Search Documents

The procedure used for Truck Maintenance is described systematically in this paper. Emphasis is given to manpower required, work facilities, daily maintenance and oil sampling procedure. Scheduled Preventative Maintenance Service, Electrical Service, Component Change, Truck Overhaul and Outside Contractors are also discussed. The system used, achieves the required results with an average haul truck availability in 1981 of 87.9 per cent. INTRODUCTION Situated on the Island of Bougainville, in Papua New Guinea, the Bougainville Copper mine nestles in a valley near the crest of the Crown Prince Range, between 600 m and 980 m above sea level. The mine is serviced by two towns, Arawa - an open town on the Coast and Panguna at the Mine Site. Currently Bougainville Copper operates an open pit mine removing an average of 198 000 dry metric tonnes of material per day (115 000 tonnes ore and 83 000 tonnes of waste) with a fleet of electric shovels and 154 tonne electric haul trucks.

Jan 1, 1982

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

By R Lovel, P Fung, J Manuel, M OÆCo

The iron blast furnace is the most widely used and efficient producer of liquid iron. The integrated steel works is however under environmental pressure largely due to emissions from sintering and coking. The combustion of coke breeze during sintering contributes to greenhouse gases (eg carbon dioxide) and is the source of much of the emissions of SOx and NOx. Coke breeze, the fines produced during coking of coal, is also suffering supply issues as coke demand increases while coking capacity is constrained by environmental concerns.CSIRO Minerals has been investigating the use of wood biomass/char as a substitute for coke during sintering. Wood biomass, or char produced from it, is an attractive carbon source as carbon dioxide can be sequestered into growing biomass prior to combustion. It has great potential to reduce the emissions from integrated steelworks and improve their environmental acceptability. Harvested biomass/char is also a renewable and sustainable resource. Samples of pine wood flour, sawdust and red gum wood char were characterised and used in small-scale granulation and sintering tests. Red gum char granulated as well as coke and could be used to make acceptable sinter. Large-scale sinter pot test were conducted with char to produce sufficient sinter for ISO quality tests and calculate sintering performance parameters. Results showed that coke could be completely substituted by red gum char during sintering without loss of quality and with actual improvements in sintering performance. Furthermore, gas analyses made during sintering showed that there were significant reductions in SOx and NOx when char was substituted for coke. It is anticipated that the results reported here, although preliminary, will stimulate an increased effort into further research on the use of char in iron ore sintering.

Jan 1, 2004

By C OÆKeefe, A Thomas

Boom time in the mining industry has presented mill operators with several unique challenges including the need for increased throughput while being constrained by a shortage of skilled labour and aging capital equipment. New instrumentation technology that provides reduced installation costs; no process down time for installation; and reduced maintenance costs and labour requirements; has been introduced to address the labour situation while maintaining production. This new tech- nology also enabled more accurate and reliable process measurements thus providing the capability for operators to maximise throughput with their existing capital equipment. This passive SONAR based technology can accurately measure the volumetric flow rate of single phase and multiphase fluids as well as the amount of air entrained within slurries. This is accomplished in a non-invasive manner. This paper will describe the principle of operation as well as the application of the technology to critical minerals processing applications. Included will be operational examples comparing the SONAR measurement performance to traditional measurement techniques. These examples will include hydrocylone feed flow, flotation concentrate flow, and slurry streams containing magnetic ores. Actual plant data will be presented as well as a discussion on the operational advantages such a measurement capability.Also described will be the power of the technology platform to provide novel process monitoring and control capabilities such as pipeline sand-out prevention and pipeline acoustic monitoring.

Jan 1, 2009

By E R. Ramanaidou, M S. Piggott

Transport to and handling of iron ore at Port Hedland, Western Australia, results in the generation of airborne particulates that contribute to the atmospheric dust load, with concerns about potential local environmental impacts (eg mangrove swamps) and possible human health implications. Mineral and chemical characteristics of the Background soil samples were contaminated with particles of iron ore as martite octahedra and grains of micro-platy hematite as detected by scanning electron microscopy (SEM) in the 2.5 - 10 ¦m and 10 - 50 ¦m size fractions. Fossilized wood fragments similar to those observed in Yandicoogina fines ore were also detected in some background soil samples. With a predicted increase in demand of channel iron deposits (CID) ores and the inherently dusty Marra Mamba ores (eg West Angelas, MAC, OB29/30/35, Marandoo), in conjunction with particulate emissions from hot-briquetted iron and direct reduced iron (HBI/DRI) processing plants, there is the potential for additional sources of anthropogenic dust to contribute to background levels. Mineralogical and chemical characterisation of the entire range of particulates that could be produced is necessary for a complete understanding of their potential impact on the local environment.

Jan 1, 2002

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

By Anderson J. M, Gillies A. D S, Jones N

There are a number of current theories in relation to methane migration and emission into workings following underground coal mining activity and some controversies do exist. Mining causes changes in the stress regimes in surrounding strata and results in fracturing. Permeability increases and methane flows into workings under a pressure gradient. The effects of stress on permeability depend on the physical properties of the coal and surrounding strata. Methane emission also depends on the original methane content and the proportion which will be liberated. There are several methods for determining in situ methane content and desorption characteristics of coal samples and several methane prediction methods but clearly more research is necessary to achieve an adequate predictive model.

Jan 1, 1992

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By Clark K. N

The need for and advantages of simulators in iron ore pellet induration research are described. The approaches to simulation and the techniques to carry it out are discussed in detail covering drying and firing for the straight grate process. The CSIRO simulator design is described and some errors in simulation are discussed.

Jan 1, 1974

Potential hlghwaJl mining reserves in Australia are large, but geotechnical and operating conditions are quite different from those where highwall mining has evolved in the USA. In order to achieve safe and effective resource recovery, equipment and procedures should be developed to penetrate 250 m in the Australian mining environment. This paper identifies key auributes to be incorporated in such machinery and methodology. These suggestions are intended to promote discussion on innovations to satisfy Australian requirements for highly productive, safe and environmentally acceptable techniques.

Jan 1, 1993

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986

By Royston, Woods R

ANI Bradken Vortex Pulp Lifters and Grates, both as original equipment and retrofitted to existing SAG mills, are now in field operation. The development of the Vortex leading curve pulp lifter was based on an analysis of traditional radia

Jan 1, 1997

By D Giles

We present plate tectonic reconstructions, showing that porphyry-type ore deposits are spatially and temporally linked to ridge subduction. A reconstruction of the Peruvian subduction system reveals an immediate metallogenic response to the arrival of the Nazca Ridge at the subduction trench, followed by southward migration of the zone of metallogenic activity due to the lateral migration of the zone of ridge subduction. A similar pattern is recognised in central Chile , where the spatio-temporal distribution of giant ore deposits coincides with the arrival of the Juan Fernandez hotspot chain at the subduction zone. We conclude that there is a spatial and temporal link between ridge subduction and ore deposit formation, with high metal fluxes concentrated in zones of ridge subduction. Thus, the recognition of tectonic patterns associated with ridge subduction can provide insights into predictive mineral discovery by enhancing our ability to predict the position of large mineral deposits in other modern and ancient orogens. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Terlich R. E, Finlayson J. M

A combination of high virgin rock temperatures, deep workings and extensive utilisation of heavy diesel equipment has presented North Mine (A Division of North Broken Hill Limited) with challenging ventilation problems. These problems have been addressed in a variety of ways which include in the order of 6000 kM of underground refrigeration. The future of North Mine depends on the successful development and extraction of ore in excess of 1100 m below the shaft collar using mechanised cut and fill mining. The success of this will depend on the installation of a complex chilled water reticulation circuit in this area. This will involve planning and constriction of a number of large dams, installation of pups and turbines, and the successful commissioning of several large water to air heat exchangers.

Jan 1, 1988

Broken Hill South Limited's discovery of phosphate deposits in the northwest of Queensland in 1966 prompted intensive exploration which has proved phosphate rock in excess of 2,000 million tons at ten separate deposits.Systematic exploration for phosphate in Australia was initiated by the company in 1964. Early in 1966, an investigation of oil wells in the Georgina Basin in the Northern Territory and Queensland revealed widespread anomalous phosphate in early Middle Cambrian Beetle Creek Formation and Thorntonia Limestone. Phosphorites recognized in oil wells in the southeastern part of the Basin, Queensland, led to the discovery of the Duchess deposits. Exploration of the Beetle Creek Formation since 1966 has disclosed nine other sizeable deposits north of Duchess around the eastern margin of the Basin. The Lady Annie and the adjoining Lady Jane deposits, by reason of their location, 160 miles south of the Gulf of Carpentaria, are expected to be the first to be brought into production.Beneficiation testing and engineering investigations commenced in 1967. Transport between the deposits and various port sites in the Gulf of Carpentaria has been extensively studied and a slurry pipeline as a means of transport to a deep water island port, is now being investigated.

Jan 1, 1971

By Yao S, Wang P, Zhang C

The Zhilingtou Au-Ag deposit is situated in the eastern part of the complexly deformed and metamorphosed South China Caledonian Fold Belt. It consists of seven orebodies that are almost exclusively hosted by biotite plagioclase gneiss of the Precambrian Chencai Group. They form an apparent en echelon pattern in both cross-section and level plan. Three different ore types, based on mineralization textures, have been recognized within the Zhilingtou lode. These are Au-Ag-rich quartz veins, Au and Ag-bearing silicified rocks and Au-Ag-containing altered rocks with quartz stockworks. The mineralization is principally composed of electrum, argentite, pyrite and minor sphalerite, galena as well as traces of hessite and chalcopyrite plus a gangue assemblage of quartz, rhodonite, sericite and chlorite. Fluid inclusions related to Au-Ag mineralization yield a wide range of homogenization temperatures from 110 to 447¦C, with two distinctive peak values at 250-300¦C and 350-400¦C respectively. S30Si values of quartz veins and silicification from the three stages of mineralization range from -0.1 to -0.4%o. The mineralization at Zhilingtou is interpreted as forming by recirculated meteoric water extracting ore-forming elements from metamorphic rocks due to Mesozoic volcano-magmatic activity.

Jan 1, 1995

By Y Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, aO2-, and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of aO2-, which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions.

Jan 1, 2000

By Nagai K, Moriyama K

Toyo smelter has been making s veral efforts to reduce and diversify energy for dealing successfully with such :n:;rgy problems as the first and second oil crises. ::,specially it is one of th:; most important subjects to substitute oil by alternative: energy source, because oil is expensive and unstable with respect to its supply. t _'hercfore i was decided to propel tnC ezhstitution of coal *jr oil. in the first place, the supple- mental fuel oil in the reaction shaft was replaced by oil to coal in 1981, and then th, fuel substitution of pulverized coal was achieved in the steam superheater in 1984. 3y these fuel substitutions about 7u,' of the total fuel energy at 2oyo smelter has been replaced by coal. in this paper the fuel substitu- tions at loyo smelter are described in detail.

Jan 1, 1987

By Clark GH

Batu Hijau is a porphyry copper-gold deposit located on Sumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54000m of drilling in 105 diamond drill holes over a surface area of 1.2km2 and to a depth of 1000m below surface (412m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55g/t Au (variable cutoff) from an open pit in the higher grade portion of the resource. The deposit is associated with a caic-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200m diameter at surface to 500m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbldykes or postmineralisation intrusive rocks.

Jan 1, 1995

An improved method of sample recovery for use with rotary percussion drilling has been developed. Cuttings can be recovered continuously from either dry or wet drilling, and the recovery under dry conditions is seldom below 99% of the cuttings brought to the surface by the rig. The system is designed for use with top drive drilling rigs using flush-jointed drill rods. The key feature of the system is a self-aligning mechanical seal around the drill rods. The sealing unit is removably fixed to a collar section of cas ing. the cuttings are recovered in a plastic bag attached to the bottom outlet of a cyclone. A valve at the bottom of the cyclone permits the cuttings representing various depths to I,e recovered separately for examination eind 0(iclysis. [u the Iron Monarch quarry, two percussion holes were drilled to depths if 30 metres and 28 metres using the unproved sample recovery system, and diamond drill holes bored 1 metre from each percussion hole. Samples from each hole were sectionalized over metre intervals and analysed for iron, silica, alumina and loss on

Jan 1, 1976