever of placer mining. Even those who were placer miners of much experience found entirely new conditions, notably frozen ground, that presented many difficult problems. As a result, numerous methods of mining and of thawing frozen ground were tried. From these trials the practice described in this bulletin has been developed. All known placer fields in Alaska have been mined to some extent, and some have been virtually exhausted. In most districts, however, there remain large quantities of low-grade gravel and also some small isolated areas of comparatively rich gravels which could not be successfully mined because of adverse physical conditions. These districts are now the scene of most placer mining, including dredging, hydraulicking, drifting, mechanical methods of open-cut mining, and ground sluicing (or booming) followed by " shoveling-in."

Jan 1, 1927

Maps To Accompany Bulletin 418

Jan 1, 1941

By C. T. Sheeran

The Bureau of Mines investigated a microprocessor-based real-time control and monitoring system for uranium mining applications. The system is capable of controlling and monitoring up to 768 stations within 3 km of the central processor on a common four-wire cable. It can be used in conjunction with detectors to continuously monitor and display radiation working levels at points throughout the mine. Surface alarms are sounded for critical situations such as rapid radiation buildup, loss of power to monitors or fans, and changes in air door position. Permanent records of all changes are automatically printed out with their time of occurrence. Printouts can also be obtained for shift reports or trend logs. The system can be used to remotely control fan startup and shut-down, and also can alert miners of underground conditions by blowing horns or turning on lights. Battery backup keeps the system operative for up to 4 h in case of a mine power outage. A special software feature permits automatic, time-delayed, sequential restart of fans.

Jan 1, 1984

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California in 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemica 1 manufacturing; a shift in requirements from metals to nonmeta ls, from inorganics to organics, from natura 1 to synthet ic materia ls , and from distant to local sources of supply.

Jan 1, 1965

By John E. Miller

Supercompressibility factors, Fpv, were derived from experimental compressibility data for five helium-nitrogen mixtures containing from 50 to 100 pct helium. These Fpv values are required as volumetric correction factors for or if ice meter measurement of "crude helium" (helium-nitrogen) purchased by the Government in a program of helium conservation. Although compressibility measurements were made by the Burnett method (2)3 - for pressures from 100 to 3,400 psia and temperatures from 40° to 100° F, Fpv values were needed only for pressures from 400 to 2,000 psia. Consequently, values at increments of 2° F, 2 pct helium, and 10 psia were tabulated only for the required pressure range. Values for pressures outside this range can be calculated from information shown in the tables. Values for the second, third, and fourth coefficients in the equation Z = 1 + BP + CP2 + DP3 are also included.

Jan 1, 1963

By F. W. Horton

Investigation of an extensive deposit of chromite-bearing actinolite-talc schist situated on the summit of Casper Mountain, 10 miles south of Casper, Wyo., was one of the first projects Undertaken by the Bureau of Mines under the Strategic Materials Act (Public 117, 76th Cong., Ch. 190, 1st sess.), for which an appropriation became available August 9, 1939. During the previous summer; the Geological Survey? made? a magnetometrical survey of the area in which the schist occurred. It was exposed in several small lenses and two larger ones aggregating about 19?acres in area. Although the occurrence of chromite here had been known for many years, the only work done on the deposit was the digging of? a few shallow pits on some of the more promising outcrops. From August 23 to December 3, 1939, the Bureau of Mines investigated the larger of the two main schist bodies. Twenty-four trenches having a total length of 8,073 feet were dug across the deposit, and its subsurface extension was explored by 3,623 feet of diamond drilling. Over 32 tons of samples were shipped to the Metallurgical Division of the Bureau of Mines at Reno, Nev., for reduction, analysis, and ore testing. In all, there were 853 individual samples. Geological maps, based upon examination of outcrops, trenches, and drill cores, as well as a contour map of the area were made by the Geological Survey.

Jan 1, 1949

? CAGER, CAGE RIDER, CAGE TENDER, SHAFT MEN All of the above job titles are variously associated with the handling of men and material at hoist stations. Generally, these classifications of personnel are involved with riding cages with personnel and in hoisting supplies into the mine. Job titles and activity description will be defined in the respective chapters. ? FLOW CHART SYMBOLS [Vertical Transportation Horizontal Transportation Storage Operation Delay ]

Jan 1, 1975

By E. H. Denny

This paper discusses accident experience and costs in 150 Colorado coal mines for the 5 years 1929-33; these mines produced 62 percent of Colorado's coal tonnage during this period. This and similar studies by the United states Bureau of Mines in other States (listed in the appendix to this report) make available comparable information on mine-accident costs and bring out clearly the importance of accident reduction from the humanitarian as well as from the economic standpoint. Compensation insurance costs constitute a considerable part of the cost of coal output. The tendency toward greater liberalization of workmen's compensation laws and increased benefits thereunder may mitigate to some extent the seriousness of an accident to a worker and his dependents, but no compensation is paid ultimately, not by an insurance fund but by the mine operator and the general public, which includes the miner. The one really effective method of reducing compensation costs is to reduce the number and severity of accidents.

Jan 1, 1935