Search Documents

DuPont is a chemical and energy multi-national of approximately 90,000 employees. Often regarded as the world leader in injury reduction and process safety management, DuPont operate 140 manufacturing sites around the globe. Conoco is a wholly owed subsidiary of DuPont which is involved in oil, gas and coal exploration.   Throughout this paper I will discuss DuPont statistics, developing a safety culture and training process as well as discussing possible short comings in the New Zealand safety focus. I will conclude with my recommended improvements and issues for New Zealand companies to focus on.   It is very difficult to compare DuPont and New Zealand statistics through lack of compatibility in recording methods and my ability to interpret ACC's Injury Statistics. However through considering DuPont's statistics, and comparing them to your own companies or departments, you will agree they are indeed impressive. I hope that by discussing DuPont's safety philosophy, and possible shortfalls within New Zealand Legislation many of you will find ideas and inspiration which will help you to further reduce your own injury rates.

Jan 1, 1997

By Hansmire WH

The 14.7 km Mt. MacDonald Tunnel beneath Rogers Pass in Canada used both drill-and-blast and machine boring methods. A unique ventilation system provides for diesel operations. The design featured minimum construction support and an unrei.nforced poured concrete lining. The west heading was excavated in a single-stage drill-and-blast operation. The east heading used a TBM top heading with a drill-and-blast keyhole bench. The choice of methods was controlled by varying geology, with up to 1,700 m rock cover. Construction performance and progress are evaluated.

Jan 1, 1987

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By Tuite M. J, Woolcock L. J

The Awak Mas gold project is located in the Province of South Sulawesi, Republic of Indonesia. It is situated 300 km by road north of the provincial capital of Ujung Pandang. The capital is readily accessible by air from Australia via Denpasar on Bali or the Indonesian capital, Jakarta (Figure 1). Elevations at Awak Mas range from 850 to 1400 metres above sea level in reasonably rugged terrain. The area is covered by primary and secondary (regrowth) rain forest. The region is subject to an equatorial-type tropical climate. The annual rainfall is a high 3000 mm most of which falls in the rainy season between March and June. In the lower valleys rice, cloves and chocolate crops are cultivated. Title to the project area is secured by a Contract of Work (COW) issued to PT Masmindo Eka Sakti (MES) on 23 October 1987 by the Government of Indonesia. MES was controlled at the time by New Hope Industries group of Brisbane. After New Hope had completed initial reconnaissance exploration of the area, Battle Mountain Gold Company (BMGC) farmed-in in 1991 and earned a 60 per cent beneficial interest in MES.

Jan 1, 1996

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

By Robins R. G

The dissolution of metallic copper powder in aqueous solutions of cupric sulphate under the influence of ethylene gas was investigated. The dissolution reaction stoichiometry obtained was: Cue+(aq) + Cu(s) + 2C2H4(g) = 2(CuC2H4)+(aq) The rate of formation of the copper (I)-ethylene complex in the above reaction was studied in a laboratory autoclave and the effect pH, temperature, ethylene partial pressure and initial concentration on the dissolution rate was measured experimentally and expressed theoretically in terms of several simple conceptual kinetic models. The results led to the selection of optimum conditions for the reaction and the suggestion of an "ion-molecule reaction" mechanism to explain the very low activation energies for the reaction system. The area of application of this reaction lies in the direction of refining impure copper such as cement copper. Several experiments were performed in which an acidified solution of cupric sulphate under ethylene pressure was used to dissolve copper from the cement copper powder in the form of the copper (I)-ethylene complex, followed by the release of gas pressure to disproportionate the complex and precipitate a purer metallic copper.

Jan 1, 1987

By L Lagoeiro

The samples studied in this paper were derived from the iron oxide facies of iron formations (IFs) of the Quadrilßtero Ferrffero, south-eastern Brazil. The rich-iron oxide varieties of the IFs can be regarded as Fe-O systems because they consist predominantly of aggregates of haematite and magnetite crystals. The study was based on carefully selected samples in which magnetite crystals occur as isolated large crystals set in a matrix of haematite grains. Optical microscopy and an electron microscope equipped with an electron backscattered diffraction (EBSD) system were used to investigate the microstructural and crystallographic relationships involved in the phase transformation between magnetite and haematite. The magnetite crystals in the IF samples are partially transformed to haematite and this process is also known as martitisation. This transformation occurs along the crystallographic planes {111} of the magnetite producing a characteristic triangular pattern of interlocking lamellae of transformed haematite crystals that are oriented parallel to octahedral plane {111}. This new generation of haematite is referred to martite because of the martitisation process. EBSD analyses show that the magnetite and the new haematite crystals, martite, share crystallographic planes of highest atomic density, eg {111} and (0001), respectively, possibly due to the ccp and hcp atomic arrangement of the two crystals. Stereographic projections of these two planes therefore coincide when the maxima of their poles are plotted. However, the crystallographic orientation of the haematite crystals in the matrix shows maxima of (0001) poles that do not coincide with those of {111} planes of magnetite. Consequently, it is concluded that the direct transformation to haematite crystals retains the crystallographic orientation memory of the former magnetite crystals, possibly due to the similar manner whereby their atoms are packed together in the crystal structures. On the other hand, no such relationships are observed between magnetite and haematite crystal in matrix. This suggests that haematite grains in the matrix may have been formed by other processes rather than those involved in the iron oxide transformation observed within the magnetite grains.

Jan 1, 2008

By Qisu W

The ground vibration produced by the bench blasts of a single hole and a row of two or three holes is recorded in an iron mine. Using the seismic signal generated by a single-hole shot as the source function, we have developed a computer program of a simulating ground vibration by bench blast. The reasonable delay time of blast in the iron mine has been discussed tentatively with the Fourmap invented by Anderson, D.A. The seismograms measured from the single-row blasts of two or three holes have shown the method of simulating vibration is feasible on the whole. For large scale production blasts, a combination of the vibration simulation and the high-speed photograph is used to choose the delay Time.

Jan 1, 1990

By A Nisbett

The largest single operating loss in many hydrometallurgical plants is the poor recovery of leached product in the solids sent to tailings. Any reduction in the concentration of the valuable species in this stream will improve the project economics. Conventional design, to reduce the soluble loss, is to increase the number of wash stages or the wash/water ratio. This approach is limited in effectiveness as it can only reduce the soluble loss to that dictated by the concentration in the returning solution. For copper plants this concentration is set by the recovery in the solvent extraction (SX) plant. When using a single grade of SX feed a single grade of SX raffinate is produced generally with five to seven per cent of the copper still remaining in solution. An alternative approach has been developed by Cognis Corporation and implemented on a number of recent projects using engineering input from Miller Metallurgical Services. The SX plant feed is æsplitÆ into two different streams: a high-grade stream containing up to 75 per cent of the copper and a low-grade stream with the remaining copper. This Split-CircuitÖ concept has significant benefits in terms of both copper recovery and reduction in acid costs. The high-grade stream has the bulk of the copper removed and the raffinate sent directly back to the leach; to fully re-use the acid that has been generated during extraction in the SX process. The recycling of this higher concentrated acid stream considerably reduces the acid in the raffinate sent to washing steps. It represents a significant saving in acid consumed via the tails stream. The low-grade stream has a significantly lower SX feed grade and hence produces a lower raffinate acid and copper concentration. This lowers the economic species in the wash solution and hence reduces the soluble loss accordingly. Other operating improvements are realised with lower neutralisation costs (with the lower acid in the wash stream) and from a decreased need for in-circuit neutralisation to improve SX performance. The SX plant itself is also split into a high-grade extraction and a low-grade extraction stream to enable the low-grade raffinate to be produced. A number of circuit alternatives have been utilised that have provided a range of benefits. The circuit concept has been included into both new and existing plant operation. As a result of this experience other methods of incorporating the concept into a circuit have been developed.

Jan 1, 2005

An empirical kinetic model is discussed that enables the number of stages in a carbon-in-pulp plant and the amount of carbon in each stage to be calculated for any desired metallurgical performance. It is shown that a knowledge of the kinetics of gold extraction by activated carbon in each stage assists plant operators in the important' areas of process control and optimization. Factors such as mixing efficiency, concentration and distribution of carbon through the plant, bypassing of pulp through a stage, and carbon poisoning are examined. The resin-in-pulp process for the extraction of gold cyanide is also discussed, and the chemistry of absorption and elution on strong- and weak-base resins is examined. In addition, operating results from a small-scale resin-in-pulp pilot plant are presented, and various applications in which resin-in-pulp may be preferable to carbon-in-pulp are discussed.

Jan 1, 1982

By J M. Palin

Hydrothermal scheelite precipitated in fault-veins at Paradise, Bonnie Jean, Davidson's and Glenorchy mines display chemical variability involving REE patterns that are transitional between two end-member types. Type I is a MREE-enriched pattern with no or a small positive Eu anomaly. Type II is a flat to MREE-depleted pattern with a strong positive Eu anomaly. The chemical inhomogeneity of these scheelites can be explained by a model of fractional precipitation of REE, with preferential removal of MREE from the fluid during precipitation of scheelite. Irrespective of the mechanism responsible for scheelite precipitation, the source of dissolved constituents is different for scheelites from the Paradise Mine. Bonnie Jean, Davidson's and Glenorchy scheelites formed from LREE-enriched fluids whereas Paradise scheelites precipitated from fluids that were lower in LREE. These inferred fluid characteristics cannot be linked unambiguously to specific source rocks in the region, but could suggest that scheelite deposited in the Paradise fault-vein reflects a more mafic source of REE possibly greenschists, whereas the REE in scheelite from the other mines suggest a more felsic source.

Jan 1, 2003

By Tonegato S, Wood M

The lack of objective data on roof bolting machines, bits, rods and overall system has created the need for an objective assessment of roof bolting. This work outlines a test rig for such objective assessment of component parts of the roof bolting system.

Jan 1, 1986

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

By P C. Hagan

Production scheduling is often reliant on an estimation of a mineÆs trucking capacity. While this mechanistic approach is relatively simple, it often over-estimates actual throughput resulting in under-utilisation of downstream process and a shortfall in revenue. An alternate approach has been developed that recognises the interdependency between processes in the mine production system including materials loading, haulage and crushing. This approach incorporates a heuristic model based on queuing theory that accounts for the variability in performance of individual processes and that this paper presents the results of a study comparing the conventional approach to mine scheduling with a capacity constrained model at a large open cut mine having a truck and shovel fleet. The capacity constrained model consistently predicted a lower material throughput compared to the conventional approach. Differences in throughput between the two approaches were found to increase with loading time, for example when loading time exceeded 3.9 minutes there was a shortfall of up to 40 per cent in estimated throughput. Longer travel times tended to ameliorate any differences. When applied to a mine schedule that extended over a two and a half year period, the difference was equivalent to a shortfall of nearly eight per cent in total material movement.

Jan 1, 2007

Over the past 15 years, Artificial Intelligence (AI) techniques have shown promise of providing the ability to capture `human intelligence' into a computer program. The sub-fields of Expert Systems and Artificial Neural Networks are finding increased use in industry to perform tasks previously considered the domain of human thinking. But, are these methods just a new type of software much like that of the past or is real magic hidden within the lines of code? Will this field continue to enjoy high growth rates and if so, what developments will we see in the near future? Which algorithms and methodologies will continue to grow? This paper discusses a number of paradigms which can be used to create successful applications. There are certain barriers; some psychological - some linked with knowledge acquisition, that must be overcome or avoided to ensure system performance. Development time also requires careful consideration before embarking on an Al project. The paper focusses on constructing goal-driven systems that transfer high-technology solutions from the research laboratory to the plant floor. Respect for system users is of paramount importance - whether their involvement is to access contained information or to participate in program maintenance as new knowledge becomes available. Examples of successful and unsuccessful AI implementation in Canadian industry and academia provide evidence of the importance of this issue. The paper also examines some current constraints on applying AI in the real-world. Among these problems are automated knowledge acquisition, methods to acquire data during run-time, real-time systems (hardware versus software), explanation and justification features and adaptive/leaning systems.

Jan 1, 1995

By M P. Sandy

Some Western Australian underground mines are challenged by very high stress gradients. This environment frequently results in poor induced ground conditions and damaging seismic activity. In some cases, rockbursting or squeezing ground has been observed as shallow as 250 m below surface. Very few mines operating at depths greater than 500 m experience no stress-related issues. As a general result of this difficult environment, there are a growing number of mines that are now challenged or have been closed by induced geotechnical problems. Often, the up-front savings or perceived advantage of an inappropriate mine plan may be entirely lost to the real cost of managing the hazards, or a write-down of reserves resulting from access difficulties will diminish the economic position of the mine. From an engineering perspective, it is best if stress-related hazards can be proactively minimised, because reactive measures offer less improvement in risk exposure. In this paper, some examples of sequencing techniques for managing difficult environments are contrasted with examples from mines where developing hazards have adversely affected production or the economic viability of the project.

Jan 1, 2003

Wetherstones gold deposit is located just east of the township of Lawrence, in the Otago District of the South Island, New Zealand. The paper will describe aspects of the mining and exploration history of the Wetherstones gold field, current knowledge of the geology of the deposit, and speculate on possible outcomes of exploration in the modern era.   As at the famed Gabriels Gully situated nearby, most of the Wetherstones gold is/was contained in, or recycled into modern drainages from, the Blue Spur Conglomerate (æBSCÆ). The BSC is the basal member of a wedge of auriferous non-marine sediments of latest Cretaceous age which are tilted against the Tuapeka Fault Zone, a structure of regional dimensions. In particular mineralisation of elevated grade (which cannot yet be reliably estimated) appears to be concentrated in an elongate basement depression (ægutterÆ) of width around 100 m, variable thickness to a few metres, and axial length in excess of 500 m. The gutter plunges from the base of alluvial mining (where it has been partly exploited by underground methods) to depths of more than 100 m, beyond which it remains open and untested.   The prospects for a revival of mining at Wetherstones depend upon confirmation of what is here inferred to exist, and the discovery of additional gold. The economic prospects of the project however are enhanced by what is known or indicated of the geographic location, and anticipated geologic, mining and metallurgical characteristics of the mineralisation, and consequent anticipated environmental management issues.   The recognition of gold contained in pyrite in the BSC represents an upside to project economics which has never previously been evaluated. The Wetherstones Basin covers more than five square kilometres in areal extent. There is no modern exploration record of the majority of this area, leaving open the prospect of the discovery of additional gutters, and primary mineralisation in the underlying schist.   Australasia Gold Ltd has embarked on a program to reassess the potential resources of the Wetherstones gold mineralisation, and to evaluate the feasibility of mining.

Jan 1, 2004

By Moon N. T, Torrance A. C

This study has considered the effect of mechanical shock on the resilience of the glass microspheres commonly used to sensitize an explosive emulsion. The damage to the glass microspheres caused by detonating cord, emulsion manufacture and the manufacture of the glass microspheres were considered along with the effect of sensitizer concentration on explosive performance. Reductions of up to 50% in the glass microsphere concentration of an emulsion explosive can result from poor initiation practice, such as the use of high strength detonating cord as downlines during initiation. Laboratory results suggest that detonating cords of strength greater than 3.5 g/metre should not be used as this can seriously affect explosive performance, particularly in small diameter charges. This reduced performance results from damage to the sensitizer elements and recrystallization of part of the emulsion phase.

Jan 1, 1990

By Bell LC

Overburden removal, mining and reclamation are now accepted as the basic operational steps involved in the winning of coal by open cut methods. To attain the lowest operational cost, the recontouring and revegetation of spoilpiles must be planned concurrently with the planning of overburden removal and mining. The earthworks associated with reclamation work on spoilpiles often account for 75 - 90 per cent of total reclamation costs. Experience at Callide Mine has shown that the way that spoilpiles are contoured does influence water retention and can reduce erosion from rainfall run-off. However, provided the recontoured slopes meet'Mines Department specifications, the quality of reclamation work is judged not by the quality of the earthworks but by the plant regrowth on the reshaped surface. Thus it is the quality of the revegetation which is of prime importance. For vegetation to be successful, time must be spent on planned research into methods of overcoming plant nutrient deficiencies and selection of suitable grass and tree species. The research programme undertaken at Callide Mine consists of three stages :- laboratory studies glasshouse trials field trials

Jan 1, 1978