Search Documents

By T. E. Morimoto

Summary The Research Council of Alberta has made a series of tests with the cyclone washer to investigate the influence of the following operating variables: underflow apex diameter, .specific gravity of medium, pulp ratio, density distribution of the feed, and size analysis of the feed. The results obtained for all the variables studied, except size analysis of the feed, are included in this paper. The tests were made with smaller underflow apex diameters and lower specific gravity .suspensions than have been recommended by Cerchar for the sharpest separations. However, what is considered to be sufficiently good cleaning was accomplished with a suspension of 1.30 specific gravity and an underflow to overflow diameter ratio of 0.56. It was found that the sharpness of separation was not affected appreciably by variations in specific gravity of suspension or underflow apex diameter provided that the density of separation was within the normal range of washery operation. Cyclone performance was not too adversely affected by decreasing the pulp ratio. The minimum figure which gave reasonable separation was 4 to 1. The tests with various density distributions of feed revealed .that the degree of washing difficulty had no detrimental effect on the .sharpness of separation given by the cyclone. Introduction A major problem of the bituminous coal industry today is that of reducing the ash content of the finer sizes (minus 1/4-inch) of coal. This problem is particularly acute in Alberta, where, because of tectonic movement subsequent to deposition, the coals have been rendered friable, and bands of impurities have been intimately mixed with the clean material. As a consequence, most Alberta coals, as mined, contain a large proportion of fines and have a high inherent mineral-matter content. The advent of mechanized mining and stripping operations ?has further aggravated this problem.

Jan 1, 1952

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By W. S. Hargratt

THE present era of exploitation of the Little Long Lac and Sturgeon River areas commenced in 1925, when Beardmore Gold Mines started development of what is now the property of Northern Empire Mines. A shaft was sunk in 1927-28 and a very limited amount of underground work was carried out, following which the property was shut down. It remained idle until 1932, when Empire Star Mines, a Delaware Company, optioned the property. This Company formed the Northern Empire Mines Company, Limited, to operate the mine, and immediately instigated an aggressive programme of surface and underground development. By the summer of 1933, sufficient ore was indicated to justify the installation of a small mill. The decision was also reached to bring in electric power. A power-line was built from Hydro, the Ontario Power Commission's development on the Nipigon river, to the mine, a distance of approximately 50 miles. This work was entirely financed by Northern Empire Mines. Mill construction was commenced in October, 1933, and completed by March, 1934, thus making this mine the first producer in this district.

Jan 1, 1940

By Paul Clayton

Case Study ? Site: BMA Saragi Coal Mine Queensland Australia ? Model: Marion 8050 ? YOM: Mid 1970s ? Boom: 97M ? Bucket: Original capacity of 100 Tonnes upgraded to 125 tonnes at time of filtration upgrade. ? Apps: Swing, Hoist & Drag Gearboxes ? Oil: Oil Castrol Alpha TT1200 Viscosity of 1208 cSt @ 40° C (104° F) 720ltr Oil Volume Trial and Installation Justifications ? To reduce gearbox overhauls. Typical schedule being 5 years. ? Bucket upgrade from 100 tonnes to 125 tonnes. Increased gearbox demand and stress. ? Increase of overhauls out to 10 years + ? Saving per Dragline estimated to be US$8-10M in downtime and maintenance if successful. ? In compliance with BHPBilliton Global Maintenance FLAC program ? Fuels, Lubricants, Air and Coolants ? Cost Justification ? Downtime: 4 days ? Lost production: $420,000 ? Cost of parts: $162,000 ? Labour and misc: $41,000 Gearbox failure cost $623,000

May 1, 2008

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By D. Farrish, W. A. Grell

"IntroductionMost base metal mines sell their concentrate to a custom smelter. The two parties concerned therefore draw up a contract which would detail the conditions under which concentrate sales will take place. The contract will identify treatment and marketing charges (including escalations), deductions for metal losses in the smelter, pricing formula, timing of payments, penalties for deleterious elements, etc.An understanding of the smelter contract is important to the mineral processor, for it will determine how he operates the plant to maximize economic return.Description of Contract ClausesUsing copper concentrate as an example, the smelter contract generally contains the following three basic charges:I. Metal Deductions- as the smelting process does not recover all the metal contained;2. A Smelting Charge- expressed per ton of material to cover costs on the bulk material such as receiving, unloading, thawing in winter, sampling, roasting to drive off sulphur, smelting through the matte and blister stages to recover mostof the copper and precious metals;3. A Refining Charge- expressed per pound of copper.The following is a review in some detail of a number of clauses which could be considered typical of a treatment and marketing type of copper concentrate sales contract. Most normal considerations in an agreement could be covered by the following types of clauses.Terminology- covers definitions, units of measurement to be used (e.g. short tons, troy ounces, etc.), currency (Canadian dollars). The term ""unit"" may be defined - l OJo of a ton of concentrate, e.g. one unit of copper means 20 pounds of copper per short ton of concentrate."

Jan 1, 1989

By A. McLean, X. Men

"With high quality sulphide ores diminishing, nickel production from low-grade oxide ores becomes increasingly important and a major concern is the high sulphur level in the resultant ferro-alloy. So, desulphurization of the ferronickel becomes an important consideration. Red mud is a waste product of alumina industry and causes adverse effects on environment. In the present study, experiments were conducted to determine feasibility of using red mud as a major ingredient of refining fluxes for ferronickel desulphurization. In view of their influence on slag-metal separation, contact angle measurements between ferronickel alloy and molten slag made from red mud were also determined. INTRODUCTIONNickel is a very important metal that finds a variety of applications including consumer products, building, automotive and electronics. There are two kinds of ores containing nickel, namely oxide and sulphide ores. Anthony and Flett [1] reported that about 55% of the world’s nickel production originates from sulphide ores while the balance of new nickel is derived from oxide ores. However, oxide ores count for about 70% of the worldwide reserves. Apparently, oxide ores will play a significant role in the production of nickel in the future. Most of nickel produced using oxide ores is from pyrometallurgical processes namely ferronickel smelting or matte smelting. So, we can draw such a conclusion that using nickel oxide ores to produce ferronickel will become more and more important .Before used to make stainless steel or other materials, the ferronickel need pretreatment to remove impurities especially sulphur and phosphorus that will cause negative influence on the properties of steel product. Red mud is a by-product during alumina production. Usually, about 1 to 1.5 tons of red mud will be produced when we get 1 ton of alumina. About 90 million tones of red mud are produced every year in the world [2].Red mud is deemed as a toxic industrial waste which needs treatment before discharge because of alkalinity and chemical and mineralogical properties. Until now, the main means to deal with red mud are to store it in impoundments or dump it in the sea depending on local environment. Nowadays, how to recycle red mud has become a pretty hot topic around the world. The last 40 years have witnessed a lot of patent applications concerning the ways of red mud utilization. However, a little amount of red mud is consumed until now due to the limitations of recycling red mud."

Jan 1, 2012

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By D. V. Dorling, J. T. Bowker, J. A. Gianetto

Over the last few years, interest in the development and construction of large diameter, high pressure pipelines from the Mackenzie Delta in northern Canada and Alaska's North Slope has steadily increased as a result of the projected decline in recoverable natural gas from existing reserves in western Canada. The success of such enormous pipeline projects, which will require utilization of a strain-based design approach, is largely based on successful application of high strength line pipe steels, such as X80 and X100. To fully realize the economic benefits of high strength steels, welding processes and procedures must be developed to ensure that the requirements for high strength and good low temperature toughness are confidently obtainable in field girth welds used in the construction of such pipelines. This study aims to provide a better understanding of the factors that control weld metal strength and toughness for a series of mechanized X100 girth welds produced using a range of narrow-gap gas-metal arc welding procedures. The attainment of high yield strength (> 810 MPa) is considered to be an important target to ensure overmatching strength relative to the longitudinal property distribution of X100 line pipe steel. Some factors that have been considered in this evaluation include influences of gas-metal arc welding process variants (single and multi-wire) and changes in welding procedure specifications, including joint preparation. Key components of this work relate to the reliable measurement of weld metal strength variation through-thickness and as a function of position around the circumference of a given girth weld.

Jan 1, 2005

By S. R. McCutcheon, D. R. Lentz, W. S. Downey

"Abstract - The Little Falls member of the Nepisiguit Falls Formation is situated in the northern part of the Brunswick Belt of the Bathurst Mining Camp and has been interpreted as the distal equivalent of proximal tuffaceous rocks that host the stratiform Brunswick No. 12 and No. 6 Pb-Zn massive sulfide deposits. It comprises fine-grained, greenish-gray tuffaceous sandstone in the lower part, and coarse-grained, crystal-rich tuffaceous sandstone in the upper part. Petrographic evidence suggests that these rocks have a turbiditic origin. The Little Falls member is underlain by the Vallée Lourdes member, mainly composed of relatively shallow-water calcareous rocks, and is conformably overlain by Mn-rich sedimentary rocks, mainly red argillites that host the Tetagouche Falls Mn-(Fe) deposit. All these rocks are considered to belong to the Nepisiguit Falls Formation, part of the Ordovician Tetagouche Group. Whole-rock geochemical data from the fine-grained tuffaceous sandstone and coarse-grained tuffaceous sandstone indicate that the two units of the Little Falls member are distinct. Zr and TiO2 contents, and total rare earth element (REE) values are higher in the coarse-grained unit (average Zr/TiO2 = 0.040, average SREE = 247 ppm, n = 6) than in the fine-grained unit (average Zr/TiO2 = 0.048, average SREE = 158 ppm, n = 17), which can be attributed to the variation in crystal content between the two units. Both units are HREE-enriched and have elevated La/Yb relative to the typical Nepisiguit Falls Formation. Overall, the geochemical data combined with evidence from the bounding units suggest that the Little Falls member was deposited in relatively shallow water, possibly in a near-arc environment. The relationship of volcanic facies within the Nepisiguit Falls Formation and the geochemistry of these facies indicate strongly that fine grained, reworked tuffaceous rocks, regardless of whether they are the distal equivalents of proximal tuffaceous rocks, are not associated with the major ore-bearing horizons of the Bathurst Mining Camp. Sommaire - Le Membre de Little Falls de la Formation de Nepisiguit Falls se retrouve dans la partie nord de la Ceinture Brunswick du Camp Minier de Bathurst ou elle a été interprétée comme l’équivalent distal des roches tuffacées proximales hôtes des gisements de sulfures massifs de Pb-Zn stratiformes Brunswick No.12 et No.6. Il consiste en grès tuffacé à grains fins gris verdâtre dans sa partie inférieure et en grès tuffacé à grains grossiers riche en cristaux dans sa partie supérieure. Les données pétrographiques suggèrent que ces roches ont été déposées par des courants de turbidité. Le Membre de Little Falls repose sur le Membre de Vallée Lourdes, lequel consiste principalement en roches calcareuses déposées en eau relativement peu profonde; il est de plus recouvert en concordance par des roches sédimentaires manganifères, lesquelles consistent principalement en argilites rouges hôtes du gisement de Mn-(Fe) de Tetagouche Falls. Toutes ces roches appartiennent à la Formation de Nepisiguit Falls, laquelle fait partie du Groupe de Tetagouche, d’âge Ordovicien. Les données lithogéochimiques des grès tuffacés à grains fins et à grains grossiers indiquent que ces deux unités du Membre de Little Falls sont distinctes. Les teneurs en Zr et en TiO2, ainsi que la teneur totale en Éléments des Terres Rares (ÉTR) sont plus élevées dans l’unité à grains grossiers (Zr/TiO2 moyen = 0.040, SREE moyen = 247 ppm, n = 6) que dans l’unité à grains fins (Zr/TiO2 moyen = 0.048, SREE moyen = 158 ppm, n = 17), ce qui pourrait s’expliquer par la variation de la quantité de cristaux dans chacune de ces deux unités. Chacune de ces deux unités présente un enrichissement en ÉTRL ainsi qu’un rapport La/Yb relativement plus grand que ce qui est typiquement observé dans la Formation de Nepisiguit Falls. Les données géochimiques considérées conjointement à l’information provenant des unités adjacentes suggèrent que le Me"

Jan 1, 2006

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

By Y. Chengxian

Many factors about the HIC (hydrogen-induced cracking) resistance of pipelines are discussed in this paper. The main factors that influence the ability of HIC are environmental and material factors. The chemical compositions, non-metal inclusions and microstructure are discussed in detail, while a group of tests on HIC resistance are done according to varying C, S, Mn and P contents in pipeline steels, different experiment time and different strength to the coupon. It is concluded that decreasing the amount of C and S can obtain good HIC resistance; the test time has an effect on the different microstructure of X70; microstructure is the most sensitive factor for the initiation processes of HIC.

Jan 1, 2005

By A. V. Tarasov

There are still a number of copper smelters in the world using the roasting and smelting process flow diagram for treating sulphide raw materials. The technical, economic and environmental performance indicators of such operations are inferior to the respective indicators of advanced processes. First of all with respect to copper and sulphur recovery: 95% and 75% as compared with 98% and over 90%, respectively. Based on the studies of the single-stage smelting process to produce white metal and blister copper conducted during recent years an analysis of the feasibility of roastingsmelting technology improvement was carried out in the Gintsvetmet Institute to substantially increase the copper and sulphur recoveries. On the basis of this analysis, it was proposed to modernize the technology and equipment within the framework of the existing process flow-sheet. The proposed modernization implies an increase in the roasting temperature; higher desulphurization degree in the process of roasting; a number of modifications in the roaster design depending on the particular conditions of a given operation; addition of lime flux to the feed charge to roasting; and transition to combined calcium-silicate smelting slags. The metallurgical and energy computations made have indicated that the proposed modifications of the technology will improve the copper and sulphur recovery up to 98% and 90%, respectively. The required capital investments have been estimated using as an example a particular copper smelter, the payback period determined taking into consideration additional output, fuel saving and a reduction in fines for sulphur emissions. For comparison, the capital cost of a smelter modernization is given for change-over to basically new autogenous Ausmelt, Outokumpu and V anyukov smelting technologies.

Jan 1, 2007

By T. Banerjee, Y. Dumais, R. Lemire

"Agnico Eagle LaRonde produces over 300,000 ounces of gold annually, along with silver, zinc and copper by-products. The LaRonde plant consists of a conventional SAG and Ball mill circuit, followed by flotation. Load management is imperative for maintaining stability in grind size and ensuring consistency of the flotation feed. In flotation, the mass pull profiles of the cells and reagent dosage rates need to be managed to maximize recovery, while maintaining product quality. This is achieved by controlling the air, level and reagent addition set-points across the circuit. However, disturbances such as feed size distribution, ore hardness and mineralogy make it challenging to maintain efficient control using traditional control techniques. LaRonde therefore worked to develop a progressive control strategy, targeting stability and optimization. This started with a year-long instrumentation upgrade campaign, focusing on optimizing the performance and reliability of plant-wide instrumentation. The process was then optimized, leveraging AwaRE advanced controllers running in closed loop with PARC modules embedded within the PLC. The installation of 8 PFC cameras in flotation changed the flotation operation from a level and air control based strategy, to one that controls mass pull. This new control philosophy has allowed the plant to effectively manage mill load, improving grind size and providing increased throughput with better flotation performance.INTRODUCTION Background Since 2015, Agnico Eagle LaRonde has been conducting an optimization campaign to maximise the performance of plant assets leveraging instrumentation and control. The grinding and copper flotation circuits were identified as the areas having the greatest opportunities and value proposition for advanced control. A disciplined approach was followed to design and implement a progressive control solution to achieve operational excellence."

Jan 1, 2018

By Y. Chengxian, F. Yaorong, Xinzhe. L.

Many factors about the HIC (hydrogen-induced cracking) resistance of pipelines are discussed in this paper. The main factors that influence the ability of HIC are environmental and material factors. The chemical compositions, non-metal inclusions and microstructure are discussed in detail, while a group of tests on HIC resistance are done according to varying C, S, Mn and P contents in pipeline steels, different experiment time and different strength to the coupon. It is concluded that decreasing the amount of C and S can obtain good HIC resistance; the test time has an effect on the different microstructure of X70; microstructure is the most sensitive factor for the initiation processes of HIC.

Jan 1, 2005

By T. Y. Chong, J. A. Folinsbee

Since milling began in 1909, the PJV Dome mill has been expanded several times, to the current throughput of 11,500 tonnes per day. PJV recovers free gold using crushing and grinding followed by gravity concentration. The remaining gold in the gravity tails is recovered by cyanide leaching followed by Carbon-In -Pulp processing. Prior to 1993, cyanide tailings were impounded in the tailings pond where cyanide was allowed to degrade naturally. Effluent was discharged seasonally during the summer and early autumn to maintain the water balance. In 1993, an Effluent Treatment Plant (ETP) was designed and constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO SO2/Air cyanide destruction process was added to the ETP. Even though the ETP was successful in meeting the cyanide, metals and total suspended solids (TSS) discharge limits, often the treated effluent failed to pass toxicity tests. Following successful laboratory and plant scale testing, the addition of the chelant EDTA (ethylene diamine-tetra-acetic-acid) was commenced in the 1999 operating season. To date, discharged effluent has passed all toxicity tests. This paper describes the evolution of the ETP from its early conception to the various phases of upgrade needed to meet the MISA discharge limits.

Jan 1, 2005

By François Charette

High stress conditions in underground mines push the performance envelope of support systems to their limit. In weak rock masses these conditions lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock and support failure. In typical support systems, a combination of different reinforcement and support mechanisms provide the required convergence control and retainment. These systems usually involve a multi-pass support installation. The advantages of a single pass support system are investigated and several bolting combinations are compared. Criteria for design are reviewed and new criteria are proposed to include cost and effectiveness in commonly used engineering approaches. Field observation and testing is used to illustrate the difference between the proposed approach and more conventional systems.

Nov 1, 2011

Bahuerachi Project Characteristics Why it?s nicer at Bahuerachi Mexico is a mining country Low political, regulatory and trade risk Low social/permitting risk Proximity to infrastructure Road Power grid (8 km) Rail line (25 km) High grade zones (skarns), CRD and near surface oxide component are sweet spots to the overall system. Size of low grade system points to potential long mine life?and numerous new targets developing. Timelines-2006? 90 to 100 combined RC and core holes to go! MAIN ZONE Drilling ? Goat ?Finish Mid April ? Main Zone, going North, depth of testing dependent, estimated for May ? North Lobe-May ? Commission independent resource estimate by May 06 for results of first pass drilling to date ?tonnesand grades ?Main Zone Milestone. ? Continue infill or expanded drilling to July (minimum) ? 1stpass RC scheduled until September OTHER Targets ? Begin drill testing North Skarn target Mid-April, minimum 5 drill holes, 1,000 meters. Ongoing expansion of target with surface work (mapping) ? Road to Colome(Skarnin north of Main Zone) as part of porphyry program ? Tule(southern) porphyry and skarn system-soils and mapping OUTSTANDING events Metallurgical report on floating and leaching tests (Sulphide/oxides).

May 1, 2006