Search Documents

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Joshua Hoffman, Catherine Johnson, Braden Lusk

Blasting conducted in surface coal mining operations in the Appalachian region consumes a significant amount of blasting agents. Emission of oxides of nitrogen (NOx) from these operations potentially represents an environmental challenge. This paper presents work conducted to quantify NOx output from the detonation of blasting agents common to surface blasting operations in surface coal mines. Annual ANFO and emulsion consumption data was collected from an operational surface coal mine located in West Virginia. It is known that many factors contribute to the types of gaseous byproducts released from the detonation of explosives. These factors include but are not limited to: fuel to oxygenator ratio, degree of confinement, and contamination. While, past research has been conducted to study the relationships these factors play on the release of NOx, these findings do not agree with one another. The annual explosive consumption values from the West Virginian mine were applied to NOx emission conversion factors in published literature. This lead to a range of NOx emissions from 95 to 914 tons in a year. Given the wide range of NOx production the utility of this information is suspect. The EPA recognizes a standard factor of 17 lbs (NOx)/ton (ANFO) however this factor is based on chemical composition and does not address contamination, confinement, or AN to FO ratio. This factor when applied to the West Virginia Mine's explosive consumption produced a value of 215 tons of NOx. There is a lack of information on NOx emission from emulsion type explosives. The work presented in this paper can be used by blasting professionals to quantify NOx emissions and guide future work for producing better predictor factors.

Jan 1, 2014

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998

By Dale S. Preece, Vanessa S. Berg

Shaped charges are being utilized in defense applications against a wider variety of targets including concrete, rock, and soil. This work was motivated by a heightened interest in characterizing the effect of shaped charge attack on brittle, non-homogenous materials, in particular, concrete damage and penetration predictions resulting from a TOW-2a conical shaped charge (CSC). This paper presents a multi-stage approach for accurately predicting the high explosive detonation and subsequent jet formation due to the collapse of shaped charge liner, the changes in jet length and diameter as a function of standoff distance, and the jet-target impact dynamics. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN to predict the shaped charge jet formation. 2-D finite difference Eulerian subgrids represent the explosive and casings components, while thin components like the liner are modeled with Shell subgrids. The Pugh, Eichelberger & Rostoker (PER) jetting theory option is invoked to obtain the jet and slug masses and associated velocities. The jetting data is post processed where the jet velocity gradient and jet mass is used to solve for the new jet length and diameter gradient at a desired standoff. The final computation involves a 2-D fully Lagrangian model in which the jet and velocity gradient is represented by a string of Lagrangian segments and the concrete target is defined as Lagrangian with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model. This model has a third invariant dependency that accounts for failure mechanisms in brittle materials.

Jan 1, 2004

By P D. Katsabanis, W Roberts

Commercial explosives exhibit non ideal behaviour which is very difficult to model. The fume spectrum produced by commercial explosives apart from its practical significance for underground mining is of great theoretical importance since it reveals information about the chemistry of the detonation process. Emulsions, watergels and dynamites were tested under various degrees of confinement in an one cubic metre closed chamber. Sand, concrete, steel and copper pipes were used to alter confinement. The degree of confinement was found to significantly influence the quantity (litres/kg of explosive) and the relative proportions of toxic and non-toxic fumes (percent of total fume measured). These results lead to further confinement testing using various rock materials. Fume results, and thus detonation performance were found to be dependent on the type of rock material used for confinement. Materials such as dolomite, limestone, and granite were found to result in a relatively high detonation efficiency of the subject explosive as shown by the distribution of detonation fume products. Conversely materials such as sandstone, talc and massive sulphide resulted in fumes suggesting low relative detonation efficiency. Fumes appear to be a sensitive indicator of the completeness of reactions occurring within the expansion zone of the composite emulsion explosive, while the detonation velocity is relatively insensitive to small variations in confinement. Estimates of sonic velocities of the confining rock materials were found to show no correlation with VOD results. However good correlation between fume results and sonic velocity suggests that the performance of an explosive as indicated by the resulting fume spectrum is affected by the degree of confinement.

Jan 1, 1992

By Geraldine Rosenthal, Gadi Yohan, Roman Benram

Description of Project: Tamar Group’s civil division was awarded a contract to implode the Sun Hotel, an abandoned 14-story building located along Bat Yam’s coastline, roughly two kilometers south of Tel Aviv, Israel. On Nov. 6, 2012, Tamar Group’s experts positioned explosives in strategic locations of the building, targeting its central pillars, which then caused the building to collapse within seconds. Tamar Group used a relatively small amount of explosives in order to generate a well-controlled blast. This is the largest scale demolition carried out in Israel to date.

Jan 1, 2014

By Thomas Barkley

Mining tradition holds that a parallel round underground can not be any deeper than it’s smallest face dimension. ln other words, a mine using a 12’ (3.7 m) high by 24’ (7.3 m) wide room and pillar mine, the deepest pull that can be achieved is plus or minus 12’ (3.7 m). After experience with decking of rounds in a 12’ (3.7 m) diameter shaft to achieve more than 12’ (3.7 m) advance per round, the concept of deepening the pull on horizontal parallel rounds seemed to be a feasible concept. Tests were conducted in a conventional room and pillar metal mine with a round size of 12’ (3.7 m) high by 24’(7.3 m) wide. Standard rounds were drilled with a 16’ (4.9 m) steel as parallel rounds to an average depth of 14.5’ (4.4 m). The average depth of pull on these rounds was about 13’ (4.0 m). Using the available drilling equipment, 20’ (6.1 m) drill steel was used to drill holes to an average depth of 18’ (5.5 m). Five rounds were drilled and shot with a resulting aven$e pull of 16.2’ (4.9 m) or 90 % of drilled depth. Rounds were designed with decked bum cuts to maximize depth of pull in the cut area An innovative method of de&mining drilling accuraq was used to estimate it’s effect on depth of pull in the rounds. This method used a standard automatic 35-mm camera and scaling to determine the average drill deviation for many of the holes in the rounds.

Jan 1, 2000

By Fumihiko Sumiya, Yuji Ogata, Masahiro Seto, Yukio Kato, Yuji Wada, Kunihisa Utsuyama, Yoshikazu Hirosaki

It is well known that emulsion explosives can be dead-pressed especially in underground blasting. Voids in emulsion explosives will affect such malfunction of explosives. To clarify the factors that affect the dead-pressing phenomena, the characteristics of the pressure wave propagation in emulsion explosives were investigated. Three types of microballoons .or microbubbles, glass microballoons(GMB), resin microballoons(RMB) and chemical gas bubbles, were used as sensitizers for emulsion explosives. The pressure profiles inside the explosives were measured to determine the effects of the microballoons or microbubbles contained. The underwater explosion test and the large-scale drop hammer test were carried out to load the explosives with a dynamic pressure and a quasi-dynamic pressure respectively. In the underwater explosion test, the pressure profiles in the emulsion explosives were measured by a piezo-electric pressure gauge inserted to the center of the explosive cartridge which had a diameter of 30mm. In the large-scale drop hammer test, the same type of pressure gauge was placed at the bottom of the explosives. From these experiments, the following results were obtained ; A) The pressure profiles in the sample explosives sensitized by RMB or chemical gases were sharp, while in the sample explosives sensitized by GMB the profile was broad. B) The peak pressure levels in the sample explosives sensitized by RMB or chemical gases were twice as high as that in the sample explosives sensitized by GMB in the underwater explosion test. However in the large-scale drop hammer test, the amplification of the peak pressure is low compared with in the underwater explosion test. C) The impulse value was independent of the types of the microballoons or microbubbles in both tests. It was concluded that the type of the microballoons or microbubbles significantly influenced the characteristics of the pressure wave propagation in emulsion explosives.

Jan 1, 2001

By Brent Blanchard

The use of explosives to safely fell structures can be traced back over 300 years. Since then, dozens of chemists, inventors, blasters and demolition experts worldwide have played prominent roles in the evolution of what has become the modern-day explosive demolition industry. In America, one of the earliest applications of explosive demolition occurred in response to the great fires of San Francisco, where homes and businesses were blasted with gunpowder in a desperate attempt to create firewalls. Later in the 19th century, inventions such as nitroglycerine, dynamite and blasting caps made structural blasting a safe, efficient alternative to conventional demolition methods. The 20th century brought the first experiments in shaped charge technology, and this, combined with developments in portable seismology and non-electric delay systems, allowed an ever-expanding variety of structures to be explosively felled by demolition experts throughout the country. The 1950s and .60s brought a new wave of commercial structural-blasting entrepreneurs (several of whom are still active today), and their efforts towards improving adjacent-structure protection and public relations beget the felling of large commercial buildings in dense urban environments. By the late 1980s, publicity-driven motives were gaining greater influence in the decision to .implode. various structures, and the transformation of blasting operations into promotional spectator events played a role in several injuries and fatalities. Since that time, however, a renewed sense of responsibility practiced by most blasting firms and project officials has resulted in the safe, successful completion of hundreds of recent endeavors. In sum, what appears today as an efficient, economical - and visually spectacular - way to demolish structures has its roots in developments of the past several centuries

Jan 1, 2002

By David Harrison, Brian Harrison

The Army Corps of Engineers completed the Charleroi Lock and Dam in 1932. It is located on the Monongahela river approximately 22 miles (35k) south of Pittsburgh in Charleroi, Pennsylvania. It is comprised of a 420-foot (128m) gated dam, and a 720-foot (219m) by 56-foot (17m) land side lock, which provides for a 16.6 foot (5m) vertical lift.

Jan 1, 2018

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By Jonathan Zimmerling, Rob Alkins

The model of waves emanating from a blast hole proposed by Heelan, and further developed by Blair and Minchinton, provides an approximation of particle motion in an isotropic, continuous and homogenous medium caused by a cylindrical pressure source. Previous work in the literature shows that the shapes of the peak strain and peak particle velocity contours generated by this model are influenced by priming location. This paper presents the results of experimental investigations into the effects of priming position in an explosive column and the resulting shape of the surrounding stress and particle velocity fields. Fifteen emulsion charges were detonated in a limestone quarry, of which eight were bottom primed and seven top primed. The charges were fully confined, with no breakout to any surface. Particle velocity was monitored using tri-axial sensors coupled to the rock using cement, and pressure sensors were placed in water filled boreholes for fourteen of the experiments. Statistically significant differences in peak pressure for bottom and top primed shots were observed. Blair and Minchinton developed two pressure source functions, one of which is scaled using the charge weight scaling law. New models of the explosive pressure source are developed and compared to those found in the literature. These models are directly calibrated by predicting the peak velocities achieved at the known locations of the velocity sensors, then minimizing the residual sum of squares between the predicted and observed peak vibration values. Due to the complexity of the model the residual sum of squares cannot be minimized using standard non-linear optimization techniques, so a stochastic, agent based global optimization method is employed. Models are then cross validated by comparing the relative predicted differences in stress between bottom and top priming position to the observed differences.

Jan 1, 2013

By R Yang, D B. Kay

"Blast vibration control is of vital importance for tunnel blasting in urban environments. A vibration model with multiple seed waveforms (MSW) as input for a point of interest was developed in recent years by one of its authors. The MSW blast vibration model has been applied successfully in open cut and quarry blasting situations. From the literature, it appears that there may not be any seed wave-based vibration modelling work for tunnel blasting.A project was conducted to test the MSW model for tunnel blast vibration. A series of tunnel blast rounds were fired and tri-axial vibration waveforms from the blasts were recorded with several seismographs at distances ranging from 10 to 100 metres from the blasts. Seed waveforms were collected and the charge weight scaling law for the signature hole PPV were established.The MSW model is applied to tunnel blasting and specific issues associated with tunnel blast vibration addressed, such as variable effects of confinement and screening to vibration during a blast round. The capability of the model in terms of the PPV and frequency prediction is demonstrated in the paper. The paper demonstrates that the MSW blast vibration model is a useful tool for managing tunnel blast vibration with the potential to optimise round by round design in terms of managing the vibration below the limit while maximising tunnel advance rate."

Jan 1, 2011

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By J. Meissner

In this paper vibratory crack response is compared to that produced by volumetric changes in foundation soils induced by natural events. These natural phenomena include changes in the water table, changes in soil moisture, and formation of ice lenses to name a few. Previous papers have compared vibratory responses of cracks to atmospheric effects such as those produced by the passage of weather fronts and daily changes in temperature and humidity. Periodicity of these atmospheric effects is on the order of a day to half a dozen days. Thus it is possible to observe atmospheric effects with measurement over a period of weeks to several months. On the other hand, crack response produced by volumetric changes in foundation soils occurs over a period of many months and/or may be seasonal in nature if not longer in the case of drought. Thus its measurement requires long periods of observation (many months to significant fractions of a year) or observation during critical seasons. Since it occurs over long periods of time, its observation may be obscured by climatologically induced crack response. These soil volume changes are compared with climatic data to describe the correlative nature of crack response in time with the soil volume change phenomena and likely climatic causes.

Jan 1, 2009

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By Pierre DePasquale, Ricardo Chavez

Lowering of quarry energy consumption participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry. Within this global quarry project, blast design, as the first link in the chain, has to be optimized in order to satisfy requirements of downstream operations. The authors have been developing and implementing an operational methodology using continuous field measurements and field adaptation methods for blast design. It drives the drilling and blasting work, aiming at a more energy efficient and environmentally friendly operation. Based upon actual local conditions (rock-mass assessment, face geometry, borehole deviations, etc.), blast patterns are optimized through a specific hole-by-hole blast design software. It provides a better and more consistent energy distribution, to achieve a better rock fragmentation, while avoiding explosive overconsumption. The software also calculates total energy inputs and the drilling and blasting contribution to Greenhouse Effect. Coupled with methodical fieldwork and variable density explosives, it has been leading to a real reduction in energy costs and greenhouse gas emissions. As the project is now reaching its final stage, demonstrations were conducted in various quarries around Europe. Several simulations were carried out and compared to the site data, in order to propose enhancements for the different phases (extraction, loading, hauling, crushing and transport) while bearing in mind the environmental impact of the quarry. This blasting methodology allows to assess the carbon footprint of drilling and blasting in conjunction with the downstream operations, thus to evaluate the global carbon footprint of quarrying. Copyright ©

Jan 1, 2015

By Travis Davidsavor, Stanley: Dong Vitton

Concrete is a common construction material used throughout the world, and with increasing demand of fast-track construction, blasting and concrete casting are occurring simultaneously at many sites where rock is being excavated for concrete placement. However, there has been significant disagreement in the construction industry as to what intensity of shock vibrations green, or fresh concrete can tolerate. Peak particle velocities are often arbitrarily chosen, or are simply based on materials such as plaster and drywall that have been more thoroughly studied in relation to damage. Previous research on green concrete has used the concrete’s static strength subjected to shockwaves at different ages as the primary damage criteria. In addition, the static strength tests have been based on curing time. However, changes in temperature or humidity can dramatically alter the hydration rate, which affects strength development of different cements. To account for temperature changes and humidity the concept of concrete maturity is commonly used and allows the researcher to see where the concrete was in terms of hydration progress. In general, static testing determines the failure stress that the concrete’s macrostructure can handle, and often failure occurs in the natural materials first or along large defects in casting techniques. Dynamic testing or high strain rate testing, on the other hand, loads materials at such a high rate that larger defects do not have time to react and instead the microstructure is more highly stressed leading to higher strength and stiffness values. This is known as the material’s strain rate sensitivity. Since dynamic testing better tests the microstructural strength, it is believed that it may provide a better way to assess damage to green concrete. Testing includes both static and dynamic compression as well as static and dynamic splitting tensile strength to assess whether damaged has occurred to the concrete. No significant statistical evidence was discovered that damage to the concrete occurred at five different “green” maturities from peak resultant velocities ranging from 10.66 in/s (271mm/s) to 4.40 in/s (112 mm/s) with average intensity of 6.7 in/s (170mm/s).

Jan 1, 2003

By Harry Verakis, Thomas Lobb

This paper summarizes the course of mine blasting safety, particularly in underground coal mining, in the USA for over a century of mining operations. During the late 1800's and especially in the first decade of the 1900's, a large number of mine explosions occurred in which blasting played a significant role. A contributor to the large number of mine explosions during this time period was the use of black blasting powder to extract coal and other minerals. A review is made of some of the more significant underground coal mine explosions that resulted from blasting operations during this time period up to the present day. The safety measures that were adopted and required by a series of laws as a result of mine explosion disasters in which blasting was one of the factors are examined. The time line of historical improvements in blasting safety and the tremendous reduction in fatalities and injuries over a century is illustrated and discussed. The improvements, which included the elimination of black powder and dynamite and the introduction of safer explosives termed "permissibles" occurred slowly over time and culminated from the occurrence of many coal mine explosion disasters. The blasting accident history over the past decade is discussed to show the great gains made when compared to the first decade of the 1900's. The most recent blasting accident fatality that occurred in October 2006 at a U.S. underground coal mine is also discussed. Although the blasting accident record is significantly improved from over a century ago, continual improvement is needed to reach the goal of zero fatalities.

Jan 1, 2009

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001