Search Documents

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours.

Jan 1, 1997

By Takeo Ueda, Masashi Nakano

We have developed a new blasting system remotely controlled by an electromagnetic firing method, which has proved advantageously applicable to sites where rapid tidal current or deep water may cause serious troubles in underwater blasting operation by a conventional method.

Jan 1, 1983

By V Krishna Mohan, J Edmund Hay

This paper discusses the results of the gap sensitivity measurements made on water-gel explosives, sensitized by monomethylamine nitrate (MMAN) and flake aluminium, and one emulsion explosive. This study specifically deals with the effect of the mode of initiation, end or center, on the measured L50 values with air gap and coal dust gap for the above explosives. Similar measurements have also been carried out on a nitroglycerine (NG) - based explosive. The results show that the mode of initiation plays an important role in determining the air-gap sensitivity of these explosives. However, in tests carried out with the coal dust gap, the L50 ( grams of coal dust ) values for these explosives are close in both the types of initiation. The results indicate that the sensitivities of these explosives may be ordered in the following manner: NG-explosive>> Aluminized explosive ~ MMAN-explosive > Emulsion explosive

Jan 1, 1982

By Atsuo Inoue, Toshihiro Ogata, Hideaki Sugihara

Generally in Japan, since ANFO has easy handling and low-price, it is most used as industrial explosives. However, ANFO is very easy to dissolve in water, it is difficult to use under existence of water and the consumer have desired water-resistant ANFO which has perfect water resistance. Then, we have developed the Water-Resistant Granular Explosive (It is written as following WRGE.) in which the surface of the explosive was covered by waterproof film, so that WRGE is able to use in hole with water. We ran various performance tests about the WRGE developed in the laboratory. Consequently, WRGE has water resistance of over 6 hours, and it has been checked that a performance and handleability were equivalent to the conventional ANFO. Then, we carried out the field test in the consumption site, and did performance evaluation on an on-site level. As compared with ANFO, fragmentation (size and volume) and handleability are almost equivalent. However, some problems which the WRGE is not settled out smoothly in hole with water and need more time for loading were also clarified. We are going to continue some advanced improvements through field tests.

Jan 1, 2005

By Peter N. Calder, John N. Tuomi

The development of a successful control blasting program for an open pit iron mine in hard jointed rock is described. The objectives and mechanics of control blasting are discussed. Design and implementation procedures, which should have wide application, are given. Small diameter angle hole pre-split blasting, buffer blasting with production holes in front of pre-split lines and in front of strongly defined rock structures, and vibration control of production blasts are dealt with.

Jan 1, 1980

Fracture Control Blasting is an alternative to pre- and post-splitting or smooth wall blasting. It was developed at the University of Maryland as an attempt to overcome some of the disadvantages that occur with normal blasting practices. There are two main factors that are unique to fracture control blasting. First, it utilizes a notched or grooved borehole to initiate fractures at desired locations and secondly, it employs a very carefully selected charge so as to provide control over borehole pressure. The maximum borehole pressure must be kept between very definite limits in order to obtain initiation of fractures at locations where they are desired and yet not obtain fractures where they are not desired. When coupled with stem induced fracturing, which was developed for oil and gas well stimulation, it has been found that the charge required for fracture control can be as little as 1/40th that required for normal smooth wall blasting. The paper describes the technique of fracture control blasting and gives results of some of the field testing conducted to date.

Jan 1, 1984

By Park McLure, Paul Kunze

Abandoned underground mine workings have been regularly encountered in open pit mining excavations for many years, for the most part without many serious problems resulting. During the last several years however, some tragic occurrences and near misses have resulted when these old workings were intercepted. This paper will report on the problem as it relates to western open pit mining and will describe several techniques that can be used to identify problem areas before they are reached: Utilization of old maps and engineering data, long hole drilling and probing, and the use of subsurface investigation in the form of ground penetrating radar are the detection methods that will be discussed. The paper will describe some possible actions, once potential problem areas are identified. Drilling and blasting crews are usually exposed to the hazards involved when these situations arise because of their "on the ground" working environment. It is therefore appropriate that some of the best methods of dealing with these hazards once they are identified, seems to involve innovative and creative blast designs. The paper will discuss these approaches and describe an example of this aspect of the solution.

Jan 1, 1993

Computational techniques in determining particle size distributions after blasting is getting wide acceptance. A well known approach to extract this kind of information from digital images is edge detection. The number of edge points on a given image increase proportional to the increase of the particles on the image. By selecting a conveniently smooth threshold, counting the signed edge pixels may be a suitable metric further used to quantify the number of particles in the image. Here we propose an image processing algorithm together with Adaptive Neuro Fuzzy Inference System (ANFIS) to efficiently count the rock particles with various sizes on a given surface. To determine a suitable approximation for a mapping between the number of edge pixels and the number of particles, ANFIS is a suitable tool. As a trainable classifier ANFIS proved itself as being better efficient approach than other well known multilayer perceptron classifiers. ANFIS is trained by using convenient training data pairs previously experienced from empirically counted sample images. When given a new image containing the particle information of selected surface, the hybrid neuro fuzzy image processing approach provides satisfying performance on counting the correct number of particles up to the given scale of sizes. In this paper an experimantal study for assessment of particle size using ANFIS is presented.

Jan 1, 2004

By Daniel B. Conn, John L. Floyd

PhotoSeis™ is a blast analysis method that combines the advanced technologies of high speed motion picture photography and digital seismology. When fracturing rock with the use of explosive energy, the human eye cannot detect the details of the process due to its short duration. An extended time base is required to accurately quantify the response of the rock mass to the detonation process. This time base is provided by the use of high speed motion picture cameras. The control of ground vibrations and airblast is an important consideration when developing efficient blast designs. High vibration and airblast levels can be an indication of improper design, inaccurate detonators, or adverse geology. Since many factors can elevate airblast and ground vibration, a greater understanding of the site specific response to the blast design is needed that is beyond the scope of simple seismographic recordings. By synchronizing the photographic record provided by the high speed motion picture cameras with the airblast and vibration information from digital seismological monitoring, the Photoseis™ technique can be of great assistance in controlling airblast and vibration and optimizing the use of explosive energy for rock fragmentation.

Jan 1, 1990

By Dieter Froelich, Giles Turcotte

In the near future, Bong Mining Company (BMC) will start mining a new deposit known as Zaweah II which is a narrow iron orebody requiring multiple row blasts with the bench floor as a free face. This called for the development of a new blasting technique. The article delineates the problem and its restrictions related to blasting. It also describes the approach which was taken for developing this new blasting technique which is essentially an application of the cratering theory with near spherical charges. Basic crater tests were conducted using various combinations of hole sizes, explosive strengths and delay patterns. From the results obtained, several alternatives were considered for production blasts and the most promising ones were evaluated.

Jan 1, 1980

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By J. A. Rodgers, K. C. Whitaker

The time domain during which an explosive detonates and causes rock to fragment and displace is on the order of tens of milliseconds. Because of this, the dynamic processes that occur during this time frame often become a source of confusion when trying to analyze the performance of explosive products in decked blast designs. As an illustration, the authors have experimentally examined explosives malfunction in decked blasts through state-of-the-art measurement techniques. The interaction of explosive products and blast geometry was examined in detail using the analysis of a series of decked blastholes. Explosive and initiator malfunction in decked blasts is often considered to be entirely the result of insufficient inert decking material, however, it is shown that rock properties and dynamic burden conditions may have a significant impact on decking performance. The successful application of deck-blasting technique for control of ground vibration amplitude relies on an understanding of the true dynamic performance of the blasthole.

Jan 1, 2000

By Josephine Bones, Robb Larson, Daniel Miler

Avalanches are commonly mitigated through the use of explosives at ski resorts and above transportation corridors. Surprisingly, very little research has been conducted on snowpack response to explosive inputs, and efforts to model this response have been limited. The purpose of this ongoing research project is to ascertain an understanding of the dynamic snowpack response in relation to explosive size and height above the snowpack, coupled with snow conditions, to enhance avalanche control. A system of sensors and computer-controlled data acquisition components has been created to record the movement of snow resulting from the charge detonation. The system records acceleration vertically and radially within the snowpack at two distances from the point of detonation as well as blast air pressure at one location during explosive events. The data at two locations allows inferences to be made about the transmittance and attenuation of shock waves through the snowpack radially as well as vertically. The data shows that raising charges above the surface results in increased snowpack dynamic response when compared to surface detonations. Applying power function regression to accelerations for individual charge elevations, it was determined that both radial and vertical rates of attenuation were not dependant on charge elevation. Additionally, raising the charge also resulted in increased dynamic response at depth within the snowpack

Jan 1, 2012

By Jason Baird, Seokbin Lim

Run up is a factor in Linear Shaped Charge (LSC) cutting for which an account must be made. It occurs on the initiation segment of the charge, and the cutting performance during this period is significantly lower. Previous investigations by the UMR Explosives Group observed that similar effects occur not only with LSCs but a wide range of other explosives applications, including explosive-driven flux-compression generators. Prior to this investigation, it was believed that the main contributing factors to run up were from the combined effects of explosive run up (detonation pressure), lack of confinement at the free, initiation end of the charge, and penetrator transition from segmented pieces to a long-rod penetrator blade. As an initial step to understanding the mechanics of LSC run up, a series of investigations was performed in which the testing series was divided into several sub-categories (explosive detonation pressure run up, lack of confinement and long-rod penetrator concept) in order to reveal the effect of each on the run up. Predominantly, commercially manufactured LSCs were used for the investigation, and the entire testing was completed by the UMR Explosives Group.

Jan 1, 2006

By Michael A. Peltier, Dennis V. D'Andreal, Larry R. Fletcher

Accident data obtained from the Mine Safety and Health Administration (MSHA) were analyzed by the Bureau of Mines to determine the most frequent causes of blasting accidents in U.S. mining and to examine trends in blasting accidents. This accident analysis is an update of a similar blasting accident study conducted by the Bureau and published in 1983. The analysis shows that there has been a recent reduction in mine blasting accidents: The annual average number of nonfatal injuries has decreased from 107 for 1978-81 to 46 for 1982-85. The annual average number of fatal injuries was reduced from 11.3 to 5.0 during that time.

Jan 1, 1987

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By Christopher Smith

The critical nature of detonator function in blast design and its effects upon performance and safety of a blasting operation are well documented. Numerous laboratory and field studies have shown dynamic shock waves, generated by the detonating explosives in a shot, to be detrimental to the performance of the explosive columns in the adjacent boreholes. Laboratory tests conducted in Japan have explored the possible effects of dynamic precompression upon cartridges of emulsion explosives, which had been sensitized with different hotspot void producing methods. These tests uncovered significant differences in the magnitude of the dynamic shock wave pressures measured inside the different emulsion explosive cartridges, and demonstrated these pressure differences by crushing detonator shells inserted inside the emulsion cartridge. Basically, the results of these tests clearly showed the magnitude of the compressive force applied to the detonator inside the primed explosive cartridge to be a function of the mechanism that had been used to sensitize the emulsion (i.e., glass microspheres, plastic spheres, chemical gassing). The current study was designed to further explore the actual detonator failure mechanism in these dynamic precompression tests using live detonators inside the emulsion cartridge as opposed to empty detonator shells. The testing involved inserting commercial delay detonators inside emulsion charges, which had been sensitized with common hotspot void producing agents, and subjecting the primed explosive cartridge to the dynamic pressure wave generated by an underwater donor explosive charge. The effects of variations in the emulsion’s sensitization method upon the damage inflicted to the detonator were studied. Depending upon the degree of detonator damage, detonator crushing can lead to varying degrees of detonator malfunctions, ranging from sympathetic initiation of the detonator, to a reduction in delay time accuracy, to reduced detonator output, to complete detonator failure. Each of these malfunctions can have serious detrimental effects upon the performance and safety of a blasting operation.

Jan 1, 2006

By C. Lownds, U. Steiner

In 2008 a paper from the same source describing four actual cases of exposure of electronic detonators to lightning strikes was presented. It was shown that electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. At the time of submitting this abstract no further incidents with lightning have been experienced. As a result of those original incidents, and in order to understand how the safety devices inside electronic detonators break down, two series of tests have been done, each with 2 detonator designs. In the first series detonators were subjected to capacitor discharges up to 6kV and 1kJ in energy. In the second series the intensity was increased to 800kV and 24kJ in energy. In the second series, more electrical energy was delivered to the detonator assembly than the explosive energy of the detonator. In both series both detonators showed a spectacular ability to resist very high discharge energies. The tests are described in detail with supporting photographs. The data for both pin-to-pin and pin-to-case (more relevant to lightning) are presented and discussed. The mechanism of breakdown of safety devices is now understood better and the learning is being used to design more robust products. This high-voltage testing is relevant in understanding how electronic detonators might initiate as a result of a very close or direct lightning strike 1. Orica

Jan 1, 2009

By Robert B. Hopler

The Hercudet ? Nonelectric Delay Blasting Cap System has undergone significant changes since the last paper on the subject was presented at the 1978 S.E.E. Conference. The changes have been made to improve reliability of the blasting machine at low temperatures, and to improve efficiency and economy in usage in surface mining. The paper includes examples of the blast design process, details of use of the new in-hole connected cap, and delay patterns which have found use in quarrying and coal stripping.

Jan 1, 1980