Search Documents

By R. Cottam

The deformation and recrystallisation of magnesium yttrium alloys containing 0.23, 0.84 and 2.71wt% yttrium and commercially pure magnesium extrusion has been investigated at temperatures between 200 and 350°C. The alloys were produced as billets 7.5 cm diameter, solution treated at 525 °C for 8 h and extruded into 3 cm diameter bar at 390°C. Channel die compression was employed to deform the samples at a strain rate of 1x10-3s-1. For the 0.23 wt% yttrium alloy and the pure magnesium, dynamic recrystallization (DRX) occurred at all temperatures and the amount of DRX increased as the temperature was raised. In the alloys containing 0.84 and 2.71 wt% yttrium DRX was almost completely suppressed at all temperatures. The absence of DRX in the 0.84 and 2.71 wt% yttrium alloys was accompanied by a decrease in the ductility, except at 350°C the highest deformation temperature. It was observed that this increase in ductility was accompanied by a reduction in deformation twinning and the initiation of pyramidal slip. This work highlights the important role that DRX plays in enhancing the ductility of magnesium alloys.

Jan 1, 2006

By A. R. Byers

"This paper describes the distribution, occurrence, and paragenesis of known sulphide deposits within an area bounded by longitudes 102°00' to 106°00' west and latitudes 54 ° 301 to 57 °00 1 north. The Precambrian bed-rock which outcrops over all but the southern fringe of the area con- . sists of regional metamorphic assemblages ranging from low grade or green schist facies to high grade or amphibolite-granulite facies. The areas . of low-grade metamorphism correspond to 'islands' of volcanic rocks which are surrounded by highgrade paragneisses and migmatites. Intrusive rocks range in composition from ultrabasic to granitic and may be divided into syntectonic and posttectonic sequences. The average composition of the former is granodiorite and of the latter quartz diorite.The massive sulphide deposits fall naturally on basis of mineral content into the following divisions: ( 1) pyrrhotite and / or pyrite, (2) sphalerite and/ or chalcopyrite plus iron sulphides, (3) sphalerite and galena, ( 4) sulphide-bearing pegmatite, and (5) nickeliferous pyrrhotite and / or chalcopyrite. The deposits of iron sulphides are ubiquitous. Ratio of pyrrhotite to pyrite is fairly constant for individual deposits, but their areal distribution appears to be independent of the nature of the enclosing rock and grade of regional metamorphism. All deposits containing ore-grade quantities of base metals have been concentrated at favourable structural locations. Copper-zinc and lead-zinc deposits appear to be associated with syntectonic granodiorite with the lead-zinc concentrations confined to calc-silicate gneisses. Copper-nickel deposits show a close relationship to post-tectonic gabbros and pyroxenites. The paragenesis is more or less the same for the majority of deposits, with iron sulphides and sphalerite being introduced early and followed by chalcopyrite and galena. Some vertical and / or horizontal zoning is apparent in a few deposits. Temperatures of formation and origin of the deposits are briefly discussed."

Jan 1, 1960

By W. S. Dyer

The lignite deposit at Onakawana on the Abitibi river is of particular interest at the present time, since the Ontario Government has recently decided to proceed with the extension of the Temiskaming and Northern Ontario railway to James bay. Forty-five miles of steel will be laid this year to the crossing of the Moose river. This will cross the lignite field. It has been known for many years that lignite occurred in the Moose River basin, but it was not until drilling was commenced at Blacksmith rapids (or Onakawana, as the camp is now known) in June, 1929, that a seam of economic thickness and extent was found. Early in 1929 the Ontario Legislature voted $25,000 for the carrying out of a drilling programme in the Moose River basin. This came as a culmination of two summers' exploratory work by the Geological Branch of the Ontario Department of Mines, and as the result of a report which said; in effect, that further information concerning the mineral resources of the basin could only be obtained by drilling, and that such a drilling programme was well worth while in order to establish once for all whether lignite, fire-clay, or oil or gas did or did not exist in economic quantities in the region.

Jan 1, 1930

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By J. Buckle

"Recognition of the diamond potential of the Wawa subprovince was initially determined from regional data using a kimberlite model. The world’s largest stable Precambrian craton, the Superior Province, is considered to be favourable for the emplacement of diamondiferous kimberlite. The Wawa area is located near the intersection of intra-craton structures visible in the regional magnetic data.The Enigma project is located north of the town of Wawa in northern Ontario. From field evidence and background research, it became obvious that in the Wawa area there were at least two potentially diamond-hosting events, Archean lamprophyric volcaniclastics and Proterozoic kimberlites. The host lamprophyric rock does not contain the classical KIM signatures. However, to complicate the Enigma, stream sediment samples within 200 m of the diamond-bearing lamprophyre produced a typical suite of kimberlite indicator minerals.The micro- and macro-diamond content of the Wawa lamprophyric volcaniclastic rocks is typically 0.2 ct/t to 1 ct/t, although it can be higher locally. The economic diamond potential of these Archean dykes, sills and irregular lamprophyre bodies is still under-explored (Kaminsky, 2002, unpubl.). Oasis Diamond Exploration is currently exploring the area using geophysical, geochemical, and geological data."

Jan 1, 2002

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By Knut F. Garshol

Quality and durability of sprayed concrete depends on the concrete mix design, the type and use of accelerator and all the aspects of the placement onto the rock surface in the underground working. A large number of influence factors are involved and they must be managed for a successful and durable permanent sprayed concrete structure to be produced. The paper discusses some of the central issues, including how to view the long-term effects of chemical admixtures and accelerators in wetmix sprayed concrete. Permanent lining sprayed concrete for rock support is increasingly being used today and the durability can be equally achieved as for any other concrete.

May 1, 2003

By X. M. Zhou, T. Wu, He X. N.

"In order to study the support effect of concrete in the surrounding rock of a metal mine, the concrete and surrounding rock were comparatively studied. Firstly, the general situation of the ultra-kilometer deep shaft in Xincheng, surrounding rock and geological conditions are introduced. Secondly, the experimental scheme of material mechanical properties of surrounding rock and shaft lining concrete based on same standard dimension and shape are examined, and the mechanical tests of rock and concrete based on different shapes and sizes are carried out. The study shows that the compressive strength value and elastic modulus of the rock cube are 1.28 times and 1.78 times that of the cylinder, and the Poisson's ratio is 0.77 times. The dimensional effect law of the concrete cube and cylinder test data is consistent with the rock law. However, the test results of the concrete are less discrete than the rock; the test also shows that the strength and elastic modulus of the concrete lining of the main shaft of the Xincheng are much smaller than the surrounding rock that is also used as the concrete aggregate, which indicates that the support of concrete lining in the surrounding rock shaft behaved weakly. Based on the development of the modern NATM rock support theory, it is suggested that the mechanical test standard of artificial support materials should be unified into the mechanics test standard of natural rock, which will help to improve the accuracy and practicality of scientific calculation of geotechnical engineering.INTRODUCTIONConcrete and rock mass are usually attributed to a class of materials called frictional materials or geotechnical materials, of these two kinds of materials, the first is man-maded and the second is natural. The attentive scholar can find that there are many differences in the test criteria for the mechanical properties of the two kinds of materials among different industries or departments, reflecting the differences in their sources, tradition, and the application thoery of material strength among them.There is a situation wordwide, that there are many testing standards of the same material mechanical parameters such as elastic modulus, compressive strength, etc. The cube with a side length of 150 mm is adopted as a common sample in the architecture department in China, while a cylinder with a diameter of 50 mm and a height of 100 mm is as a standard specimen in geotechnical department.Knowing that mechanical parameter values are strongly affected by the the size, shape of specimen and loading rate etc, that is to say the mechanical parameter values of the same material are completely different when obtained from different test with different standards. However, such a problem has been long neglected in geotechnical engineering."

Jan 1, 2019

By J. C. Kingston

Introduction The sliding-form method of erecting concrete structures was first devised and used in the early part of this century by the Sante Fe Railroad Company for the erection of a grain elevator at Santa Fe, New Mexico. A somewhat related principle has been employed for a number of years in shaft lining work and, to our knowledge, was perfected in Butte, Montana, but until the building of the concrete headframe at the Jeffrey mine of the Canadian Johns-Manville Company, Ltd., at Asbestos, Que., the method, as applied to surface structures, was quite foreign to the mining industry in Canada. The current shortage and cost of structural steel shapes has no doubt contributed more than any other single factor to the investigations that have led to the use of reinforced concrete as a headframe building material. Mining men in western Quebec and northern Ontario have shown a great deal of interest in the design and construction of the headframe at the East Sullivan mine in Bourlamaque township, Que., and we have had many queries regarding the methods used and, in particular, for an explanation of the sliding-form principle. This article is written in an attempt to set forth the conditions which were to be met; to explain the construction methods used, and to discuss the economy of concrete headframes as compared with the conventional steel structures with which the mining fraternity is familiar.

Jan 1, 1949

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By Edith Lafontaine

Modern underground mines operate fleets of mobile production equipment including drill jumbos, long-hole drills, load-haul-dump machines, trucks and bolters. Their availability has a substantial impact onto production cost and thus onto mine profitability. Through appropriate collection of pertinent data and information, use of adequate performance measures and their analyses, mine operators can identify the most promising and cost effective opportunities to get more from their equipment and to reduce the overall cost. This paper presents results of the study aimed to review and analyse means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews current reporting procedures, sources, quality and quantity of the data and information collected as well as examines performance measures and their definitions used by the surveyed mines. Problems concerning data acquisition as well as meaningfulness and usefulness of the above mentioned metrics are also discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. It is believed that the latter may become a more useful tool for mine operators in their efforts to reduce production cost than it seems to be the case at present.

May 1, 2007

By Richard C. Banting

Excessive vibration is known to have an adverse affect on soft body tissue and operators of heavy mining equipment can be exposed to vibration that exceeds levels recommended in international guidelines (ISO 2631-1, for example). Research has found that many of the seat and suspension systems currently used in mine haul trucks and load haul dump vehicles are actually amplifying the vibration. This overview presentation will outline the current research being conducted at Laurentian University and the University of Western Ontario, and the roles of partners in rating the ability of a number of commonly used mine vehicle seats to isolate harmful vibration.

Oct 1, 2010

By Graham A. Karklin

"The Echo Bay Mines silver property is located 875 air miles north of Edmonton, Alberta. The mine is on the east shore of Great Bear Lake at Port Radium which is twenty six miles south of the artic circle, in the North West Territories.HISTORYThe area was first surveyed by J. Mackintosh Bell of the Geological Survey of Canada in the early nineteen hundreds. In May 1930, Gilbert LaBine staked claims at Port Radium called ""Cobalt"" and ""Cobalt I"". What he had discovered was an extremely rich vein of pitch-blend. These claims were the birth of mining in this area. The first ore shipment of pitch-blend was hand-picked and flown out of Port Radium in 1931. LaBine's discovery of pitch-blend became of world-wide importance with the outbreak of World War II. In 1939 the splitting of the uranium atom brought this area into world focus. It is generally believed that it was ore from this area that was used in the production of the devastating bombs which were dropped on Japan.It was at Port Radium that the leaching process for uranium extraction was pioneered. The resultant methods have been modified and adopted for use around the world. The mine was originally owned by Eldorado Gold Mines Limited. Echo Bay Mines leased the property in 1964, subsequently purchased it, and have been producing silver and copper every since."

Jan 1, 1981

By Peter N. Calder, Garston Blackwell

"The history and analysis of a structurally complex open-pit rock slope displacement are described. The failure involved part of the only haulage access to a major ore zone. The ongoing movement was monitored using an electronic distance measuring device and a continuous electronic system specifically designed for the problem. A major fault, infilled with a thick clay gouge, and intersected by other structural features, resulted in the transfer of weight to a rock mass acting as a buttress in the lower regions. Movements were affected by blasting vibrations and ground-water conditions. Remedial measures included limiting blasting levels and lowering the water table, following which mining was successfully resumed in the area.IntroductionBrenda Mines is situated in a mountainous region of the southern interior of British Columbia; the location is indicated on Figure 1 . The elevation is approximately 5000 ft , giving a climate typical of more northern areas. Temperatures vary from -30°C to + 30°C. A snowfall level of 400-800 cm is experienced from November to April. During the spring, a heavy runoff period occurs, increasing the pumping rate in the pit from a nominal 50* gal/min to 2000 gal/min.The orebody occurs in a fractured Jurassic rock mass referred to as the Brenda Stock; it is approximately 3000 ft in diameter and 1000 ft deep. The Brenda Stock was intruded into the Upper Triassic Nicola Group tuffs, breccias and argillites. Mineralization occurred in several stages in a relatively homogeneous quartz diorite host rock. Shearing, faulting and jointing occured later in many stages, producing mineralized clay gouge zones up to several feet in thickness'> , These gouge zones have a major effect on the stability of the pit walls.The structural geology of the pit walls is otherwise relatively simple. Figure 2 is a conventional pole diagram indicating the orientation of the rock structural systems which are present. The major system has an average dip of approximately 70 degrees to the south and strikes approximately east /west , it is not undercu t by the pit slope. Figure 3 is a photograph of part of the North wall on which this system is indicated.The basic pit design consists of a working bench height of 50 ft, with a final wall height of 100 ft between berm s and a 100-ft-wide berm every second lift. Combined with a local face slope of 50-70 degrees, the resulting wall slope, not including haulage roads, is 45 degrees. Figures 4 and 5 are generalized plans and sectional views of the pit."

Jan 1, 1980

By A. P. Bois, K. Saleh, A. Ghorbal, V. Hajiabdolmajid, G. Ballivy

"The knowledge of the initial stress field is not always sufficient to ensure the stability of mining stopes due to the high-stress variations generated by mining. Monitoring of these openings is then necessary and can provide quantitative information (deformations and stress variations) as well as qualitative information (state of stability).An applied technique for following the variations of stress and deformation in static and dynamic conditions, in relation to the evaluation of the stability of underground openings known as “Cylindre Instrumenté de l’Université de Sherbrooke” (CIUS) is discussed in this paper. In addition, a data acquisition system combined with a rock failure warning system has been developed to be connected to the CIUS for detecting the instabilities, which can endanger the stability of underground openings. Also, the installation of six CIUS and a data acquisition system as well as the selected procedure of programming in a warning system are briefly described."

Jan 1, 2003

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

By N. Bédard

"This paper highlights Cambior’s initial approach for recruiting and retaining its international employees, the importance of proper preparation and the support needed to ensure a competent and stable workforce.In general, most of the training and information available for human resources personnel prepares the specialist for handling various aspects of labour relations, recruitment and hiring, benefits administration, employee relocation, etc. This is usually done in a Canadian context.Only recently, has more specialized training been developed to prepare human resources practitioners for the complex issues related to expatriate employees and dealing with human resources issues in other countries"

Jan 1, 2004

By J. C. Bothan

A program to provide technical in-formation on the use of fuels in pyro-metallurgical processes, from the Canadian fuel viewpoint, was initiated about five years ago by a Canadian Institute of Mining and Metallurgy liaison grou1> composed of members from the Coal Research Committee of the Coal Division and the Iron and Steel Committee of the Metallurgy Division. This paper is another of a series prepared for this program. Previous papers included a review of pyrometallurgical processes of Canadian interest, a survey of ferrous processes relevant to the development of an integrated steel industry in western Canada and a survey of the fuel requirements of the non-ferrous metals industry in Canada. It is widely recognized among per-sons familiar with the Canadian coal industry that, because of the large resources of coking coal in western Canada, the

Jan 1, 1963

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By The Staff

Introduction For many years the necessity of mechanization of all the underground services in the collieries of the Dominion Steel and Coal Corporation in the Sydney, Pictou, and Cumberland coalfields has been foremost in the minds of those concerned with the engineering and operating policies of the Corporation, and a gradual policy of the mechanization of these services has been undertaken over the years, until nearly all the underground services, except the actual loading of the coal at the face, have been mechanized. Early in 1928, experiments in mechanical loading were conducted which finally culminated in the installation of mechanical loading units in our No. 20 colliery in 1938. This attempt at mechanization of the final underground services proved unsuccessful because the workmen were not ready to accept complete mechanization, and the fruition of many years of study was delayed until the year 1947. During the ensuing years, the engineers and operators of the Corporation had studied the possibility of adapting to conditions prevailing in Nova Scotia mines the many types of loading equipment in use in the United States and Europe. The varied physical conditions which exist in the fields operated by the Corporation rendered it extremely difficult to apply the equipment and technique successfully employed in the United States, and more recently in Europe, and special techniques have had to be devised to meet the need of each individual colliery. Prevailing physical conditions in the Nova Scotia fields find no parallel for mechanization with those of any other part of the American continent.

Jan 1, 1949