Search Documents

By Robert Gannicott

??A mining company without the burden of operating a mine ??Management focused on marketing a high-quality, run-of-mine range of Canadian diamonds ??Robust revenue stream ??Specialist diamond knowledge ??Canadian exploration and development expertise ??BUT ??Single asset revenue base from depleting ore reserve ??Limited influence on production plans

Apr 1, 2005

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By I. R. Ward

"The need for energy conservation has been of increasing concern since the early 1970's, when the cost of petroleum based energy began to escalate rapidly and security of supply became uncertain. The cost of energy from alternative sources has also increased due to development costs and environmental restrictions.These developments have had a serious impact on the mining industry, which is energy intensive. The impact is magnified as lower grade ores are treated, and more energy is consumed per unit of product. In many cases increased operating cost is not compensated by the rise in product selling price.The magnitude of energy consumption in the mining industry is indicated by recent studies conducted in the U.S.A. and Canada. Based on 1970 figures, it was reported that the production of 1 ton of copper in the U.S.A. required 111. 8 x 106 BTU of energy, of which 60. 7 x 106 BTU (54.3%) was consumed in mining and processing (l)The survey of Canadian mills, conducted by CANMET and reported to the CMP meeting of 1978 (2), showed the following milling energy consumption figures (approximate averages):"

Jan 1, 1981

By Alain Bouchard, Germain Labonté, Jim Barrett

"Mill feed materials that are not run-of-mine ore are often a challenge for mineral processors and tend to accumulate in stockpiles, where they remain unprocessed for many years and become “slow moving inventories”. During a complete re-evaluation of the Clarabelle Mill operation (38,000 ton/day capacity) in 2000, it was concluded that there was an opportunity to assemble a 5,000 ton/day custom circuit to treat such stockpiles in the equipment that remained available during regularly scheduled maintenance shut-downs.This project was part of the larger Mill Redesign Project and involved testing the intended flowsheet under a number of operating scenarios for the first material to be treated: spent refractory bricks. The laboratory focus was on how to maximize returns using the available equipment and reagents.The circuit was successfully commissioned in the fall of 2000. As the brick stockpile was depleted, other potential feeds were evaluated at the laboratory, as well as in the new custom circuit itself. Processing of the spent refractory brick has yielded a significant contribution to the profitability of INCO. Significant opportunities lie ahead for generating more value from other slow moving inventories.INTRODUCTIONIntegrated mining operations tend to have slow moving inventories along the path from the mines to the finished products. Spent refractory bricks from furnaces and converters and furnace bottoms are materials that often end up in long-tern stockpiles. Such stockpiles are a challenge, although they represent small tonnages on an annual basis, because they are unique materials, which cannot be readily brought into the process at a rate anywhere near that at which they are produced, due to the high contents of deleterious components such as chromite or magnesia. Accumulation over years will eventually yield a metal inventory worthy of consideration given the right opportunity, such as availability of spare equipment or peak metal prices."

Jan 1, 2002

Conventional waste management practices produce two waste streams for the construction of separate disposal facilities. The design of tailings impoundments is usually controlled by physical stability. Waste rock materials offer high shear strength characteristics for waste dump construction, however the hydraulic properties promote oxidation. The problem of oxidation is significantly reduced for tailings due to a fine texture that augments water saturation. Co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retention capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimize acid generation and metal leaching. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repository. The results of a laboratory program to characterize the physical and hydraulic properties of Comix tailings and waste rock are presented here. Various ratios of tailings were blended with three distinct waste rock materials. The saturated hydraulic conductivity for the Co-mixed materials was found to vary between 2 x 10-7 m/s and 5 x 10-8 m/s depending on blend ratio, waste rock type and compaction. This paper introduces concepts for the co-disposal of tailings with waste rock and evaluates the hydraulic behaviour of a Co-Mix waste system. The potential benefits of Co-Mix are shown for a typical mine.

Nov 1, 2002

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By George Rice

Foreword Following the explosion in the Hillcrest mine, which occurred in the evening of Sunday, September 19th, 1926, and in which two men lost their lives, the writer was invited by the Hon. J.E. Brownlee, Premier of Alberta, to conduct an investigation into the causes of the disaster, and to make such recommendations as seemed advisable with a view to minimizing as far as possible the chance of future explosions in this and similar Alberta coal mines. Accordingly, the mine was visited, and extensive investigations were made underground on October 21st, 2.2.nd, and 25th, in company with Mr. John T. Stirling, Chief Inspector of Mines for Alberta, Mr. Moses Johnson, District Inspector for the Crowsnest Pass District, Mr. J as. A. Richards, Inspector of Mines, Edmonton, and also Mr. Thomas Davies, manager, and other officials of the Hillcrest mine. Hearings of the coroner's inquest were also attended on October 20th and 23rd, when testimony regarding the explosion was given by various witnesses. The following paper summarizes my general observations in tracing the place of origin of the explosion, and my efforts to determine the cause of ignition. Certain recommendations arc also made, and the writer invites discussion on these and the other matters dealt with in the paper.

Jan 1, 1928

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By J. P. Jarrell

Environmental considerations are of increasing importance in determining the acceptability, schedule and cost of expansion ofCanada's uranium processing industry. Environmental considerations must be addressed in the early stages of facility planning. This results in a dilemma, as the process data needed to predict physical environmental impacts are not yet available from process design activities. Hence, a business risk is incurred if plant design is carried forward to meet these requirements prior to project (or site) approval. On the other hand, project scheduling normally mitigates against leaving process design engineering until such time as project approval is obtained. This paper examines the experience gained in Eldorado Nuclear's proposed expansion of refining capacity as viewed by an environmental engineering consultant. The history of the project and the relationship to process design functions in the two-year period prior to the Port Granby environmental hearings are reviewed. During the Port Granby public hearing, there was a consensus that normal operation of the proposed refinery could be successfully integrated with the site's natural environmental constraints. Moreover, the radiological impact from plant operations was demonstrated to be inconsequential. However, concerns were raised relating to plant upset and accident situations. These concerns are summarized. Process data requirements identified during the environmental hearings are discussed. Finally, the concerns for on-site burial of radioactive waste are reviewed. These concerns focussed on long-term stability of the waste in the presence ofgroundwater transport, erosion and glaciers. The AECB's position on waste management with regard to this project is reviewed in light ofthe implications for design.

Jan 1, 1979

By F. Lindroos

A cornerstone in the LKAB Green Pellet concept is to produce pellets with a small footprint in terms of energy con-sumption, CO2 emission and emission of other elements harmful to the environment, like dust, sulphur dioxides, nitrogen oxides, chloride and fluorine. The concept also encompasses our determination to make pellet products that contribute to low environmental impact and low energy consumption in our customer?s processes. The presentation will focus on the pelletizing process. It will describe both how we have attempted to decrease the generation of unwanted components in the process gas, and how we have tested or evaluated equipment for external gas cleaning. We will discuss and give examples from recent and on-going efforts and outline some of the future challenges we see, to meet our own environmental standards and also the tough demands imposed by EU and national legislation, while striving to boost production.

May 1, 2011

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By Derek Ettie

"In the Hydrometallurgical processes, the presence of the so-called "crud" is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design.The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the series-connected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation.The transfer of the organic phase into the electrolysis cell can result in a "burnout" of the cathode. The carryover of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show.To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl® by this means, we can guarantee our customers the maximum possible solvent recovery and minimize the solvent costs in this process step. This system is presented in detail in this paper."

Jan 1, 2014

By N. I. Basuki, E. T. C. Spooner

"Abstract - More than 2800 published fluid inclusion data (primary inclusions) from eighteen typical Mississippi Valley-type (MVT) Zn-Pb deposits and districts were examined to study possible relationships between MVT fluid properties and metal tonnages and ore grades. The mean Th and salinity values for fifteen MVT deposits and districts are 122°C ± 21°C and 20.7 ± 2.6 wt% CaCl2 equivalent, respectively. In general, temperatures increase from pre-ore to ore stages, and salinities decrease from ore to post-ore stages. From post-ore to late calcite stages, salinity and temperature decrease with various trends within specific districts.Several conclusions are drawn: first, results show that Hanor’s (1996) salinity threshold for metalrich basinal fluids applies to typical MVT ore fluids (~16 wt% CaCl2 equivalent). Second, the lower limit of mean Th values of measured MVT deposits and districts (n = 15) of ~75°C is similar to Hanor’s (1996) observed temperature threshold for metal-rich basinal brines of ~60°C (n = 224). Third, there is no statistically significant relationship between fluid inclusion homogenization temperatures (Th) and metal tonnages or ore grades. Fourth, there seems to be a tendency for large tonnage districts/deposits to be associated with mean fluid salinities that are relatively low (~16 to 21 wt% CaCl2 equivalent) within the overall range of salinity means (~16 to 26 wt% CaCl2 equivalent). There is also a correlation between higher ore grades and higher salinities. Finally, comparison with other sedimentary rock-hosted Zn-Pb deposit types shows a trend of salinity decrease and temperature increase from MVT, sandstone-hosted and diapir-related Pb-Zn deposits, to vein-type and Irishtype Pb-Zn deposits, and then to sedex deposits. However, more data are needed for sedex deposits. The salinity threshold for significant Zn-Pb transport decreases to =~10 wt% CaCl2 equivalent at ~250°C. This study suggests that fluid inclusion analysis during exploration may be useful in assessing ore-forming potential (threshold salinity) and possible ore grades (salinity)."

Jan 1, 2002

By Richard Phiri, Mike Milupi, Jackson Kapobe, Anton Lemmer, Charles Mazala

Sustainability of plant operations in a rapidly changing mining environment requires a well-trained workforce to ensure smooth running of operations. To ensure availability of trained labor, Mopani Copper Mines PLC set up a training facility in 2013. The school offers training in Engineering, Mining and Process. The engineering section enrolls grade 12 school leavers for artisan training. Mining section offers comprehensive safety induction program to employees and contractors to meet the Mopani zero tolerance accidents safety policy. The process training section offers advanced training programs for plant operating personnel and university graduates. The program includes needs analysis, theoretical metallurgical modules, practical plant training and e-learning modules. The school also offers assaying and sampling courses. All the above courses are extended to individuals and other mining houses outside Mopani wishing to have their personnel trained. The Mopani sustainable development academy ensures that contractors engaged on the Mopani sites are fully registered, comply with all relevant regulations and have undergone induction program before they can be allowed to work on the mine. INTRODUCTION “Sustainable operation of the mining industry requires a continuous supply of trained human resources” (Kapobe et al., 2018). The publication by the Asian Development Bank (2014) argued that there was a mismatch between the demand for high-level skills and the oversupply of low-level skills. Globally, the mining industry requires continued supply of skilled manpower for its complex operations and long term projects whose sustainability is absolutely necessary. Implementation of newer technologies in plant operations to ensure cost effective and efficient operations requires trained and skilled labor at various levels to handle ever-changing challenges. Dutz (2007:152–156) made three recommendations for Building Worker and Management Skills in India: Strengthen enterprise - based training. The government should help ensure that the benefits of in- service training are widely recognized by enterprises, while simultaneously providing strong financial incentives Improve vocational training - Vocational education and training systems have been unsuccessful in preparing graduates to meet market needs, particularly because of a lack of interaction with industry. Public and private vocational education and training providers should be strengthened to make them more responsive to industry demands. Curricula should be updated to reflect modern technologies. Strengthen business, management education, management of research and commercialization - business and management education should be strengthened through public-private partnerships. Innovative management courses should be introduced. Although these recommendations were made for India, they also apply to Zambia and other low and medium income nations.

Jan 1, 2019

By Ryan W. Ulansky

This paper presents the conceptual design of a magnetically-levitated skip for use in an underground mine. A skip is used to move rock from an underground mine to its surface processing facility. Conventionally the skip is raised and lowered by cables, similar to an elevator. In a magnetically-levitated skip, the cable is replaced with a linear induction or synchronous motor to provide propulsion and levitation. Removal of the cables in a magnetically-levitated skip provides many advantages over a conventional system including the ability: to negotiate corners, to travel vertically in the shaft as well as horizontally to the mining face, and to move a very large volume of material using multiple skips in a small shaft. A magnetically-levitated skip is a safer, more environmentally-friendly, productive alternative to conventional skipping. It has the further advantage to decrease haulage distances for underground vehicles.

May 1, 2002

By S. W. Stogran

"A brief summary of the environmental testing and analyses required to ensure and maintain compliance of mining properties will be discussed. Programs for new and existing properties and for properties which may be purchased will be outlined and potential solutions to problems will be discussed. In addition to the compliance aspects of operations, due diligence will be discussed.1.0 INTRODUCTIONThe impact of mining projects on the environment is an area of major concern to the public, governmental agencies and mining companies. Due to the ever increasing pressure on the government by special interest groups and the public, governments have implemented legislation to control potential environmental impact of mining, from the exploration phase through to close-out. By not planning for environmental issues during all phases of a mining operation, unavoidable delays and retrofitted environmental programmes will be expensive and cause projects to be delayed, which, ultimately, may cause the abandonment of a mining prospect. Most jurisdictions require at least one full year of background environmental data. Therefore, many thousands of dollars are wasted as construction is interfered with or held up due to data collection. This may be avoided by a thousand dollars worth of sample being collected and analyzed early in the project."

Jan 1, 1992

By R. A. Leveille, M. D. Doggett

"Economic returns for the copper industry have been assessed by building cash flow models for each of the 100 new mines brought into production over the past 20 years. Ninety-one of the 100 new mines returned the assumed 8% cost of capital and generated a positive net present value (NPV) at the development decision point. Economic criteria for individual mines are highly variable with NPV ranging from -$111 million (-$111M) to +$3850M (all money values are presented in United States dollars) and internal rate of return (IRR) ranging from -8% to +95%. The copper industry collectively would generate approximately $39 billion dollars in NPV through the development of the 100 new mines.The returns to exploration ($174M per deposit) were measured by deducting the cost of exploration per deposit ($221M) from the returns to development per deposit ($395M). Overall, the copper business has provided positive returns to exploration. However, the variability in returns across deposits means that only 41 of the 100 new mines can carry the average cost of exploration. The long lead times and high costs associated with exploration result in only those deposits with large amounts of contained copper being able to cover the average finding cost of the industry.The returns to development and exploration are shown to be highly sensitive to the cost of capital and metal price assumptions. With respect to deposit type, porphyry deposits are both larger (NPV) and exhibit lower profitability (IRR) than the nonporphyry deposits. On a geographic basis, returns to development and exploration are higher in Chile than elsewhere, reflecting the larger average deposit size and lower average exploration cost per deposit."

Jan 1, 2009

By Don Thompson

Canada’s oil sands are a controversial topic and virtually every newsmaker and layperson seems to have an opinion about this 179 billion barrel resource. The oil sands represent 97 per cent of Canada’s remaining oil reserves, but misinterpretation and misrepresentation of the facts are threatening development of a resource that generates significant employment and tax revenue for Canadians. Join Don Thompson, president of the Oil Sands Developers Group, as he dispels the top ten myths about Canada’s oil sands and presents an alternative perspective on an industry that can play a critical role in North America’s economic recovery.

Jan 1, 2010

By J. Chlopas, D. J. Barratt, M. V. Sharp

"This paper describes the modifications made to the Fox Mine copper concentrate bin in order to obtain a continuous flow condition. The design of these modifications is based on test results obtained on Fox Mine concentrate using the flow factor testing machine in the research facilities of Cominco at Trail, B.C.The original design consisted of a cylindrical steel bin on a concrete slab with two slot-discharge openings. Based on predictions of the maximum mass flow hopper angle for conical and wedge shaped hoppers for the concentrate on various potential bin lining materials, Ultra-High Molecular Weight (UHMW) Polymer was selected as a liner.Using the recommended angles for conical and wedge shaped hoppers, the profile of the bin base was changed to suit the existing slot openings.The initial method of fastening the liner resulted in failure of the connections. Subsequent modification to the zinc concentrate bin fastener system proved satisfactory and it has now been in operation for over one year without any separation of the lining material.Utilization of flow testing procedures on concentrate samples has demonstrated that proper design of storage bins or hoppers to achieve continuous flow can be incorporated into the design of new plants."

Jan 1, 1978

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001