Search Documents

The mIning operations of Bougainville Copper Pty. Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea.C.R.A. Exploration Pty. Limited first established mineralization in the Panguna area in 1964. Exploration work since then has established ore reserves estimated to be 900,000,000 long tons of ore assaying 0·48 per cent copper and 0·36 dwt/ton gold. An economic feasibility study completed in July, 1969 enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons/day. The concentrate will be pnmped as a slurry through a 16 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 MW steam power station, and access roads.

Jan 1, 1971

By Snowdowne J. B H

Rand Mines, Limited, located in Johannesburg, Republic of South Africa has recently completed feasibility studies which have lead to the initiation of two major coal strip mining ventures. A minicomputer based mine planning system was developed to perform the feasibility studies. The broad approach of this system is to utilise inter.-actively the specialist skills and interpretative abilities of mining engineers and geologists. This paper reports briefly on the outline of the system and at greater length upon certain aspects of its use.

Jan 1, 1977

By Avraamides J, Ritchie I. M

Gold Tellurides are important sources of gold at Kalgoorlie, Western Australia, Cripple Creek, Colorado and Vatukoula, Fiji. Unlike free gold, the tellurides of gold are rather refractory and the usual treatment practice has been to oxidize the tellurides, either chemically or by roasting prior to cyanidation of the liberated free gold. There is a large measure of disagree- ment as to the actual cause of the refractory nature of gold tellurides. In order to investigate the leaching chemistry of gold telluride, a study was undertaken on the thermodynamics and kinetics of its dissolution using electrochemical methods. From this study suitable direct leaching condi- tions are suggested. In acidic chloride solutions gold telluride can be leached using iron(III) as the oxidant. At lower acid concentrations the reaction is controlled by the formation of a passivating film of H2TeO3. In alkaline solutions containing cyanide the rate of gold telluride dissolution increases with increasing pH and strength of oxidant. However, this can result in excessive consumption of cyanide in the presence of stronger oxidants.

Jan 1, 1991

An understanding of the importance of the different components that comprise a rock bolt unit is necessary to ensure the proper use of rock bolts as a means of roof support. The various anchors, bolts and plates in use in Australia have been designed and adapted for Australian con- ditions. As mining conditions change, so will the types of bolts in use. This is apparent in the development of chemical anchors and other recent innovations.

Jan 1, 1971

By Churchill M

One of the significant changes which has occurred in the flotation sector of the minerals industry, over the last two decades, has been the successful development of the very large flotation machine. The last twenty years has seen the volume of the individual cell, available to the industry, increase by a factor of ten. Today, new mills, and existing mill modernization plans, can consider individual cell volumes as large as 85 m3 with the certainty that the metallurgical performance capability of the large machine is inherently as efficient as the smaller machine. The large flotation cell offers benefits to the user such as reduced floor space, lower total power, process control simplification, and reduced maintenance. However, the flotation machine size selection process, based on overall installation economics, must include such factors as process tonnage, flotation kinetics characteristics, and metallurgical performance objectives. This paper discusses the flotation machine size and circuit arrangement selection based on both metallurgical performance and economic considerations. A computer based flotation kinetic analysis technique, which has proven valuable in quantifying the metallurgical response of flotation circuits having different cell sizes and number, is utilized to illustrate the selection of cell size and arrangement best suited to a client's Requirement.

Jan 1, 1991

During the past five years there has been a transformation in the operating costs which apply to narrow vein mining. Mechanised methods including sublevel uphole retreat and narrow vein cut and fill are now proven. Other methods, such as vein mining by horizontal drilling from a raise platform are currently being tried in Australia.The important factors which affect the cost and appropriateness of each method include: ore continuity, the planarity of the wall contacts, relative hardness of ore and wall rocks and the dip bf the deposit.Drawing on current operating costs from a number of mines and on recent feasibility studies, a methodology for estimating the costs of narrow vein mining is presented. These costs are then placed in their economic context with regard to ore grade and mining rate.

Jan 1, 1993

By D Lau

Traditionally X-ray diffraction (XRD) has not been significantly used by the cultural heritage sector, as the most commonly used technique, X-ray powder diffraction (XRPD), requires sample removal from the artwork or artefact, followed by grinding of the sample to a fine powder. With the development of micro-X-ray diffraction (micro-XRD) and other associated advances, non-destructive, in situ analysis of crystalline pigments on micro-areas of paintings and artefacts has become possible. This is illustrated with the application of this technique to the in situ analysis of propriety paints, paint cross-sections and small paintings. However, workers have noted that XRD can be insufficiently sensitive with pigment mixtures, due to matrix effects. This study obtained X-ray diffractograms of 17 single pigment preparations and determined relative amounts of crystalline content. The purity of single pigments was compared with Joint Committee on Powder Diffraction Standards (JCPDS) database diffractograms. The impact of pigments with high X-ray absorption coefficients on the detection limits of pigments with low X-ray absorption coefficients was further investigated by building on work done with the chromium oxide-zinc oxide series with the preparation of a second series of binary mixtures of zinc oxide (which has a high absorption coefficient and is almost fully crystalline) and ultramarine blue, which has a lower absorption coefficient but which is more crystalline. Semi-quantitative analysis, where baseline and absorption factor corrections are made, confirm detection limits as low as five per cent for chromium oxide and ultramarine blue when in a binary matrix with zinc oxide. However, this type of analysis is very time consuming. So in order to theoretically simulate issues that will be encountered with binary pigment mixtures, the single phase diffractograms were used to theoretically investigate the matrix effects of the three white pigments with the various coloured pigments. This illustrated that detection limits can be as low as five per cent or in non-ideal conditions, such as with partial peak clashes or where there are large differences in relative peak intensity, as high as 50 per cent. These results have significant implications for the analysis of painted surfaces on artworks or artefacts. It has been demonstrated that ideally this method is more suited to the investigation of surfaces where there is minimal mixing of pigments or where there is not a significant difference between the absorption coefficients of the mixed pigments.

Jan 1, 2008

By Lo YC, Pate WT

In recent years there has been a great deal of interest in ways to optimise the performance of mineral processing plants. This paper describes a methodology developed for optimisation of autogenous and semiautogenous mills. The methodology involves plant sampling, batch testing, modelling, computer simulation, control strategy evaluation and implementation. The models have been tested in plant operations to verify the research findings and predictions. Two example applications of this approach to plant optimisation are presented. Benefits reported in these two examples are in the range of four - eight per cent increase in size reduction efficiency.

Jan 1, 1993

By Zingano A, Costa J. F

Brazilian amethyst production is mostly obtained from underground mines in the southernmost part of the country, involving approximately 6000 miners and generating an income of US$ 20 million per year. Amethyst-bearing geodes are hosted by Cretaceous continental flood basalts of the Serra Geral Formation. The economic zone occurs in the massive (colonnade) intermediary section of the Sao Gabriel Basalto. The tunnels and stopes follow the occurrence of geodes leading to an erratic and complex layout. A ground control survey revealed excessive roof convergence. Topographic results show excessive roof deformation and some roof falls have already been reported. To understand the ground conditions, prevent roof falls and better define the pillar dimensions detailed geomechanical mapping was carried out using the scanline method. Uniaxial compressive strength tests provided complementary information for rock mass classification. Results of the geomechanical classification were used to modify the mining layout taking into account the roof and pillar geomechanical characteristics. Retreat pillar mining minimised ground instability.

Jan 1, 1997

By Vidalinc, Raffoux

Longwall faces producing in the order of 20,000 tons per day of raw coal are presently running in the Houilleres du Bassin de Lorraine of Charbonnages de France. Production levels of twice that level pose some technical and economic problems of coal cutting, ventilation, coal and equipment transportation in the.face and from the face to the sur- face. The peak productions of the equipment in use today, the results of trials with new equipment, the utili- sation of forecasting models (some in the form of software), allow us to fo- resee feasable technical solutions to these problems. They will first be considered in the best possible context (thick- ness, dip, non gassy, soft coal, good strata, no faults). This will give. the necessary conditions to reach daily output'of that level. A sensitivity analysis of these- figures to the effective natural con- ditions will then be undertaken and the implication of such a project on health and safety (dust, climate ...) will be carefully considered. A concise technical and econo- mical approach will permit us to fore- cast the economical interferences of such production units and specially the consequences of sudden variations of the output (downtimes, failures, etc). From this investigation, goals for technological development and re- search areas will be outlined to be able to reach this production target in the XXIst century.

Jan 1, 1988

By Paton T. P

In the technical sense, as well as in the professional sense, the word 'model' can have many meanings. More than 23 000 references were uncovered by a simple literature search on keywords ' MO D EL#. and. (META LLURG#. or. M I NERAL#)' . For the purpose of this paper, 'models' will be considered to be mathematical formulations which attempt to represent or approximate a process. The model may be purely, or a combination of: ò fundamental models, based on the laws of physics, chemistry and thermodynamics; ò semi-empirical or phenomenological models, where an intuitive concept of the process is formulated and found by testwork to fit observed behaviour; and ò empirical or 'black-box' models (including neural networks), where a mathematically convenient form is proposed and fitted. Even under this more restricted definition, which eliminates heuristic and statistical 'models', it is clear that the efforts expended in devising and using models have exploded during the years since the first APCOM Conference in 1961, benefiting from the dramatic decrease in the cost of computer power. This paper reviews the areas of usage of computer modelling in the metallurgical and mineral processing industries, from plant design, through off-line support, to on-line modelling and automatic control. In each area, frontiers of new development of the technology are mentioned. It is noted that, while modelling is now standard practice in design, it is not yet the norm in operating and controlling plants. The reasons for this partial acceptance are, it is argued, less related to the limitations of the technology than to the human and organisational factors involved in transferring technology to implementation.

Jan 1, 1995

The operators of the iron ore railroads in the Pilbara faced problems of excessive wear between rail and wheels as the tonnage hauled increased in the early 1970's. Joint research projects were begun between Hamersley Iron, Mt Newman Mining and the BHP Melbourne Research Laboratories to study these problems and recommend solutions. The particular problems of wheel rail interaction were solved by asymmetrical profile grinding of the rail and modifications to the machining of the wheels. Rail materials were improved through increasing yield strengths by alloying and by heat treatment. Wheel materials were improved by alloying. The economic benefits of these improvements have been demonstrated by much reduced re-rail requirements and other reduced maintenance costs.

Jan 1, 1986

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By Peirong C, Pei N, Shouxi H, Hongzhong X

Indosinian (T) orogeny amalgamated the Mongolia-Xingan fold zone, the North China continent, the Yangtzi platform and the SE China fold zone into a unified continent. The early to middle Yanshanian (J-K,) orogeny created a Cordilleran type active continental margin in East Asia, reactivated the consolidated East China continent, and generated a large amount of granitoids, calc-alkaline volcanics and W, Sn, Mo, Cu, Au, and U ore deposits. The late Yanshanian (K2) orogeny began a transition to the western Pacific type continental margin. A tensional environment led to the development of peralkaline magmatism and the formation of continental basins with red beds. The Himalayan (Tr-Q) orogeny was characterised by a backarc spreading and rifting regime. The dominant magmatism was continental basaltic.

Jan 1, 1995

By R Austerberry, S Green

Highly weathered ground, limited collar options and the need to achieve a desired outcome at the lowest possible cost led to the need to adopt a construction approach that had no established design methodology. The newest ventilation shaft at Mandalay Resources’ Costerfield Operations had to be established to a depth of 30 m through poor ground best described as ‘sticky swelling clay’, some of which was contained within an old backfilled pit.The ability to excavate a traditional presink was not possible due to limited space and the introduction of men into the shaft was to be avoided due to the associated safety risks and corresponding increase in cost. Piling in conjunction with raise boring and remote fibrecrete application was identified as a possible solution that could achieve the desired outcome at an acceptable level of risk.Construction of the piles was challenging and required continual refinement until an acceptable level of productivity could be achieved. Limitations on concrete delivery was taken into consideration to ensure hole stand-up time was acceptable and re-drills were not required. The adoption of a set process from alignment, drilling, concrete placement and testing ensured the desired design was achieved. Mine operators should consider the use of piling as a method of shaft stabilisation for the portion of raise bored shaft that passes through the weathered zone.The importance of quality control and attention to detail through the entire shaft construction process cannot be underestimated as issues such as insufficient geotechnical investigation, pile and pilot hole deviation, concrete and fibrecrete quality, as well as delays in the application of fibrecrete can place the success of the project at risk.This paper outlines key learnings from a client’s perspective with regards to the concept, planning, design, execution and completion of a 3.1 m diameter raise bore shaft through both weathered and highly structured ground at the Augusta Mine.CITATION:Green, S and Austerberry, R, 2014. Piling and raise bore construction – key learnings from a client’s perspective, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Warren L. J

In the mineral processing industry solid-liquid separation within a thickener usually requires the addition of a synthetic flocculant to enhance the settling rate of fine particles. The characteristics of the resulting flocculated suspensions may vary considerably depending upon the physical and chemical conditions which prevail during the flocculation process. For example, parameters such as flocculant type, dosage and solution concentration, surface chemical characteristics of particles and the suspension agitation conditions can influence the degree to which the particles aggregate. Aggregated suspensions exhibit various structures, and range from those composed of small, dense aggregates to those containing large, voluminous aggregates. The size distribution and structural type of the aggregates which form within the feed-well of a thickener can have a dramatic effect upon overall thickener performance. Thickener performance cannot be optimized without optimization of the aggregate structure produced in the feed by synthetic flocculant addition. This has required the development of new techniques to quantify the nature of aggregated suspensions, details of which are presented in this paper.

Jan 1, 1989

By G W. Wilson

Rehabilitation of tailings impoundments is one of the most challenging aspects in mine closure, as not only does the potential for producing leachate pose a challenge to the rehabilitation designer, but also other aspects such as stability and settlement must be considered. The water balance of a tailings impoundment is unique in the sense that it usually hosts a pond that in turn causes a phreatic surface in the impoundment. The position of the phreatic surface defines the saturated and unsaturated zones in the impoundment, which of course varies spatially and temporally. Predictive modelling for this hydrologic system becomes difficult, as numerical models capable of analysing the combined saturated/unsaturated zones are not adequately refined to accurately solve the flux boundary problem for infiltration at the surface of the tailings. This paper describes the development of a flux boundary model that enabled accurate modelling of the unsaturated zone in the tailings impoundment at Kidston Gold Mine, Queensland, Australia. The technique made it possible to accurately predict the spatial variation of infiltration to the tailings as a result of the presence of the phreatic table. The conceptual model defines the boundaries for the Kidston tailings dam, based on a generalised cross-section through the dam. Firstly the shape of the top boundary is described as a function of the particle size of the tailings associated with particle segregation that occurs due to the hydraulic placement of tailings. This function was rigorously tested using in situ infiltration tests and laboratory materials testing. Defining the bottom boundary of the section, ie the phreatic level was done by physically monitoring the phreatic level with 42 piezometers strategically located on the tailings dam. Analysis of this data led to the fixing of this bottom boundary through the introduction of a function that mimicked the shape of the phreatic level. The material properties of the surface layer, specifically the saturated permeability that would govern the infiltration/exfiltration rates of moisture through the top boundary layer were defined on the basis of extensive field and laboratory material testing. A function for the saturated permeability was developed on the principles of particle segregation. Finally a procedure is described for the application of the new conceptual model for the evaluation of the spatial infiltration to a tailings surface using the rigorous one dimensional surface flux boundary code SoilCover. The solution of the calculation described above was then used as the top boundary condition in conventional three dimensional saturated/ unsaturated flow codes, and verified against measured seepage rates from the tailings impoundment under drains. It was concluded that the developed spatial flux function was in deed a most rigorous representation of reality. Although the methodology presented here was applied to the Kidston tailings impoundment only, the authors believe that the principles are directly transferable to any tailings impoundment that has a varying phreatic zone thickness due to the presence of a pond. The mathematical equations describing the typical cross-section would be site specific, but the approach and ultimate solution methodology would be directly transferable.

Jan 1, 2003

By Haeussler P, Christie A, Bradley D, Skinner D

Mesothermal gold deposits of southern Alaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat was produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

By Corbett GJ

Comparisons between individual SW Pacific Rim gold deposits have facilit-ated proposal of a new classification of porphyry-related mesothermal gold deposit types. Carbonate base-metal gold systems form at relatively high crustal levels, peripheral to porphyry intrusions. There is a spatial assoc-iation with major structures which focus fluids from degassing porphyries at depth. Milled matrix intrusive breccias and extrusive maar volcano/ diatreme breccias form as a result of pre-mineralisation phreatomagmatic eruptions. These focus degassing magmatic fluids by the provision of fracture ground preparation, typically within competent host rocks, adjacent to the breccia bodies. Local dilational structures control the form of individual deposits which may contain bonanza gold grades at sites of fluid quenching and/or repeated mineral deposition.Early quartz veining and porphyry-related alteration is common and later gold mineralisation typically occurs in association with carbonate veining and Fe and base metal sulphides as Zn > Pb > Cu. The progressive cooling by mixing of the upwelling mineralised magmatic fluid with descending bicarbonate waters, produces characteristic zonations in carbonate compositions. These vary with distance from the porphyry source, from Ca through Mg, Mn and distal Fe types. Gold mineralisation is preferentially distributed within the Mn/Mg carbon-ates.

Jan 1, 1994

By Guarascio M, Massacci P

In process simulation, more reliable prediction of industrial results and evaluation of data for design purposes and process optimisation may be attained by the combined use of: the modelling and simulation of ore characteristics, and 2. the modelling and simulation of the process. It is well known that geostatistical methods allow the defining of models of orebodies in which the variables considered are the grades of the valuable components. These models are proper for reserve estimation, geostatistical contouring, design and simulation of the exploitation method, and, in addition, for evaluating the variability of the ROM which is expected to be fed to the processing plant. However, no data are normally incorporated in the orebody model in order to evaluate the ore characteristics relevant for a reliable process simulation. The procedure for process simulation aimed at predicting plant results normally used so far consists in collecting samples from different orebody sites and building up a so-called 'representative sample'. On this sample, the ore characteristics (eg liberation, washability, grindability, etc) and the processing tests are referred to as the 'average behaviour in the orebody', assumed constant. A more reliable methodology consists in collecting samples from different orebody sites, in performing tests to characterise the samples from the point of view of the process (ore patterns), and in using synthetic parameters (process features). The values of the parameters are processed using geostatistical methods in order to develop a model for simulating the feed to the process. The estimation may thus be referred to the amount of recoverable minerals instead of to the existing minerals. Furthermore, the selection of the processes, the sizing of equipment and the design of control devices, as well as the prediction of results, become more accurate and reliable.

Jan 1, 1993