Search Documents

By R. H. Chambers, L. Alderman

"The paper is introduced by an examination of the factors which have led to the present world-wide interest in charging preheated coal to coke ovens. Various possible methods of preheating and charging the coal are considered and reasons are given for the adoption of the methods chosen. The design of the pilot preheating plant for the British Coke Research Association is discussed and its influence on the design of the commercial units for the South African Iron and Steel Corporation's plant at Pretoria and the British Steel Corporation's plant at Beighton are explained. Operating procedures on the pilot plant are described, particularly with regard to the charging of the preheated coal. Design features of the commercial installations, engineered by Simon-Carves Ltd., are explained with emphasis on the built-in safety of the control system of the preheating plant, and the particular problems associated with the erection of such plants on working coke oven batteries. Commissioning and operating procedures are described and the problems associated with the integration of the preheating plant into the normal pushing schedule of the plant are discussed. Preliminary operating results with regard to the effect of preheating on coal throughput on the commercial plants and on the properties of the coke produced are given."

Jan 1, 1972

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924

By A. J. Macdonald

Gold deposits hosted by banded iron formation (BIF) in Ontario exhibit a marked association with localized zones of deformed and hydrothermally altered BI:F . Secondary sulphides and carbonates are conspicuous. Proposed carbonate-facies IF , or exhali tes, such as green carbonate in the Larder Lake camp and ankerite veins in the Porcupine Camp are structurally controlled, hydrothermally deposited zones of carbonate replacement and fissure filling. Gold precipitation from hyd r othermal fluids in strain-generated conduits may be due to (a) plating upon secondary sulphides, (b) pH change due to carbonatization of BIF or (c) destabilization of gold in solution due to sulphidation of BIF .

Jan 1, 1984

By Joël Kapusta

La pyrométallurgie du cuivre est essentiellement une chaîne de trois étapes successives d’oxydation préférentielle du fer et du soufre et des impuretés moins nobles que le cuivre qui sont contenues dans le concentré de cuivre issu de l’usine de concentration du minerai, aussi appelée concentrateur. La Figure 1 illustre la chaîne complète d’élaboration du cuivre depuis la mine jusqu’au cuivre pur. La voie hydrométallurgique traite le concentré par lixiviation, c.à.d. par dissolution en phase aqueuse à température typiquement inférieure à 100 ou 150⁰C, alors que la voie pyrométallurgique traite le concentré par fusion à température de l’ordre de 1200 à 1300⁰C.

May 2, 2024

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Dialkyl dithiophosphinates are a unique class of collectors used in the flotation processing of Cu- Au, complex polymetallic, and precious metal ores. They are known to exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive HSE profile. Historically, for most reagents used in flotation, practical methods of chemical usage have preceded detailed scientific understanding of how they work; this applies also to dithiophosphinates. Recently, however, the research community has shown significant interest in this chemistry, and numerous studies have been conducted to understand the fundamentals of interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized by drawing on concepts and insights from coordination chemistry. A comparison between the interactions of dithiophosphinates and dithiophosphate analogues with various minerals and metals is also made throughout. We believe that such a critical analysis/overview will be invaluable in identifying gaps in knowledge regarding this important set of compounds, which in turn may provide a basis for the design of studies that can advance understanding of their flotation performance. INTRODUCTIONDialkyl dithiophosphinates are an important member of the class of thiophosphorus compounds that are widely used in flotation beneficiation of base metal sulfide and precious metals ores. Ore flotation studies and plant practice experience have demonstrated their unique properties compared to the traditionally used sulfide collectors such as dialkyl dithiophosphates (their closest analogues) and xanthates. The predominant dialkyl dithiophosphinate used in the industry today is sodium diisobutyl dithiophosphinate (a.k.a. DIBDTPi; AEROPHINE® 3418A1 introduced by American Cyanamid in the late 1970s; Figure 1). The widest application of AEROPHINE 3418A is found in complex polymetallic ores of Cu-Pb-Zn-Ag, Pb-Zn-Ag, and Cu-Zn where it has demonstrated improved recoveries (and flotation rates) of sulfide minerals of Cu, Pb and Ag and selectivity against sphalerite, iron sulfides, and penalty elements (Mingione, 1991). More recently, it has also been used as a collector in the processing of Cu, Cu-Ni, and Ni ores (Guitard et al., 2015) and Cu-Au ores (Dunne, 2005). In general, it is considered to possess the collecting power of xanthates together with the selectivity (against pyrite) of dithiophosphates (Hope et al., 2003a, 2003b), while requiring lower dosages than those reagents (Guitard et al., 2015). AEROPHINE® 3418A has also found an important place in several targeted formulations to improve flotation performance. Other benefits of this reagent include higher flotation rates, having a better HSE (health, safety and environmental) profile2 compared to xanthate, and exhibiting resistance to hydrolysis and oxidation (Guitard et al., 2015). Compared to diisobutyl dithiophosphate (DIBDTP), which is known to contribute significantly to frothing (often leading to over-frothing), AEROPHINE® 3418A is observed to be froth neutral (i.e. it does not alter the existing froth characteristics). As is the case for other flotation reagents, the design and application of AEROPHINE® 3418A has preceded understanding of its behavior at a fundamental level. Recently, there have been numerous fundamental and application studies designed to develop a better understanding of its interaction with sulfide minerals and precious metals. This should help in optimizing its application in flotation and provide a basis to better rationalize its unique selectivity and activity characteristics. Past studies on the interacti"

Jan 1, 2016

By Shawn Harvey

HIGHLIGHTS of STAR DIAMOND PROJECT Initial underground bulk sample 4,048 ct / 25,253 tonnes: US$135/carat: 3,050 ct March 2005 $116 million financing: Newmont takes 9.9% SGF Prefeasibility study commenced on Star Merger with Kensington: 42.245% FALC-JV Voting agreement with Cameco in FALC-JV November 2005 $120 million financing: Newmont maintains 9.9% SGF Diamond valuation: 5,950 ct/ 36,529 tonnes: US$135/carat

May 1, 2006

By M. J. Davie, D. S. Ross

"The successful design of a new mine water pumping system is in part dependent upon the accuracy with which the operating conditions can be forecast. This paper outlines the data which should be obtained on water quantity and quality. Methods of modifying the quality are also discussed. Some pumping systems for disposal of sludge are described, citing operating examples. The various types of mine dewatering pumps are described in terms of design characteristics as they affect operating efficiency and installation and maintenance costs. Piping system parameters are outlined. Finally, a hypothetical case study of pumping from a depth of 3,000 ft is assessed, with particular reference to capital costs.IntroductionMany mine operators would agree that the pumping system usually receives a low engineering priority during the design stage, and as a consequence causes some of the most frustrating problems during production. For a ""dry"" mine (up to 200 gpm), design of the pumping system may indeed be simple, but outside of the potash industry such mines are not common. For ""wet"" mines, the pumping system is important because it significantly affects the initial capital and on-going energy costs of the mine and, in the area of sludge disposal, the working conditions and production costs. Indeed, a failure in the pumping system usually has serious, and sometimes disastrous, consequences.The intent of this paper is to outline the factors which should be considered in the design of a pumping system and to describe the types of pumps used in mine dewatering and relate them to practical operating systems."

Jan 1, 1980

By A. Ockewitz, A. Trondl, D. -Z. Sun

"Numerical simulation of extrusion processes offers an efficient method for tool design and optimization of geometries and properties of extruded parts. However, until now there are few systematic investigations about influences of material model and different parameters e.g. for friction and thermal processes on calculated local and global responses. Since extrusion processes are essentially influenced by friction between billet and extrusion tools, new friction tests were performed in this work to develop a reliable friction model. Compression and torsion tests were performed at different temperatures and velocities to calibrate the material model for extrusion simulations. Extrusion processes for circular rods and U-profiles were conducted at TU Berlin with backward and forward extrusion for different extrusion ratios, billet temperatures, product velocities and cooling conditions. This work focuses on numerical simulations of the extrusion tests with the FE code HyperXtrude. Based on the calculated distributions of local strain, strain rate and temperature the recrystallized volume fraction and grain sizes were calculated with empirical models and compared with the experimental results from optical micrographs and EBSD scans. The calculated total and friction forces and temperatures were compared with the experimental results and the deviations between experiment and simulation were analyzed.INTRODUCTION Extruded aluminum components are widely used in vehicle constructions due to light weight and manufacturing consideration. Local mechanical properties in the components are inhomogeneous as a consequence of the spatial distribution of microstructure which is influenced by numerous factors like material composition, temperature, tool design, friction, extrusion ratio and speed during the extrusion process. For the optimization of the extrusion process with regard to all these factors numerical simulation can be an essential tool. Based on results of finite element simulations of the extrusion process the microstructure in the extruded components can be predicted and then the resulting mechanical properties can be numerically determined instead of by costly trial and error methods. The aim of the work presented in this paper is the development of a numerical method for the simulation of extrusion processes with modeling of microstructure."

Jan 1, 2018

By R. I. Iacobescu, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, P. Knops

In this work, we explore a novel mineral processing approach using carbon dioxide to promote mineral alterations that lead to improved extractability of nickel from olivine ((Mg,Fe)2SiO4). The precept is that by altering the morphology and the mineralogy of the ore via mineral carbonation, the comminution requirements and the acid consumption during hydrometallurgical processing can be reduced. Furthermore, carbonation pre-treatment can lead to mineral liberation and concentration of metals in physically separable phases. In a first processing step, olivine is fully carbonated at high CO2 partial pressures (35 bar) and optimal temperature (200 °C) with the addition of pH buffering agents. This leads to a powdery product containing high carbonate content. The main products of the carbonation reaction include amorphous colloidal silica, chromium-rich metallic particles, and iron-substituted magnesite ((Mg1- x,Fex)CO3). Carbonated olivine was subsequently leached using an array of inorganic and organic acids to test their leaching efficiency. Compared to leaching from untreated olivine, the percentage of nickel extracted from carbonated olivine by acid leaching was significantly increased. It is anticipated that the mineral carbonation pre-treatment approach may also be applicable to other ultrabasic and lateritic ores.

Jan 1, 2014

By Chas Kemsley

NO. 6 shaft at Dome Mines, Limited, is an internal shaft going down vertically from the sixteenth, or 2,000-ft., level to the twenty-ninth, or 4,000-ft., level, with loading station and sump below this. It is located approximately 4,600 feet east of No. 3 shaft, the latter being Dome's main shaft through which ail ore, men, and material are handled. The decision to sink this shaft was made in May, 1935, and work was commenced almost immediately. To reach the site of the new shaft, 3,100 feet of cross-cutting, and 1,400 feet of slashing to widen existing cross-cuts, was necessary. On account of the long haul and the large amount of material to be handled, trolley haulage was decided upon and installed as soon as possible to facilitate the removal of waste rock from the crosscut and other necessary excavations. Figure 1 shows a cross-section of the cross cut and the manner in which the trolley wire is supported and guarded. For hanging each individual cross-piece, two holes are drilled into the roof and filled with snug-fitting wooden plugs. Into these, %-in. ragged hanger bolts arc driven by means of a stoper. The bolts are of various lengths to allow for irregularities in the face of the rock, and they have sufficient thread to permit several inches of adjustment for proper alignment of the cross-pieces. These hangers are spaced at 8-ft. intervals except at the curves, where 5-ft. spacing is used. A 2 in. by 6 in. cedar plank is fastened to the cross-pieces directly over the centre of the track. To this the trolley-wire supports are bolted, and 1 in. by 10 in. cedar boards are nailed on each side to act as guards. Two power-supply cables, one telephone cable, and one .Y2-in. conduit lighting circuit are also supported on the trolley-wire hangers, as shown in Figure 1. A 20-in. ventilating pipe and a 10-in. air line are placed as shown, thus acting as a guard to prevent workmen from walking on the track.

Jan 1, 1938

By Timo Heikkinen

We have read, with great interest, Mr. Crocker's article on "Recent Trends in Autogenous Grinding," published in the October issue of The Canadian Mining and Metallurgical Bulletin. Referring to our paper, "Two-Stage Autogenous Grinding Investigations at Outokumpu," we can now report that last August we changed to this method at the Keretti concentrator. Prior to the conversion, the Keretti plant (see flow-sheet, Figure 1) had two primary rod mills, 6 ft. in diameter and 12ft. in length, in open circuit, followed by four secondary 9-by 12-ft. pebble grate mills in closed circuit with rake classifiers. Last summer, wl1en the Since August, grinding has been successfully carried out autogenously in two stages, with two mills being employed in the primary stage and four in the secondary. The size of the pebbles in the secondary mills is about the same as earlier -l V: i to 3 inches (Figures 4 and 5). Also, we generally prefer two-stage grinding to single-stage grinding because, in the former,

Jan 1, 1964

Phelps Dodge has recently operated a commercial scale, super fine grinding circuit of copper concentrates for use in a medium-temperature pressure leaching process. Two 355 kW vertical stirred mills were installed in series, targeting a grind of 80% passing 7.5 µm and 98% passing 15 µm as outlined in Phelps Dodge's concentrate leaching patent portfolio. This paper details the operation and results of the test program at Bag dad, as well as some of the operating challenges encountered.

Jan 1, 2007

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By S M. Roscoe

Relationships of Noranda sulphide deposits to volcanic rocks are reviewed and chemical variations within the volcanic sequence are described. The assemblages of minor elements in the pyrites and pyrrhotites of the Noranda and l\llatagami deposits are similar and are characterized by a high content of cobalt, tin and other elements. Isotopic compositions of lead, other geochronological data and stratigraphically disposed zonal distributions of sulphides and minor elements indicate that the deposits were formed prior to folding and metamorphism. Lead isotope data indicate that the Matagami deposits, and several others, were probably formed about 2.95 x 109 years ago and that the Noranda deposits may be about 50 million years younger. The volcanic sequence at Noranda is younger than the thick sequences bordering it on the east and on the west. The relationships are consistent with the hypothesis that these strata-bound sul1>hide de-posits are coeval with their associated volcanic rocks. T HE writer has been engaged in a metallogenic study of the region between Sault Ste. Marie and Chibougamau. An essential objective of this study is the classification of mineral deposits with regard to their composition, form, geological

Jan 1, 1965

By van der Meer. F. P.

High Pressure Grinding Roll (?HPGR?) technology is applied in a broadening range of minerals processing applications for relatively wet or moist materials. HPGR grinding of dry material or involving drying and air classification is more common, for example in cement manufacturing. A number of minerals processing plants are also operating with dry material, either due to process reasons, such as considerations of preceding or subsequent process stages, or as dictated by local conditions of arid areas and scarcity of water. The present world-wide expectation of decreasing availability of water supply urges us to look for alternatives that minimize water consumption. Recently established and envisaged future HPGR applications with dry ores have indicated that the technology of dry crushing and classification as practiced in cement and limestone grinding can be applied in minerals processing. Moreover, dry technology could very well be applied for generating a final fine product at sizes near or below 100 microns, as may be required for beneficiation by, for instance, flotation, magnetic separation or tank leaching. Dry HPGR grinding requires special attention in maintaining suitable process economics, when considering power input in grinding, drying and classification. In some cases, HPGR capacity and roll surface wear life may be negatively affected by a lack of moisture in the feed. This publication summarizes some of the features of, and experiences in dry HPGR applications. This includes design aspects of the classification system and discussion of the wear protection of the roll surfaces. The paper also includes examples of operational experiences of dry practices in minerals processing and cement plants.

Jan 1, 2012

By M. A. Bergougnou, I. Inculet, K. I. Burgess

This paper describes the electrostatic methods of separating various minerals, reviews the principles of fluidization and outlines the technique of electrostatic sorting in fluidized beds. The application of the method to the benefication of coal is emphasized.

Jan 1, 1970

By F. Qi, T. Frišcic, C. Mottillo

"One of the principal goals of modern industry is to minimize the environmental impact and increase the materials- and energy-efficiency of transforming raw materials into valuable products. This paper will highlight our latest laboratory-scale research in low-energy, low-solvent reactivity of metal oxides and their conversion into popular metal-organic frameworks (MOFs), zeolitic imidazolate frameworks (e.g. Basolite® Z1200 component ZIF-8), and metallodrugs (e.g. bismuth subsalicylate, active component of Pepto-Bismol®). Mechanochemical ion- and liquid-assisted grinding (ILAG) and ""accelerated aging"" techniques will be presented, along with novel low-energy and solvent-free approaches, inspired by geological weathering processes, for converting metal oxides into metal-organic materials. INTRODUCTIONThe development of environmentally-friendly processes, which would in the same time be more materials- and energy-efficient than the existing ones, is one of the central concerns of modern chemical research. In that sense, the focus of the chemist has been mainly on the preparation of carbon-based organic molecules and adaptation of traditional organic synthesis to the recently delineated ideals of Green Chemistry. However, there is a growing realization within the chemistry community that significant energy, materials, and ecology-related benefits can be achieved and, indeed, targeted in the transformations of materials that are typically associated with inorganic chemistry and minerals processing. The principal aim of this highlight contribution is to illustrate how, through the use of approaches associated with solventfree chemistry and mechanochemistry (James et al., 2012), one can develop a clean and efficient system of chemical and materials transformations involving oxide precursors that normally belong to the realm of inorganic chemistry and mineral processing. In particular, this contribution will provide an overview of the recently developed mechanochemical and solvent-free reactivity of metal oxides towards small organic molecules. These mechanochemical reactions, including the methods of liquid-assisted grinding (LAG, Frišcic & Jones, 2009) and ion- and liquid-assisted grinding (ILAG, Frišcic, 2010), have so far provided a radically different means to construct advanced metal-organic materials (e.g. porous metal-organic frameworks, [MOFs] or metallodrugs) by rehabilitating metal oxides as precursors, eliminating the use of bulk organic solvents, and avoiding the use of high temperatures."

Jan 1, 2012

By John H. Morris, R. Gwilym Roberts

"The Upper Beaver Mine, Kirkland Lake, Ontario, is a copper-gold deposit in mafic flows and sedimentary rocks. The deposit consists of a number of orebodies of two types: copper- and gold-bearing chalcopyrite-pyrite-magnetite ore; and gold-bearing quartz veins. Chalcopyrite-pyrite-magnetite ore occurs in two structural forms: as cherty interflow material in coarse clastic roks underlying flows; and as veins. Both sedimentary and vein ore occur in each orebody. The goldbearing quartz veins occur in interflow sedimentary units and at the contacts of oligoclase porphyry dykes.The deposit is in a localized, volcanic-sedimentary basin which began to develop during the emplacement of the upper units of the pyroclastic and sedimentary Gauthier Group, and continued to the early mafic flow activity of the overlying Kinojevis Group. The formation of the volcanic-sedimentary basin is ascribed to the D0 deformation. The deformation is significant in terms of the structural configuration in the mine area, and may be significant regionally, but this has not been demonstrated. The early deformation was followed by two tectonic deformations. D 1 is associated with a penetrative mineral foliation, axial planar to upright mesoscopic folds and striking parallel to the trend of regional fold structures. Mesoscopic flexural-slip folds, kink folds and fracture-crenulation cleavage are attributed to the D2 deformation. It is probable that no large-scale fold structures are associated with the D2 deformation. The gold-bearing quartz veins were folded during the D1 deformation.The close spatial relationship of copper-gold, chalcopyritepyrite- magnetite veins with chalcopyrite-pyrite-magnetite in cherty inter flow material is strong evidence for the derivation of the veins from the sedimentary ore by hydrothermal, metamorphogenic processes. By analogy, it is suggested that the gold-bearing quartz veins were formed by similar processes."

Jan 1, 1982

By R A. Burwash

In the Yellowknife geologic province, 2,600-million-year-old granites are cut by three sets of diabase or gabbro dyke : (1) large dykes striking 70°E to E-W, (2) rare dykes striking N-S to 30°E and (3) an abundant swarm striking N 10°-300W. Preliminary potassium-argon dating has been carried out on whole-rock samples of the chilled margins and coarse centers of the dykes, and on mineral separates from the dykes and contact aureoles. Data from seventeen dated samples suggest that the dyke sets were intruded during three periods of basaltic magmatism -2,200, 1,500 and 1000 million years ago. The two earlier periods closely follow the time of emplacement of granites in the Yellowknife and Churchill geologic provinces. The latest diabase dykes occurring in the Yellowknife province are temporally related to a widespread basaltic magmatism, for which the term Keweenawan is not appropriate. D DRING the past ten years, methods of physical age determination have been widely applied to date the time of intrusion or metamorphism of Precambrian rock

Jan 1, 1963

By M. S. Badollet

"DURING the past five years, production of asbestos fibers has increased in all countries that list asbestos as one of their mineral resources. Despite the many small mines that have been opened in Canada, United States, Mexico, South America, Italy, South Africa, Australia, Yugoslavia, and Rhodesia, the supply still does not meet the demand. It is estimated that total 1952 world production of asbestos fibers of all varieties approximated 1,600,000 tons, with Canada supplying 966,382 tons (I), or 60 per cent of all fiber mined.Asbestos fiber brokers continually are offering odd-lot samples of chrysotile, amosite, crocidolite, tremolite, and anthophyllite fibers to manufacturers, •quoting fantastic prices for tonnages •varying from just a few to 50 or more in a month. In many cases, the samples are not properly graded and contain quantities of rock impurities and finely ground dust.When vendors submit samples of asbestos fibers, the manufacturer should consider• them in terms of price, quality, quantity, and as possible substitutes for fibers currently used in his products.Grading of these odd-lot fibers in most cases has been poorly done, with resultant non-uniform fiber lengths. In some instances, a number of miscellaneous lots of fibers have been .blended for sale. This blending produces a fiber that is difficult for the manufacturer to accept as a substitute for the well-standardized Canadian fibers."

Jan 1, 1953