Search Documents

By Harold N. Miller

Lost time and services caused by electrical equipment breakdown or cable faults can often be substantially reduced by the use of direct-current high-voltage testing as a maintenance tool. This paper discusses the relative merits of alternating-current versus direct-current testing, pointing out the advantages in size and cost of equipment and more definitive results achieved through the use of D.C. General principles of direct-current high-volt-age testing, types of testing, methods of performing the actual test and interpreting the results are explained. ?The value of insulation resistance measurements and their relationship to high-voltage testing is discussed. Pinpointing the physical location of a cable defect using a fault locator or thumper is described. Reference is made to several organizations that have effected considerable savings with high-voltage test programs. Introduction T HE past decades have seen great advances in the field of electrical power distribution and application. Motor generators, power-operated equipment, cables, etc., have all gone through various stages of improvement both in efficiency and reliability. Un-fortunately, however, power failures and equipment breakdown still occur -frequently with disastrous effects in loss of time,

Jan 1, 1965

By E. V. Konopleva, H. J. McQueen

"The isothermal bainite transformation kinetics of low- and medium-carbon alloy steels after hot deformation and the rmocycling treatment (TC) has been studied by the magneto - metric method. Deformation was produced by rolling at 800°C-1000°C. TC included three cycles of rapid (30°C/s) electro-heating up to 900°C-1000°C followed by quenching.Hot deformation retards bainite transformation in the lower part of bainite range (<400°C) and accelerates it in the upper part (>400°C). The effect is greater for higher strain and lower deformation temperature. Deformation also diminishes the overall bainite fraction below 400°C and increases the completeness of reaction above 400°C.Thermocycling provides more uniform ultrafine austenite grains with average size of 3 µm -4 µm compared to 12 µm -14 µm after conventional heating. The transformation rate after TC was almost the same as after conventional heating in low-carbon steel but was faster in medium-carbon with no change in the completeness of reaction. The degree of acceleration increased with rise of transformation temperature.There are a number of factors which are responsible for a change in bainite transformation kinetics in austenite deformed at high temperatures or subjected to TC. One of the most important factors is the refinement of structure, another one is structural and chemical inhomogenity of austenite due to deformation or to rapid heating. To estimate the contribution of these factors, ?-transformation was studied after different austenitizing conditions (low-temperature heating at 850°C- 950°C; high-temperature heating at 1100°C; step treatment – austenitizing at 1100°C, then cooling to 950°C-850°C). The results obtained make it possible to conclude that the structural and chemical inhomogeneity of austenite activate the bainite reaction while the grain refinement retards it. Intensity of the effect produced by each factor depends strongly on the steel composition."

Jan 1, 1997

By M. B. McClenaghan

"The Matheson area of northeastern Ontario is of great interest for mineral exploration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has become an important exploration method. The Ontario Geological Survey&apos;s Black River-Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift (< 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (> 3.3 S.G.) and fine (- 250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (< 50 um) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of = 3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By Bruce C. Fielder

"The concentration of uranium in orebodies discovered in the Athabasca Basin of northern Saskatchewan over the last 20 years has increased by a factor of 100. These high grade uranium orebodies are associated with high concentrations of radionuclides, complex mineralogy and an elemental makeup that includes base metals, arsenic, and molybdenum. Exploiting these high grade ores has required metallurgical advances in milling, tailings disposal and effluent treatment as well as changes in the design of uranium mills.This paper describes the most significant advances, including advances in dealing with the environmental issues which have become more prevalent in recent years. The milling processes of the Cluff Lake Mill, Key Lake Mill, Rabbit Lake Mill, and McClean Lake Mill are compared to illustrate both similarities and differences necessary for milling different orebodies.BackgroundUranium mining in Saskatchewan started in 1953 when the Beaverlodge Mine, owned by Eldorado Nuclear Limited (Eldorado), came into operation at Uranium City. Development in the Athabasca basin started in 1975 when the Rabbit Lake mine came into operation. This was followed by the start-up of the Cluff Lake mine in 1980 and the Key Lake mine in 1983. The McClean Lake mine is forecast to start up in the near future. The McArthur River mine recently received construction approval and the Cigar Lake Project and the Midwest Project are currently in the environmental approval process.The Beaverlodge operation ceased production in June 1982 after nearly 30 years of operation. The Rabbit Lake mill processed Rabbit Lake ore from 1975 until 1985, Collins Bay R-Zone ore from 1985 until 1993, and is currently processing ore from the Eagle Point mine (Bharadwaj, Jarvi and Lam, 1996). The Cluff Lake mill processed ore from the D- Orebody from 1980 until 1984. Since then the Claude orebody has been processed and the OP and DS orebodies are presently being milled (SRK. Senes and Melis, 1987; and Cogema Resources Inc. 1994 ). The Key Lake mill processed ore from the Gaertner ore body from 1983 until 1989 and Deilmann ore has been processed since (Cameco Corporation, 1992b and I 994a). Processing of McArthur River ore in the Key Lake mill is scheduled for 1999. The McClean Lake mill will be processing ore from the JLR, Sue and McClcan orebodies associated with the McClean Lake mine. In future ore from the Cigar Lake and Midwest projects will be processed in the McClean Lake mill. (Minatco Limited. 1991a)."

Jan 1, 1998

By S. Jeon, T. H. Kim

"Understanding the frictional properties of discontinuities is crucial to ensure the stability of underground structures. In particular, the frictional behavior at depth depends on the complex interaction among mechanical, hydrological, thermal and chemical characteristics and their coupled effects. In this study, a series of triaxial compression tests were carried out to investigate the behavior of rough shear surface of synthetic rocks. The frictional behavior showed little variation at different confining and water pressures. The test results were analyzed using Coulomb’s failure criterion. In addition, numerical analysis was carried out using PFC2D to simulate the test.INTRODUCTIONUnderstanding coupled behavior of rock at depth is of great importance in design, construction and operation of underground structures such as a disposal facility of radioactive waste, hot dry rock geothermal system and oil reservoir. In particular, many uncertainties are involved in characterizing deep rock mass deformation in the designing process and interactions among fluid flow of groundwater, high temperature and stress disturbance should be considered. Many independent studies have been carried out to investigate the thermal, hydro, mechanical and chemical coupled effects in numerical and experimental methods. They include the researches by Lockner, Summers, Moore and Byerlee (1982), Jafari, Amini Hosseini, Pellet, Boulon and Buzzi (2003), Tembe, Lockner and Wong (2010), Lee, Lee and Jeon (2012), Indraratna, Premadasa, Brown, Gens and Heitor (2014)."

Jan 1, 2015

By G. W. R. Kuzyk

"Hydraulic drills, recently implemented at the Tantalum Mining Corporation of Canada, Limited, Bernie Lake Mine, are proving to be an economic alternative to pneumatic drilling systems. The paper describes the application of an electric-hydraulic drill jumbo to the mechanized room-and-pillar mine and its performance. The application of these drills resulted in improved environmental and working conditions.Drill rods and bits are a major cost centre in hard-rock mining applications. The paper also discusses the performance of one manufacturer&apos;s product used on the hydraulic drills.IntroductionThe Tantalum Mining Corporation of Canada, Limited (TANCO) started producing tantalum ore from its Bernie Lake pegmatite in 1969. The pegmatite, encased in amphibolite, is shallow seated and flat lying. It is defined by diamond drilling along 4,000 feet of strike and 1,500 feet down dip, ranging in thickness from 60 to 280 feet. Relatively well defined zones of mineralization occur within the pegmatite and form separate orebodies of tantalum, lithium and cesium."

Jan 1, 1981

By John H. Walsh

"ForewordThis paper is to be published in two parts in succeeding issues of the CIM Bulletin. In Part I, the problem of global climate change is explored together with a summary of the government&apos;s present policy in this field. Implications for the steel industry are examined as are possible strategic responses. Part II of the paper will present a new possibility - the joint production of iron and liquid fuels useful for transportation purposes. In the joint production case, the objective is to use carbon for more than one purpose in what might be termed a &apos;carbon cascading&apos; technique. ABSTRACTIt is becoming increasingly probable that emissions of carbon dioxide from the fossil fuels will have to be reduced to deal with the threat of global warming. This issue is likely to be resolved one way or the other in the period 1995 to 2000 which does not leave much time to develop responsive options. In the intervening period, the policy of the Government of Canada is to stabilize emissions of greenhouse gases at their 1990 level by 2000, by encouraging greater efficiency in the use of energy. Should further reductions prove necessary, economic instruments would probably be employed but these would not be applied before a comprehensive international agreement is reached.There are three main themes in this paper: it is assumed that measures to control carbon dioxide emissions will in fact be necessary by the tum of the century; that there will be a rising need for liquid fuels to supply the world&apos;s steadily growing fleet of motor vehicles for many years to come, and that the future niche for Canada &apos;s industry in such a carbon-constrained world will be the operation of the energy-intensive industries with efficiency and environmental sensitivity.The steel industry, as a large user of both coal and energy in other forms, would be significantly affected by a need to reduce carbon dioxide emissions. This paper first examines what might be called the conventional responses open to the industry in such a situation and then explores a new possibility for making better use of carbon by the co-production of iron and liquid fuels."

Jan 1, 1992

By John A. Herbst, Gerald H. Luttrell, Jaisen N. Kohmuench, Aaron Noble, Michael J. Mankosa

The HydroFloat TM is an innovative fluidized-bed separator that can substantially increase the upper particle size that can be successfully treated by flotation. Recent studies conducted using laboratory, bench-scale and pilot-scale equipment indicate that this technology can be used to float coarse sulfide middlings that cannot be recovered by conventional flotation machines. Recent data collected from pilotscale tests conducted at a base metal concentrator indicate that this technology can float middlings particles as large as 850 microns in diameter containing as little as 1% exposed hydrophobic mineral. As such, the crossover of this technology into the base metals industry has the potential to substantially reduce grinding costs and increase concentrator recovery/capacity through the use of split-feed circuitry. The split-feed concept, which is often used for upgrading industrial minerals, involves segregation of the feed into more than one size class followed by subsequent upgrading using mills/separators/reagents specifically optimized for each size class. In this article, a split-feed circuit is described that utilizes two stages of classifying cyclones in conjunction with the HydroFloat_ separator. The circuit is designed to recover, recycle and regrind coarse middlings containing small amounts of valuable mineral while simultaneously rejecting coarse well-liberated siliceous gangue so that mill throughput can be increased. Simulation data conducted using well-known process models suggest that this approach can increase existing primary mill capacity by up to 25% with only modest investments in new classifying and flotation equipment.

Jan 1, 2016

By P. R. Geoffroy

Extensive and Intensive Prospecting As often pointed out, the search for new ore deposits may be carried on along two widely divergent lines. It may be either extensive or intensive. By extensive prospecting we mean a search for mineralized outcrops conducted over large and more or less virgin tracts of land, followed by a test of the practical value of any discovery made, the test being limited to the immediate vicinity of the outcrop. Extensive prospecting, was, in fact, the only policy known to the early prospectors. of the American continent and is still the rule in the remote sections of the Canadian Shield and in the African wilderness. It can be further characterized by the lack of emphasis placed on geological and other technical means as an aid to the search for ore. However, very little virgin ground is left, nowadays, for a man or a company to test their luck, and whatever is left is so remote from the necessary means of development that any new discovery will require considerable delay and expenditures to be amenable to profitable mining. On the other band, a great many of the favourable and still unexplored areas (and this is particularly true in Canada) are overburdened to such an extent that outcrops of bed-rock are extremely scarce and extensive prospecting is nearly impossible. Intensive prospecting, to the contrary, must be understood as a detailed search for ore carried on over limited areas in districts already known to be mineralized and covering regional structures whose relation to mineral deposits bas been estahlis.hed with a fair degree ot certainty. The search for deep-seated deposits in the vicinity of successful mines is a perfect example of intensive prospecting. As a matter of fact, the majority of the geologists employed by the mining industry are engaged in some kind of intensive prospecting.

Jan 1, 1950

By Louis M. Perlman

CAN PRESENT TRENDS CONTINUE? Can population growth in the world keep going at the average rates of the last few decades, till, say, the year 2000? And beyond? At the same time, can we expect steady increases in mineral consumption per head, all over the world, as the living standards of many nations converge toward the living standards of North America? If they do converge? Does the total fund of world resources extend, with foreseeable techniques, to supplying the consequent demands for metals, non-metallic minerals and energy? Do we have the requisite economic and scientific techniques available to answer these questions? Certainly, we cannot forecast over decades with any certainty. There are many, of course, who seem to believe that by the simple fitting of trends, they can tell us something about the world and resource constraints in the year 2000, twenty-three years from now. It is significant that many studies of this sort have added sustenance to the &apos;doom-watching&apos; fraternity of commentators. The reason is simple. The extrapolation of exponential trends into the distant future frequently leads to the most astounding and impossible scenarios. Another feature of exponential growth is the suddenness with which certain fixed limits are approached. It took world population two hundreds years to increase by 1/2 a billion, from 1650 to 1850. Yet some U.N. estimates suggest that the net addition to human population will be over 2 billion between now and the end of the century. Thus, the present world population would increase from a little under four thousand million today to rather over six thousand million in the year 2000.

Jan 1, 1977

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By S. A. G. Poppen, J. Konopka

"Petro-Canada&apos;s project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By T. J. Wells

THE blast furnace is the base of the steel industry, since there is no commercially practical way of converting iron ore directly into steel. In three hundred years, the blast furnace has developed from a small unit using charcoal as fuel and producing about one ton of iron in twenty-four hours to a furnace making upwards of 1,500 tons a day. The principle of the blast furnace is briefly this: A descending column of stock, consisting of ore, fuel, and flux, is met by an ascending stream of gases, consisting in part of gases formed by the combustion of the fuel and in part of pre-heated air which is blown into the lower part of the furnace. The flux combines with the impurities in the ore and the ash in the fuel to form slag, which is drawn off as liquid.

Jan 1, 1943

By Tibor Horvath

Dust abatement is possible on bulk materials, whether conveyed or stockpiled. Minimum (ppm) quantities of chemical additives can efficiently and rapidly control dust of conveyed substrates with no effect on floatation chemistry. Top coating of large surface areas can control surface dust and wind erosion. Environmental and toxicity impact must be considered in any treatment, especially on areas with percolation runoff, leachates, or limited containment. The most effective dust control is preventing release of substrate fines rather than trapping and removing air borne dust. Techniques to prevent release of fines from conveyed substrates will be discussed. Dust control dynamics are a very complex combination of solid phase physical and chemical interactions between the substrate and the fines. ?Smart Technology? products permit dust abatement of stockpiled substrates and tailing fields with no environmental impact. Using ?Smart Technology?, the dust abatement products remain active and can re-seal damaged areas. Efficient, low environmental and toxicity impact, dust control will be demonstrated through case studies where these principals have been applied.

Oct 1, 2010

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By R. J. Rotzinger

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By A. Anderko, V. G. Papangelakis, G. Moldoveanu, G. Azimi, M. Carlos

"OLI Analyzer is a software package that uses the powerful Mixed Solvent Electrolyte (MSE) model to simulate the behavior of multicomponent electrolyte solutions from infinite dilution to the limit of fused salt, and from temperatures below the freezing point up to near critical temperature of the mixture. The software also allows the creation of thermodynamic parameters for new chemical systems unavailable yet in public-domain or commercial software databanks. This communication reviews the basics of the model and provides some examples of modeling hydrometallurgical applications with emphasis on high temperature applications, including calcium sulfate scale formation in autoclaves, high temperature pH inference and iron control. INTRODUCTIONModeling of electrolyte systems has been of particular interest to various industrial processes, such as separation processes (e.g., solution crystallization, extractive distillation, seawater desalination or bio-separations), environmental applications (e.g., gas treatment, wastewater treatment or chemical waste disposal) and hydrometallurgy (e.g., pH control and neutralization, iron control, scaling and fouling of equipment). Using a chemical model, time-effective predictions of various properties of electrolytes can be obtained, which is beneficial not only during process monitoring, but also during process optimization and process scale up. As a result, pilot scale studies can sometimes be eliminated where budgetary constraints exist. Development of such a powerful model requires the use of a speciation-based model, in which solution chemistry is explicitly addressed (as compared with some models that treat electrolytes either as undissociated or fully dissociated systems), despite being computationally challenging. In addition, as a feature of electrolyte systems, speciation equilibria inherently influence the phase equilibria due to complex formation, ion pairing, and acid-base reactions. Therefore, how the electrolyte solutions behave at various conditions may differ significantly due to the non-ideality, which must be carefully addressed to obtain a model that is applicable to a wide range of conditions such as concentration, temperature, pressure and solvent system."

Jan 1, 2012

By R. P. Zahn

The need for quantitative mineralogical data to characterize ore types before they are processed is becoming increasingly necessary. Mineralogical data (modal abundances, grain size, liberation/locking characteristics, mineral textures and associations) can provide invaluable information to facilitate the identification of metallurgical issues that may arise during processing of a particular ore. This paper will discuss the use of QEMSCAN analysis in conjunction with bench scale flotation test work to determine metallurgical characteristics for several ore types that will be fed to the Morenci concentrator upon commencement.

Jan 1, 2007