Search Documents

By J. Álvarez, J. Mesías, C. O. Gómez

"Operations routinely run flotation tests in laboratory mechanical cells to determine adjustments to plant operation based on feed flotation response or the effect of new reagents and dosages. The metallurgical results of these tests are certainly affected by changes in bubble size, which simultaneously impact the recoveries of the collection and froth zones. It is known that bubble size depends on the characteristics and operation of the machine in use, particularly on the gas flow rate delivered to the unit and the selected frother type and dosage. Although flotation rate constants have been related to bubble size, bubble surface area flux seems to be a more fitting variable to correlate flotation kinetics and cell performance, as it integrates bubble size and superficial gas velocity effects. However, although some evidence has been provided, a categorical relationship between cell recovery and bubble surface area flux has not been established. Our interest is to demonstrate this relationship to use it as a basis for developing soft sensors to track on-line collection zone recovery in cells. Flotation tests were designed to produce Cu concentrates for a range of bubble surface area flux values, obtained through changes in frother concentration at a constant gas flow rate, and by increasing gas flow rate at the same frother concentration. The tests were run on samples prepared from an ore batch supplied by a local operation, following strict grinding and flotation procedures, with a shallow froth to approximate cell recovery to that in the collection zone. Bubble sizes were determined using the sampling-for-imaging technique developed at McGill. The results unequivocally showed a consistent positive correlation between cell recovery and bubble surface area flux, and significant variations in performance when frother addition and gas flow rate were changed.INTRODUCTIONMineral flotation is a separation process to produce concentrates of valuable minerals by selective attachment of particles to the surface of bubbles. The process is carried out in machines where air is injected through a mineral pulp to form bubbles, and operated to create two zones: a bottom one (collection zone) where bubbles are continuously generated under conditions adequate to form bubble-particle aggregates by collision of the rising bubbles with suspended particles; and a top one (froth zone) where bubbles and bubble-particle aggregates continue to rise while concentrating and forming a froth layer for water and entrained particles to drain back to the collection zone, before overflowing as a concentrate stream. The phenomena occurring in these zones are complex and, in many cases, interactive, as they simultaneously affect stages of the particle separation sequence occurring in both zones. Although there have been significant advances in instrumentation to characterize particle and bubble populations, these have not resulted in knowledge to explain or models to describe phenomena from fundamental principles. Measurements continue to be limited to the development of empirical models for predicting the effect of operating variables on performance."

Jan 1, 2016

By Z. Zhao, B. Li

"Fractures are the key channels for fluid flow and mass transport in fractured rocks of low/negligible matrix permeability. In single rock fractures, surface roughness causes fluid flow in tortuous paths, and reduces the overall fracture conductance. A number of empirical models have been proposed to relate the reduced hydraulic aperture to the mechanical aperture due to surface roughness, which were revisited and compared. Using two of those relationships between hydraulic apertures and mechanical apertures, we studied the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks. The results show that fracture roughness can affect the flow rates and residence time to varying extent, mainly depending on the empirical models between hydraulic apertures and mechanical apertures. However, fracture roughness has negligible influences on the general patterns of fluid flow (channeling) and solute migration (e.g., travel paths and shape of breakthrough curves). This is because the connectivity of a fracture network is mainly determined by other geometrical parameters (fracture positions, orientations, and lengths), rather than roughness or apertures. INTRODUCTIONIn fractured crystalline rocks of low or negligible matrix permeability, fluid flow and contaminant migration mainly occur within the connected fractures. An understanding of fluid flow and contaminant migration in fractured rocks is a crucial issue in many deep underground projects, e.g. underground repositories for radioactive waste, CO2 sequestration, enhanced geothermal systems, oil and gas production, etc. Rock fractures are typically rough-walled, and surface roughness appears to have first order control on the mechanical and hydraulic behavior of single rock fractures (Boutt et al., 2006).It is well known that the mechanical aperture of a rock fracture is usually larger than its hydraulic aperture, due to fracture surface roughness (Tsang and Witherspoon, 1983). However, for naturally fractured rocks including numerous discontinuities, the effects of this reduced hydraulic aperture in local fractures on macroscopic fluid flow and solute transport in complex fracture systems still remain unclear. Many previous studies assumed identical hydraulic and mechanical apertures in discrete fracture network models for simplicity (Min et al., 2004; Zhao et al., 2011). Therefore, the main objective of this study is to evaluate the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks, by employing the empirical models that relate the hydraulic aperture to the mechanical aperture."

Jan 1, 2015

By Gary M. Bone

The autonomous control of vehicles interacting forcibly with their environment, such as dozers and tractors, is an unsolved and challenging problem. Forces and motions are inherently coupled between the tool and the means of vehicle propulsion. Furthermore, they are often operated within uncertain and unstructured environments, such as those encountered in underground mining. There is a growing industrial interest in the development of robotic vehicles to improve productivity, efficiency and safety in mining and construction. This paper focuses on the modeling and control of autonomous robotic dozing for a material removal operation. A dozing process model has been developed based on observations of both a fullscale dozer and a scaled-down version. The model characterizes the dynamic interactions between the blade position, material accumulation on the blade, material distribution in the environment, and the motions of the dozer. The dozing control objective is to remove the loose material as rapidly as possible by driving forwards at full power while automatically raising/lowering the blade in response to sensor measurements. Two different controllers were developed to meet this objective. The first controller is based on a set of heuristic rules, and the second is an optimal controller based on the dynamic model. An instrumented scaled-down robotic dozer and dozing environment, designed to emulate the full-scale operation, are used to implement the controllers and compare their performances over multiple dozing passes. Experimental results are presented showing that the model-based controller increased the material removal rate by 33% compared to the rule-based controller. Lastly, technologies for full-scale implementation are discussed, followed by proposed future work and conclusions.

Aug 1, 2013

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By Samuel Nunoo

Gibraltar Mine is an open pit copper-molybdenum mine in central British Columbia. The stability and potential failure modes of pit walls in the Granite Pit are controlled by the orientations of joints and faults. The structural geology also has an impact on as-mined bench geometries. Geotechnical mapping and surveying were conducted using stereo photographs and photogrammetry software. Detailed digital terrain models were constructed to determine the pit wall geometry and the locations and orientations of larger structural features. The pit wall geometry is compared to conventional survey results and the mapped structures are compared to results from a nearby geotechnical borehole.

Aug 1, 2013

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By J. I. Jr. Moore

Many articles have been written about the various operations of Britannia mines and mill, as well as treatises on the geology and ore deposits. A partial list of these papers is given below. Most of these papers have covered well the history of Britannia, and have included a thorough discussion of the geology and ore deposits; therefore, in this paper, no account of these subjects. is necessary. However, a short description of the ore deposits will be given as an aid to a clear understanding of the descriptions of the various mining methods. The Ore Deposits The ore deposits at Britannia occur along a shear zone and are five in number, named for the claims in which they lie, as follows: Jane, Bluff, Fairview, Empress, and Victoria. Each of these deposits is called a mine, as they are separated by 500 to 1,000 feet of barren ground. The Jane mine, although the first producer of the Britannia group, has not been in operation for a number of years. The deposit is a silicified replacement in sediments; with very little evidence of shearing. The Bluff deposit is a highly silicified replacement in porphyry, massive and irregular, very hard in the upper 600 feet with practically no shearing, and softer within chlorite schist in its lower 1,000 feet . The Fairview deposit consists of a series of twelve distinct veins or lodes, rather lenticular in shape, and occasionally merging.

Jan 1, 1928

By Gerald Sanders

Presentation Topics ? We?re Going to the Moon Again? ? What is Lunar Mining ? In-Situ Resource Utilization? ? What Are The Challenges to Lunar Mining? ? What is NASA Currently Doing?

May 1, 2009

By P. J. Finnis

This paper describes the use of wire rope on open-pit mining equipment, giving specifications and examples of the performance achieved. Installation methods are also discussed, making the paper of considerable practical use to mine operators.

Jan 1, 1973

By Walker. P. W. A.

Abstract -The Riviera tungsten occurrence in the Cape Province of South Africa was discovered in October 1979 as a result of stream-sediment panned concentrate sampling. The Cape age granite and late Precambrian Malmesbury Group carbonates and chlorite schists which it intrudes and which host the mineralization are covered by between 10 m and 30 m of Tertiary/Recent alluvium and clay. The scheelite/powellite and molybdenite mineralization occurs in a greisenized granite cupola with an overprint of porphyry-type alteration as well as in minor skarns. The ore reserve is estimated to be 46 million tonnes at an average grade of 0.2160Jo W03 and 0.020% Mo. The deposit is uneconomic at current tungsten prices.

Jan 1, 1994

By S. Kobayashi, N. Ohara, T. Aoki, S. Sakurai, M. Iwano, M. Shimo, I. Otsuka

"This project is the upgrading of a commuter line of approximately 76 km to improve the railway system in Istanbul metropolitan area. Railway tracks have been connected between Asia and Europe through a tunnel under the Bosphorus Strait. The length of these underground structures sums up 13.6 km. In this paper, the observational construction management based on field measurement performed at large scale underground railway station (Sirkeci station) constructed by means of New Austrian Tunneling Method (NATM) is described and the mechanism for generation of ground surface settlement above this station is discussed.Buildings above Sirkeci station are overcrowded. About 60% of the buildings are made of reinforced-concrete (RC) and others are of brick. Based on the investigation into the predicted settlement and inclination, necessary actions such as structural reinforcement and soil improvement have been conducted for dilapidated buildings.Rock mass around Sirkeci station consists of alternative strata of sandstone and mudstone. It is overall soft rock with an elastic modulus of 150 MPa, partly including fractured zones. Overburden is about 30 to 40 m. The thickness of unconsolidated sand layer distributed on the bedrock is about 10 m. As a result of in-situ permeability tests, the coefficient of permeability of the sand layer is about 1.0x10-3 cm/s. Fill layer of about 10 to 25 m in thickness covers the sand layer at the ground surface. The fill layer contains a lot of artificial waste like splinters of wood, brick chips and mortar chips, etc. in addition to gravel, sand, silt and shells. The coefficient of permeability of fill layer is estimated to be 1.0 x10-2 cm/s, which is one-order greater than that of the sand layer. Fill layer consists of ancient city ruins of ages respectively from the Eastern Roman Empire, the Byzantine Empire and the Ottoman Empire and has a lot of gaps.The underground part of the Sirkeci station was excavated through a ventilation shaft. Ground surface settlement occurred more than predicted. Therefore, back analyses were performed in order to precisely predict the next-step settlement. However, back analyses with elasto-plastic models could not simulate the actual phenomena and hence, an anisotropic-damage-parameter model developed by Sakurai (1999) was adopted for the back analysis. Furthermore, as the excavation of tunnel proceeded, the ground surface settlement exceeded the predicted value again. Based on the monitoring results, it seemed that pore water pressure decreased by the tunnel excavation resulted in the soft rock and soil to be contracted due to the increase in the effective confining pressure. A coupled hydraulic-mechanical analysis was applied to explain the relationship between decreased pore water pressure and ground surface settlement. The settlement due to drainage from tunnel wall was well-estimated in the coupled hydraulic-mechanical analysis.However, further settlement occurred more than predicted again and again. Though it was very difficult to clarify the reason of the large settlement, it was recognized that the unexpected ground surface settlement resulted from the existence of the large gaps in the fill layer that was greatly compressed. The final settlement reached up to 327 mm."

Jan 1, 2015

By M. A. Vos

"Aggregates are the low-cost mineral raw material of building construction. Large volumes of aggregate are consumed each year. The availability of aggregates in southern Ontario is discussed in the context of the geological formations in which they occur. Sand and gravel are abundant in glacial deposits and in recent sediments. A knowledge of the glacial history is important for their discovery. Bedrock formations provide a variety of aggregates in Ontario. Knowledge of the rock types involved and of the depth of overburden are important for evaluation of the aggregate potential of bedrock resources in an area. Utilization of available resources intensifies as the population increases. Urban development makes it progressively more difficult to satisfy the demands of the construction industry. The effects of urban development on the aggregate resource base of an area are illustrated by developments and consumption statistics in the Toronto- centred region. There is an obvious need for a comprehensive survey of available resources in urban areas to serve as a guide in land-use planning. To fill this need, staff members of the Industrial Minerals Section, Geological Branch, Ontario Department of Mines and Northern Affairs, are engaged in mapping projects and mineral resource studies in southern Ontario as well as in some urban areas of northern Ontario."

Jan 1, 1972

By Gordon Nelson

The Homestake gold mine is one of the largest and oldest continuously operating gold mines in orth Ame rica. To date this mine has produced in excess of 128.000.000 tons of ore containing almost 34 million ounces of gold . Gold mine ralization is restricted to the Homestake Formation. This unit is a metamorphosed iron-formation which is enclosed by pellitic metasedime nts below (Poorman Formation) and a pellitic to qua rt zitic unit (Elli son Formation) above. The e ntire Precambrian sequence. in the Lead area. has been subjected to a multi-stage defo rmation episode which ha c reated an extremely complex structural setting for the Homestake orebodies. Metamorphic grade inc reases from greenschi st ro amphibolite in a northeast d irecti on acros the mine area. Present thickness of the Home take fo rmation va ric from O to »400 fee t. The amount of thicke ning and th inning which is attributable to tectonic deformation or original sedimenta ry di fferences is not known. Orebodies constitute onl y a small pe rcentage of the Homestake Formation and do not occur along a pa rticul ar stratigraphic pos ition within the unit. Gold i assoc iated with inc reased py rrhotite and a rsenopyrite concentrations within the iron formation. Inc reased \ cin qua rt z development and chl oritic alteration usuall y accompany this minerali zation. Local remobilizati on of mine ralization due to metamorphi sm has occurred. Homestake mine ralization has been shown to be of sy ngeneti c origin . Because no feeder zones have yet been recognized a di stal source for the mine ralization is inferred .

Jan 1, 1986

By A. Monballiu, J. A. Martens, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, B. Meesschaert

In this work, bioleaching of non-sulphidic materials by applying chemoheterotrophic bacteria and fungi is studied. It was found that the tested fungus, Aspergillus niger, leached substantially more nickel from olivine than the tested bacterium, Bacillus mucilaginosus. A. niger also outperformed fungal species Humicola grisae and Penicillium chrysogenum in the leaching of olivine. Contrary to traditional acid leaching, the microorganisms leached nickel preferentially over magnesium and iron. On average, a selectivity factor of 2.2 was achieved for nickel compared to iron. This can potentially facilitate postprocessing of the leach liquor and reduce the cost. The impact of ultrasonic conditioning on bioleaching was also tested, and substantial increase in nickel extraction with A. niger was observed. This was credited to an increase in the fungal growth rate, the promotion of particle degradation, and the detachment of the stagnant biofilm around the particles. Furthermore, ultrasonic conditioning enhanced the selectivity of A. niger for nickel, resulting in a selectivity ratio for Ni/Fe equal to 3.5. The chemical resistance of the selected microorganisms to several heavy metal and metalloid (As(III,V), Cd, Cr(III,V), Ni, Pb, Zn) was evaluated. It was found that, with the exception of As(v) and Cd, A. niger has high tolerance to these components. Therefore, this biohydrometallurgical route can potentially be applied to non-sulphidic wastederived materials, such as industrial slags, ashes and sludges.

Jan 1, 2014

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By W. J. Gibson

"This paper will provide a general assessment of the differences in construction and industrial labour relations. From this outline will come a detailed examination of labour relations in the construction industry and then specifically as related to the construction of mining projects, with emphasis on projects in isolated areas. Development of manpower forecasts, manpower availability, wage escalation formats, working rules, training and recruitment programs, and safety - as related to construction labour relations in the mining industry - are topics which will be dealt with."

Jan 1, 1972

By J. Béland

"Three stages, each characterized by a particular sedimentation, magmatism, mineralization and deformation, are recognized in the geological history of Gaspe. The first stage led to the formation of the Taconian orogen, the second to that of the Acadian orogen and the third stage to the accumulation of a post-orogenic cover. The Taconian orogen includes volcanic and detrital rocks of Late Precambrian or Cambrian and Lower to Middle Ordovician ages in which ultrabasic intrusions have been emplaced. Folding is severe. Mineralization is of the Cr-Ni-Cu type, related to the igneous facies.The rocks constituting the Acadian orogen include two distinctive sequences corresponding to two successive sub-stages. The second substage began in Early Devonian time with the first pulses of the Acadian orogeny. The rocks of the first substage grade southward from a nearly platformal sequence to an assemblage implying less stability and spotty volcanism. The second substage was one of synorogenic deposition of elastic rocks, first in a marine environment and later under terrestrial conditions. Granitic intrusions, surrounded by aureoles of skarn and hornfels in which Cu-Pb-Zn mineralization is found, accompanied the Acadian deformation. The second-stage"

Jan 1, 1969

By J. Bardinas

"The use of autogenous mills has become widespread, owing to their capacity and favorable capital and operating costs. Optimal operation of these systems is critical, given their high energy consumption and effect on downstream processing. A considerable effort has been spent over the years in the development of advanced control systems to achieve a better performance in this regard. However, despite significant advances, the problem still remains challenging, owing to the nonlinear behaviour of the system with respect to the mill variables, and, the unmeasured ore variability come from the mine.The mill load, in particular, can be seen as a state variable of the mill, which could be important for; modelling and control, and, important insights into the mill behaviour. In this investigation, time series cluster analysis was performed using online mill load measurements in order to identify the different control states of the mill. More specifically, this time series was divided into short non-overlapping segments. A distance matrix was set up for each segment and the information was captured by means of textural features, similar to that used in multivariate image analysis. These wavelet and grey level cooccurrence matrix features could subsequently be used to rapidly identify the normal operating conditions from the feed disturbances in the mill.In principle, the methods and models presented here, once suitably validated and calibrated, could be used in online process monitoring of autogenous mills. They also could serve as a foundation for developing more advanced process control models."

Jan 1, 2016

By J. A. Finch, R. R. Cunningham

The amount of foam volume generated in relation to the gas flowrate has long been used to define the foaminess of a solution and to characterize surfactants. The vessel geometry and gas flowrate range can affect the foam volume results. A fixed area column was tested alongside a variable area conical vessel with two surfactants. It was found that the fixed area vessel will cause foam volume to expand or contract which masks the effect of the surfactant. The conical vessel showed two regimes of foam volume production dependant on gas flowrate. The low gas flowrate regime revealed the physiochemical nature of the surfactant while a high gas flowrate revealed kinematic properties. Foaming properties of a surfactant is best determined with a variable area vessel at low gas flowrate.

Jan 1, 2009