Search Documents

By Timothy W. Ellis

Wire Bonding is the dominant IC interconnection process presently used in the semiconductor assembly industry (1). The flexibility, adaptability and cost of wire bonding will continue to keep it as the key process for the interconnection of integrated circuits to substrates. However, wire bonding still has certain technological hurdles to overcome if it is to continue following the semiconductor roadmap (2). Particular issues which need to be addressed include low overall tensile strength, low elastic modulus, low shear per unit area and mechanical loop stability of Gold based micro-alloys. The ability to produce ?Deformation Process Metal-Metal Matrix Composites? (DMMCs) is based upon the deformation nature of immissible metallic systems. For reference, the Gold (Au)-Molybdenum (Mo) phase diagram is shown in Figure 1 (3). By inspection of the diagram, Au has a very low solubility for Mo, while Mo has essentially no solubility for Au. This is the metallurgical analog of oil and water. In the Au-Mo case, this is particularly troublesome when producing precursor ingots of the alloy to be formed into wire products. In Table 1, the melting points and densities are shown for Au and Mo. As shown, the melting point of Mo is significantly higher than Au, and is very close to the boiling point of Au (2856°C). However, Au?s density is higher than that of Mo. As such, conventional casting techniques are not suitable, since solid Mo would float off the surface of an Au melt thus depleting the matrix of its alloy addition. In this work, two-phase composite wires were produced by deformation processing to develop an interconnection wire with elevated tensile strength, modulus and shear to those commonly available in the market (4). This technology has been used previously in the production of high strength electrical conductors particularly for high field pulsed magnets (5).

Oct 1, 2003

By Jochen Petersen, Diane Taggart

"At an average of 90.3% (for the period of 1 January 2009 to 30 September 2011), Zincor’s zinc recovery was well below the industry standard of 96%. The losses through the residues, in particular the iron residue, were the biggest contributors to the overall zinc loss. It was believed that this loss could be decreased with the implementation of seed recycling. A plant trial was run to test the implementation of a seed recycle. The rate of seed addition through recycle was increased over a 4-week period. The presence of seed decreased the insoluble zinc loss by providing additional surface area for iron to precipitate onto, and reducing coating of unleached neutralising agent. The soluble zinc loss was also decreased at low and moderate seed recycle volumes. The improvement was attributed to agglomeration growth of the recycled particles, which improves the dewatering characteristics of the precipitate. In contrast, the soluble zinc loss increased at high seed recycle rates. This result was attributed to particle crowding and a low wash ratio.INTRODUCTION The Zincor refinery, which closed in December 2011, was situated just outside of Springs in the Gauteng Province of South Africa and employed the conventional Roast-Leach-Electrowin process, which accounts for 75 to 80% of the annual primary zinc production in the world. The refinery fed up to 220 000 t/a of zinc sulphide concentrate. The major portion of the raw material was sourced in Southern Africa from the Rosh Pinah and Black Mountain mines. Between 20 000 and 40 000 t/a of material was imported to make up the deficit and to improve the grade of the feed material. The iron contained in the zinc concentrates, at an average of 6.03% (for the period of 1 January 2009 to 30 September 2011), resulted in the formation of zinc ferrite during roasting, which is insoluble under atmospheric leach conditions. At Zincor, most of the zinc ferrite was dissolved in the residue treatment plant at elevated temperature and high acid strength. The leach liquor from this aggressive leach contained between 15 to 30 g/L of iron, mostly in the ferric form, and was known as the hot iron solution (HIS). The presence of iron in the liquor had an adverse effect on the zinc operation, particularly on the current efficiency in the electrowinning circuit. Therefore the iron needed complete removal."

Jan 1, 2016

By R. Luchese de Moraes, J. A. Matthews, C. Feliciano Bruzual

The role of biomass char in blast furnaces has been re-examined by scientists worldwide, as a feasible option to reduce the carbon intensity of ironmaking. This contribution makes a technical and economic analysis of the ferro gusa industry in Brazil, with the last 172 charcoal-Blast Furnaces operating in the world. A key strategic question is presented: what is the current status and future prospects of biomass use in Blast Furnaces? Findings provide significant implications to metallurgists: while ferro gusa from charcoal is regarded as carbon neutral iron with low impurities, there are limiting factors that hinder the further proliferation of charcoal-BFs: biomass generation requires vast extensions of arable land and aggregates have low production capacity. Additionally, most of the charcoal is presently generated in beehive kilns with low yields. These elements combined make charcoal-hot metal expensive in price. With respect to the future prospects of biomass, the injection of small biochar particles through the PCI rigs in BFs (here coined Bio-PCI) and iron ore sintering may offer a practical alternative to significantly reduce the CO2 emissions in the ironmaking process.

Jan 1, 2015

By T. Holmes, J. Middlemiss

"Agnico-Eagle (AE) has been operating their Kittila Mine in Northern Finland since 2008. The mine has experienced considerable ore flow problems with ratholing, bridging and freezing in their mill feed bin since start up. In the first winter of operation, the entire central portion of the contents of the cylindrical flat-bottomed 2000 tonne mill feed bin froze. Flow was erratic and could only be achieved through small diameter ratholes. To maintain a reasonable, albeit limited, feed to the mill, the bin had to be kept less than ½ full and a portable steam generator was brought in to melt the frozen agglomerates that frequently blocked the outlets. The combination of limited surge capacity and frequent outages required the crushing plant to operate 24/7 and resulted in inconsistent production levels and high operating costs.AE had planned to expand the processing plant to increase throughput by about 30% when they transitioned from open pit to underground ore. These plans presented an opportunity to improve the material handling.To avoid the problems experienced with the original mill feed bin, AE enlisted Jenike & Johanson Ltd. (J&J) to test samples of the ore, and based on the measured flow properties to provide design recommendations to ensure that the new mill feed bin would operate reliably. The new 2000 tonne expanded flow mill feed bin and apron feeder were installed in 2014 and are now supplying almost 93% of the total mill feed with the remaining coming from the original bin.IntroductionIn early 2009, AE engaged J&J to visit their then recently opened Kittila mine and mill in Northern Finland (Figure 1). Over the first half-year of operation, production had been restricted in the ore handling and storage system by flow problems such as ratholing, bridging and freezing including blockages of chutes and hoppers as a result of frozen fines buildup and large frozen agglomerates. AE wanted to increase production in the existing open pit mine and mill feed operation and also wanted to avoid similar ore handling problems when they commissioned the new underground mining system under development at that time."

Jan 1, 2017

By Catherine T. Ziten

Introduction ?Environmental assessments required for permitting ?Focus on ammonia produced through mine construction & blasting ?Water quality guidelines: federal, provincial, IGO ?Reported values are typically estimates from other projects ?Predictive modelling of ammonia aimed to assist planning

May 1, 2009

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

By K. Pirapakaran

The Geotechnical Engineering research group at James Cook University has been working closely with all the leading mines in Australia in the area of minefills. They have carried out substantial research and consulting work on the drainage and stress developments within hydraulic fills. The objective of this paper is to summarize their work during the past five years on hydraulic fills. The paper will serve as a one-stop reference, pointing to relevant literature including the authors? own publications, on various issues covering drainage and stress developments within hydraulic fills. More than 15 different hydraulic fills, representing five major mines in Australia, were studied. Their grain size distributions and placement characteristics including permeability, porosity and dry density were studied and comparisons were made with the limited in situ data available in the literature. Stress development within hydraulic fills has been studied to minimize the risk associated with barricades failure. FLAC and FLAC3D were used to model stress developments within the hydraulic fills and were compared against the approximate closed form solutions available in the literature. A laboratory model was developed to study arching effects within the hydraulic fills.

May 1, 2007

By Gordon Sproule

THE papers presented to the Institute, and published in the BULLETIN, in the past three years, may be classified as follows: Geology, Mining, and Milling 89 or 58.5 per cent Smelting, Refining, and Refractories 17 " 11.2 " Mechanical and Physical Metallurgy 7 " 4.6 " General (Economics, Welfare, etc.) 39 " 25.7 " Total 152 100 These figure~ should be excuse enou.gh for. the present paper. As indicated by the title it is proposed: I.-To review briefly some of the more recent developments of Physical Metallurgy; and 11.-To show how Physical Metallurgy functions as the link between mining and production metallurgy on the one hand, and consumption engineering on the other hand. Io these days of specialization, papers of the kind being considered mostly gravitate to the American Society for Metals, the American Society for Testing Materials, the Institute of Metals, and the Iron and Steel Institute. In proof that there is a place for the newest and most specialized of these societies, the American Society for Metals, it may be said that in the Montreal Chapter there are 200 active members, and in the Ontario Chapter more than 200. Yet the overshadowing glamour of the mining industry proper, and the publicity it receives, result in an almost continuous dearth of students in metallurgical engineering at our universities. There are more jobs than graduates.

Jan 1, 1936

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961

By George Hope, Brigitte Lacouture

"The Red Dog Mine has increased mill throughput for most years since startup. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Late in 1999, a new circuit was designed with increased flotation capacity while simplifylng the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, twentyone (21) Outokumpu OK50 mechanical flotation cells and four (4) 3.66m dia. column cells will be added to the current flotation circuit. The VIP (Value Improvement Program) Mill Optimization project is also addressing thickening, water treatment and power issues and has a total budget of $US105 M. Startup of equipment will be phased in to minimize the impact on current operations and is expected to be complete by the end of Q3-2001.INTRODUCTIONRed Dog Operations started production in November 1989. The mine is located above the arctic circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred (100) days of open seas. Typical of sedimentary exhalative deposits, the metallurgy proved to be challenging and coupled with many mechanical shortcomings, the initial few years were very difficult. The start-up issues were slowly resolved and in 1998, a major grinding expansion, the PRI (Production Rate Increase) project, was completed. The project was designed to allow a 40% increase over the 1995 throughput. In 2000 mill throughput was 3,050,000 tonnes to produce a total of 960,000 and 140,000 dry tonnes of zinc and lead concentrates respectively, making Red Dog the largest zinc concentrate producer in the world. To address a shortage of flotation capacity remaining from the PRI grinding expansion, a project designated as the VIP (Value Improvement Program) Mill Optimization project was initiated. The mill optimization project is targeted to produce 1,100,000 tonnes of zinc concentrate at 56% zinc grade and 87% zinc recovery. The project will add twenty-one (21) Outokumpu OK50 (50m3) flotation cells, four (4) 3.66mO column cells and address water treatment, thickening and power generation capacities."

Jan 1, 2002

By D. A. Rhys, M. Sieb, M. A. Prefontaine, C. L. Swanson, S. R. Frostad, H. Q. Smit

"Gold-silver mineralization at Red Mountain (1992 resource of 2.5 million tonnes grading 12.8 g/t Au and 38.1 g/t Ag) occurs within several discrete zones within a folded sequence of Middle to Late Triassic Triassic sedimentary rocks, Early Jurassic volcaniclastic and pyroclastic rocks, and Early Jurassic intrusions. Three phases of Early Jurassic sills and stocks collectively comprise the Golds/ide intrusions: (1) irregular bodies of medium-grained hornblende monzodiorite (Hillside porphyry); (2) hornblende-biotite + quartz porphyritic monzodiorite to quartz monzodiorite (Golds/ide porphyry; U-Pb zircon ages of 197.1 + 1.9 Ma); and (3) biotite porphyritic hornblende monzodiorite sills (Biotite porphyry). Contact breccias and igneous breccia dikes are common features of the Golds/ide intrusions. Chemical similarities and equivalent ages of volcanic rocks and intrusions, and the presence of intrusive clasts in volcanic rocks suggest that the intrusions are feeders to overlying volcanic units.Hydrothermal alteration affects all pre-Tertiary rocks on Red Mountain, including all phases of the Golds/ide intrusions. Several shallow-dipping alteration zones are developed sequentially above a propylitic quartz stockwork/molybdenum zone. These include: (1) sericite-quartz-pyrite alteration (pyrite-dominant alteration); (2) chlorite-K-feldspar-sericite-titanite alteration with disseminated and vein pyrrhotite (pyrrhotite-dominant alteration); and (3) brown to black tourmaline veins and K-feldspar-pyrite-titanite-actinolite alteration. Anomalous gold(> 0.3 g/t) mineralization is developed at the transition from the pyrite to the pyrrhotite dominant alteration over a > 1 km2 area. Within this anomalous zone, high-grade (3 g/t to 20 g/t Au) gold-silver mineralization occurs in 5 m to 29 m thick, semi-tabular pyrite + pyrrhotite stockworks with intense sericitic alteration and surrounding disseminated sphalerite + pyrrhotite.Stratigraphic, spatial and geochronologic relations and alteration zoning indicate that mineralization formed in a subvolcanic environment at the top of the Golds/ide intrusions and at the base of the Early Jurassic volcanic pile. The Golds/ide porphyry is interpreted to be the mineralizing intrusion. The alteration zoning, molybdenum-copper mineralized quartz stockworks, extensive Ksilicate and tourmaline alteration, and the relationship with a hypabyssal porphyritic intrusion show similarities to many porphyry systems."

Jan 1, 1995

By Yun-Jie Wei

Seismic areas were in the eastern margin of the Qinghai-Tibet plain, whose structures were complicated, mainly composed of Maowen fault, Yingxiu fault and Pengxian-guanxian fault. The rapid rise of the Qinghai-Tibet plain led the crustal material of the eastern edge to move to the southeast along the faults on a large scale since the late Cenozoic; Minshan block structure and Long Men Mountain tectonic zone represented the strong nappe thrust movement as the east boundary of Chuanqing slip block; the stress was accumulating when squeezed, which to a certain extent resulted in breakdown of the crust, and earthquakes. The shock speed, high-energy accumulation, and the reversed dextrorotation of the earthquake fault characteristics et al. happened, which caused the development of secondary geological disastersts. According to on-site investigation, the typical geological disasters had thrust rock collapse, the instability deposit, the revival of potential debris flow et al. whose genetic model had been analysed.

May 1, 2009

By J. G. George

A brief review of the silver industry is presented to set the stage for the analysis of the distribution of silver production by source from various types of mines in Canada and of the changing relationship between the total output of silver and the total output of base metals. The decline in the average grade of the Canadian mines is also discussed and a trend for the future is proposed. The report then examines in broader aspects the world primary silver production and concludes, in the section on outlook, that the effective supply in primary silver will grow at a rate significantly lower than the growth rate expected for base metals. A cumulative deficit of some 900 million ounces is projected for the period 1975-1980 and a further deficit of some 1,100 million ounces if projected for the 1980-to-1985 period.

Jan 1, 1977

By D. A. Barr

High-grade gold-silver mineralization associated with electrum and argentite was discovered in a quartz vein at the Chappelle property, 273 km north of Smithers, B.C., in 1969 following a regional geochemical reconnaissance program in the Cassiar-Omineca Mountains. Subsequent exploration resulted in the discovery of numerous quartz veins with associated precious-metal values in a belt 17 by 3 km in area centrally located within Toodoggone Group volcanic and sedimentary rocks of Lower to Middle Jurassic age and a window of Takla Group volcanic rocks of Upper Triassic age. More detailed investigations, consisting principally of 5677 m of surface drilling in 57 holes and crosscutting, drifting and raising on Chapelle Vein A, has outlined a high-grade gold-silver-bearing shoot with a strike length of 200 m, an average width of about 3 m and extending to an average depth of about 40 m below surface.

Jan 1, 1978

By J. O?Shea

From the characteristics of the new (1976) electronic components and units that are being marketed, the author has tried to foresee the types and the performances of the near-future slope-monitoring equipment. Much-improved sensors, instruments and systems for pit use can now be developed - sun-powered telemetry remote stations are feasible, very sensitive as well as precise and drift-free liquid level inclinometers will be available, new techniques for distance measurement with lasers obviate the need for atmospheric corrections and the latest generation of desktop calculators have become easily programmed minicomputers. Thus, it is realistic to assume that fully automatic pit-slope monitoring systems will be operational in the foreseeable future.

Jan 1, 1978

By J. E. Terry

This paper outlines the steps that are being taken to close the gap between training and industry and indicates areas in which more work needs to be done. Although based on experience in the Maritime Provinces, it is applicable to industrial and educational studies across the length and breadth of Canada.

Jan 1, 1970

By H. C. Cooke

THE gold mining industry, in Canada as in other countries, has passed through trying times in the past year. The strains and stresses of war have drawn away much of its man-power, both from the labour and the management. The urgent needs of the war machine have greatly curtailed the amounts of steel and explosives that can be allotted to the mines; and the loss, by enemy action, of supplies of such essential things as rubber, bids fair to reduce operations still further, if not cripple them entirely in time. And, as if these difficulties were not enough, war on the psychological front has been declared on the gold mines. Earnest supporters of the war effort, well-meaning theorists, and perhaps others whose intent is less disinterested, have all combined to clamour against the continuance of gold mining. We have been asked, what is the use of taking gold out of one hole in Canada to put it into another in Kentucky. We have been assured that gold will never again have any value, except for filling teeth. We have been repeatedly adjured to look at Germany, how well it has got along without gold. We have been told that it is unthinkable, when this nation is girding her loins for war, that labour and materials should be diverted to this useless effort. Gold miners should be diverted to the base-metal mines, where they can produce something of real value to the war effort; or to war factories; or, in fact, almost anywhere, so long as they are got out of the gold mines. And, what has made the situation even more disturbing, it has seemed as if all this clamour might be convincing governments. In fact, as you all know, the government of the United States did actually take the step of ordering its gold mines to cease operations. Fortunately, however, for Canada, the facts that no large favourable effects resulted from that action, and that, in Canada, gold mining is a much larger part of the national economy than in the United States, have caused our government, so far at least, to avoid this drastic step. In talking about this, however, let me emphasize that I have no more inside information on the subject than any of you. Like Will Rogers, all I know is what I see in the papers.

Jan 1, 1943

By Peter C. Jones

The paper gives a broad view of the maintenance procedures at the Cassiar Asbestos Corporation property. Comparisons are drawn to indicate the changes in facilities and approach that have evolved over the last 25 years while coping with the northern British Columbia climatic conditions. Special emphasis has been placed on the importance of the support groups providing services for both the mine site and the town.

Jan 1, 1978

By P. A. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The recovery of cyanide from a gold mill solution containing high levels of copper (400 mg/L to 900 mg/L) using the AVR process was evaluated. It was determined that acidification to pH 2 to 3 provides a suitable balance between HCN generation, copper precipitation and acid consumption. A short pilot plant campaign showed that ~75% of the feed WAD cyanide was recovered while the remainder precipitated along with copper upon acidification. The acid consumption averaged 3.5 g H2SO4 per litre of solution. The copper precipitate, consisting mostly of CuCN and CuSCN, was readily separated from the solution by gravity. The volatilization of HCN in countercurrent packed columns averaged 98.7% efficiency. Reabsorption of HCN was practically 100% in NaOH solutions and slightly lower in a lime slurry. Basic volatilizer design parameters applicable to a large-scale operation were determined, including the Henry’s Law constant and the mass transfer coefficient of HCN gas.

Jan 1, 1998

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980