Search Documents

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

By A. J. Miller

Estimates of interstitial water saturation derived from capillary pres-sure data are compared with residual water saturations found by the analysis of cores out in oil-base drilling fluid. A theoretical explanation for the high-rate of water production from the Bellshill Lake Field is proposed, based on the interpretation of the capillary pressure data.

Jan 1, 1960

Who is CIBC? ? Canadian Imperial Bank of Commerce (?CIBC?) is a leading North American financial institution. ? Total Assets: US$315 billion ? Market Capitalization: US$29 billion ? CIBC comprises three strategic business lines: ? CIBC Retail Bank ? CIBC Wealth Management ? CIBC Wholesale Bank ? CIBC Wholesale Bank is a leading North American investment bank with niche capabilities in Asia, Australia & Europe. ? 1,000 + employees around the world ? Product range includes: Mergers & Acquisitions advisory and financing, Equity and Debt issues, Merchant Banking and Strategic Lending ? CIBC is ranked as the #1 investment bank in Canada across most of its key products and industries ? #1 Equity Underwriter in Canada ? #1 Mergers & Acquisitions Advisor in Canada

May 1, 2010

By J. B. Mawdsley

Introduction The writer was instructed to visit the Chibougamau region during the field season of 1927 and report on the mineral discoveries that had been made there since 1911. lt was deemed advisable to obtain detailed information regarding the rocks underlying the area in the vicinity of these recent discoveries. Accordingly an area 60 square miles in extent was mapped. The outcrops were studied along the water courses and along bush traverses spaced at half-mile intervals between these water courses. The completion of the rest of the summer's programme allowed only three weeks for this work. lt is from this small, mapped area, and this necessarily cursory survey, that the material for this paper was obtained. Location And Means Of Access The name Chibougamau district is applied loosely to an ill-defined area of about 1,000 square miles lying mostly north and west of Chibougamau lake in the Province of Quebec. The lake is approximately half way between lake St. John and James bay. It lies 150 miles north of the Canadian National railway and 40 miles south of Mistassini?lake.

Jan 1, 1928

By V. I. Lakshmanan

Recycling helps to save energy and is good for the environment. It is also important for preserving the limited natural resources. In addition, recycling creates economic benefits and frees up space at the landfill sites. Process Research Ortech Inc. (PRO) has conducted extensive testwork in the area of waste processing and recycling. A process was developed for the recovery of Zinc from galvanized steel by alkaline leaching followed by solvent extraction and electrowinning. Extensive testwork has been conducted at PRO to obtain a useful by-product from rice husk. Rice husk was combusted in a gas/solid reactor to obtain an environmentally acceptable amorphous silica ash suitable for use in high strength concrete. In another development, vanadium was recovered from fly ash by separating carbon first, followed by alkaline pressure leaching, solvent extraction and precipitation. PRO has also developed an environment friendly process for treatment of industrial wastewater for its reuse to obtain zero or minimal effluent discharge. In this paper, four case studies related to recycling of zinc scrap, controlled combustion of rice husk, processing of fly ash, and reuse of waste water will be discussed.

Jan 1, 2011

By J. Ambrose, R. W. Zimmerman

"Shales are highly anisotropic in their mechanical behavior. The strength ( ??1) of anisotropic shales depends not only on the magnitude of the other two principal stresses ( ??2, ??3), but also on the bedding plane orientations (?) relative to the principal stresses. In this study, the role of the intermediate stress ( ??2) on the strength of shale is evaluated using new data from triaxial compression and extension tests. To understand the failure behavior of shales, we have carried out triaxial compression tests ( ??1 > ??2 = ??3) on two organic rich mudstones, at different confining stresses and loading angles. We first fit the triaxial compression data with Jaeger’s plane-of-weakness model, and find that the model is able to represent the strength behavior of anisotropic shales reasonably well. We then carried out five triaxial extension tests ( ??1 = ??2 > ??3) for a high strength-anisotropy shale, and two extension tests for a low strength-anisotropy shale. Results from the compression and extension tests for failure along the weak plane shows that the role of ??2 is not significant for weak plane failure. However, for the low strength-anisotropy shale, the failure strength of the intact rock (i.e., at ??= 0o and 90o) for compression and extension tests were significantly different. This indicates that for intact rock failure, the role of ??2 is important and cannot be ignored.INTRODUCTIONFor many years, various researchers have studied the roles of ??2 for failure of isotropic rocks. (Mogi, 1967 and 2007; Colmenares and Zoback, 2002; Al-Ajmi and Zimmerman, 2005 and 2006; Haimson, 2009; Ma and Haimson, 2012). The findings from these studies show that the effect of ??2 on the strength of isotropic rocks is generally significant, and cannot be ignored.Since the role of ??2 in the failure of isotropic rocks was recognized, other researchers attempted to extend some of these isotropic failure criteria to anisotropic rocks, but with limited success (e.g., Tiwari & Rao, 2007; Singh et al., 1998; Zhang and Zhu, 2007; Pei, 2008). Smith and Cheatham (1980), on the other hand, conducted true-triaxial experiments on the Green River Shale and used a J2-I1 type relationship to predict the strength behavior, but without considering the effect of the three-dimensional orientation of the weak plane on strength. Therefore, unlike for the case of isotropic rocks, additional studies need to be done to determine the role of 2 on the failure of anisotropic rocks."

Jan 1, 2015

By A. Zarei-Hanzaki, S. M. Fatemi-Varzaneh, M. Haghshenas

The microstructure in modified semi-solid ALTHIX (A356) alloy consists of aAl phase with Al/Si eutectic structure. Silicon phase in eutectic structure is coral like with fine fibers. The lack of good ductility in this alloy is related to the presence of silicon fibers. Accordingly many investigations have been recently conducted to modify the Si morphology through Thermomechanical processing on this alloy. In the present work an ALTHIX (A356) alloy was deformed at 450°C, 500°C and 540°C through different strain rates. Consequently the silicon fibers were broken into small particles. The results indicated that the Si particles may coarsen according to Ostwald ripening mechanism at 540°C deformed by rate of0.0005 sec-1 & 0.0001 sec-1-

Jan 1, 2006

By Courtney E. Cleveland

THE gold deposits of the Pioneer and Bralorne mines, in the Bridge River district of British Columbia, are closely associated with a long, narrow intrusive body of extremely variable composition, outcropping on the northeast side of Cadwallader creek and lying almost entirely within the property boundaries of the two companies. Other masses of the same type of intrusive rock are found in the district, more or less along the line of the main axis of the Pioneer-Bralorne in trusive, and have associated with them variable amounts of gold-quartz mineralization (Figure 1). The ore deposits of the district have been the subject of investigation by officers of the Geological Survey of Canada at various times during the past 25 years, and articles on the geology and mines of the district have been published by various individuals in technical journals. A list of the more important re-ports follows: SELECTED BIBLIOGRAPHY

Jan 1, 1938

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987

By J. R. Levin, E. J. Schelter

"We present some of our recent efforts in the development of predictive, directed oxidation chemistry of cerium(III) complexes under non-aqueous conditions. The electrochemistry of cerium(III)- alkali metal heterobimetallic aryloxide complexes is reported and compared with cerium aryloxide complexes that are kinetically stabilized by hydrogen bonding cations that span between the complexed aryloxide ligands. Comparative electrochemical measurements reveal differences between the heterobimetallic complexes and the hydrogen-bonded complexes.INTRODUCTIONThe rare earth elements comprise the lanthanides, La–Lu, and the element yttrium (Aspinall, 2001). Rare earth ores such as monazite, LnPO4, and bastnäsite, LnFCO3, typically bear mixtures of light rare earths: La–Sm while monazite, LnPO4, contains mixtures of heavy rare earths (Eu–Lu) (Cotton, 2006). Pure rare earth elements typically are isolated using a liquid-liquid separations process.(Bautista, 1995) The hydrometallurgy of these elements is a difficult problem because the separation factors between neighboring rare earths, which are predicated on the small differences in the sizes of the trivalent ions, are quite small (Cox, 1992). The element cerium, with its 4f1 electronic configuration in the trivalent state, is unique among the rare earth elements due to a relatively accessible 4f0 electronic configuration. The accessibility of the 4f0 configuration underlies the chemistry of cerium(IV), the only rare earth ion with molecular chemistry in the tetravalent oxidation state (Cotton, 2006). Cerium is trivially separated from mixtures of light rare earths by making use of its unique oxidation chemistry. In an effort to extend separations chemistry by oxidation reactions to other rare earth elements such as terbium and praseodymium, the solution electrochemistry of well-defined cerium complexes is of interest."

Jan 1, 2012

By M. J. deBastiani

The uranium producing division of Denison Mines Limited operates a 6,000-ton-per-day integrated mining unit in the Algoma area of Ontario. The property is located approximately one and one-half miles from Highway I 08, eight miles north of the town of Elliot Lake. The property was staked in 1953, diamond-drilled in ?late 1954 and 1955, and put into production in 1957. Since that date, the operation has produced $250,000,000 worth of uranium oxide from approximately 11,000,000 tons of ore milled, and paid $18,000,000 in dividends to its shareholders. The operation employs about I000 people, and monthly operating costs are approximately one million dollars. From these figures alone, it is obvious that it was necessary to develop and institute an adequate set ?of controls for effective management at all levels of supervision over a period of four years, a system of production and cost control was developed that enables us to effectively measure the pulse of the various phases of the operation at any given time.

Jan 1, 1963

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006

By K. C. Marsden, B. Pesic

"Interest in the efficient production and recycling of rare earth elements has increased in recent years along with the prices of these elements. The molten LiCl-KCl eutectic is one ionic solvent which can be utilized for these purposes. The LiCl-KCl eutectic has also been selected as the electrolyte for focused research for advanced pyrochemical recycling processes for used nuclear fuel in several nations. Rare earth elements are fission products with notable neutron absorption characteristics, and thorough understanding of the properties and behavior of these elements is critical to their successful partition from the electrochemically-similar actinide elements. The number of research papers investigating individual rare earth elements has greatly expanded in the approximately 35 years since the last review. These research papers are presented in a variety of languages and technical formats, making data difficult to compare, and are sometimes contradictory. A review and summary of diffusion properties of rare earths in LiCl-KCl eutectic was performed, and the data translated to a common format for evaluation. INTRODUCTIONThe rare earth elements have experienced growing importance in recent decades due to their application in high technology, including optical lenses, lasers, high-temperature superconductors, improved alloys, high energy-density batteries, and powerful magnets for compact electronic devices. Their historic production methods and uses are detailed in several texts (Hampel 1971; Bautista &Jackson 1992; Gupta & Krishnamurthy 2005). A s the p rice o f these e lements has r isen in r ecent years, so has interest in their efficient production and possible recycling options. Rare earth oxides are concentrated through hydrometallurgical techniques, but the high thermochemical stability of their oxides precludes production of rare earth metals in aqueous systems. However, the wide electrochemical window and better control of pO2- in fused salt systems allows the production of these reactive metals from their halides or oxides. The high ionic conductivity and diffusivity of the molten ionic electrolyte allow high currents with limited resistive losses (Fray 1980). Electrolytic methods in fused salts are commonly adopted for the production of bulk rare earths in a variety of molten salt systems. Fluorides are sometimes proposed for oxide electrowinning processes due to ability to dissolve the rare earth oxide, reduced hygroscopic behavior, and the wider electrochemical separation between O2 and halide gas evolution (Mohan Das, Damodaran et al. 1988; Gibilaro, Pivato et al. 2011). However, in most electrolytic production processes, such as that for mischmetal, the rare earth oxides are converted to chloride prior to electrolysis in a chloride bath (Gschneidner Jr. & Eyring 1978; Sharma 1987). Of the chlorides, the LiCl-KCl eutectic is one specific medium in which metal production and production-related investigations have been conducted (Gschneidner J r. & Eyring 1978; Driscoll & Fray 1993). L iCl-KCl eutectic has the advantages o f h igh conductivity, but relatively low viscosity and operating temperature. The low operating temperature allows simpler design, with reduced energy consumption, salt volatility and cell corrosion."

Jan 1, 2012

By B. McHenry, A. E. Wraith, P. J. Mackey

The Wallaroo smelter on the Yorke Peninsula, South Australia commenced smelting operations in 1861 treating ores from the nearby Moonta and Kadina mines. The plant expanded and modernized on several occasions and was a leader in the successful introduction of new technology to improve operations. It operated continuously until 1923 when local mines became exhausted; in the closing stages of the 19th century it was the largest copper smelter in the world outside of those in Swansea, Wales. In 1892 a small electrolytic refinery was established at Wallaroo, the first in Australia, based on principles developed by Elkington at Pembrey, Wales in 1869. The Wallaroo refinery was specifically built to recover gold and silver from copper produced by smelting gold-containing feed materials shipped from Western Australia. This first venture into electrolytic refining was replaced in 1903 by a somewhat larger refinery which, although modest in size for its time, with a capacity of about 1000 tonnes of cathode copper per year, was very productive in precious metals. Anode copper was produced by an updated version of the reverberatory-based Welsh process until 1910 when barrel-type pneumatic converters were introduced based on American practice; subsequently, anodes were cast by tapping the precious-metals rich "bottoms" portion of converter copper as produced at about one-fifth into the copper blow. The present paper describes the Wallaroo refinery, its anode supply and products, supported by initial observations on a sample of a Wallaroo cathode held in the collection of the South Australia Museum, Adelaide SA, Australia. INTRODUCTION Australia ranked 6th in the world for copper mine production in 2018, with an output of 918,000 tonnes of mined copper, after Chile, Peru, Congo, China and the USA; about 40% of Australian mined copper was smelted in the country. Interestingly, the world ranking of Australia in mined copper has, with a few variations, remained about the same for more than 100 years – of interest, it was also the 6th largest country for copper production at 21,089 tonnes in 1899. At that time, all or most of the copper was smelted in the country (Mackey, 2016). Copper was first discovered in Australia in 1842 in South Australia not far from Adelaide; additional copper discoveries in the region soon followed. At first, copper ore was shipped to Swansea, Wales for smelting (Bampton, 2003). However, in addition to the long, 150 day one-way sea passage, it seems Welsh smelters preferred higher grade of ores – these aspects and likely a mood in the new colony to be independent of Swansea (Evans, 2014) evidently encouraged local smelting at the mine sites using small, Welsh-type reverberatory furnaces fired with hardwood as fuel and operated by Welsh and Cornish migrants. The first large copper smelter in Australia commenced in 1848 at Bremer, near Callington some 60 km east of Adelaide. With larger discoveries on Yorke Peninsula, the Wallaroo copper smelter at Wallaroo Bay on the west coast of the peninsula commenced operations in 1861 (Bell & McCarthy, 2008). Thus began one of the most successful, and in its day, one of the most advanced and innovative plants in Australia if not the world. In the late 1860s, it was considered one of the largest copper smelters in the world (Bell & McCarthy, 2008)

Jan 1, 2019

By H. Aaltonen, T. G. Robinson, M. Morimitsu

"The energy required to plate pure zinc can be the most significant operating cost for an operator in the production of electrolytic zinc. This paper reports on developments on low energy Outotec coated titanium anode process technology with fully amorphous coatings, MSA®, and its application to brownfield zinc electrowinning operations around the world. This technology aims to reduce the operating cost and increase productivity for zinc producers.INTRODUCTIONZinc electrowinning is an energy-intensive process using more than 3,000 kWh/t of electric energy [1-4], and the reduction of the energy consumption is one of the key issues. The high energy consumption is due to a high cell voltage during electrolysis, which is mainly caused by a high overpotential of oxygen evolution reaction on lead alloy anodes which have been widely used in commercial zinc electrowinning processes. The overpotential of oxygen evolution is 0.6 V or more and which is approximately 4 times higher on average than that of the cathodic reaction (zinc deposition) [3,4]. Therefore, the reduction of oxygen overpotential is significant to reduce the electric energy consumption, and this will become more significant with increasing demand in metal production and rising energy costs.Oxide coated titanium anodes have been widely investigated for the oxygen evolution anodes in order to replace the lead alloy anodes [5-9], because it is known that the oxygen overpotential strongly depends on the material and structure of the anode. The most typical example of such anodes is an IrO2-Ta2O5 coated titanium anode, which is usually prepared at thermal decomposition of a precursor solution containing metal salts at 450 oC or more and obtained mixed oxide coating consists of crystalline IrO2 and amorphous Ta2O5. On the other hand, one of the authors of this paper, Professor Morimitsu, Doshisha University in Japan, has developed a novel oxide coated titanium anode, MSA® [10-25]. The most specialized point of MSA® is that the catalytic coatings are prepared at low thermal decomposition temperature and amorphous IrO2 or RuO2 is contained as the components in the coatings. Such amorphous coatings have high catalytic activity for oxygen evolution compared to lead alloy or crystalline coatings. Outotec acquired the international specialized MSA® patent licensing rights from Doshisha University and has produced and commercialized the amorphous oxide coated titanium anodes. These anodes have already been utilized mainly in copper electrowinning plants worldwide and have demonstrated a significant voltage reduction, a cost-efficiency, and a long lifetime. This novel technology is also effective to zinc electrowinning process, thus this paper presents the characterization and performance of amorphous IrO2-Ta2O5 coated titanium anodes and amorphous RuO2-Ta2O5 coated titanium anodes for oxygen evolution in zinc electrowinning."

Jan 1, 2016

By K. S. Raja, B. McNall, B. Pesic

"High-level radioactive wastes are stored in large underground storage tanks made of low-carbon steel. The wastes consist of concentrated solutions of sodium nitrate (NaNO3) and sodium hydroxide (NaOH), and the radionuclides 137Cs, 99Tc, and 90Sr. The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV), which in turn modifies the kinetics of corrosion of the storage tank. To understand the influence of technetate ions on the corrosion of steel, electrochemical polarization studies of A 537 steel samples were carried out in 1 M NaNO3 + 0 .05 M S r(NO3)2 + 0.1 M NaOH with and without addition of HReO4 at different temperatures (24 – 85 °C). The concentration of HReO4 was varied from 0.014 – 0.04 M.INTRODUCTIONAqueous processing of spent nuclear materials generates a large amount of high-level radioactive wastes. The wastes are primarily salt solutions of sodium hydroxide and sodium nitrate which also contain fission products such as 137Cs, 99Tc, and 90Sr. Among the high level radioactive fission products, Tc-99 is of great importance because of its high concentration, long half-life (2.1 x 105 years), high solubility in geologic waters as technetate, and rapid diffusivity through the geologic systems. The solubility of technetate ions varies depending on the oxidizing conditions prevailing in the storage containers. High level radioactive wastes are stored in single shell or double shell tanks made of low carbon steels such as ASTM type A15, A516-70 and A537. Most of the available literature on corrosion of steel in simulated radio active waste environments pertains to nitrate induced stress corrosion cracking (Subramanian & Mickalonis, 2005). The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV). Corrosion of steel and formation of Fe(II) and Fe(III) will affect adsorption and reduction of Tc species. The radioactive species can irreversibly be sorbed on the steel surface by oxidation of Fe(II) to more stable Fe(III) and fixed as less soluble Tc(IV)/Fe(III). The solubility of Tc species is also affected by other factors such as dissolved oxygen, local pH, temperature etc. How the corrosion behavior of steel will be affected in the presence of Tc species is not clearly understood.Cartledge (Cartledge, 1960) demonstrated that passivation of iron can be achieved in the presence of oxygen along with suitable inhibitor ions/molecules of the general formula XO4 n-, such as pertechnetate (TcO4 -). The pertechnetate ion is univalent. Since it is derived from a strong acid, no buffering action can be expected from this ion. The redox potential of the reaction (1) is 0.738 VSHE (Pourbaix, 1974)."

Jan 1, 2012

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"The future of Polish copper mines KGHM Polish Miedz S.A. will be associated with mining at depth. At present, technologically advanced measures are being introduced to minimize the adverse influence of the environmental hazards on people working underground. Polkowice-Sieroszowice mine is the only mine in Poland where mining takes place in copper and salt deposits. On the basis of the current and anticipated methods of ventilation of a selected ore deposits the paper will analynze a number of solutions enabling planned mining of copper ore deposit, while minimizing the impact of natural aerological hazards in working areas. INTRODUCTION The future of copper ore mining, carried out by KGHM Polska Miedz S.A., will be based on mining from continuously greater depths (Butra, 2015). It is forecast that this will be accompanied by an increasing climatic hazard, resulting from an increase in the original temperature of rocks of more than 45°C as well as gas and geodynamic hazards (Soroko, 2015; Andrusikiewicz, 2015). Due to the safety of underground teams, a need arises to develop methods eliminating the adverse impact of the natural hazards, down to a level enabling the mining activity to be carried out on an industrial scale while maintaining favourable economic parameters. Current depths of the copper ore deposit being developed are effectively verifying the technical methods and measures employed to date for eliminating the natural aerological hazards. Amounts of air supplied to mining areas, with lengthy transport routes, are becoming insufficient for miners’ temperature safety, whereas increasing the power of cooling air-conditioning stations for cooling the air undermines the economic legitimacy. However, along with the temperature hazard, a significant problem at the current depths is an increase in gaseous occurrences in the headings’ areas. The concentrations of natural harmful gases found, even with the values below the permissible concentrations, in the case of limited amounts of air and/or low airflow rates, may pose a considerable danger to the workers. The hazards referred to are currently the major factors determining the advance of headings, above all in mining sections, being the outcome of geological structure and depth of lying of a deposit. However, at the current depths of mining minerals from deposits, room-and-pillar mining systems employed also have a decisive impact on the increase in natural aerological hazards."

Jan 1, 2019

By C. T. Harper, B. J. Fryer, R. P. Taylor

"IntroductionThe Maurice Bay deposit is one of a number of uranium deposits that have been found in recent years in the Athabasca Basin of northern Saskatchewan (Tremblay, 1982). This deposit, along with the others, belongs to the unconformity type deposits (Beck, 1977). They are, for the most part, polymetallic, being characterized by a suite of metals which include U, Ni, Co, Cu, Pb, Zn, Mn, V, Ag, Au, Pt-group elements, S, As, Bi, Se, Te, and Mo, some of which, besides U, are present in economic concentrations (Amok, 1974; Ruzicka, 1975; Tapaninen, 1976; Hoeve and Sibbald, 1978; Dahlkamp, 1978). The Maurice Bay deposit was known to be a small low grade deposit in which the ore was essentially monomineralic, consisting mainly of pitchblende (Harper, 1978). However, the occurrence of trace amounts of some of the elements common in the larger polymetallic ore bodies (e.g. Key Lake, Cluff Lake D) was anticipated. Thus a lithogeochemical sampling project was undertaken in 1979 across part of the Maurice Bay deposit (Harper, 1979). Major oxides (SiO2, Al2O3, FeO, Fe2O, MgO, CaO, K2O, Na2O, MnO, P2O5, and TiO2) and a group of the most common trace metals (U, Ni, Co, Cu, Pb, As, Au, V, and Se) were analyzed to determine whether any elemental patterns (halos or depletions) could be detected which would reduce the number of pathfinder elements needed for exploration purposes. In addition to the above metals, Th was also checked because some conglomerate strata in the Maurice Bay area are known to be thorium-enriched (Harper, 1978). Only the trace metal distributions will be discussed in detail in this report.General GeologyThe Maurice Bay area is underlain by three major groups of rocks, the White Lake metamorphic complex, an unnamed granodiorite complex, and the Athabasca Group, described previously (Fig. 1; Harper, 1979). Table 1 summarizes the stratigraphic features as deduced by geological mapping and the examination of drill cores."

Jan 1, 1986

By W. B. Agocs

"AbstractThe airborne magnetometer data of the Marmora iron ore deposit at Marmora, Ontario, have been used as an example to show the mapped results obtained by the use of line spacings of from 1 mile to 14 mile. The maps are illustrative of the results which could be obtained from such line spacings for any type of geophysical survey, and they show the probability of 'missing' a feature of economic value if the line spacing is too coarse.The probability equations are given for the crossing of randomly oriented features whose maximum dimension is less than the spacing of the control lines for circular, elongate, and rectangular outlines. The equations are P = D/S; P = 2L/S; P = 2(L+W)/,.S; P = A/,.S; P = (2L(S+T)-L2),.ST; and P (D(S+T-,.D)) ST, respectively; where P is the probability; D is the diameter; L is the length; W is the width; and S and T are line spacings.IntroductionTHE EFFECT of station spacing, and the effect of the distance between the plane of observation and the plane of the source of the potential field anomalies, have been studied by geophysicists in the past.The purpose of this paper, however, is to illustrate the effect of line spacing •on the resultant mapped magnetic anomaly for a known magnetite mass, and to present the elementary probability equations for determining the optimum control spacing for detecting a particular type of feature. The effect of line spacing which is illustrated by the magnetic maps presented herewith would be comparable to results which would be obtained by any geophysical survey, since the contours between lines are of necessity interpolated."

Jan 1, 1955

By H. Lorenzen, D. Buyze

"Magnesium-bearing salts occur in the Zechstein Basin in the north eastern part of the Netherlands at a depth of 1500m to 2500 m.Exploration results justified the exploitation of these salts by means of solution mining for the production of refractory grade magnesium- oxide. This paper discusses design criteria, operation parameters, and methods used for magnesium chloride solution mining by Noordelijke Zoutwinning B. V. (NOZO), an operating company of Billiton International Metals B. V.A unique variation of widely used solution mining techniques has been developed for mining the complex Veendam salt deposit. NOZO extracts salt through deviated wells with a set of parallel, suspended tubings. Cavern fluid pressure is maintained close to that of overburden rock. These special design features provide an answer for the complex characteristics of the minerals, halite, carnallite, bischofite and kieserite, from which a solution rich in magnesium is generated. Dissolution chemistry and rock mechanical behaviour of these salts are unlike those of rock salt. Throughout a few years, NOZO demonstrated adequate process control while they continue improving the operation.IntroductionBilliton, a wholly owned company of the Royal Dutch /Shell Group of Companies, is active in metal exploration, mining, processing, and trading, mainly in the non-ferrous sector.Since 1972 Billiton has been active with solution mining magnesium salts in the northeastern part of the Netherlands, in the Province of Groningen, near the city of Veendam . Solution mining techniques were developed in conjunction with the ""Koninklijke/Shell Laboratorium Amsterdam"" (KSLA) and the ""Koninklijke/Shell Exploration and Production Laboratorium"" (KSEPL), Rijswijk. The company's objective is to produce magnesia sinter (MgO) from magnesium-chloride brine (MgClz) and de-carbonated dolomite (CaO.MgO). The magnesia produced serves as base material for the manufacturing of refractory bricks, used for furnace linings in the steel industry."

Jan 1, 1986