Search Documents

By S. Pauly, U. Kühn, J. Eckert, I. Kaban, G. Wiehl, F. Silze

In the present work, the effect of Ga on the wetting behavior of the Cu-rich braze filler CuGa10 (wt.%) on the steel 304L was investigated. For this, the macroscopic and microscopic effects governing the wetting of pure Ga, pure Cu and CuGa10 alloy (wt.%) on the austenitic steel were analyzed and compared. Contact angle and surface tension measurements were carried out by means of the sessile drop technique and, in addition, the phase formation at the interface was determined. Pure liquid Ga spreads on 304L, which supposedly is related to the formation of intermetallic Fe-Ga phases growing into the liquid Ga. Depending on the annealing time, FeGa3 and Fe14.5Ga12 were identified. In contrast, CuGa10 as well as pure Cu show secondary wetting on the steel surface. Especially, liquid Cu prefers to spread laterally and vertically along the grain boundaries of the steel substrate. In spite of rather similar mechanisms, CuGa10 wets 304L steel at lower rate than pure Cu above the liquidus temperature.

Jan 1, 2014

By E. Topuz, C. Duan

"INTRODUCTIONOperations research (OR) applications have experienced a substantial growth within the mining industry during the last three decades. The purpose of this paper is to present a summary of the results of a comprehensive survey of the application of various OR techniques to the major mining activities. It is hoped. through this sur vey , that the most widely used OR approaches, the important areas of application, and future trends have been identified.This survey included more than 500 articles published in this field in English since the late 1950s. Most of the relevant literature was found in mining publications, but, in terms of quality and originality, important applications were also found in literature not related to the mining industry. The sources constituted periodicals, proceedings research reports, and a few books. A listing of selected publications from which three or more articles reviewed in this survey appear is given at the end. Operations Research MethodologiesOperations research is concerned with optimal decision making in, and modeling of, deterministic and probabilistic systems that originate in real-life situation s. One basic feature of the OR methodologies is the attempt to optimize certain design parameters, subject to a set of constraints. This distinction has been employed in the survey as a guideline for selection of the techniques covered under the title "" OR methodologies"". The methodologies thus encountered in the literature are listed below. In a few cases, simulation has not been considered because it is not an optimization method per se."

Jan 1, 1989

By M. Phylli Bray

"Concurrent with the continuing demise of many Canadian mining towns is the rise of a new method of providing remote mine sites with a workforce. This is the Long Distance Commute (LDC) which uses commuter labour and requires no permanent settlements to support the mine operation. It provides a flexible and cost effective method of operation to the industry and relieves both governments and industry of the expense of building and maintaining mining towns. However, little attention has been paid to the effect on workers or their families of the LDC work schedule whereby workers spend a fixed number of days at the site followed by a fixed number of days at home. Off-shore oil rig experience would indicate that negative social impacts may be expected. Research leading to an understanding of the problems involved seems to be indicated. One innovative suggestion has been to use already established but dying mining towns as workforce pick-up points for new LDC operations further north.BackgroundUntil recently, mine towns were considered as a necessary component of mine development. This was a natural symbiosis resulting from the need to provide workforce accommodation close to isolated mine sites. The early mine communities in Canada were often just a huddle of shacks around a head frame. Gradually mining companies began to provide housing which varied from basic duplexes and quads in grid pattern layout to professionally planned and designed towns, either model company towns or the more recent suburbs-in-the-bush, the so-called ""instant towns"" of the postWorld War II era of resource development. The improvement in accommodation reflected the need to attract a stable workforce as mine operations became more sophisticated. City amenities were expected and offered in these mine towns as a way of encouraging a permanent community of mining families. Indeed in towns like Manitouwdage, Schefferville, and others, it was not unusual to find a significant percentage of two- and three-generation families apparently providing the permanent mining communities so desired by mine operators."

Jan 1, 1991

By J. A. Brown, F. P. Kerr, M. A. Archer

Extensive testwork on Global Atomic’s Dasa Project in Niger has been conducted at SGS Minerals laboratory in Lakefield, Ontario. Much of this testwork has focused on a two-stage counter-current leach as a means of improving leach efficiency and decreasing reagent consumption. The ore contains uranium mineralization requiring relatively high sulphuric acid concentrations during leaching to achieve acceptably high extractions. Excess free acidity in the leach solution may be utilized by recycling the high acid solution and contacting it with fresh ground ore. The resulting pregnant leach solution (PLS), now higher in uranium concentration and depleted in free acid, is forwarded on to uranium recovery by solvent extraction. The first stage residue proceeds to the second stage leach where fresh acid and oxidant are provided to leach the remaining uranium. This paper presents the results of the testwork conducted on both a Master Composite and Variability samples.

Jan 1, 2020

By Jacek Paraszczak

Possibility to move human workers away from dangerous places ?enhanced safety and improved working environment; ? Increase of actual operational time: ? Less losses due to shift changes, regulatory breaks, blasting periods, ventilation after blasting, etc.; ? Possibility to work in extremely dangerous conditions where man-operated machine could not be used (for example: ST-14 loader in backfilling operations in the Kemimine, following roof collapse). Reduction of the production cost through: ? Lower maintenance cost (less damage due to operator?s mistakes and no machine abuse); ? Higher productivity and effectiveness of the equipment (less machines to meet production targets, less operators required, lesser maintenance cost...). ? Although personnel health and safety are key drivers behind autonomous operation of mobile equipment in U/G mines, with significant capital and operation costs one expects to achieve: ? Productivity higher, or at least equal to that offered by man-operated equipment and systems; ? Lower production cost. Therefore, high effectiveness of the autonomous equipment is crucial to succeed.

May 1, 2010

By K. L. Boyd

"Can the increasing tonnages of ore and waste mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each stage of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in material handling from the mine to the mill, maximizing operating hours per year.RÉSUMÉ Le recours à des concasseurs plus grands et plus performants suffit-il à gérer l’augmentation du tonnage du minerai et des déchets que l’on extrait de nos jours ? Cet article examine les tous derniers modèles de concassage primaire et de grands concasseurs à cône. Il montre que, pour satisfaire aux exigences de production plus conséquente des exploitations minières existantes et nouvelles, il est important d’optimiser les taux d’utilisation à chacune des étapes du circuit de réduction de la taille des roches, en plus d’utiliser les concasseurs plus grands actuellement disponibles. L’objectif de cet article est d’aider les sociétés d’experts-conseils et les exploitants à sélectionner le meilleur équipement ainsi que des articles fabriqués sur mesure pour la manutention de la mine au concentrateur, en optimisant les heures d’exploitation par année.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications have since become available.The rock size reduction process from the mine to the selected milling process facility has not changed since a person first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages:• stage 1: mining (rock breakage and fragmentation);• stage 2: prescreening (scalping);• stage 3: primary crushing; and• stage 4: fine crushing (secondary, tertiary, and quaternary).Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments play a key role in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2017

By F. K. McKean

Introduction The present paper may be considered as a sequel to a paper, A Process for Cleaning Molybdenite .Concentrate, which was presented by the author at the annual meeting of the Institute last year. In that paper, a description was given of the laboratory work leading up to the adoption of a new process for treating complex molybdenite ores of the Molybdenite Corporation of Canada. A bare outline of mill performance with the new flow-sheet was included. With this writing, the purpose is to describe the highly interesting work of translating laboratory experience into mill practice, to show what changes were required in design to put the scheme on an operational basis, and to point out the gratifying improvements in mill products which resulted from the new procedure. The process has been placed in operation at the La Corne mine of the Molybdenite Corporation of Canada. This mine was operated during the war by Wartime Metals Corporation, and, earlier, by the Molybdenite Reduction Company, which installed a small plant. The property is situated on the highway from Amos to Val d'Or, Quebec. The claims held by the Company are at the boundary between La Corne and Vassan townships.

Jan 1, 1947

By S. Yadav, T. G. Murthy, C. Saldana

"An experimental study has been carried out in order to study the deformation of porous brittle materials under plane strain indentation. Gypsum, which is well known model system for understanding the behaviour of soft rocks, is used in this study. The effect of wedge angle is investigated in this research through this series of experiments, using wedges of 3 different apical angles. High-speed, high-resolution images are captured using a CMOS camera during the experiment. The images obtained are analyzed using a Particle Image Velocimetry (PIV) algorithm in order to obtain the evolving velocity, strain-rate and strain fields.INTRODUCTIONThe problem of indentation, which is usually referred to in the context of hardness testing is ubiquitous as a material characterization technique for a large class of solids. Mechanical properties of materials such as yield stress, flow stress, fracture toughness, elastic moduli etc. can be related to the hardness of a given solid. The indentation problem involves a given material or solid (whose properties are to be determined) indented by a relatively harder material (indenter) allowing the solid to undergo plastic deformation, which is then related to the yield stress of the material. The problem of indentation and its variants see many applications ranging from mining and petroleum industry, infrastructure industry, manufacturing, and biomedical sectors. Indentation has been extensively studied in metals, with accurate measurement of deformation parameters, stresses and comparison with analytical solutions. On the other hand, understanding of indentation in other class of solids such as cellular solids, porous solids, rocks, and soft solids is still nascent. In case of rocks, a comprehensive understanding of the indentation problem is very crucial because of the obvious applications in mining, petroleum and infrastructure sectors. The inherent porosity, the brittle nature of the rocks, adds to the complexity of indentation in these porous brittle solids. Various theoretical models with degrees of simplifying assumptions have been proposed to study the indentation in rocks. The most common model used in the study of indentation in rocks is a cavity expansion model, wherein a blunt indenter indenting into a rock is approximated with the expansion of cylindrical or spherical cavity in an elastic-plastic material. Complementary studies in understanding fracture initiation and propagation due to indentation has been largely based on the studies of traditional brittle materials such as glass."

Jan 1, 2015

By V. Gangrade

Recirculation is the major concern associated with the utilization of booster fans. In controlled recirculation, a portion of the return air is purposely mixed with the intake air and the mixture is directed towards a working district, while the air quantity and gas concentrations in the air are closely monitored and managed. The objectives of this study were to determine the gas concentration in intake and return airways during controlled recirculation, and to determine the recirculation fraction for multiple headings. Experiments were conducted in a laboratory model to determine the effect of controlled recirculation on the quality of air circulated through the working faces. Preliminary results showed that recirculation is beneficial to ventilation planning because it reduces the build-up of air contaminants at the working faces and reduces the overall power consumptions. The experimental results were used to quantify the recirculation fraction and to calibrate ventilation models of the laboratory model. These models are used to simulate the controlled recirculation and to predict the gas concentrations in multiple headings.

Aug 1, 2013

By Keith Donovan

Why are we here? Improve equipment performance & health ? Eliminate undesirable downtime and expensive secondary damage ? Maximize equipment life, optimize running costs (reduce costs) ? Improve safety and environmental performance ? Capture and consistently apply equipment knowledge ? Improve Proactive Maintenance processes & practices

May 1, 2009

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By F. G. Boehm, T. S. Golosinski, P. M. Tucker

"In an earlier paper(1) the visits to several European mines using the bucket-wheel excavator (BWE) technology were described. It was during this trip that information was gathered on some interesting developments related to this type of mining, taking place elsewhere. It was learned that an across-the-pit system (XPS) comprised of a BWE and stacker has been operating successfully in a Hungarian mine for some time. Also the use of stackers with 225 m long booms and draglines with 125 m booms and 125m3 buckets in Soviet mines was indicated. Such equipment could be of great value to some Canadian strip mines, in particular the equipment proven useful in severe climatic conditions of U.S.S.R., similar to those of the Canadian prairies.To follow up on this information a field trip to Hungary and the U.S.S.R. was organized by the Department of Mineral Engineering, University of Alberta, to study the applications and performance of the systems in question. Visited were the Thorez mine near Visonta, Hungary, U.S.S.R. Ministry of Coal Mining and Skotchinski Institute in Moscow, Karagandashakhstoi Institute (designers of Ekibastuz mines in the Kazakh Republic) and Kostenko mine in Karaganda, Vostsibgiproshakht Institute (designers of Irsha Borodinski, Kharanovski, Moguntski and Tugnuski mines in Siberia) and the eastern Siberian Unit of the U.S.S.R. Coal Mining Ministry in Irkutsk as well as Azeiski mine located some 250 km northwest of Irkutsk. The findings of this field trip are presented."

Jan 1, 1985

By J. Aiello

"A brief history of previous mining activity on Coal Mountain, near Corbin, British Columbia, is followed by a description of the steps leading up to the resumption of mining in /974 by Byron Creek Collieries. New developments, including a preparation plant, a rail spur and a totally enclosed facility, as well as operating techniques, are also discussed. IntroductionThe Corbin Mine of Byron Creek Collieries Limited is located in southeastern British Columbia, approximately 110 air miles southwest of Calgary (Fig. I), 15 miles south of Highway 3 via a newly constructed provincial road (Fig. 2). Development of the area began on July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J . Robert s, first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co. , after acquiring 15,000 acres of land in the area , began to develop a mine.F.J. Roberts was responsible for the construction of the 14-mile rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production.The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3), and production from 1908 to 1930 inclusive totalled 2,337,800 tons. This production was allocated to the mines as shown in Table 1. No.3, 4 and 6 mines were operated intermittently from 1931 to 1935."

Jan 1, 1980

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By C. J. Newman, D. J. Kemp, R. M. Sweetin

"The smelter is described by area; feed preparation, continuous furnace line, gas handling and auxiliary systems, blister refining, Hazelett casting of thin anodes, and scrap remelting. Early smelter campaign data is presented and compared to design. Some modifications to the basic design of the furnaces and gas trains are indicated, with their respective impacts on improving smelter performance.Plant compactness, the use of jumbo tanks, and a highly automated electrode handling system are featured in the refinery description, with brief coverage of the liberator and slimes leaching sections. Early experience in refining thin regular Hazelett anodes, and submersible pump recovery of raw slimes are relayed, together with automatic stripping from titanium blanks.Refinery tonnages and operating parameters are given showing the relatively trouble-free attainment of refinery design performance.IntroductionPrevious papers and articles ( 1), (2) ,(3 ) have described the metallurgical facilities serving the copper-zinc-silver Kidd Creek orebody located near Timmins, Ontario. For convenience a brief review of their mid-1983 operating status is presented.The concentrator, originally designed for 9,000 short tons, was commissioned in late 1966. It can now comfortably process over 13,000 metric tonnes per day largely as a result of the addition of a fourth circuit in 1978."

Jan 1, 1984

By Carlos Alberto Spier

The Águas Claras and Pico mines are two world-class, iron-ore mines hosted within Lower- Proterozoic banded iron-formations (locally known as itabirites) of the Minas Supergroup located in the Quadrilátero Ferrífero District, Minas Gerais, Brazil. The Águas Claras orebody consists of a 2,500 m long roughly tabular-shaped lens hosted within the dolomitic itabirite of the Cauê Formation. Dolomitic itabirite is the protore of the soft high-grade iron ore, which is the main ore type of the Águas Claras orebody, and represents more than 85% of the 284 Mt mined since 1973. Hematite is the main constituent of the iron ores. It occurs as martite, granular hematite and, locally, as specularite. Magnetite appears subordinately as relicts within martite and hematite crystals. Gangue minerals are very rare. These consist of dolomite, chlorite, talc and apatite and are especially common close to the contact with the protore. This virtual absence of gangue minerals is reflected in the chemistry of ores which are characterized by very high Fe contents (an average of 68.2% Fe). The Pico orebody is a continuous ~3,000 m long body of lenticular shape hosted within quartz itabirite, which is the protore of the soft high- and low-grade ores at the Pico mine. The soft high-grade ores, together with the low-grade ores, called iron-rich itabirite, are the main types of ores at the Pico mine, respectively representing approximately 51 % and 29 % of the reserves within the pit. The iron oxide mineralogy is the same as that of the Águas Claras mine, but in different proportions. Gangue minerals are very rare in the high-grade ores, but are slightly more common in the iron-rich itabirite. Quartz is the dominant gangue mineral, and is found with minor quantities of chlorite. The chemistry of the high-grade ores is characterized by high Fe contents (an average of 67.0 %) and low P, Al2O3, and SiO2 which are concentrated in the fines. Iron rich itabirites average 58.6% Fe and 13.5% SiO2.

May 1, 2003

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

Flotation works very well for particles that are typically in the range 20 to 150 µmin diameter, for base metal ores. In this range, it is possible to get quite high recoveries in conventional flotation machines. Outside this range, the recoveries decline progressively, whether it be with the very fine or the coarse end of the size spectrum. In this paper, the reasons for the drop-off in recovery are briefly reviewed, together with strategies for future work. Recent progress in the author's laboratory will be described. These include the Concorde Cell, which takes advantage of the high dissipation rates in the shock wave created when a gas-liquid mixture reaches supersonic velocities. The environment thus created is very beneficial for the flotation of ultrafines. For coarse particles, the reasons for the drop-off in recovery can be related to the highly turbulent nature of the pulp in a conventional flotation cell. To improve recovery, it is necessary to find a way of bringing particles and bubbles into contact in a quiescent environment. A new process for coarse particle flotation will be described, in which a fluidized bed is created in the flotation cell. The flow conditions are very gentle, and the high solids concentration leads to rapid rates of capture of the particles. Experimental results are presented. It is apparent that the maximum floatable size for coal and minerals can be increased by a factor often over the limits found in current practice. Advances

Jan 1, 2009

By Hani Henein

Most metals and alloys processed undergo a solidification processing step. Increasingly, there is a growing number of solidification processing routes that involve rapid solidification of the alloy. These include strip casting, high pressure die casting, 3D printing, and atomization for the production of powders or spray formed parts. By contrast, there are few experimental techniques developed to study the solidification path of alloys during rapid solidification. Amongst these laser melting and solidification, Electromagnetic Levitation (EML) and Impulse Atomization (IA) are the most prominent. Of relevance is the formulation of the solidification path of an alloy and the resultant identification and quantification of metastable phases and their relationship to processing conditions. This typically involves the understanding of the interplay between undercooling and cooling rate for the various phases that form. This presentation will outline some of the methodologies developed to quantify phase fractions and their solidification path as a function of processing conditions using EML and IA.

Jan 1, 2016