Search Documents

By Narasimha Mangadoddy, Balraju Vadlakonda

"Bubble size distribution, bubble rise velocity and gas and solids hold-up are the key major hydrodynamic parameters that are extensively used for column flotation design and performance evaluation. The distribution characteristics of mean gas hold-up is studied using electrical resistance tomography (ERT) coupled with pressure transducers (PT) in column flotation. The ERT technique facilitates non-invasive and nonintrusive visualization of different flow regimes even in the presence of particles in a column flotation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas hold-up and its radial distribution has been analysed for both two-phase and three phase flows. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the three-phase flow hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, are employed to explore the influence of parameters in two phase flow in column flotation. Mean gas and solids hold-up values extracted from ERT have been critically analysed for the column operating in various flow regimes. Gas hold-ups and solid hold-ups results using ERT are in very good agreement with conventional estimation and correlations obtained using pressure transmitter methods. Meanwhile, the results show that the gas hold-ups in the centre region increase constantly with an increase in the superficial gas velocity, whereas solid hold-ups distribution is very heterogeneous for high gas velocity. Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the 'inside' flow behaviour of gas –liquid–solid three phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is perhaps the most significant technological innovation in flotation machinery and its successful introduction in mineral processing plants. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker & Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena, Biswal, Das, & Reddy, 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on performance of column flotation (Finch, J.A.;Dobby, 1991). Many techniques have been developed that could be used to experimentally analyse the hydrodynamics of column flotation. Tomography techniques are well sound to investigate the hydrodynamics for process equipment. Among that, Electrical resistance tomography (ERT) has been used in various industrial investigations for visualization of the concentration profiles and characteristics of the fluid dynamics in gas–liquid two-phase systems (Wang, Dickin, & Mann, 1999; Williams, R.A; Wang, 2000). ERT is an imaging technique to analyse the internal flow behavior non-intrusively. ERT provide very useful tools for measuring and monitoring of column flotation process on line. Due to its high speed capability, low cost measurement, robust sensors, ERT is considered to be the most powerful tool among other tomography techniques such as positron emission tomography (PET), magnetic resonance imaging (MRI), optical and infrared tomography. Application of ERT has extended in process systems due to its improved speed of data acquisition, sensitivity, flexibility and noise immunity. In multiphase flow of bubble columns, gas hold-up and solid hold-up are explored by using the coupling of ERT and difference pressure method (Jin, Han, Yang, & He, 2010)."

Jan 1, 2016

By W. S. Dyer

Considerable attention has been paid in recent years to the fire-clay and silica-sand deposits of the Mattagami and Missinaibi rivers and ? to the lignite occurring in them. The fireclay especially deserves this attention; it is of first-class quality; it appears to be widespread; it is the only fire-clay in central Canada, and part of it lies not more than 20 miles west of Coral rapids, to which point steel will be laid this coming spring by the Temiskaming and Northern Ontario railway. Undoubtedly, these clays will rapidly find a place in industry. The fire-clays and the better grades of silica-sand are Mesozoic in age and have been referred to the Lower Cretaceous or Upper Jurassic. Glacial clays and sands and Palaeozoic shales also occur in the same region, but are of little economic value, and will not be dealt with in this paper. Dr. Robert Bell was perhaps the first to discover the clays, since in the Report of Progress of the Geological Survey of Canada for 1877 and 1878 he reported beds of lignite on Coal brook, a tributary of the Missinaibi river, underlain by sticky clay and overlain by glacial drift. In 1880 E. B. Borron (1) discovered an extensive deposit of white sand and clay on the east bank of the Missinaibi river, five miles below Coal brook, and in 1890 (2) he examined the deposit found by Dr. Bell on Coal brook. He recognized that the underlying clays were quite distinct from the glacial clays of the region, and suggested that they might be used for fire-brick if metallurgical operations were undertaken in the region. Somewhat later, J. M: Bell described a deposit of fire-clay and silica-sand on the Wabiskagami river, another tributary of the Missinaibi.

Jan 1, 1928

The rate of liquid copper deoxidation during top blowing of reducing flames has been investigated using a high capacity thermogravimetric unit at 1200 °C. For 1 kg copper samples, it was observed that the rate of deoxidation was proportional to the flow rate of the reducing reagent (H2 or CO). Under similar experimental conditions, it was found that H2 is more effective than CO even though both have similar thermodynamic potential to deoxidize liquid copper. The rate of deoxidation of liquid copper with reducing 0 2/CH4 flames was measured for 0 2/CH4 molar ratios of 1.5 to 2. The deoxidation rate depends on the 0 2/CH4 ratio and decreases as it approaches the stoichiometric ratio (02/CH4 = 2). Estimation of the rate of deoxidation of liquid copper with top blowing flames based on the thermodynamic composition ofH2 and CO in the product gases, agrees well with measured values.

Jan 1, 2007

By Matej Petružálek, Tomáš Svitek, Tomáš Lokajícek

"Migmatite from the Skalka region (Czech Republic) was chosen as the experimental rock material. It has macroscopically visible plane parallel structure (foliation). The foliation was caused mainly by biotite grains arrangement. The cylindrical samples of migmatite with subhorizontal, subvertical and oblique foliation were uniaxially loaded up to the failure. Network of 8 broad band sensors was employed for acoustic emission monitoring and ultrasonic sounding. A grid search method with anisotropic velocity model was used for AE hypocenters localization. The source types of successfully localized events were determined from the average first arrival amplitude. Structural anisotropy of tested rock material caused the anisotropy of its mechanical properties (peak strength, Young’s modulus) as well as a different way of fracturing process in dependence on the angle between axial stress and foliation plane. The combination of splitting, shearing and sliding was found to control the fracturing of sample with subhorizontal foliation. The shearing and sliding was dominant in fracturing of samples with oblique foliation. With greater dip of foliation, the role of sliding increased at the expense of shearing. Due to the favorably oriented system of microcracks already present, the shearing and splitting was at the same level during fracturing of the sample with subvertical foliation before nucleation began.INTRODUCTIONThe process of failure of low porosity rocks depends on their mechanical properties and actual stress and temperature condition. At the low pressure and low temperature, the most common way is brittle failure, which is a progressive process requiring the initiation, growth and coalescence of cracks (Lockner, 1993). Stress strain behavior of low porosity crystalline rocks, during the laboratory compression experiments, is divided into four characteristic stages: crack closure, elastic region, stable crack growth and unstable crack growth which leads to the brittle failure, Brace et al. (1966) , Bieniawski (1967), Lajtai (1974), Cai et al. (2004), Nicksiar and Martin, 2012 and 2013.The fracturing process of stressed rock begins with the crack initiation (sci), which for low porosity rocks occurs approximately at 40-50% of peak strength (sp) (Cai et al., 2004; Nicksiar and Martin, 2013). After the sci, the dilatancy begins and stable crack growth follows up to the crack damage threshold (scd), which is approximately at 80% of sp (Cai et al., 2004). After crossing the crack damage level, there is an unstable crack growth accompanied with nucleation of fault plane (sn) at 97-100% of sp. (Rao et al., 2011). The stress drop accompanied with formation of macro scale shear failure plane follows after peak stress is crossed."

Jan 1, 2015

By Du Xinfeng

The resource quantity of the low rank coalbed methane (CBM) accounts for 47% of the total resource quantity of CBM in China. Compared with the exploration and development of the high rank CBM in Qinshui Basin, China and the low rank CBM in Powder River Basin, USA and Albert Basin, Canada, the exploration and development of the low rank CBM are still in the initial test stage. In this paper, on the basis of analyzing the mining geological conditions such as that the Huanglong Jurassic Coalfield is largely situated in the hills and gullies zones, and the coal reservoir has the features such as the low metamorphic degree, large coal seam thickness, simple coal matrix texture, high permeability and small CBM content and so on, it discusses the key technologies such as the development pattern of CBM, well location arrangement, drilling and well completion technology and fracturing technology and so on. It indicates that the underbalanced drilling and the cavity well completion based on the reservoir protection will be the development directions of the CBM development technology in this area.

Aug 1, 2013

By F. Vagnon, A. M. Ferrero, M. Pirulli, A. Segalini

"The topic of this study is the design of flexible fences to mitigate the risk due to debris flow phenomena by means of theoretical and experimental studies analysed in framework of the Rock Engineering System (RES).The study of the interaction between debris flows and flexible barriers is a major challenge since many different aspects concerning both the slope characteristics and the structure features are involved. Debris flows are often triggered by the mobilization of debris deposits that are generated by rock fall of adjacent rock walls. The rock debris deposits are difficult to be characterized by the physical and mechanical point of view due to their large variability in volume distribution and, moreover, when dealing with high mountains environment, they are also strongly affected by the presence of water at different phases (solid or liquid) depending on the temperature. The debris deposit turns unstable in relation with the geotechnical and environmental features of the areas and the instability evolution in high mountain steep valley is often a debris flow. Debris flow destructive potential is very high and protections are often needed to reduce the debris flow risk.This complexity determines the needs of comprehensive study able to include the global basin dynamic and the environmental conditions. An a-priori analysis of the influence of the different aspects can be useful to focus on the real driving aspects of the problem. Due to the complexity of the system the application of the RES methodology is recommended in order to clearly define the different assumptions needed, their influence on the simulations and a comparison among them.RES allows investigating triggering criteria, flow and depositional processes and interaction of flows with protection fences in a rational way. For this purpose, an interaction matrix is created: it summarizes the key geotechnical parameters that influence debris flows, their interactions and debris/engineering protection opera behaviour. The goal is to quantify the diagonal-off terms to assess the residual risk after barrier construction, using back analysis from real debris flow event and data collection from literature.This methodology is applied to analyze a debris flow event in the Italian Western Alps where numerical analyses are carried on to assess flow characteristics to be used for fence design through the application of an analytical and numerical model developed by the authors (Brighenti et al, 2013). In particular, the velocity and deposition heights have been estimated using the numerical code RASH3D (Pirulli, 2010), which is a single-phase model based on depth-averaged Saint Venant equations. Pathways of different lengths are studied to assess the input data necessary to design the protection barrier and to determine the associated risk. Simulation of the barrier at different places along the valley will also allow to determine optimal barrier location in terms of minimum residual risks by comparing the velocity, the volume and the energy of the debris after the barrier impact.The work will produce a possible design scheme to be adopted in this environment."

Jan 1, 2015

By M. Kermani

This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of cemented mine backfill which are deslimed tailings, water and binders. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. Initially, the influence of sodium silicate concentration on the mechanical properties of samples was evaluated using the unconfined compressive strength (UCS) test. Consequently, the effect of curing temperature on CHF and Gelfill samples cured in various curing temperatures ranging from 5?50 °C was studied using the UCS test. Microstructure of selected samples was studied wirth the mercury intrusion porosimetry (MIP) technique. This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Curing temperature strongly influences the mechanical and microstructural properties of CHF and Gelfill samples. (iv) The microstructure analysis revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill which can contribute to the better mechanical properties of Gelfill. (v) The MIP tests suggested the microstructure of specimens were changed by adding sodium silicate in a way that the Gelfill samples had a higher percentage of fine pores than CHF samples.

Aug 1, 2013

By S. M. C. Santos

Preliminary bench-scale studies were carried out on the leaching of a zinc sulphide concentrate from Somincor, Portugal, and the purification of the resulting pregnant solution using solvent extraction techniques. The sulphide concentrate contained 36% Zn, 36% S, 2% Fe and 4% Cu. The leaching was carried out with sulphuric acid in the presence of ferric sulphate as the oxidant. Important leaching parameters, such as the effect of reaction time, the solid-liquid ratio, temperature and concentrations of acid and oxidant, were investigated. After leaching, the recovered solution was contacted with an organic phase containing Acorga 5640 to remove the copper. Subsequently, the removal of iron from the leaching solution was achieved with a mixture of Cyanex 272 and TBP. This solvent mixture was relatively selective for iron over zinc. The stripping of the loaded solvent was performed with 200 g/L H2SO4. Six countercurrent extraction stages achieved a separation of about 99% of the iron from the leaching solution. The iron-free leachate can be further treated to recover minor metals by cementation, and finally, zinc by liquid-liquid extraction. The advantages of the suggested process relative to the traditional jarosite process are discussed.

Jan 1, 2006

By R. Flood

"Oil has been discovered off Newfoundland in a number of locations on the Grand Banks, the most notable and exciting being in 1979 when Hibernia was discovered. This discovery has brought new challenges to the province as well as to all of Canada. During the seven years"" since its discovery, both industry and governments have attempted to define its parameters and to find the most efficient and economical way to develop the field.A number of studies have been completed during the interval and in 1985, Mobil Canada Ltd. and partners stated that they would prefer to develop the field by using a concrete Gravity-Based Structure (GBS). IntroductionHibernia is located in an environmental climate much more severe than that of any previously developed oil field. The wind and wave conditions are similar to those of the North Sea, but unlike the North Sea, any structure on the Grand Banks would have to contend with ice floes and icebergs. Decisions had to be made on whether fixed structures could be put in place that would withstand the pressures of the ice and the impact of an iceberg, or whether structures that could be removed when such impacts were imminent would be used.Early studies in 1981, determined that it was possible to build a concrete Gravity-Based Structure which could withstand the impact of the largest icebergs that are anticipated to float in that area of the banks.Additional studies increased the knowledge of icebergs: their patterns and size, and verified the original conclusions that Concrete Gravity-Based platforms would provide a practical solution."

Jan 1, 1988

By S. Orangi

A representative sample of ramming paste from a peripheral seam in an aluminium electrolysis cell was taken in order to develop a process to fabricate ramming paste samples in the laboratory. To this end, paste material was compacted in multilayers in a mould designed to be representative of peripheral seams in Alcoa's smelters. The density distribution in the representative sample was measured ranging from 1.51-1.76 g/cm3. The density range obtained by the proposed methodology in laboratory is 1.47-1.77 g/cm3. The results demonstrate that the proposed fabrication method adequately duplicates paste density from the cell for both one and two layer compaction. Finally, preliminary results related to the compressive strength and Young's modulus of laboratory samples were obtained at various temperatures and are presented in this paper.

Jan 1, 2011

By T. W. Bingay

The production of both lead and zinc in Canada has steadily increased during recent years until today Canada ranks among the world's leading producers of both of these metals. The high prices which they have commanded have led to an energetic search for new deposits and also to an investigation of abandoned properties which, under the present conditions of better prices and more efficient methods of treatment, offer chances of commercial success. It is confidently expected that during the next few years success in both these lines of activity will further increase Canada's lead and zinc output, giving her a still higher ranking among the world's producers. In 1926, approximately 140,000 tons of metallic lead was produced from ores mined in Canada, and of this, 125,000 tons was refined in Canada at Tadanac, B.C. During the same year the production of metallic zinc from Canadian ores amounted to 68,000 tons, of which 62,000 tons was refined at Tadanac. History Of Lead and Zinc in Canada The production of lead in Canada is much older than that of zinc. The chief source has always been the interior of British Columbia. As earl y as the 'eighteen twenties', Indians and Hudson's Bay Company's trappers had discovered an outcrop of lead ore on the site of the present Blue Bell mine on the east shore of Kootenay lake, but it was not until1865 that active prospecting for lode deposits began. In the early nineties the activity of the silver-lead-zinc region of the Slocan reached its culmination and a steady production has been maintained down to the present time. Up to the end of 1924 the Slocan area produced over 38 million ounces of silver, nearly 300 million pounds of lead, and almost 122 million pounds of zinc.

Jan 1, 1927

By M. Jorgensen, I. Markland, D. Shuck

"The McLaughlin Mine owned by Homestake Mining Company is located 70 miles northeast of San Francisco in California's coastal range. The mine began operations in February of 1985. The mill currently processes 3,000 short-ton per day of sulfide ore that has an average grade of 0.15 ounces of gold per ton, plus another 3,000 tons per day in a newly completed oxide circuit. Annual production from the mine totals over 200,000 ounces.The sulfide ore extraction process involves three basic steps, grinding, oxidation of sulfide minerals in an autoclave, and cyanide leaching for recovery of gold in a carbon-in-pulp circuit. This process, which incorporates a new technology where oxidation of sulfide minerals is conducted prior to cyanide leaching to facilitate gold recovery, was successful from start-up. However, limitation in the grinding mills initially limited sulfide tonnage throughput.This paper discusses modifications made in the grinding circuit, both mechanical and operational, to resolve it deficiency. The SAG mill, in particular, was unable to achieve design tonnage initially and proved to be most troublesome. Complications occurred due to the hardness and variability of ore being processed, short component life, and a lifter /liner arrangement that had to be tailored to the particular circumstances at McLaughlin. IntroductionHomestake Mining Company's McLaughlin Mill, located in northern California, was designed to process a refractory gold ore at a rate of 3,000 tpd to render the ore amenable to cyanidation. Seven years transpired between discovery of the near-surface ore body in 1978 and the February, 1985 plant start-up. Development of the McLaughlin mill and open pit gold mine hinged on the use of autoclave technology to achieve design recoveries."

Jan 1, 1991

By Robert B. Parsons

"It is easy to throw darts at government - and government often deserves to be a target. This month, Tax Notes examines tax legislation from a different angle, and sees some bright spots.The following article is based on a paper presented by the author at the International Gold Symposium in Rio de Janeiro in August 1989Introduction""No man's life, liberty, or property are safe while the Legislature is in session.”With one federal government, ten provincial governments, and two territorial governments all claiming to have constitutional rights to tax and otherwise regulate Canada's mining industry, and with each of these thirteen governments pursuing their respective rights with some vigor, government involvement in one way or another is an accepted way of life in the industry. While one's initial reaction to government involvement in an industry might be one of scepticism or fear, generally speaking the federal, provincial, and territorial governments in Canada tend to be pro-mining. They recognize the importance of the mining industry to Canada, especially in terms of job creation and exports. It is not surprising, then, to find that an array of valuable fiscal incentives are available to the industry through federal and provincial legislation.This paper summarizes the principal incentives that are inherent in Canada's tax legislation, as well as the Canadian Exploration Incentive Program. Although it is beyond the scope of this paper to deal with all of the incentives that are available, it is noted that various forms of federal or provincial assistance are also available outside of specific legislation, through negotiation with government departments. This latter type of assistance is generally directed toward helping with the cost of infrastructure such as roads or hydro lines, or Jess often toward loan guarantees or similar financing assistance."

Jan 1, 1990

By Anthony McDonald, Dominic Verhelst

"Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) started up a zinc plant and smelter in late 1930, employing technology of that period. The zinc plant has since converted from a roast/leach operation to a two stage pressure leach operation to eliminate sulphur dioxide emissioms. The smelter, however, is still continuing with much of the original roaster/reverberatory furnace technology. This paper reviews the process flow of the copper smelter, with some comments on past and recent changes.Smelter FlowsheetPrior to July 1993, the HBM&S smelter operation consisted of seven areas, namely feed preparation, roasters, reverberatory furnace, converters, anode casting, fuming plant, and dust collection. A simplified smelter flowsheet is shown in Figure 1. The data for tonnage of materials moving through the circuit are presented in Tables I to 4, and are representative of the time period from July 1992 to June 1993. A change in the zinc plant technology in 1993 resulted in the elimination of a zinc-bearing sulphide leach residue from the smelter feed blend, thereby greatly reducing the zinc content of slag produced in the smelter. Consequently the fuming plant and ancillary equipment, such as the drying plant, were shut down. These areas will, however, be described. With the closure of the zinc fuming furnaces all the slag from the reverberatory furnace is now discarded to stockpile.The over-all smelter metal recoveries are 96% for Cu and rn.5010 for Au and Ag. Figures 2 and 4 indicate historical production numbers of copper, silver and gold, respectively. A review of the minor element distribution in the smelter can be found elsewhere."

Jan 1, 1994

By S. K. Paul

"This paper briefly describes the underground crushing and conveying system at Sherritt Gordon Mines' Ruttan Mine. A series of three steel-cord belted conveyors, with a total length of 2J55 metres and a total vertical lift of 407 metres, convey the muck from the underground crushing station to the mill at the surface. The maximum size of the crushed rock is 6 in. All the conveyors are provided with numerous safety and fire suppression devices. IntroductionThe Ruttan Mine of Sherritt Gordon Mines Limited is located 20 km east of the town of Leaf Rapids, 760 km north of Winnipeg. The orebody is multilensed, with lens width varying from 6 to 45 m. Ore production started in 1973 with the opening of a 10,000-tpd open-pit mine. Initial development of the underground mine was started in 1972 with the driving of parallel conveyor and access declines at minus-2507o gradient to the I 220-m level, and then the access ramp was further extended to the 1160-m level. Exploration drifting was done on the 1280-m and 1160-m levels from the access ramp. The final development plan for the underground project was approved in January 1977, and full-scale development and constructionwere resumed.At present, Ruttan Mine is in a period of transition from open-pit to underground mining. Ore production is now coming from both operations. By mid-1980, open-pit production will cease and all production will come from the undergroundmine.The underground mining method at the Ruttan Mine is sublevel open stoping with delayed backfilling. The orebody is divided along strike into a series of 27-m-long stopes and 15-m pillars, both 60 m high."

Jan 1, 1980

By Peter A. Bevan

"In massive and semi-massive deposits, it is essential to take samples continuously for specific gravity determination as well as for assays of the various metals of interest. Failure to use specific gravity in mixed deposits of high density contrast will result in incorrect determinations of the average grade.Graphs and linear equations of specific gravity against the grade of one metal are not considered accurate enough in a multi-mineral deposit, but appear to be very satisfactory in a theoretical one-sulphide/gangue mix. Specific gravities based on base-metal values only in massive sulphide deposits will result in underestimating the effect of low grade areas on the average grade and also cause a reduction in the calculated tonnage.IntroductionBy definition, a base-metal assay is the percentage of metal by weight contained in a sample, whether it be a soil or silt sample, a grab, chip or channel sample, or a section of diamond drill core.In those cases where there is a series of contiguous samples, say in diamond-drill core, the average grade may be required of the various assays that are above a desired or required cutoff grade.Internal low grade or waste can be included if the assays one side or the other are used to ""carry"" the lower grade material and the resulting average grade is above the cut-off grade. To determine the average grade, the individual assays are ""weighted"" by multiplying these values by their respective lengths, adding up the cumulative assay times length and dividing by the total length. This method is essentially a weighting by volume, because the core diameter is constant and is common to all the samples being considered for estimating the average grade . If some of the core samples have much higher specific gravities than others, and the specific gravities are not used in the weighting process, the resultant average grade will be over-estimated or underestimated, depending on the grade of the heavier sections. When core assays of approximately the same specific gravity or weight are averaged by length, the error in the weighted estimation of the average grade is negligible."

Jan 1, 1993

"Nanisivik Mines Ltd. operates a 10-M W diesel-electric generating plant at its zinc-lead operation on Baffin Island in the Canadian Arctic. This paper provides a description of the plant and the integrated waste heat recovery system. Data is presented detailing the actual costs of operating a plant over a period of seven years. Problems in operation are described as well as the success of the plant in meeting its objectives over the years. IntroductionNanisivik is located on the shore of Strathcona Sound at the north end of Baffin Island (Fig. I). Nanisivik Mines Ltd. has operated a 2,100 tonne per day zinc-lead underground mine and a concentrator, together with supporting infrastructure, at this location since October 1976. Annual production of 100 000 tonnes of zinc and 10 000 tonnes of lead concentrate is transported by ship to Europe during the mid -July to mid October shipping season.All electrical needs of the project are provided by the company-owned and -operated power plant. Facilities served by this electrical system are the underground mining areas, the concentrator and industrial area, a townsite, airport, and shiploading dock complex."

Jan 1, 1986

By Graham E. Brown

Since the beginning of time, people later to be known as engineers and architects have strained to create methods whereby they could improve technology to assist them in their various fields of endeavour. Some of these improvements would be the change from linen paper, french chalk and ink pens to drafting film , mylar an d pencil for the production of drawings, the drafting machine in lieu of the tee and set squares, even tap e to attach drafting media to the board instead of thumb tacks and man y, man y more. All of these taken individually are insignificant but combined evolve to the current state-of-the-art in the computerized engineering environment. Ten years ago the major topic o f conversation was the hand-held calculator which for a cost of around $150 would give most trigonometric functions. Today the equivalent calculator can be purchased for around $25, is about one third the size, and if inflation were included over the last ten year s the item should cost around $550 in today' s dollars, it can be seen that tremendous advances not only in the technology but also the cost saving. The following paper is intended to outline some o f the significant aspects o f the latest technology in the computerized engineering office namely Interactive Graphics Systems.

Jan 1, 1985

By Kazutoshi Haga, Batnasan Altansukh, Yasushi Takasaki, Mohd Yazid Bin Abdul Razak, Atsushi Shibayama

"In this study, the volatilization behaviour of arsenic (As) and antimony (Sb) from arsenicantimony bearing minerals such as tennantite (Cu12As4S13)/tetrahedrite (Cu12Sb4S13) in copper ore was investigated using a roasting process. Specifically, the thermal decomposition of tennantite and the arsenic volatilization were investigated under nitrogen and air atmosphere. The roasting experiments were performed at temperatures ranging from 500 to 1,200oC and different retention times using a laboratory electric furnace. The results indicated that over 95% volatilization was achieved at 700oC. On the other hand, when the temperature increased to 1,200oC, volatilization rate of Sb reached to 90%. Therefore, volatilization of Sb requires high temperature compared to As. It suggests that As and Sb can be separated using temperature difference. Selective removal of As is possible at 700oC, subsequently Sb can be recovered as a volatilized product by increasing the temperature to 1,200oC. Meanwhile, volatilization of Cu and Fe was not observed on these conditions. The content of As and Sb in the residues obtained from roasting at 700 and 1,200oC was less than 0.3 and 0.75 mass%, respectively. The Cu content in solid residue at 1,200oC increased to 34 mass%. The clean copper concentrate with lower amounts of arsenic and antimony was obtained from the process. INTRODUCTIONRecently, arsenic (As) and antimony (Sb) contents in copper (Cu) concentrates are increasing year by year. Arsenic and antimony are present with Cu minerals such as enargite (Cu3AsS4), tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that associate with copper sulfides [chalcopyrite (CuFeS2) and bornite (Cu5FeS4)]. They are normally concentrated by flotation and treated in copper smelters. However, treatment of copper concentrates containing high amounts of arsenic and antimony by a smelting process is difficult due to environmental implications of toxic arsenic and antimony. As demand for copper continues to grow, the need to source copper from several types of resources including those that contain high levels of As/Sb becomes necessary. Therefore, a novel processes for the treatment of As/Sb bearing Cu concentrates are required. Reviews on copper resources such as enargite, tennantite and tetrahedrite containing high amounts of arsenic and antimony are covered widely in literatures by many researchers (Padilla et al., 1998; Welham, 2001; Vinals et al., 2003; Guo & Yen, 2005; Balaž & Achimovicova, 2006a; Filippou et al., 2007; Mihajlovic et al., 2007; Lattanzi et al., 2008)."

Jan 1, 2016

By Chuan-Jian Zhong

Gold-based nanoparticles in the size range of a few nm have attracted increasing interests in catalysis, sensors and biomedical applications. The study of the unique catalytic properties of nanosized gold was inspired by the pioneering work of Haruta on the nanogold-catalyzed CO oxidation (1-4). There have been a number of excellent reports discussing both fundamental and application aspects of gold nanoparticles in catalysis (3-8). Our work reported herein is aimed at investigating the preparation and application of gold and its alloy nanoparticles for potential applications in fuel cell catalysis. Fuel cells operating by electrochemical oxidation of hydrogen or methanol fuels at the anode and reduction of oxygen at the cathode are attractive power sources due to their high conversion efficiencies, low pollution, lightweight and high power density. While methanol offers the advantage of easy storage and transportation in comparison with hydrogen fuel cell, its energy density (~2000 Wh/kg) and operating cell voltage (0.4 V) are much lower than the theoretical energy density (~6000 Wh/kg) and the thermodynamic potential (~1.2 V). The poor activity of the anode catalysts and inefficient activity or issue related to "methanol cross-over" at the cathode electrode are associated with the loss of about one-third of the available energy at the cathode and the other one-third at the anode. Extensive studies have been focused on Pt-group metals (Pt+Pd+Rh+Ru+Ir (PGM)) for both anode and cathode catalysts. A major problem is the poisoning of Pt by COlike intermediate species (9,10). Recently, oxide-supported gold nanoparticles in the <10 nm size range have emerged as one of the best catalysts for CO oxidation (1-3,11), and for water gas shift reaction in reforming stage using 5 nm Au on Fe2O3 (6). Gold and its alloy with other metals in the nanosize range present new alternatives (2,12). Whether the unique properties of gold nanoparticles can be exploited for addressing these problems is a focus area of our work. The ability to harness the large surface area-to-volume ratios and the unique surface sites of nanoparticles in <10 nm size range, especially in heterogeneous catalysis, constitutes a major driving force in fundamental research and practical applications of nanoparticle catalysts. It is this size range over which the metal particles undergo a transition from atomic to metallic properties. The understanding of factors controlling the morphological and surface reconstitution associated with such a size range is of fundamental importance to the ultimate exploration of nanostructured catalysts. We have been investigating the interfacial structures and properties of core-shell types of nanoparticles consisting of gold or alloy nanocrystal cores and organic monolayer shells that were prepared by twophase synthesis (13) and processing (14) protocols. Important attributes of such nanoparticles include controllable size monodispersity, processibility, and stability towards size- and composition-tunable catalysis (15-21). Some of these attributes were studied for understanding their electrocatalytic properties in the oxidation of methanol and reduction of oxygen, which are of fundamental interest to fuel cell technology.

Oct 1, 2003