Search Documents

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By S. Malkin, Z. Shi, H. Attia, D. Chellan

An experimental investigation is reported on creep-feed grinding of a nickelbased alloy (IN718) using conventional aluminum oxide grinding wheels. Straight surface grinding expe.riments were conducted on nickel-based alloy blocks over a wide range of grinding conditions with straight oil as- grinding fluid applied at high pressure. Grinding power, forces, workpiece surface roughness, and radial wheel wear were measured. Specific material removal rate as high as 64 mm2/s was Used without burning the workpiece, which can be attributed to the extremely low specific energy of 12.6 J/mm3. It was found that the grinding wheel under the present test conditions had a strong capability of self-sharpening as indicated by the stabilized power, forces, and surface roughness after an initial short transient.

Jan 1, 2006

By D. Murray

A 2-hectare uranium tailings area has been reclaimed. The exposed tailings of 1.4 hectares were capped with glacial till and vegetated with grasses and legumes. The water running through the tailings was diverted around the tailings in a line ditch and treated with sodium hydroxide and barium chloride. Difficulties occurred in placing the till capping because of the low bearing strength and the uneven surface of the tailings. This led to varying thicknesses of till and the need for manual labour in some areas. Total reclamation costs were $32,200, with vegetation establishment costs at $13,700 per hectare. This report provides a record of work for use in assessing the long-term suitability of these treatments.

Jan 1, 1979

"With the globalization of the mining industry, many companies are now seeking to invest in underground diamond mines, with the purchase of small diamond pipes being seen as particularly attractive. However, recent experiences in South Africa have shown that many projects fail due to a lack of awareness of the hazards associated with diamond mining. In this paper three significant hazards are dealt with — mud rushes, block crushing, and implementation of an inappropriate mining method. Measures that assist in the prevention of these three hazards are given.IntroductionFor over a hundred years, South Africa has been seen as the centre of the diamond mining industry, possibly having the largest number of operational underground diamond mines in the world. Despite the fact that this industry has been dominated by large mines of De Beers Consolidated Mines Limited, many small underground mines have operated profitably for a number of years, exploiting diamondiferous fissures and pipes. In the last decade there has been renewed interest in these small operations from international companies. However, many of these projects have not realized their full potential owing to a lack of appreciation of the hazards inherent in the operation of a diamond mine.Hazards Associated with Diamond MiningIn the development of a diamond mine, the mining company must be aware of the hazards associated with diamond mining. There are three main hazards: (1) mud rushes; (2) block crushing; and (3) selection of an inappropriate mining method (not a natural hazard, but a planning induced hazard). Each of these hazards will be dealt with in turn in the following sections."

Jan 1, 2000

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By A. Gakwaya, P. Vachon-Joannette, P. Gagnon, J. Lévesque

"Predictive numerical methods are essential tools for reduced development cost and improved high performance designs of modern aircrafts. Their use leads to savings in terms of design cycle time and experimental trials. Composite materials subjected to impact loadings demonstrate various damage modes such as matrix cracking, fiber breakage, delamination and, ultimately, fabric fracture. Composite laminates are extensively used in the aerospace industry, and their damage modeling is complex due to their inhomogeneity and anisotropic behavior. Damage evolution affects both in-service properties and performance of these composites. In this work, the drop-weight impact test has been simulated. Using a material model that accounts for both delamination and intralaminar damage, laminates response is analysed using numerical simulations based on 3-D finite-element models of the commercial code Abaqus/Explicit. Experimental and simulation results are compared, in terms of energy absorption and contact force. The obtained numerical results show good agreement with experimental data.INTRODUCTIONAs primary aircraft structures are increasingly being made from advanced fiber-reinforced polymer matrix composites and are in general exposed to a variety of impact scenarios (bird, hail, debris etc.), an understanding of the impact event and the performance of composite materials during impact is important in the development of new structures. This work is focussed on low velocity impacts that typically occur when foreign objects hit the aircraft during maintenance or other on-the-ground operations. These impacts can cause non visible damage that affect the structural integrity of the composite components. While for metallic structures, damaging impact events typically leave noticeable dents due to plastic deformation, in contrast, for high strength carbon fiber reinforced composites, they can deform elastically to strain levels exceeding 1% and the internal damage can often occur without the formation of a visible dent. The identification and effect of impact damage on the performance of the structure is thus of great concern to the aircraft industry as the durability and damage tolerance of these composite structures are strongly influenced by the size of detectable internal damage."

Jan 1, 2016

By S. Jordanov

The nature of processes that take place on top of copper bearing grains during the suppression of copper acid drainage from mine tailings was studied on a grain model. Cyclic voltammetry (C.V.) was employed as an experimental technique suitable for indirect measuring of copper leaching. Experiments were done in sulfuric acid (pH=2) at electrodes that progressively approach the real situation during acid main drainage, starting with Cu-metal, then with CuO and finally with CuO covered with CaSO4. Oxidation was found to be the only process that takes place on metallic copper electrode anodically polarized up to 2 V vs. Cu/CuSO4 reference electrode. Dissolution is intensive and reaches up to 50 mA.cm-2. When the same was repeated, but on CuO electrode, anodic currents were some 4 times lower than on the bare metallic surface. This indicates that the electrode material is not completely oxidized to copper(II)oxide and the Cu(O) or Cu(I) residues are oxidized during the anodic polarization. This explains the diminished dissolution. Dissolution is further restricted at electrodes covered with CaSO4. It is some 20 times lower than on the bare oxide electrode. When the second layer of CaSO4 was applied, anodic currents were another 15 times lower. Total decrease of anodic currents when transition is made from Cu-metal to CuO covered with 2 layers of CaSO4 reaches up to 7.500 times. C.V. measurements produced a proof that mechanical blockage is the way how lime prevents leaching of copper bearing grains in immobilization experiments referred elsewhere.

Jan 1, 2007

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013

By H. Alzraiee

Traditional planning methods such as CPM and PERT have been useful tools to manage construction projects. However, the underlying model of these traditional methods often seems to fail to represent real projects as they tend to assume no interrelationship between project components. In reality, project components have complex dynamic feedback process that requires modeling of inherent uncertainty in the execution of these projects. Nevertheless, this dynamic nature and uncertainty have not been explicitly addressed by traditional planning methods. Project failure can be attributed to poor representation of the inner and outer aspects of operations that are responsible for project dynamics. Uncontrollable external forces are often cited but the real cause may be internal such as the feedback process among components of the project. An alternative perspective is offered in this paper through system dynamics (SD) that accounts for the feedback process and discrete event simulation (DES) for modeling the uncertainty. The proposed method utilizes SD method for modeling project dynamics and DES method coupled with CPM network for operational details and uncertainty, respectively. A case study that involves preparing engineering drawings in a design office is used to demonstrate the use of the developed method and to highlight its capabilities. Modeling the dynamic dimension is expected to enhance planning and scheduling of construction operations and to provide a better understanding of the impact of various internal and external factors on project schedule and productivity performance.

Aug 1, 2013

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By M. B. M. Monte, M. L. Torem, E. R. Pecanha, A. G. Merma

The recent literature has unveiled the potential use of microbial strains in mineral bioprocessing. This study presents the use of a Gram-positive bacterium (Bacillus subtilis) as bioreagent for hematite flotation. The bacterium presents the ability to modify the properties of mineral surface (electrophoretic mobility and hydrophobicity). It was studied the electrokinetic behavior of hematite particles, before and after the interaction with the bacterial cells. The results revealed a shift of the isoelectric point (IEP) of the hematite after interaction with bacterial cells, suggesting a chemical adsorption mechanism. Moreover, after bacterial conditioning, the zeta potential curve of hematite presented high values in the alkaline pH range. The hematite and the bacterial surfaces presented contact angle values around 27.4° and 41.0°, respectively. According to the results, the B. subtilis strain was capable of modifying the hematite surface, and after interaction the hematite surface presented a contact angle value around 46.0°. The flotation tests were carried out in a modified Hallimond tube. The experiments revealed a significant increase in hematite flotability using the Gram-positive strain as bioreagent. The tests pointed out a maximum recovery of hematite in the presence of 600 mg/L and pH 5. Therefore, the results from this study showed the potential use of the B. subtilis strain as a biocollector for hematite flotation, and its possible application in the mineral flotation industry.

Jan 1, 2016

By Jean Robitaille

La découverte du gisement du puits Penna a nécessité une révision complète de tous les circuits du concentrateur Laronde pour permettre, premièrement, l?adaptation du procédé à la nouvelle minéralogie et deuxièmement, l'accroissement du tonnage de 1800* à 4500 t/j. Aux circuits existants de broyage, de flottation du cuivre, de cyanuration et du charbon en pulpe, les circuits suivants furent greffés : broyage semi-autogène, flottation du zinc, manutention des concentrés (épaississage, filtration, entreposage et chargement automatisé), décantation à contrecourant et précipitation au zinc, destruction des cyanures et remblai en pâte. Cet article se veut une revue des différentes étapes du projet d'agrandissement du concentrateur qui se sont effectuées par phases progressives de 1997 à 2000. De plus, une description des nouvelles technologies sélectionnées et implantées est présentée.

May 1, 2001

By Sergio Fuentes

During the past fifteen years, mines utilizing the block caving method have improved performance and systematically reduced total mining costs. This paper describes improvements in mine design, mine planning and mine management, including methods enabling the Chilean and International mining industry to ensure cost savings and productivity growth while using the block caving method. These improvements have encouraged the re-evaluation of underground operations at operating and closed open pits, and challenge surface mining applications as the only low cost mining method. This paper describes a strategy to estimate the optimum open pit to underground transition time during the life of a mine.

May 1, 2003

By Cheryl L. Allen

The power required to operate a ventilation system can be 25% to 50% of the total energy requirements of a mine. In an effort to reduce energy consumption, initiatives are being introduced at Vale Inco to increase the efficiency of ventilation systems with the objective of decreasing energy usage. One energy conservation measure being introduced is the use of variable frequency drive (VFD) technology for fan motor control. Advancement in technology is making VFD applications more of a standard in industry. The benefits include improved operating performance and system control, reduction in current peak demand, and optimized power usage. This paper describes the application of VFDs for main and auxiliary mine fans; and associated potential energy savings.

May 1, 2009

By J. Paraszczak

ABSTRACT: Application of teleoperated and automated (or “autonomous”) mobile equipment in under-ground metal mines represents a promising avenue for overcoming some of the challenges facing the industry. This paper addresses the overall effectiveness of autonomous loading and haulage equipment compared with conventional human-operated machines. Factors affecting availability, utilization, and production rate are explored, and an emphasis is placed on some problems and risks not present in conventional human-operated systems, as well as on the character and criticality of autonomous equipment. The need for a more in-depth analysis of factors affecting overall autonomous equipment effectiveness is stressed; these factors should be taken into consideration at the stage of feasibility studies. The paper concludes with recommendations and directions for future research.

Jan 1, 2010

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Apr 1, 2005

By Melissa Whellams

?? What is a social risk assessment (SRA)? ?? Why do a SRA? ?? When do you do a SRA? ?? How do you do a SRA? What is a social risk assessment? ?? SIA vs. SRA ? SIAs determine how a company?s project will affect social/cultural conditions in a region ? SRAs determine how social/cultural conditions will affect the risk profile of a company?s project Social risk context includes: ? review of human rights record ? analysis of conflict situation ? analysis of political climate ? stakeholder identification ? stakeholder concern/interest identification ? And so on?

May 1, 2008

Centralia?Mine Operations ?Centralia Mine ?Mountainous Terrain ?High rainfall (greater than 50 inches/yr) ?Multiple Pit/Multiple Seam ?Truck/Shovel Prestripping ?Dragline Overburden ?Coal Wash Plants

May 1, 2001

By Masatake Haruta

Gold can be deposited as nanoparticles on a variety of support materials by coprecipitation or deposition-precipitation of Au(OH)3, grafting of organo-gold complexes such as dimethyl-Au(III)-acetylacetonate, mixing of colloidal Au particles, and vacuum deposition. Owing to the moderate adsorption of at least one of reactants (for example, CO) on the edges and corners of Au nanoparticles and to the activation of the counter reactant (for example, O2) at the perimeter interface with the supports, supported Au nanoparticle catalysts exhibit unique and practically useful catalytic properties at relatively low temperature below 473K. They have already been commercially used for deodorizers in rest rooms in Japan and will find growing applications in indoor air quality control, pollutant emission control, production of hydrogen energy carrier, and innovations in chemical processes. Cluster science of Au may also open an exciting area of research showing some magic numbers for dramatic changes in reactivity.

Oct 1, 2003