Search Documents

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By Markus A. Reuter, Antoinette van Schaik

"INTRODUCTIONGoods and products, such as passenger vehicles, are manufactured by using a wide spectrum of different raw materials to meet highest consumer requirements during use. Due to the time-varying composition and complexity of multi-component products such as cars, recycling is complicated. It involves a network of interconnected processes and material and energy flows. Improving the efficiency of the material cycle of the car to comply with the recycling targets as imposed by EU legislation, requires insight into all aspects influencing the closing of the material cycle (dynamics, technology, economy, legislation, etc.) and their mutual relation. In order to define the link between recycling end-of-life products, their changing composition and design a dynamic model was developed for the resource cycle of cars. The model integrates the optimisation of the material cycle with the dynamic behaviour of recycling systems."

Jan 1, 2003

By V. F. Petrov

Cyanide is widely used gold lixiviant for hydrometallurgical processes. The resulting tails contain complex toxic compounds. With reference to this, the protection of the environment should be the major issue. A complete detoxification of cyanides before disposal, a partial detoxification to the allowable concentrations and a disposal of tails at a polygon followed by the detoxification of excess water into the environment are offered as an environmentally friendly way of disposal. However, a complete detoxification of the cyanidation tails does not give the required results due to the presence of toxic compounds, cyanides and thiocyanates in tailings ponds. This is due to adsorption-desorption process occurring between solid and liquid phases. A partial detoxification is used to down cyanide to the allowable concentrations, which are safe to the environment. The storage of tails without detoxification is mainly used at low concentrations of toxic compounds in the disposed tails. With reference to this, water recycling is practiced by Russian plants in order to reduce as much as possible or almost eliminate toxic effluents into the environment. Fresh water is applied if necessary and to make up for water losses, with 8-12% of total water supply. This allows for the stability of water balance and the decrease of consumption of the reagents applied. The conditioning technologies of water recycling followed by regeneration of free cyanide and metals recovery as saleable concentrates are specially developed due to adverse impact of water recycling on gold recovery processes due to high concentration of base metals (copper). These technologies are also profitable. In order to detoxify cyanide in the tails for tailings dam, effective and inexpensive technologies involving a seasonal use of detoxified reagents were developed. For example, a technology with aldehydes use which is applied by a series of operations. Effluents disposed to the environment are detoxified using chlorination followed by almost a complete destruction of toxic cyanides and thiocyanates. Before disposal, chlorinated water is settled to precipitate the resulting hydroxides of metals and complete chemical reactions such as a full decomposition of hypochlorite ions. In order to protect ground water, watertight screens from local water-resistant materials are used. The samples of these materials were previously tested and chosen according to their maximum ability to adsorb toxic compounds in the tailings pond. If local water-resistant materials are not available, whole welded impermeable polymer screens are used. The options mentioned allow the storage of cyanidation tails in accordance with national ecological standards. Keywords: cyaninides, thiocyanates, wastes, environmental safety, recycled water-supply, detoxification, storage

Sep 1, 2012

By Hiroshi Sasaki, Herman D. Mendoza

"The surface-chemical property of nickel slag fiber was modified in aqueous media in order to act as an active and efficient collector of colloidal amorphous silica from geothermal effluent. Colloidal amorphous silica (0.05 µm) from geothermal wastewater causes operational and ecological problems. It clogs geothermal pipes and waterways, and when disposed to the environment poses hazardous effects on both the flora and fauna ecology. Because colloidal amorphous silica is extremely fine and remains in suspension in aqueous media, conventional solid/liquid processes to remove colloidal silica from its bulk liquid are rendered ineffective.A rapid separation technique is then developed to remove effectively amorphous colloidal silica from its bulk liquid by attaching the extremely fine particles of silica onto a nickel slag fiber coated with magnesium hydroxide, Mg(OH)2. The nickel slag fiber has the following characteristics: a high surface area and predominantly possesses negative charge in aqueous media with an iso-electric point at pH ~2.5. When soaked and saturated with Mg(OH)2 solution, the surface of the nickel slag fiber becomes coated with fine and compacted Mg(OH)2 precipitates. This modifies the surface- chemical property of nickel slag fiber transforming the negatively charged surface into a positively charged surface in aqueous media with an iso-electric point of around pH 11.8, which corresponds to the iso-electric point of Mg(OH)2. When geothermal effluent containing negatively charged colloidal amorphous silica particles (i.e.p. of silica is pH 2) is passed through a column-bed packed with surface-chemically modified nickel slag fibers under natural pH conditions, the colloidal amorphous silica particles are recovered by attachment onto the surface of the surface- modified nickel slag fiber. The recovery of colloidal amorphous silica by attachment is 97-99%, resulting in the production of a relatively clean and silica free output. Aluminum hydroxide, Al(OH)3, was also used to modify the surface –chemical property of the nickel slag fiber. In the same way, it also exhibited a positive response with the collection of colloidal amorphous silica from its bulk liquid, but yielding a lower recovery of 90%. This may be attributed to the lower surface potential and iso-electric point of pH 9.3 for Al(OH)3. The separation process was evaluated and analysed using existing potential energy theories. Figure 1 shows a micrograph of the surface of an unmodified and the Al(OH)3 –modified surface of nickel slag fiber."

Jan 1, 2003

By Shankar Narasimhan

Data Reconciliation is a technique that has been developed more than fifty years ago and has been refined over the past few decades and is now being deployed routinely in several process industries such as refining, petrochemicals, mineral processing and hydro-metallurgy. The main aim of data reconciliation is to obtain accurate estimates of all process variables and parameters using plant measurements that are invariably corrupted by random errors and may also contain biases and other gross errors. These reconciled estimates are subsequently used either in offline exercises such as simulation, retrofitting, and de-bottlenecking or in online optimization and control applications. In this presentation, a brief history of data reconciliation, its assumptions, and uses are reviewed. New developments in this area are highlighted such as robust data reconciliation to handle model uncertainties, and reconciliation using identified models derived purely from operating data. Several case studies in the mineral processing industries reported in the literature are also highlighted to indicate the potential benefits of this technique.

Sep 1, 2012

By Bulelwa Ndlovu, Saeed Farrokhpay, Dee Bradshaw

The effects of phyllosilicate minerals on the flotation performance and froth stability of a copper ore was investigated. It was found that various phyllosilicate minerals affect the copper recovery differently however they all caused the flotation grade to be reduced. The effect of different phyllosilicate minerals on the froth stability followed the order of talc >> montmorillonite > muscovite > kaolinite > illite. The results demonstrated that there could be a relationship between the deleterious effect of phyllosilicate minerals on the flotation and froth stability. Talc and montmorillonite have both shown the highest effect on the flotation recovery and grade as well as froth stability. On the other hand, illite has the least effect on the both flotation performance and froth stability. Kaolinite and muscovite also affected the copper flotation grade (but not the recovery) while they also affected the froth stability. Therefore it is possible to control the flotation performance when phyllosilicate minerals are present via monitoring and controlling froth stability which needs to be investigated further.

Jan 1, 2014

By Derek Caizergues, Hurman Eric

Experiments have been conducted at around 1700°C to determine the possibility of carbothermic reduction of alumina under the presence of a metallic solvent. Total pressure of the system was reduced to around 30kPa and metallic nickel, iron, copper and tin were selected as the solvent. The highest recovery of aluminium was achieved with the nickel solvent followed by iron, copper and tin. This ranking for the first three was also in accord with the extent of negative deviation form ideality in the respective binary solutions of these solvents with aluminium. The tin-aluminium system displays positive deviation form ideality. The rate and extent of reduction was found to be highly dependent on temperature and pressure. The pseudo first order reaction rate was found to be applicable to the process in all the solvents used. Rate constants were calculated and it is also suggested that the reduction was controlled primarily by the chemical reaction rate.

Jan 1, 2003

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation behavior are just a few of the parameters that are largely due to the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the inherent impact of surface wettability in nearly all industries, fields, and multi-phase interactions, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In this study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By D. J. Zhao

The reduction and nitridation of preoxidized ilmenite pellets were investigated with the prospect of creating grain refiners containing titanium oxides and titanium nitride dispersoids. All the reduction and nitridation reactions were conducted in a furnace with a thermogravimetric analysis system under a H2-N2 gas mixture of 5 L/min. The ilmenite pellets were reduced at 1100°C for 4 hours under 80%H2-20%N2 gas mixture, and then respectively nitrided at 700°C, 800°C, 900°C and 1000°C for 12 hours under 10%H2-90%N2 gas mixture. The products were characterized by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM), and analyzed by Energy Dispersive Spectrometers (EDS) and Electron Probe Mapping Analysis (EPMA). Iron oxides were reduced into metallic iron, and oxides of titanium were found, but titanium nitride particles were not identified in the products under the prevailing conditions.

Jan 1, 2014

By Vincent C. Smith, Agit Singh, Daniel de V. van der Spuy, Bernard Muller

"Process control in the minerals industry is made difficult by factors such as the multivariable nature of the processes, noise, many disturbances, the changing nature of the processes, nonlinearities, process constraints, slow responses and large deadtimes. A good example of such a process is a milling circuit, where all these problems are experienced. Since model predictive control (MPC) effectively handles most of these difficulties, Mintek decided to develop, customise and test an MPC controller for milling control.Conventional MPC uses a dynamic model of the plant to calculate the future (predicted) plant outputs based on the movements of the manipulated variables in the past. The future moves of the manipulated variables can then be calculated using an optimisation algorithm that will minimise the difference between the setpoints and the predicted outputs. The least squares optimisation method is the quickest, but it does not cater for process constraints. Constraints can, however, be handled explicitly by using a quadratic programming optimisation method. This method ensures that the variables stay within the constraints at all times, but the calculation procedure is much more computationally intensive.• modifying MPC for the Minerals Processing IndustryIt was found that in order to obtain good, robust control using MPC in the minerals processing industry, the conventional MPC algorithm had to be adapted. The MPC controller was first tested on an extensive milling simulator, which was specifically developed for that purpose. Problem areas were identified and the MPC controller was specially adapted to accommodate for these difficulties. Some of the adaptations to the conventional MPC algorithm and special features added were as follows:Since milling plants contain many integrating processes (e.g. sumps), and integrating errors can cause offsets and poor control, it was essential that integrators be handled explicitly. This problem was solved by adapting the algorithm and also using an integrating error portion to compensate for integrating errors.Constraints on the inputs and outputs adversely affected the control. The controller using simple least squares optimisation was tuned with the constraints in place, while the maximum expected setpoint changes were made. This ensured that the process would be able to handle most setpoint changes up to these expected values without violating the constraints. A later improvement on this method was the incorporation of a quadratic programming algorithm to perform the optimisation. This method handles limits explicitly and was shown to perform better than the least squares methods (at the expense of a much higher computational cost)"

Jan 1, 2003

By P. Somasundaran, G. Anastassakis, Z. Pan, D. R. Nagaraj

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By Homero Delboni, Mauricio Guimarães Bergerman

"At the regrind or secondary grinding stages of metal ores, usually the concern about the energy efficiency is extremely important. In general, the specific energy consumption at this stage is higher than in the primary stages of grinding. In addition, it has been observed a tendency of finer grinding in the new projects of metallic ores, due to the finer mineral liberation, which leads to an increasing capital and operational costs. In Brazil, during the last 10 years, regrind P80 sizes of approximately 40 to 20 ?m have been necessary in all new iron and copper plants. The use of conventional ball mills, adequate for primary grinding, can result in low energy efficiency with products below a P80 of 50 ?m. This paper presents an overview of the regrind circuits in Brazil that operate with vertical mills and the results of industrial surveys at selected vertical mill circuits. Where possible, comparison is made between the plant results and the design criteria and laboratory regrind tests used for the mill sizing."

Jan 1, 2014

By Khoi Nguyen, Luke Keeney

"Hardness" is an important yet diverse material physical property and is a key parameter in the mining industry in fields such as comminution, geotechnical and blast modelling. Several laboratory and field based measurement techniques exist to measure hardness (e.g. Point Load Testing, Vickers, Brinell, A*b, BMWi, UCS), all are designed for specific applications. Current tests are generally destructive and require specific sample preparation procedures which results in high cost tests that are not conducted in adequate quantities to map hardness across an ore body. The EQUOtip rebound hardness tester is a device that has been developed for application in ore body hardness domaining within the AMIRA P843 GeMIII Research Project. The rebound hardness test is non-destructive and suitable for application on half and whole diamond drill core. Data acquisition protocols and a data processing software application (EQProcess) have been developed to facilitate routine collection of comparative hardness information. This paper outlines the data acquisition and processing methodology and provides application examples of defining relative hardness domains in different geological deposit styles.

Jan 1, 2014

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By Wolfgang Öfner

Many technical processes also yield dusty residues which usually contain appreciable amounts of valuable matter. Often they also accumulate substances detrimental to the process. Dumping them entirely in landfills wastes raw material and causes high disposal costs, but recycling them without prior treatment is often not feasible. Physical separation processes are preferable because of their rather low energy demand. In order to develop such treatment systematically, the residues must be characterized properly. The technique for such a characterization is taken from mineral processing: perfect fractionation according to continuous properties of the particles supplemented with chemical analysis are used for plotting the Henry-Reinhardt chart. This represents the benchmark for assessing actual separation processes and tests. Their results are compared in terms of ?selectivity? and plotted in the kappa chart. In this paper, Henry-Reinhardt chart and kappa chart are applied to several different types of residues from iron and steel production and show their potential for being upgraded before reutilization in the production process. This approach is suitable for virtually all dusty residues from other industrial processes as well. Keywords: residue, dust,iron and steel, process development, Henry-Reinhardt chart, kappa chart

Sep 1, 2012

By B. Rath

An effective process plan is an important part of maintaining consistent recoveries in mineral processing operations. Traditionally, Mineralogical studies are completed using chemical and metallurgical methods to monitor recovery and elemental distribution. The development of mineralogy and more efficient processes in mineral analysis techniques means that mineralogy is now more accessible as an efficient and comprehensive study tool. As operating costs increase and feed grades decrease it is important to maintain tight control of process and ensured maximum recovery is maintained at all times. Just a few days of losses in recovery caused by changes in ore type or processing conditions can have a large effect on total metal recovery and profit. Mineralogical audits can be used to minimize these losses by monitoring the fundamental behavior of feed ore on a regular basis. Smart use of mineralogical studies can develop mineralogical and ore type benchmarks in a detailed, which can be used in process control and monitoring. Geological ore types can be used to identify key mineralogical parameters that may be used in routine and cost effective analysis. Mineralogical systems ideally suited to this because of the depth of information on everything from modal mineralogy to locking/liberation characteristics and mineral associations. Mineralogical studies can equally be applied to specific unit operations within the process, which can allow more detailed information to be gathered on areas of the process that have been identified as critical. This will be especially effective for flotation or oxidation processes where process parameters can be very sensitive to small changes in mineralogy. This paper deals with the Ore Morphology, Ore Mineralogy, Gangue mineralogy, Photo micrographs under reflected, transmitted light and XRD studies Ore, Mineral studies of Sub grade Iron ore of Bacheli Complex, Bailadila Sector, India. Keywords: mineralogy, liberation, liberation studies, ore mineral, gangue mineral, morphology, jasper, ferruginous clay

Sep 1, 2012

By T. B. M. Himawan

In this study, effect of thiosulphate and oxidation using oxygen were studied in arseno copper ore flotation. Single mineral study of chalcopyrite and tennantite in regard to the aforementioned techniques was also studied. Zeta potential, XPS, contact angle and floatability of single minerals were conducted for each treatment to understand the mechanism. It was revealed that the separation is best conducted in alkaline condition at where there will be interaction between thiosulphate and the mineral surface as well as the formation of hydroxide species in the oxidation using oxygen. From zeta potential of both thiosulphate and oxidation conditioning, it can be found that the reactivity of tennantite is much higher rather than chalcopyrite resulting higher rate of depression on both techniques as shown from contact angle and floatability of each mineral after treatment. XPS spectra confirmed qualitatively and quantitatively the existence of species responsible for the depression of each conditioning techniques. As for the copper ore flotation test, it is the oxidation using oxygen provides best performance after 60 minutes of oxidation. Keywords: tennantite, chalcopyrite, arseno copper ore A, thiosulphate, oxidation using oxygen

Sep 1, 2012

By Peter N. Holtham, Geoffrey J. Lyman, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong, Tim Napier-Munn

Studies of the dense medium and classifying cyclone have been conducted using the Fluent computational fluid dynamics code. Experimental measurements of the segregation of medium in a DM cyclone by gamma-ray tomography and the performance of a novel classifying cyclone design have been used to test and interpret the 3D CFD predictions. The predictions of the CFD models were generally plausible, though more work is required to incorporate turbulent mixing of the slurry in the cyclone. The benefits of the novel cyclone design were explained by the model in terms of conditions favouring reduction of short-circuiting at the vortex finder, and the removal of the air core from the wall at the apex. Work is continuing.

Jan 1, 2003

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018