Search Documents

The central thickened discharge system of tailings disposal takes advantage of the natural beach slope formed by sub-aerially discharged tailings, and the non-segregating properties of thickened tailings, to create a homogeneous conical stack. The need for containing embankments can be largely avoided leading to capital and operating cost savings. Methods for estimating beach slopes and tailings density, essential parameters for the design of such a system, are described. Case histories from three mining operations are used to illustrate the application of the technique, There are also seen to be potential advantages in the areas of water management, seepage, and rehabilitation. Laboratory and in-situ testing enable parameters to be determined.

Jan 1, 1991

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

The CSIRO acid alumina employs the essential steps of digestion, hydrolysis and calcination to produce pure alumina from ores too high in silica or too low in grade for the Bayer process. The two latter stages have been described in some detail previously but the digestion stage requires separate dis-cussion since ores vary widely in composition and reactivity. Kaolinitic clays require. roasting to 8000C to render the alumina soluble in the 11 per cent sulphuric acid used in the process while some ferruginous laterites require roasting to reduce the reactivity of iron minerals. The iron content of pregnant solutions is kept at a low figure by digesting at temperatures where the solubilities of ferric oxide or basic ferric sulphates are small. A.two-stage, counter-current digestion is necessary to extract a high percentage of alumina from the ores and to pro-duce a basic pregnant liquor, with an S03:Al203 ratio of 1. 9 suitable for high temperature hydrolysis. The second stage of digestion, called the modification stage, treats slightly acid liquors with exces's of ore in the temperature range 1200- 1400C. The first stage operates at 1700-190 C to extract further alumina from modification residues, using recycled acid obtained from later steps of the process. Both temperature ranges are critical for economic operation and for proper con-trol of the iron content of solutions. In batch experiments, thirty minutes is regarded as a suitable retention time for digestion and modification; ores which require much longer than this are less suitable for the process. Impurities. such assilica, titanium and vanadium oxides are discarded in the residue along with iron oxide and do not contaminate the final product. Bivalent metallic sulphates such as MgSO4 can build up in the circuit to a very considerable degree without affecting. product purity.Comparison with other processes shows that the C. S. I. R. O. process is superior for control of contamination by iron, which is the major problem in acid processes. The pure intermediate product (3 A1203. 4 S03. 9 H2O) is also more convenient for cal-cination to alumina than the hydrated aluminium sulphate usually recovered in other processes. Detailed cost comparisons must await pilot-plant evaluation of the C. S. I. R. O. process.

Jan 1, 1963

By Salley J, Gould WD

The stack-gas scubber effluent from base metal smelters often contain 20-100 ppm of oxidized selenium salts. Due to their toxicity, these must be removed from solution prior to release of the effluent to the environment. Many species of microorganisms including Corynebacterium diotheriae, Neurospora crassa, Candida albicans, Escherichia coli and various species of Salmonella are capable of assimilating oxidized selenium and reducing it intracellularly to red amorphous selenium. CANMET in cooperation with several companies has developed a biological process to recover selenium from dilute solutions. The laboratory, mini-pilot plant and the large industrial pilot- plant studies leading to the development of this process will be described.

Jan 1, 1990

This case study describes various aspects of establishing a laboratory facility for testing chemically-cemented fill materials. The applicability of data obtained from such a facility related to mine conditions depends on many factors: kind of data, type of testing facility, sample parameters (composition, geometry, size, etc.). The equipment employed must be adaptable, to accommodate variations in sample size and properties. The design, construction and operation of the testing facility is described, and its application to fill samples prepared from sulphides and oxides both chemically and naturally cemented. The present system was selected following an extensive study of equipment available for testing materials in the fields of rock mechanics and construction materials. The strength testing' facility incorporates Linear Variable Differential Transformers for monitoring both lateral and axial displacements during sample compression. The output from these and from other related instrumentation can be recorded or fed direct to a computer, enabling stress-strain data to be printed out while the test is in progress. Also described are controlled environment curing facilities which allow samples to be cured or weathered under different temperature or humidity conditions to simulate long-term ageing and in place conditions.

Jan 1, 1973

Misima Mines Pty Ltd (MMPL) operates a large open cut gold mine on Misima Island in the Louisiade Archipelago in Papua New Guinea. Misima Island lies approximately 600 km east-south-east of Port Moresby. The island is 40 km long by 10 km

Jan 1, 1994

By Harbort G. J

Jameson cell pilot plant trials were conducted in a number of areas in the Red Dome gold/copper flotation plant during 1991. The aim of testwork was to reduce the amount of cyanide soluble copper reporting in tailing to the gold leach plant, and hence reduce cyanide consumption. A number of these tests were conducted in parallel with conventional flotation columns. Laboratory tests were conducted to simulate the performance of the existing plant when compared with the addition of the Jameson cell allowing an extra sulphidising phase. This paper reviews the comparison of the Jameson cell and conventional columns in recovering cyanide soluble copper, while maximising copper concentrate grade. Key parameters that are investigated are residence times, air/pulp ratios, superficial gas recoveries and size by size recoveries. A brief comparison of performance of the Jameson cell and column in the controlled potential sulphidisation process is also presented. An estimation of the reduction in cyanide consumption is given.

Jan 1, 1992

By Grace B, Cunningham D

The poor quality of bore waters available to the Australian mineral processing industry creates a climate for crystallization of calcium based scales. If ignored, calcite and/or gypsum buildup can cause loss of production and costly unscheduled maintenance. This paper discusses the factors which contribute to scale forma- tion, methods used to monitor buildup and preventative measures (mechanical and chemical) that can be used. A case history il- lustrates the value of using chemical antiscalants.

Jan 1, 1991

By Tyson G. R

A novel system has been developed using computer imaging techniques to make on-line measurements of material on a moving conveyor. Meas- urements of the mass or volume of conveyor materials are important in large open pit mining operations such as those operated by the State Elec- tricity Commission of Victoria (SECV). Such on-line measurements can be used for monitoring and controlling the production and transport of coal or overburden, and to assist in maintaining production levels. This paper describes a conveyor burden volume measurement system which is currently under development at the Research and Development Department of the SECV and although targeted initially for use in the Commission's open cut mines, the system is suitable for use on any open conveyor system. A basic developmental system has been built to demon- strate the viability of the technique used and further work on the system is planned. The measurement technique and the major components which have been developed as part of the system are described, some comparisons are drawn with other existing measurement systems and potential errors and future development are discussed.

Jan 1, 1989

As the mining sector increasingly embraces the sustainability agenda, and implements thorough environmental reporting in support of its case for a continued æsocial licence to operateÆ, there is a need for ever-clearer metrics for key areas of impact. It is clear that natural waters are both the predominant pathway and main recipient of the environmental impacts of mining. A new approach to summarising the impacts of mining operations on water quantity and quality is proposed, adapted from an existing generic framework, which is increasingly used to quantify the æwater footprintsÆ of cities and nations. This includes both direct water use and ævirtual waterÆ use, implicit in goods and services used by the mine. In contrast to the existing formulation of æwater footprintÆ, it is here argued that it makes hydrological sense to express the water footprints of mines in areal terms, as equivalent catchment areas. It is also important in the mining sector to capture systematic changes in the scale of impact, which can be anticipated and predictively quantified over the full life cycle. This includes the essentially infinite post-closure phase, during which æremanent water consumptionÆ occurs, either through physical water loss (eg by evaporation from pit lakes) or by ongoing contamination of sizeable flows of natural waters. Methods for assessing the water footprints of mines are now available, and the time is increasingly ripe for them to be applied in earnest in environmental reporting. An example application to a mine in a humid subtropical area of South America is presented. In that case, the mine site itself extended over 106 ha, whereas the maximum water footprint exceeded this by a factor of 27. Although the water footprint can be expected to decline by a factor of ten immediately after closure, sustained evaporation from pit lakes and tailings dams with water covers will gradually increase the remanent water consumption rate, such that the final post-closure water footprint remains about 25 per cent of that encountered during the peak of mining.

Jan 1, 2006

By Abraham B. K, Jensen B, Gillies A. D S

The aim of the research was to investigate the feasibility of using an impedance cell and ratio-transformer bridge to measure solids content in coal slurry pipelines. It appeared that this technique could be developed to measure variations in conductance which correlate with solids content. Successful implementation of the measurement technique would have a variety of applications in existing coal wash plants and the potential for automatic process control. A small pilot plant was designed for a feasibility study. This was a closed loop system in which the coal was uniformly dispersed in a tank with a variable speed agitator and then circulated through an external pipe returning to the top of the tank. The impedance cell was located near the end of the external pipe. Slurry concentrations were varied from clean tap water to 50 per cent solids by weight with the addition of weighed quantities of dry coal dust. Ratio-transformer bridge measurements showed that variations in individual observations were equivalent to measurement errors of about two per cent. These probably reflect variations in concentration of the mixture in the pipe. Data for increments in concentration of one per cent indicate that this is about the limit of resolution of the current system. The paper discusses the principles of operation of the impedance cell and measurement system. Results from the pilot study and proposed improvements in the impedance cell design are examined.

Jan 1, 1995

By Milner SC

Four quartz latite rheoignimbrite units (units I to IV) mapped in the Goboboseb Mountains have been traced to their eruptive source, the Messum intrusive complex; this is a complex multistage ring structure (18 km diameter) with well defined gabbroic, monzonitic, and syenitic intrusive phases, and a central ring zone containing mixed rhyolitic to latitic agglomerates. Three of the four quartz latite units are correlated with the upper and lower (2 units) Springbok quartz latites outcropping some 90-130 km north of McIsum. This implies minimum volumes of 300-500 km for wits I and III (Lower Springbok) and 2200-2600 km for unit IV (Upper Springbok). This latter unit is still ti 300 m thick at its outcrop limit, some 130 km from Messum. Each of the four units represents single cooling units. Lithologically, each can be divided into three zones: A basal, dark grey to black flinty or glassy zone, often with highly attenuated fiamme (ressembling flow banding); a central massive and strongly recrystallised zone; and an upper variable zone which exhibit breccias, contorted flow banding, and amygdaloidal to pumiceous clasts. Their overall characteristics tend to be intermediate between ash flows and lava flows. The rheoignimbrites are interpreted as the oproducts of dense, high temperature (950¦-1100 C) ash flows which underwent rheomorphism and lava-like flow prior to their final cooling.These large scale eruptions are related to the initial rifting of Africa and S. America, possiby in response to a major hot spot.

Jan 1, 1990

The traditional concept of optimum drill and blast is that it is achieved when ore is produced at the lowest unit cost and, because of the complexities of most mining operations, represents a band which extends either side of an overall cost m

Jan 1, 1998

By Edwards A. B

The occurrence of gold so finely divided as to be invisible under the microscope, even at magnificatioIl; of 1,200 to 2,000 diameters, is rare, but not unknow;n.. Burg (1930) has described an occurrence of such "invisible gold" from the 25/37 vein of the Bradisor mine at Brad in the Siebengeburgen district of Rumania (Transylvania), in which the pyrite contained up to 150 grams of gold per ton (approx. 5 oz. gold per ton). Hoffman (1931) has described an epithermal silver gold ore from the Titiribi district of Columbia (South America), in which "invisible gold" to the extent of 150 grams per ton occurred in the pyrite, arsenopyrite and zincblende; and Haycock (1937) has recorded it in pyrite from the Surf Point mine (Canada), which contained no visible gold, but yielded positive testsfor gold whenever samples drilled from polished surfaces of apparently homogeneous pyrite were tested spectrographically.The examination of a cyanided pyritic concentrate, together with a sample of the ore from which it' was prepared, from the Dolphin East lode at Vatukoula, Fiji, carried out as part of the programme of the Mineragraphic Section of the Council for Scientific and Industrial Research, Australia, has established a further occurrence of "invisible gold" in pyrite and arsenopyrite. The Dolphin pyrite contains about 25 oz. gold per ton, and the arsenopyrite contains more than 33 oz. per ton.The concentrate has been prepared for the Mill Superintendent of the Emperor Gold Mining Co. by L. Mayger...

Jan 1, 1946

Many metallurgical beneficiation and primary concentrating processes rely upon discrimination of products from gangue based on particulate density of the different minerals and combinations of minerals in an ore. The basic definition of density is simple, but the apparent density that minerals exhibit when in the environment of commercial densimetric separation processes is more complex and is ill-defined. Measurement of the apparent density displayed by minerals in their separation situation is essential if modelling of plant performance is to be meaningful or when comparison of an existing operation with a æperfectÆ separation constitutes a part of an audit or of a plant control function. Seven methods of dividing ore samples into discreet density fractions are examined and criticised in this paper. The shortcomings, difficulties and potential errors arising from the use of each method are evaluated. Most of the techniques described have been used by the author and generally their faults are understood and the resultant first-hand experience has been used to overcome these faults. A simple new computer-assisted technique for developing meaningful densimetric data is described.

Jan 1, 2004

This paper summarises the results of a study carried out for the Sustainable Minerals Institute, University of Queensland, aimed at identifying the major water-related issues facing the minerals industry internationally and the research required to support the development of practicable solutions. An overview is given of the sources and uses of the worldÆs water resources and of the regional and global sustainability of water supply and management. Agriculture is the worldÆs major user of water; it wastes more water than the minerals industry uses. Water reform and its potential impact on the minerals industry are discussed with particular reference to Australia and South Africa. The sources, uses and management of water on mine and processing sites are outlined. Particular attention is paid to the importance of groundwater as a source of often saline water that can be used in mineral processing and for other purposes. Aquifer storage and recovery has the potential to help conserve water resources. Generally, the major uses of water on mining and processing sites are for mineral processing and refining and for the associated tailings disposal. Water consumption for these purposes may be reduced by recycling process water, using saline water, paying close attention to water management, thickening tailings and using techniques such as dry stacking and paste. A change in the minerals processing paradigm in respect of water use could come through research into new, improved and less costly dry processing techniques. The treatment of mine and processing water will be required increasingly before water is reused, stored, discharged or sold, and before sites are decommissioned. Research and development are required to reduce costs and develop new treatment methods. Mine closure and decommissioning raise a number of long-term water issues requiring continuing generic and site-specific research and development.

Jan 1, 2003

By M P. Sandy, J B. Simpson

The empirical stope design techniques developed by Mathews et al (1981) and refined by Potvin (1988) and others, have gained rapid acceptance in Australia in the 1990s as a simple, æfirst-passÆ means of designing primary stopes. However, it is recognised that these æstability graphÆ methods can only provide broad design guidelines. Recently published stability graphs (Hutchinson and Diederichs, 1996) encompass a wide range of geological environments, which are not discussed, and the influence of time and blasting practices cannot be easily reviewed. The æscatterÆ in the graphs must reflect, to some degree, different operating practices as well as subtle but important differences in the pre-mining conditions that are not adequately accounted for in the æmodified stability numberÆ. Development of a ælocalÆ, site-specific stability graph may overcome some of these problems. At NormandyÆs Golden Grove Operations, Western Australia, detailed reviews of stope stability performance, including Cavity Monitoring System (CMS) surveys, are undertaken for every stope, with the objective of developing a series of local stability graphs, customised to site conditions and calibrated in terms of æAverage Falloff ThicknessÆ (AFT). Cablebolting of stope hangingwalls is used to develop reinforced æbeamsÆ on each sublevel, effectively dividing the full span into smaller, more stable æsubspansÆ. By analysing stope stability performance in terms of fall-off, cost-benefit studies can be undertaken of the effect of cablebolting and other options for modifying stope spans. The approach used to develop the local stability graphs, and their integration into routine stope design procedures at Golden Grove, is described. The experience gained during stope extraction in the Scuddles orebodies has been successfully applied to the Gossan Hill æC-PanelÆ orebody. This methodology should be applicable to other underground mining operations.

Jan 1, 2000

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By McKew M, OÆRegan

Rapid access longwall mining' or 'longwail punch mining' is a proposed extraction method whereby longwall gate roads are driven into a seam directly from an opencut highwall. The longwall panel thus formed is retreated back to within 40 m of the highwall providing an extremely simple, reliable and therefore highly productive longwall mining system. The concept is of particular benefit for the recovery of isolated pockets of coal (adjacent to a highwall) not easily accessible from a conventional underground mine. As panel gate roads are driven directly from the open strip, minimal delays are incurred between the end of open cut and start of underground production, allowing the method to bridge the gap between open cut mining and a total underground commitment. The study was specific to the Bowen Basin, and given the likely conditions, no significant operational or geotechnical hinderances to the concept could be identified. It was therefore concluded that longwall punch mining would not expose the operator to any additional risks above that normally associated with the introduction of longwall mining. Thus, longwall punch mining is an attractive option, both operationally and financially, for open cut mines reaching their maximum economic Death.

Jan 1, 1988