Search Documents

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

By Konishi Y, Morioka Y, Okabe K

A part of the results of dissection survey of Chiba No.1 blast furnace, Kawasaki Steel Corporat- ion, is presented. Distributions of coke size and of slag and metal holdup are shown in the region of the dropping zone. A similar relation to the irri- gated packed bed is obtained. The distribution of coke size, coke temperature and liquid holdup are measured in and around the raceway. The shape of raceway in the horizontal and vertical sections indicates that each raceway worked individually. Liquid flow in the dropping zone and around the raceway on the basis of holdup measurements is Discussed.

Jan 1, 1981

A laminar-flow furnace was used to study the combustion of four flotation concentrates (chalcopyrite, pyrite, galena, and sphalerite) in air at temperatures up to 1400¦C. A special- Iv developed two-colour pyrometer was used to measure the temperature of individual chalco- pvrite and pyrite particles as they underwent combustion. Chalcopyrite and pyrite ignited with very high rates of reaction at air tempera- tures above 480 and 600¦C respectively, forming molten products. Galena and sphalerite required temperatures in excess of 700 and 1200¦ respect- ively to attain equivalent rates of reaction. The high rates of reaction for galena and spha- lerite were caused by vaporization. Temperature measurements for chalcopyrite and pyrite are reported here, together with vaporization measurements for chalcopyrite, galena, and Sphalerito

Jan 1, 1980

By J J. Jiang, M Reimnitz

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is mining through a dense network of disused level workings and open stopes of greatly varying sizes. The condition of the stope crowns and remnants is often unknown, and ultimately these structures become a significant proportion of the production floor and pit walls. Significant seismic events and occasionally rock bursts often occur in the underground workings. Seismicity is becoming an issue to the viability of the KCGM Fimiston operations. KCGM needs to take a leading role in understanding mine-induced and regional seismicity. The seismic system trials were initiated in the Fimiston Open Pit in 1996 using the ISS system. The initial system included two triaxial geophone arrays and two triaxial accelerometer arrays installed into two boreholes. The main objectives of the trial were to investigate the suitability of the two types of sensors and the detectability of seismicity in the pit. The trial was regarded as a success and the system has been expanded and improved. The current system consists of 12 triaxial geophone and accelerometer arrays and nine uniaxial geophones. The 12 triaxial arrays are installed in nine boreholes drilled from the pit and the nine uniaxial geophones are installed from underground level workings about 660 m below the original surface elevation. The system is designed to provide seismicity coverage for the entire pit area that is about 2.7 kilometres long, 1.5 kilometres wide and about 300 metres deep. The accuracy of the source location has always been a challenge due to the existence of the dense concentration of stopes and lack of the sensors. It is uncommon to have direct ray path for the seismic waves to propagate to the sensors across the strike, hence sensors have been located along strike and under the old workings. This paper discusses some of the challenges associated with seismic monitoring near mine remnants and seismically active faults. The results of the seismic monitoring are presented, and contrasted to results of three dimensional boundary element numerical modelling. The impact of the seismicity upon pit slope stability is briefly discussed.

Jan 1, 2003

By McClarnon D. J

This paper aims to provide the reader with an insight into the field of computer graphics and Virtual Reality (VR), and show how both have been applied to the general area of Free Steered Vehicle (FSV) operations underground. It first explains this developing computer technology and explains its advantages over existing CAD based solutions. This paper deals with the graphical applications and implications of building models within a computer's memory. It then continues to describe the problems with Free Steered Vehicle operations. The work already carried out in the field of VR is explained, and the production of a VR system addressing the problems with fitting cameras to aid the driver's field of view is detailed. Another possible use of VR is also explained - the concept of risk regions, demonstrating its uses in the examination of proposed operational methods. Examples of possible uses are given, and its potential advantages over existing methods discussed. A case study of a computer-generated video involved with the safety of operations of FSVs is also presented. This addresses the precautions that pedestrians should take to ensure safe working in areas where FSVs are operating. This paper then concludes with possible further applications for computer graphics and VR, and the on-going research into these two technologies.

Jan 1, 1995

By Garg R. K

Himalayan ranges on the northern border of India are source of many perennial rivers and suitable sites for large dams have been located therein. However, Himalayas are young mountains and comprise of comparatively weaker rocks having adverse geological features like shear seams, thrust zones, minor and major faults and intense jointing. Tehri dam project under construction, is located in lower Himalayas. It envisages construction of a 260.5 m high earth and rock fill dam and an underground power station of 2000 MW (Eight machines of 250 MW each, four of which will be reversible) installed capacity. This dam will be the highest and the underground complex will be the largest to be constructed in India in the Himalayas. The under- ground complex comprises of 25 km of tunnels varying in diameter from 6 m to 11 m and seven large cavities of various sizes, the biggest being 22 m in width, 194 m in length and 65 m in height. Rock formation in the power house complex belong to phyllites having various joint sets spaced from 0.5 m to 3 m. Due to the poor geological conditions and closely spaced net work of large cavities, the planning, analysis and design of the cavities is a challenging job. Many aspects have to be considered in determining the sizes, locations and orientations of the various cavities taking into account the properties and jointing pattern of rock mass, functional requirements and economics. Correct evaluation of loads and forces is necessary for economical design of supporting system for the various cavities. Rock loads on the roof of cavities and their supporting system will be assessed with the help of the latest methods. The stability of the rock mass around the cavity will be evaluated by elasto- plastic method using finite or boundary element techniques. A scheme of field investigations, laboratory tests and instrumentation for deter- mining rock properties in preconstruction stage and for monitoring behaviour of the underground cavities during and after construction is envisaged.

Jan 1, 1987

By Gordon N

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987

By Veloso L, Alvarez O, David D

Cerro Colorado operations The Cerro Colorado Mine is located 150 km east of Iquique in the Atacama desert of northern Chile. The mine is wholly owned by Rio Algom Limited of Canada and produces copper metal using a bio leaching process. Tw

Jan 1, 1998

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

The results expected from a longwall face can best be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the effective operating hours, and the utilisation.The effective operating hours are determined by a number of scheduling factors which include the proportion of manned time to calendar time, the effective shift factor (effective time to manned time) and the move times.Analysis of the results achieved on the last 121 completed longwall panels in Australia (1984 onwards) shows a significant trend between 'actual tonnes/manned hour' and 'ideal production rate' (the measure of the capacity of the installation).Using 1982 'state of the art' longwall equipment, (the average in use in the seven year period), it should be possible to produce around 2.7M tonne/year ROM from a mine with one longwall. Few mines are achieving this.A review of production scheduling factors and general natural hazards affecting some mines suggests three things.1. Whilst some increase in average effective hours has followed the CIT decision, further improvement is possible at many installations.2. Many mines subject to general natural hazards, such as high gas make and high general stress, have found effective solutions and achieve the same utilisation as the overall average.3. A small number of faces within such mines have been severely affected, some less so. The most severe effects of natural hazards appear to be very site specific. This emphasises the need for detailed investigation of the causes, and development of means of predicting their presence. Only then can either satisfactory technical solutions be found to overcome the problems or prior decisions be chosen not to mine badly affected panels.

Jan 1, 1991

Maps of mineral grade used to assess mineral reserves are most commonly generated using one of the many estimation methods available such as inverse distance weighting or ordinary kriging. Most such maps incorporate a degree of spatial smoothing which is an integral part of the averaging process. In deposits with highly variable grade which include many gold deposits, this smoothing can mask the detailed geometry of the mineralization at the economic cutoff grades being considered. In underground mining, a knowledge of this geometry is important in the choice of mining method and thus in the assessment of the minable reserves.The method of conditional simulation in geostatistics can be used to generate maps of grade which reflect the actual spatial variability of grade as measured through the variograms of the drill hole data. Simulated maps can provide a number of equiprobable images of the mineralization geometry from which a more appropriate mining model of the mineralization can be developed. Multiple simulations can also be used to assess the uncertainty existing in the current knowledge of the reserves.

Jan 1, 1990

Using normal low pressure filtration methods for the dewatering of fine china clays, the best that can be achieved is cakes with about 30% moisture. In order to get the moisture levels down to acceptable levels the traditional method used is thermal drying, which is both costly and dust creating. It was to improve this process that ECC International embarked upon a programme of development of filtration equipment using high pressure to achieve significantly lower moisture levels. This development work investigated several design philosophies and culminated in the production of two quite different solutions. The High Pressure Plate Press uses round plates / chambers of one metre diameter and a filtration pressure of 70 bar. This press is fully automatic and produces a surface dry cake that has sufficient plasticity for the further processing that is required on specific qualities of china clay. The TUBE PRESS on the other hand uses a unique design configuration and operates at a filtration pressure of 100 or 140 bar, depending upon the model. The TUBE PRESS produces a brittle, surface dry cake that is easy to handle and a filtrate that is usually crystal clear. The TUBE PRESS achieves a much higher degree of separation than is possible with conventional equipment, which is particularly important if the filtrate is the product. Over the past 15 years plants incorporating both HP Plate Presses and TUBE PRESSES have been installed in the china clay operations of ECC International and are giving excellent trouble free service. The TUBE PRESS has also proved to be extremely versatile, effectively dewatering a wide range of fine particled slurries, in a number of diverse industries.

Jan 1, 1989

INDEX OF CONTENTSIntroductionThe slag samplesGranulated SlagGlass-spinel-magnetite-metallic leadRapidly Chilled SlagSlowly Cooled SlagSpinel - magnetite - zinc melitite (hardystonite) willemite - olivine -lead silicate - metallic lead - lead sulphide - copper sulphide - copper arsenide - nickel arsenide.ConclusionsIllustrationsINTRODUCTIONThis paper presents the results of a mineragraphic examination of representative samples of granulated lead blast furnace slags from the Port Pirie Smelter, and of slowly cooled samples of t:b.e same slags, undertaken at the request of the Broken Hill Associated Smelters Pty. Ltd., as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.THE SLAG SAMPLESThe chemical composition of the slags examined is given by the following three analyses of the granulated slags, supplied by the Broken Hill Associated Smelters (Table 1).

Jan 1, 1949

By Gillies A. D S, Just G. D

The advancement of computer applications in the coal industry is focusing interest on the presentation of washability data by mathematical functions.The normal method of presenting washability data is in the form of five curves, usually filled by eye or by cubic spline functions. It has been shown that coal washability can be characterised by two basic relations: the instantaneous ash vs relative density relationship and the instantaneous yield vs relative density relationship. In a new approach to the mathematical modelling of the instantaneous ash vs relative density relationship, theapplication of the algorithm to a data set from a mine in central Queensland was successful.

Jan 1, 1991

Feasibility is a value improvement process for projects. At any stage in project development, a feasibility study can be undertaken, but although the scope generally remains unchanged the extent of detail and level of accuracy usually increases with time. The main scope elements are a business definition, project description and an execution plan. The studies are designed to assess the potential of the project and to secure funding for on-going examination. Invariably, the investigations loop back to earlier stages to establish more appropriate development criteria but a critical stage is reached when a project construction decision is requested. This feasibility study requires very detailed presentation and analysis to a higher accuracy for the owner(s) and their potential lender(s).

Jan 1, 1997

By Cresswell G. M

The international coal industry is becoming increasingly aware of the economic impact of coal dewatering in terms of plant yield limitations, attainment of product specifications and freight costs. This paper examines the current position of dewatering within coal process plant design and reviews equipment developments over the past decade.

Jan 1, 1993

By B S. S Rao, S Chandra

IndiaÆs iron ore mining industry is growing rapidly in order to augment the capacity to meet the unprecedented demand for the iron ore. Traditionally, much of Indian iron ore production came from exploitation of high-grade haematite ores, with the exception of Kudremukh which beneficiates lean grade Banded Magnetite Quartz ore. Now with the changed scenario of demand and supply, keeping long term sustainability in mind, it is imperative to develop suitable processing technology for exploitation of banded haematite quartz (BHQ) ore available abundantly and not utilised so far. In this direction detailed characterisation and beneficiation studies were conducted with BHQ iron ore from the Bellary-Hospet region of India, assaying 36.5 per cent Fe. The mineralogical studies with the image analyser system revealed the presence of maghemite and haematite as iron-bearing minerals. The gangue mineral associations were siliceous, ferro-magnesian and carbonate minerals. Higher degrees of liberation were observed in the size range of 75 - 212 microns. Liberation grind tests were performed by grinding the ore to different top sizes in a closed circuit laboratory ball mill with the ground samples subjected to Davis tube tests. The yield, grade and recovery were used as parameters to plan a two-stage wet drum magnetic separation based on grinding the primary magnetic concentrate. After subjecting the final magnetic concentrate to flotation to remove residual silica a concentrate assaying more than 68 per cent was obtained. The non-magnetic product from the primary magnetic separation was deslimed, ground, blended with secondary magnetic tails and was subjected to a two pass wet high intensity magnetic separation (WHIMS). The WHIMS concentrate was further subjected to two-stage flotation to remove residual silica to obtain concentrates assaying 64 - 66 per cent Fe. The final combined concentrate from wet drum magnet and WHIMS after flotation could yield a blast furnace (BF) grade pellet feed concentrate assaying more than 65 per cent Fe with a yield about 39 per cent and iron recovery about 70 per cent. A direct reduction (DR) grade pellet feed concentrate assaying 67 per cent Fe with a yield of about 28 - 31 per cent and iron recovery about 53 - 57 per cent could also be produced. Based on the test work, a process flow sheet was developed to beneficiate the BHQ ore for production of BF/DR grade pellet feed concentrate. In this paper methodology adopted for selection of individual process, various diagnostic tests performed to rule out other beneficiation processes and the final process flow sheet development is presented and discussed in detail.

Jan 1, 2007

By Henley R, Harris L

High resolution airborne magnetic and radiometric data have been shown to optimize exploration for epithermal gold deposits in the vicinity of Charters Towers, northeastern Queensland. The radiometric data allow extrapolation of poorly outcropping geology to provide a cost-effective mapping technique, even at exploration scales (eg. 1:25,000). At a regional scale (eg. 1:100,000) the magnetic data reflect the regional tectonics and divide the area into domains for the application of different genetic models. For example: 1. the Ravenswood Batholith is characterized by multiple intrusions dating from Ordovician to Permian age. The polarity of the magnetic anomalies implies an age for the intrusions and indicates a deposit style for exploration. 2. extensional and wrench tectonics along the northern margin of the Drummond Basin are interpreted from the magnetic data and indicate favourable blocks for detailed exploration. Genetic exploration models may be tested in favourable environments by the recognition of geophysical signatures. These signatures reflect structural, lithological and alteration patterns arising from controls on ore deposits and can be applied at regional or detailed scales.

Jan 1, 1989

By J Zanganeh, M Ajrash, B Moghtaderi

Application of thermal oxidation is considered a promising technique in reducing fugitive methane gas from ventilation air methane (VAM). A typical thermal oxidiser operates with diluted methane and converts it to less potent greenhouse gases. However, having a thermal oxidiser in the vicinity of the coalmine exhaust shaft is a major safety concern as its high operation temperature increases the likelihood of accidental fire and explosion. The aim of this study is to investigate the application and effectiveness of side venting technique in reduction of deflagration consequences caused by methane gas. To address this importance a series of experiments were conducted on a detonation tube designed and fabricated as part of larger scale VAM Abatement safety project. The experimental work was carried out into two stages: examine the flame and explosion properties in a large-scale detonation tube to get reliable data; and then design and employ a venting system into the detonation tube to verify the effectiveness and performance of the venting against the flame and explosion.Results corresponding to this study show that the side vent duct with venting coefficient magnitude of 37 had a significant influence on methane flame deflagration and the explosion characteristics. The maximum pressure rise at the detonation tube reduced approximately 20 per cent to 32 per cent by applying the side venting duct. Also, the data shows that the venting damped the pressure oscillation after the flame deflagration which eventually reduced the system instability. Finally, by applying the venting technique the expected level of damage due to the dynamic pressure reduced to the level of limited building damage.CITATION:Ajrash, M, Zanganeh, J and Moghtaderi, B, 2017. Application of side venting technique in mitigation of methane – air explosion and flame deflagration in ventilation air methane, in Proceedings Australian Mine Vent Conference 2017, pp 153–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017