Search Documents

By J. H. . MORGAN

Talc-soapstone deposits exist in Patton Township of Quebec and have been mined by Bakertalc Inc. or its predecessors since 1938. The company produces products ranging from purified and micronized talc through to soapstone lumps. The deposits are found within serpentinite dykes and are zoned. Zoning grades from a serpentine core through zones of talcmagnesite, schistose talc and talc-chlorite schist be/ ore reaching the wall rock of quartz-sericite-chlorite schist. Talcmagnesite zones generally comprise 80 to 90% of the mined rock. The serpentinite dykes containing the talc probably were originally post-Ordovician peridotite of the same series that hosts the Eastern Townships asbestos deposits. Alteration of serpentine to talc-soapstone and magnesite apparently resulted through addition of silica and carbon dioxide along shears and fractures. Talc concentrations occur also at the intrusive contact between dykes and wall rock. The present Bakertalc Inc. operation at the Van Reel Mine is being worked from an inclined shaft 200 m below surface. The talc rock undergoes a variety of milling processes, depending on its particular market, be/ ore being bagged and shipped.

Jan 1, 1984

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By Tong Qin, Jinxia Zhang, Fusheng Niu, Limei Bai

"The interaction between a deformable bubble and a rigid particle in viscous liquids under microgravity conditions is studied by direct numerical simulation via an Arbitrary-Lagrangian-Eulerian (ALE) method. Due to the microgravity, the bubble will stay as a sphere in the fluid without external forces and its deformation is caused by the moving particle. In this study we assume the flow field is axisymmetric and the motion of the gas inside the bubble is neglected. The particle equations and the Navier-Stokes equations for the fluid are solved in a unified finite element framework. The particle obtains an impact velocity by an external force and the impact velocity is varied over a wide range. A ‘critical time scale’ T0 was identified for the interaction process. For successful contacts between particle and bubble, the time scale of their relative motion must be less than T0.INTRODUCTIONThe particle-bubble interaction is an important process in many applied industrial domains such as water treatment, froth flotation and liquid steel purification. It is a complex three phase process in that it embraces many research areas: fluid hydrodynamics, interfacial forces, particle and bubble behaviour and solution chemistry.Derjaguin and Dukhin(1961) clarified the particle-bubble interaction by introducing three-zone model for small and medium size particles. When the particle is far away from the bubble surface, the hydrodynamic forces are dominant. The particle is driven toward the bubble surface by the particle inertial and gravity. This region is regarded as Zone 1 and the interaction in this zone is a collision subprocess. As the particle gets close to the bubble, it exits a zone where the liquid flow around the bubble surface creates a tangential stream from the upper surface of the bubble toward the rear of the bubble. This is Zone 2 which is called the diffusiophoretic zone. In Zone 3, the particle is very closed to the bubble, surface forces like van der Waals, electrostatic and structural forces are considered. Contrast to Zone 1, Zone3 can be regarded as an attachment subprocess."

Jan 1, 2016

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By M. Fujikawa

The Kamioka Zinc Smelter was converted from the jarosite process to the goethite process in the year 2000. The reasons for the conversion of the process were that the silica content of the raw material increased and the iron content decreased. The silica easily turns to a gel in sulfuric acid solutions and this causes the solid-liquid separation characteristics to deteriorate. The basic behavior of silica in sulfuric acid solution was investigated and it was found that the goethite process is the most suitable to effectively separate and remove silica from solution. Furthermore, Fe has the capability to remove elements such as Ge that have an adverse effect on zinc electrolysis. This means that, when the Fe content of the raw material decreased, the impurity removal capability also decreased and there was a risk of a build-up of impurities in the process. Iron precipitates in many forms in sulfuric acid solutions. The capability to remove elements such as Ge differs depending on the compound precipitated. Goethite has a higher capability than jarosite to remove elements such as Ge. In this report, the results of applying the process established by investigations of the basic behavior of Fe, silica and Ge in the zinc refining plant are presented.

Jan 1, 2006

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

Gold recovery from refractory ores can be very difficult and complicated depending on the causes of the refractoriness. Typically, a fine wind and/or the oxidation of the gold-bearing sulfide minerals are required to liberate gold from the host rock matrix. Mineral separation techniques, particularly surface¬wettability based separation (i.e., flotation) and magnetic separation, can be used to pre-concentrate the gold and sulfide minerals, or to remove mineral species that are harmful either to the oxidation of the gold-bearing sulfides or to the cyanidation following the oxidation. In this paper, several processes are described, including oil-agglomeration flotation recovery of fine-grained gold and sulfide, reverse flotation of carbonate minerals prior to pressure or bio oxidation, reverse flotation of elemental sulfur after pressure or bio oxidation but prior to cyanide leaching, and magnetic concentration of gold-bearing iron oxides. The integration of these techniques with gold hydrometallurgical processes may make the economic recovery of gold from an otherwise uneconomic refractory ore possible.

Jan 1, 2011

By K. D. A. Whaley

Abstract -The Captain North Extension deposit consists of five sulfide lenses hosted in cherty and chloritic metasediment that is bounded by quartz-eye rhyolite and laminated rhyolite . Lens 2 consists of sphalerite and galena with silver-rich tetrahedrite in chert. Lens 3 contains massive pyrite, with chalcopyrite and minor gold, gradational to minor pyrite in a chloritic metasediment . The other lenses are unexplored. The sulfides occur as beds, fracture infills, and disseminated grains. Reserves are estimated at 207 555 tonnes grading 7.38% Zn, 2.76% Pb, and 91.81 g/t Ag. The deposit is isoclinally folded, dips steeply west, plunges 50 degrees south, and is faulted out to the north, where drag folding has reversed the plunge. Minor cross-faults contain talc and sericite. High sphalerite but low pyrite abundances result in poor responses to standard electromagnetic techniques. Lens 3, which contains more pyrite than Lens 2, responds better to induced polarization and allows detection. Geochemical anomalies are found in a nearby swamp and stream, but an impervious till cover inhibits the development of soil anomalies.

Jan 1, 1992

By T L. Horsley

The change from a seasonal to a continuous mining operation at Cassiar has been accompanied by increased emphasis on the preventive maintenance of mining equipment. This paper describes how equipment maintenance is organized, and details some maintenance practices that have proved advantageous to the Cassier operation. Introduction Cassiar Asbestos Corporation Limited is currenly carrying out an open-pit mining operation at the 6,300-foot elevation on McDame mountain in northern B. C. A 6-mile road connects the mine to the mill and plantsite at the 3,500-foot elevation. Ore concentrate is delivered to the mill via a 3llz-mile tramline. Naturally level ground does not exist in the mine area. The weather is typical of mountainous regions, exhibiting wide and rapid variations in temperature. It is generally wet and windy at the mine elevation, and a heavy snowfall is common. The rock types vary from a soft, sheared serpentine to massive serpentine, to medium-hard, friable sediments to hard, blocky volcanic flows.

Jan 1, 1964

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016

By Hans Lundberg

During the last few years, geophysical methods have been introduced to aid mining geologists and mining engineers in locating mineral deposits. These methods have been developed as the result of investigations of various physical characters of minerals and rocks. In prospecting for ore-bodies, electrical methods have proved most successful. These methods are based on the great differences in electrical properties, and especially in conductivity, between ore minerals and rock minerals. The electrical resistance of the common minerals, rocks, and ores in ohms per cubic céntimeter is given in the following table: [ ] The first attempts at electrical prospecting were based on observing currents of polarization around certain ore bodies, which currents it was possible to measure. This method has been developed by Prof. Schlumberger and has been utilized by him successfully. He is represented on this continent by Mr. Sherwin Kelly, who has successfully operated the method here.

Jan 1, 1926

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By Diego L. Romero, Joy P. Romero

"IntroductionMinerals may be classed broadly as ferromagnetic (magnetite for example), as paramagnetic (attracts to regions of magnetic field convergence) and as diamagnetic (attracts to regions of magnetic field divergence). High-intensity separators are not necessary to separate ferromagnetic minerals from other classes. Rather, low-intensity units that generate fields below 5000 gauss are adequate for this purpose. However, paramagnetic minerals, such as ilmenite, with high magnetic ""attractability"" require fields of up to 10 000 gauss; those with low attractability may require even higher fields. Table 1 shows approximate ranges of field intensities necessary to separate ferromagnetic and paramagnetic minerals from minerals of lower attractability, along with the force with which they are attracted relative to iron in a standardized magnetic field.Uniform magnetic fields, not useful for separators, are generated between flat parallel surfaces; non-uniform fields, useful for separators, arise when at least one of the surfaces is of irregular shape. The diagrams below show how magnetic lines of force align relative to north and south poles.If a particle is placed in a uniform field, it feels no displacing force unless the particle distorts the applied field assymmetrically. This is not the case in non-uniform fields which are required for magnetic separators.Magnetic fields can be generated by permanent magnets (low intensity), by electromagnets (medium and high intensity) and even by superconducting coils (100 000 gauss fields and higher), although the latter are not as yet useful in production environments .The magnetic force of attraction per unit of mass, that acts on a paramagnetic mineral such as hematite, increases in proportion to the strength of the field . Unfortunately, the highest fields attainable with electromagnets is of the order of 20 000 gauss. Fortunately, the gradient of the fie ld (that is, the degree of convergence of magnetic lines of force) is important, because the attractive force per unit mass is proportional to it also . This can be stated:"

Jan 1, 1989

By Heidi Fauser

The aim of the project was the development of an electroforming process for the production of medical implants out of gold. To prove the applicability of this technology, tympanostomy tubes were chosen as demonstrators. These barbell-shaped tubes are usually produced mechanically; of silicone or, for higher therapeutic demands, of metal ? gilded silver or gilded stainless steel. Gold electroforming of the tubes as an alternative manufacturing process would reduce the expenditures for the mechanical preparation and lower the corrosion susceptibility significantly. To obtain electroformed gold tubes of the desired shape, the following steps are necessary: fabrication of a negative template by drilling holes with countersinks in an insulated aluminium sheet, electroforming process, removal of the aluminium by using a sodiumhydroxide solution. For the optimisation of the shape and surface quality of the tubes respectively the simplification of the manufacturing process, various parameters were tested, e.g. aluminium quality and sheet thickness, type of insulation layer, substrate processing, hydrodynamic conditions, type of electroforming electrolyte, electrodes position, etc. The manufactured tubes were characterised in view of thickness distribution, hardness, surface roughness and purity in comparison to mechanically produced reference tubes. From the results obtained during the project it can be concluded that electroforming processes can be easily adopted for the manufacture of medical implants. The time-consuming electroforming process is by far compensated by the simultaneous production of an arbitrary number of implants.

Oct 1, 2003

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973

By B. P. Verma, K. N. Sinha, N. M. Raju, B. Singh

The paper describes a new method of grouting bolts developed at the Central Mining Research Station at Dhanbad in India. This method makes use of wire-mesh sleeve instead of the expensive metal tube to insert the cement mortar into the drill hole. The field trials confirmed that the method is cheap and an effective system of support.

Jan 1, 1972

By Ali Hashemi, Anna P. Perry

The PQ Deeps (PQD) is a production zone located at Newmont’s Musselwhite Mine in northern Ontario. Development started for the PQD in late 2017, and the first stopes were mined starting in early 2021. Unlike most historic longitudinal stoping of narrower orebodies at Musselwhite, the PQD is a wider orebody following the plunge of a fold hinge and is extracted primarily by transverse stoping. Some geotechnical challenges were experienced during early stoping efforts, necessitating design changes throughout late 2021 and early 2022 to optimize the stope design. This work describes the mining methods and design changes to transverse PQD stoping based on geotechnical lessons learned during early stoping efforts.

Jan 1, 2023