Search Documents

By A. Ghadyani

This investigation was undertaken to assess the possibility of ash and sulfur removal by microbial action of high sulfur-content coal. Thiobacillus ferrooxidans and Thiobacillus thiooxidans have been used for biodesulfurization of coal. Feed samples were provided from Tabas coal mine located in Yazd province, Iran. The sample contained 28.80% ash and 2.30% sulfur. Flotation tests were implemented to optimize the effective parameters in these cells which were constant during bio-flotation tests. According to the results, obtained from various tests using Taguchi orthogonal array design (L27), the values of optimized parameters were pH at 7, 1000 g/t gas oil as a collector, 10% solid content, 15 min conditioning time, 100 g/t MIBC as a frother and 800 rev/min rotor speed. Bio-flotation tests are carried out by means of laboratory double discharge cell and mesophilic bacteria as depressant reagent using above mentioned optimized parameters. The bio-flotation experiments were conducted based on a Taguchi orthogonal array design (L9) with four variables (bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time). The collected data was analyzed by using DX7.0, Minitab14.0 and WinRobust1.02 softwares for evaluation the effect of each parameter on the optimization criteria. Considering the highest combustible recovery and the lowest ash and sulfur content, the value of optimized bacteria type, bacteria count, rotor speed of mixer and bio-conditioning time were Thiobacillus ferrooxidans, 5×107 cells/g(coal), 100 rev/min and 20 min respectively. Under this condition, ash and sulfur content and combustible recovery were predicted 12.39%, 2.08% and 82.03% respectively.

Sep 1, 2012

By G. Demi

Chromium ore exploitation has commenced in 1948 in Albania and there are produced about 24.3 million tons up to the end of 2006. Last years the prices and need were increased notably. Main export of chromium ores and concentrates was accomplished respectively 114 500 ton and 13 000 ton in People Republic of China during 2006 year. Location, status, reserves and grade of chromium deposits of Albania are presented in the paper. Chromium ore enrichment is related with their composition and Cr2O3 content, as well as with market requests. Actually, high grade chromium ores with Cr2O3 content over 38% ~ 40% are directly exported or treated in metallurgy, but last time have been exported and chromium ores with 28% ~ 30% Cr2O3 content for the reason that dressing plants can not be operated for investment lack. High grade chromium ores have been treated in heavy media separation plant before 1990. It is presented flow sheet, figures and necessity to put in operation HMS plant in the paper. Actually, low grade chromium ores with content 16% ~ 20% Cr2O3 are not enriched for the lack of investments, but before 1990 they have been concentrated in dressing plants producing chromium concentrates grade 48% ~ 50% Cr2O3. In the paper are shown technological schemes and industrial figures during more than 20 years operation and possibilities to reconstruct these mineral processing plants. Only chromium mineral processing plant of Bulqiza is in operation using as raw material its old existing tailings. The flow sheet and figures show that are possibilities to increase recovery and grade of concentrate in the plant. Separation and concentration of slimes in suitable equipment gives visible improvement of Cr2O3 recovery. Several tests have been carried out with flotation and magnetic separation methods for enrichment of low grade chromium ores. Flow sheet and figures of mineral processing ores content olivine as gangue mineral are interesting, because combination of gravimetric with magnetic methods is necessary in this case. In the paper are presented the tests and good results of low chromium ore pre concentration. Metallurgical treatment of chromium ores to produce Ferro chrome, as well as technological process, figures, consume of electrical power and materials in Elbasani and Burreli furnaces are shown and necessary investments to treat in metallurgy all produced chromium ores in Albania are considered.

Jan 1, 2014

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

By Alok Tripathy

A simulation code called SIMJIG and the user interfaces have been developed using discrete element method (DEM) and the .NET platform respectively for the jigging process. DEM platform is used for tracking of particles in the jigging operation. DEM uses the net force balance on the particles to track the trajectory of the particle. Simulation results are compared with experimental results obtained by jigging of low grade iron ore lumps. Two different iron ore samples one from Chatishgarh and one from Odisha were used for the experimental studies. The Alljig? stratification test rig meant for batch laboratory experimental studies has been used in the present work. The behavior of different sizes of material on jigging has been examined. Later, the particle size behavior during jigging at different layers of the jig bed has been studied. Further stratification profile across the jig bed has also been studied. It was observed that simulation results are matching quite nicely with the experimental results. The SIMJIG simulator developed in the present study could be used for predicting the performance of the jigging operation effectively. Keywords: DEM, gravity concentration, jigging, iron ore, simulation

Sep 1, 2012

By E. Lee

With the growing environmental concern, as well as the increasing concern for sustainability of natural resources, the need of improving the performance and efficiency of today?s crushers is be-coming increasingly important. However, the development of existing crushers requires an extended basic knowledge about the crushing process itself. The aim of the present study is therefore to find the theoretically optimal way of crushing compressively under given circumstances. In the present paper, optimizations have been performed with the purposes of maximizing product yield and minimizing energy consumption. Performed on an ideal crushing stage free from physical limitations, the optimization results have been obtained in terms of number of compressions and their corresponding compression ratios. Complementing earlier results on interparticle breakage (Hulthén et al., 2006), presented here are thus the results from corresponding optimizations with single particle breakage and interparticle breakage. It is concluded that modern crushers are not working optimally in any of the studied aspects for gneiss. In fact, optimizations indicate that a lowering of the compression ratio, as well as a shortening of the crushing sequence, are theoretically favourable. The outcome of this study is therefore highly promising as to giving new ideas and suggestions of improvements in existing crushers, and can even result in redesign of compression crushers.

Jan 1, 2014

By Aline Tavares

This paper describes the investigative studies carried out at Vale´s Center of Mineral Development (CDM) for a nickel sulfide deposit aiming to develop an adequate flotation flowsheet. The CDM facilities comprises of very well equipped laboratories to develop hydrometallurgical, comminution, flotation, physical separation processes, besides chemical and mineralogical laboratories, that are required to accomplish pre-feasibility studies, new process routes developments and, eventually, brownfield projects. Close association of the flotation group with the geometallurgy and the mineralogy teams play a key role during greenfield project development. Most of the information required by process engineers responsible for the flowsheet development can be provided by the mineralogy team and its mineralogical laboratory at CDM. During the flowsheet development of this nickel sulfide deposit, two ore types were identified as the most abundant in the deposit, named biotite-chlorite hydrothermalite (HID) and magnetite hydrothermalite (MAG HID). Six samples were selected for the investigative studies based on this initial information. Nickel grade varied from 0.39% to 1.95%. The main nickel-bearing minerals were millerite and pentlandite whereas the main non-sulphide gangue minerals were quartz, plagioclase, biotite, chlorite, actinolite, and/or magnetite. Electron microprobe (EMP) identified the presence of nickel in solid solution in gangue minerals such as biotite, chlorite, and actinolite. Nickel deportment in silicates varied from 3% to almost 40%. Magnesium was distributed in biotite and chlorite, except in sample MAG HID, in which talc was responsible for almost 50% of the Mg content. Liberation studies indicated that the optimum feed grind size was around 150µm and that pyrite occurred highly associated to the nickel sulfides. The flotation tests were planned based on the information provided by the mineralogical data. Rougher flotation tests indicated that the optimum P80 of the primary grind was 212µm for the HID type and 150µm for the MAG HID. From the reagents tested, amyl xanthate proved to be the most efficient in the recovery of the sulfides. In the MAG HID sample talc was well depressed by dosing 600g/t of CMC. Nickel recoveries in the rougher stage were lower than 90% due to the nickel distributed in silicates. However, sulfur recovery was around 95%, indicating high recovery of the total sulfides. Open circuit and locked cycle tests were conducted to evaluate the effect of the regrind size in the nickel grade and recovery (P80 of 44µm and 20µm). Nickel recovery decreased from 70% to 65% when finer regrind size was tested. Although nickel recovery decreased by 5%, the finer regrind size lead to a higher Ni grade (from 11% to 23%Ni) and lower fluorine grade (from 1138ppm to 700ppm) in the concentrate. Keywords: nickel sulfide, flotation, mineralogical characterization, flowsheet development

Sep 1, 2012

By P. M. Solozhenkin

On the territory Sakha (Yakutia) are located largest in Russian Federation reserves of antimony ores, Sarylakhsk and Sentochansk deposits, amaunt 10% of world stocks of antimony. A processing gold antimony ores Sarylakhsk deposit is carried out on gravitation-flotation circuit to receive gold gravitation concentrate and gold-antimony flotation concentrate with the contents of antimony over 60%. The gold-bearing concentrate is treated on place hydrometallurgicaly to a high-standard product, accepted by gold bank cash department. At the ore dressing plant reached the highest recovery in world in a concentrate of antimony 90%~91.6%, and gold 85.7%~86.0% as a result of scientific research works. Studied the mechanism of interaction cations of metals Pb2+, Cu2+, Cd2+, Hg2+, Ag+ with a surface antimonite presented on the basis of modern physical-chemical methods: nuclear quadrupol resonance, x-ray electron spectroscopy, electron spin resonance. The industrial tests of sodium dimethyldithiocarbate were carried out which confirmed high recovery of Sb and As. The leaching Sb2S3 by bacteria Desulfovibro desulfuricans and transformation antimonite in antimony trioxide by Tiobacillus Ferrooxidans improved following cyanidation . The extraction of antimony in a solution 96.0%~98.0% under optimal conditions. The common total extraction in the appropriate commodity products for gold reached 98%, for Sb 96.5%. At a combination of bioprocessing and cyanidation 85.5% of extraction Au was achieved. The new solvents for antimonite were found. Now by the Close Joint-Stock Co ?Sarylach-Antimony? industrial plant is constructed for processing Au-Sb concentrates to receive antimony trioxide and gold from various antimony deposits of Sakha (Yakutia).

Jan 1, 2014

By B. J. Zhang

Conventional spirals are capable of providing excellent clean coal recovery, although at a relatively high ash content. Compound spirals, which provide two stages of spiral cleaning in a single taller unit, have been commercialized in recent years to improve upon the cleaning performance obtained from conventional spirals. The present study aimed at optimizing the performance obtained from a compound spiral for cleaning especially high sulfur fine and ultrafine coal. Industrial-scale spiral units were utilized for this study in a pilot-scale facility at the Illinois Coal Development Park. A statistically designed experimental program was conducted to optimize ash and sulfur cleaning performance of the compound spiral. It was found that significant cleaning of ultrafine coal (i.e., 150 microns × 45 microns and even 45 microns × 25 microns size coal) is achievable with the compound spiral. However, operating conditions for cleaning finer coal fractions (-150 microns size coal) have to be significantly different from those used to clean coarser coal fractions (+150 microns size coal). The sulfur rejection trends were different from ash separation efficiency trends in all size fractions except 45 microns × 25 microns. The probable error (Ep) and effective specific gravity of separation (SG50c) determined for the compound spiral cleaning of the overall particle size were as low as 0.07 and 1.62, respectively. However, the bypass of a small percentage of clean coal to the tailings stream of the compound spiral, may need further adjustment of the key process parameters.

Jan 1, 2014

By Güven Önal, Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Mustafa Tarkan

There are various types of natural zeolite deposits in Turkey. Naturally occurring zeolites are excluded from many important commercial applications where uniformity and purity are essential. In this paper, the beneficiation of natural zeolite, taken from western part of Turkey, was investigated. According to X-Ray Diffraction (XRD) and mineralogical studies carried out on the representative ore sample, the natural zeolite was found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals.

Jan 1, 2003

The addition of copper sulfate to mineral slurries in order to ?activate? sulfide mineral surfaces for enhanced collector molecule adsorption, and hence enhanced recovery via flotation, is a com-mon mineral processing practice. It has been established in a laboratory situation that the addition of CuSO4 in conjunction with xanthate collector increases the flotation rate of pentlandite as compared to the addition of collector alone. However, it remains unclear whether the addition of CuSO4has a similar effect within mineral processing circuits. We examine here the effect of pre-activation oxidation on the copper activation of pentlandite and monoclinic and hexagonal pyrrhotite. All activation experiments were carried out at pH 9 using a total solution content of copper ions equivalent to one monolayer (0.210 -4 moles, 110-4M). Copper loss from solution was extremely rapid in all cases with less than 10 % remaining after 10s. EDTA extraction and solution analysis clearly demonstrated that copper activation was via direct surface adsorption and not an ion exchange process, as is the case for sphalerite, and that most copper on the surfaces is in the form of Cu(I). ToF-SIMS analyses of the mineral surfaces subsequent to copper activation show increased surface oxidation on increased conditioning time prior to copper activation. However, there is a significant decrease in surface oxidation on comparison of samples that have otherwise been prepared in the same manner but where one has been exposed to copper solution rather than water. This suggests that copper activation stabilises the surface and reduces the propensity for oxidation. Regardless of the length of pre-activation oxidation time only Fe(III) (no Fe(II)-S) was observed by XPS analysis, indicating a highly oxidised surface layer dominated by Fe-O-OH species. The presence of Cu(II) on the mineral surface is indicative of the formation of Cu(II)-containing precipitates and indicates non-mineral specific activation resulting in increased recovery but lower grade. Mineral specific copper adsorption, as evidenced by the presence of Cu(I), is required to improve both grade and recovery. Prolonged oxidation prior to copper activation causes a reduction in the Cu(I) to Cu(II) ratio on the mineral surfaces as compared to either fresh surfaces or surfaces oxidised for 1 minute only. This strongly indicates that the copper activation process is less effective on highly oxidised surfaces.

Jan 1, 2014

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various ore complex ore and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides (pyrite, arsenopyrite, pyrrhotite, chalcopyrite and galena) and other phases (including hematite, magnetite and goethite) for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay and Gorain, 2014; Chattopadhyay et. al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2018

By Sanjay Agarwal

Polymetallic sea nodule is a good source of manganese having 22.3% Mn, 5.4% Fe, 6.14% Si, 1.1% Cu, 1.15% Ni, 0.076% Co & others. These nodules are available in plenty on the sea beds, generated over thousands of years. Nodules mainly consist of manganese dioxide and iron oxide phases and other metals are entrapped in the complex cage of these Mn-Fe oxides phases.World-wide research is going on sea nodules as an alternative future source of many metals, which has led to intensified efforts to develop practical and economical processes for recovery of these metals. Very little attempt has been made world over on manganese extraction from sea nodules. We at CSIR-NML, India have developed a direct reduction smelting process of nodules to recover manganese as Fe-Si-Mn alloy. This alloy is extensively used in the steel industry as deoxidizer and as an alloying element to make different grades of steel. Lab scale experiments were conducted to study the manganese distribution between Fe-Si-Mn alloy and FeO-SiO2-MnO-CaO-Al2O3-MgO slag at different temperatures by varying the basicity of the slag. The direct reduction smelting of nodules is carried out on 1 kg scale in 50 kVA electric arc furnaces to have Cu, Ni and Co alloy and Mn rich slag. This manganese rich slag is further treated in 50 kVA arc furnace to produce Fe-Si-Mn alloy. The composition of Fe-Si-Mn alloy obtained is in the range of Mn: 60-65%, Si: 14-17%, C: 1- 2%, S: 0.03% and the balance iron which is acceptable grade for industrial use. The equilibrium amount of MnO in the final slag is controlled by the temperature of the final melt and the silica, lime, alumina content of the final slag. Increasing the basicity of the slag plays a major role in minimizing the loss of MnO to slag, increasing the amount of SiO2 of the slag, increases the manganese loss in the slag. Increasing the CaO/ Al2O3 ratio of the slag decreases the manganese loss in the slag. Increasing the MgO/CaO ratio of the slag increases the manganese loss in the slag. Thus by adjusting

Sep 1, 2012

Producing robust agglomerates with desirable structural properties is the key to success of the heap leaching of complex, low-grade nickel laterite ores. Mechanically strong but porous agglomerates with narrow size distribution (e.g., 5 ? 40 mm) are required to build permeable and perennially stable heaps of 4 ? 10 m height. The characterization of granules? microstructure is essential for greater understanding and correlation with the concomitant mechanical properties and robustness. In this study, we used non-destructive, computed X-Ray tomography analyses and scanning electron microscopy (SEM) in tandem with conventional compressive strength,and integrity/stability tests to draw links between nickel (Ni) laterite agglomerate strength/stability, internal microstructure (e.g.,porosity, inter-particle bridges) and binder type. It is shown that binder composition (e.g., tap water vs. 30% w/w H2SO4) and post-agglomeration drying both significantly impact on granules? physicochemical and microstructural properties. Acidic binder, in contrast with tap water, leads to significant incongruent leaching of different species from particles during ore-binder mixing and agglomeration. Upon wet agglomerate curing, solidified/recrystallized leached species form strong intra-granular solid bridges which, lead to greater compressive strength of dry agglomerates. Structural stability/integrity of cured agglomerates in acidic solution, however, decreases dramatically due to greater porosity and acid solubility of intra-granular solid bridges. These findings are useful in shedding more light on agglomerate structure characteristics and their optimization for enhanced column and heap leaching with concentrated sulphuric acid.

Sep 1, 2012

By Bharat Garg

The coking coal or clean coal from raw material division, Tata Steel Ltd. is a prime source of energy for inhouse steel making. Coal reserves of semi soft coking coal at West Bokaro is beneficiated by dense media cyclone and froth flotation processes to produce clean coal. In dense media cyclone process two byproducts-middling and rejects are also produced along with clean coal. With the growing demand for clean coal, it becomes imperative to maximize the recovery of clean coal in beneficiation processes. This will help, not only in reduction in cost of production, but also in raw resource conservation, and proper utilization. In this context, a case study was conducted at West Bokaro to identify opportunities for clean coal recovery from by-products. This paper mainly discusses the process for recovery of clean coal from byproducts and study of further liberation of clean coal from byproducts for economic consideration.

Sep 1, 2012

By M. R. Hosseini

Among all gravity concentration methods, Shaking-table is the most effective one from the metallurgical point of view. In this study, Shaking-table was used for concentrating a manganese ore sample from Ghasem Abad area in Kerman, Iran. Experiments were designed by using L8Taguchi design with five variables and each variable in two levels. The influence of each variable and their interactions on the operation of the device was studied. The variables under investigation were: table slope, table frequency, water flowrate, feed rate, and particle size. The manganese concentrate grade and recovery were used as response variables. It was shown that water flowrate, table slope, feed rate, and particle size are the significant variable on concentrate grade; while, all the variables influence manganese recovery.

Jan 1, 2014

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of feldspar, quartz and wollastonite minerals, after contacting different triboecharging medium made of different materials, were considered. Their charge acquisitions by different size fractions of minerals were monitored and accordingly their energetic work function values were estimated. Moreover the separation behaviours of these minerals through the electric field of a laboratory free falling separator were determined and the effects of some chemical reagents on separation their separation characteristics were studied.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing quartz, feldspars, wollastonite and some other silicates. The results show favourable prospect to apply the triboelectric separation technique for beneficiation such a complex raw material."

Jan 1, 2003

By I. Baltov

The Chelopech Mine, located in Central Bulgaria, is one of Europe?s largest underground copper- gold mines, currently mines and processes approximately one million tonnes of ore per year. Copper concentrates containing gold and silver with significant arsenic content are produced and sold on the world markets. The operation was acquired by Dundee Precious Metals in 2003. A modernization program for the Mine and Plant has since been in progress to increase both production and mechanical reliability, and also to optimize metallurgical recoveries. Since then, mine output and plant throughput have doubled, plant availabilities and utilization have increased significantly, and overall metallurgical performance for copper and gold improved. The paper presents the systematic approach for obtaining and analyzing data, communicating it, and making suggestions for changes to the technological parameters and flowsheet in order to maximize metal recoveries. These studies have correlated the ore characteristics (particle size distributions, metal assays, and Cu and Au mineralogical and phase analyses) with the actual plant performance (kinetics, recoveries, and throughput). Cu recovery by size has been calculated from the mineralogical analyses of feed, concentrate and tails, with the most significant losses being identified in terms of fraction and phase recoveries. This has provided the recommendations (some of them tested in plant) for changes in the grinding and flotation circuits.

Jan 1, 2014

In recent years, coal beneficiation has gotten considerable attention. Selective oil agglomeration has been accepted as the best method to produce clean coal with a high removal of pyrite sulphur. In this study, spherical oil agglomeration of Datong coal fines was carried out using diesel oil as a bridging liquid. The oil agglomeration has a surface properties based on coal cleaning technique. The effects of fundamental parameters have been investigated including the concentration of bridging liquid, the size of coal particle, the solid content of slurry, the agitation time and rate, pH, surfactants on the agglomeration performance and various salts on the ash rejection and removal of pyrite of the agglomerated products. The optimum conditions of particle size, diesel concentration, solid content, agitation speed and time, pH and the dosage of active agent have been determined as less than 8µm, 20wt%, 1200r/min and 10 minutes, 7.5g/t and 100g/t, respectively. Under these conditions the ash content in the products can be achieved 1.5% below, the ash rejection was up to 92%. It has been observed that ionic strength of the aqueous medium affects the agglomeration performance. The precombustion coal cleaning process based on improved selective agglomeration results in high ash and pyrite sulphur removals. Over 80% removal of pyrite sulphur can be achieved from run-of-mine coals by offering a more cost-effective sulphur reduction solution rather than any other SO2 removal technology. In addition, the removal of pyrite sulphur is very necessary for not only the prevention of environmental pollution but also economical reasons.

Jan 1, 2014

By Z. Pokrajcic

The traditional comminution circuit is a major consumer of energy ? both as electrical energy and through consumption of media and wear resistant liners. Up to 40% of electrical energy con-sumed at a mine site is attributed to comminution however only a few percent of this energy is used in the generation of new surfaces from size reduction. This paper describes the evaluation of modifications using simulation models based on two operating comminution circuits. The aim of these modifications is to decrease both the amount of electrical energy consumed in the size reduction process, known as direct energy, as well as to decrease the consumption of grinding consumables such as steel grinding media and mill liners, designated as indirect energy. The approach is two-fold: ??Employ, where possible, autogenous grinding techniques to eliminate the need for grinding media and reduce mill liner wear. ??Optimise the use of the grinding energy distribution in the comminution circuit by using more energy efficient grinding devices to target typically problematic features of a comminution circuit such as critical size material from the primary mill and overgrinding in the secondary mill. The investigations show that significant total energy savings, as high as 50% in some cases, can be achieved by employing the techniques described while maintaining circuit throughput and product size. Investigations also show potential benefits in downstream flotation processes as the product size distribution generated from the eco-efficient circuit is generally ?narrower? in shape for improved flotation performance and containing less material in the coarse fraction for overall better liberation.

Jan 1, 2014