Search Documents

By D Craw

The Hyde Macraes Shear Zone is a mineralised low-angle shear within the Otago Schist traceable for ~30 km with a NW strike. It is been actively mined along 12km of this strike, producing >6 Moz of gold. The shear zone consists of greenschist facies rocks with a mineralogy only subtly different from that of the host schist. Pervasive fluid flow has occurred along grain boundaries and within microshears which have been enhanced by the deposition of hydrothermal graphite. We model the development of these microshears using a threedimensional numerical code. For an inhomogeneous initial rock with lithostatic fluid pressures and a dynamic permeability deformed under dextral non-coaxial flow, deformation is distributed into weak shear bands. Graphite deposition and associated reaction-softening has a dramatic effect on the development of model shear zones. Graphite is deposited into a shear band, weakening it and further localising the deformation into that shear band, producing an anastomosing and interconnected shear zone structure such as observed in the HMSZ. The degree of graphite precipitation and graphitic-induced weakening are varied in the models. More graphite precipitation with a low degree of reaction-softening results in more diffuse shear bands. In contrast less graphite deposition but with a high degree of reaction-softening more leads to the development of more focused shear bands. Graphite deposition has clearly controlled the formation of the HMSZ structure, and is an important indicator of potentially mineralised structures elsewhere.

Jan 1, 2007

By M J. Kelleher

CREAM is an acronym for coal recovery, evaluation, analysis and management and is a business improvement project at BMAÆs Goonyella Riverside mine that is focussed on maximising coal recovered. In August 2003, Goonyella Riverside was set a challenge to quantify coal loss and dilution and their relationship to cost, revenue and ultimately profit. While the mine was confident in its site forecasts of recovery (and loss), it was clear that the traditional measurement and analysis systems were inadequate to firstly, identify key loss areas and mechanisms and secondly, successfully quantify the benefit of various coal recovery initiatives. The path that BMA Goonyella Riverside has travelled to maximise coal recovered can be divided into four key steps: Mapping the process û This step involved the development of a coal flow process map for Goonyella Riverside that stepped through each component of the process from the coal reserve to the customer and identified key measurement points for the purposes of reconciliation. Understanding coal loss and identifying opportunities û This step involved conducting two detailed Reserve to Customer projects at the mine site to track a block of coal from the reserve to the customer and to gain a greater understanding of the relationship of dilution, coal loss mechanisms, revenue and costs associated with recovering additional coal. Coal data systems development û Two important coal data systems have been developed and implemented at Goonyella Riverside in the past twelve months, namely SnowdenÆs Coal Reconcilor and SeamFix. These systems enable coal losses and dilution to be quantified and reconciled back to the initial coal reserve. Implementation of loss reduction initiatives û This step involved the formation of a business improvement project referred to as æCREAMÆ in August 2004, for the purposes of improving pit coal recovery and maximising business value. To date a series of coal recovery trials have been run in a number of pits at Goonyella Riverside that have yielded significant improvements in business value. The key to the success of this project has been the discipline to follow a defined process map, management commitment through resourcing and shared key performance indicators, a successful acceptance strategy resulting in holistic ownership and the implementation of sustainable reconciliation systems. Coal loss and dilution are now quantifiable and their relationship to cost, revenue and ultimately profit is well understood. This paper discusses the process that Goonyella Riverside has adopted to maximise coal recovered.

Jan 1, 2005

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

By R-H Yoon

Increasing the upper particle size limit of flotation would allow operators to increase mill throughput, save operating costs, simplify flow sheets, and increase rate of return. However, coarse particle flotation is difficult for various reasons, of which bubble-particle detachment has been identified as the major limiting factor. In the present work, the process of bubble-particle detachment has been studied by directly measuring the forces required to detach air bubbles from hydrophobic solids. The measurements were conducted using a hanging balance apparatus. The measured forces were converted to detachment energies that can be compared with the work of adhesion, which in turn is a function of hydrophobicity, surface tension and contact area. The results were converted to detachment energies using the Young-Laplace equation for capillarity. In the present work, the solid surfaces were hydrophobised by coating them with octadecyltrichlorosilane and cetyltrimethylammonium bromide. The results show that bubble-particle detachment occurs in two steps. In the first step, air bubbles are deformed, while the three-phase contact (TPC) line is pinned, until contact angle reaches advancing angle. In the second step, the TPC line moves along the surface until solid/air interface is replaced by solid-liquid interface. In general, the energies of detachment measured in the second step are in good agreement with calculated work of adhesion. Thus, the energy required during the first step effectively represents an energy barrier for bubble-particle detachment. It has been found that the energy barrier varies with surface roughness and surface tension. The results of the present investigation suggest, therefore, that coarse particle flotation can be improved by control of particle hydrophobicity, surface roughness, and surface tension.

Jan 1, 2005

Metsim is proving to be a powerful tool when designing a heap leach operation. The most useful outputs arc determining the fluctuations in pregnant solution recovery rate, make-up water rate, gold recovery rate. and pond levels. Detailed data are needed for input: a pad loading schedule, a mining rate schedule for each ore type, column leach test data for each ore type, column tests on water dynamics (ie hourly flow-out versus-in during saturation and drain-down), monthly rainfall and evaporation data, and proposed pond dimensions. These data allow 'what if' studies on application rates, leach rates, loading rates and other variables of interest. Examples will he given of modelling both a rectangular pad and a valley fill operation.

Jan 1, 1994

By Reid A. F

Since early 1971 Western Titanium N.L. has been operating an ilmenite upgrading plant on a commercial basis at Capel, Western Australia. In their process ilmenite is pre- oxidized, then reduced in a rotary kiln to a mixture of metallic iron and titanium oxides. The iron is leached out by accelerated rusting in aerated water, leaving a product with titanium content, expressed as Ti02, of about 92%. Samples from different stages of the up- grading process, representing operations over the last two years, have been studied in detail by X-ray diffraction methods, and the sequences of phases and reactions occurring have been determined. Quantitative X-ray studies showed the ilmenite feed materials to consist of a mixture of ilmenite and pseudo- rutile. Pre-oxidation of the ilmenite at =1000¦C leads to the formation of rutile plus a Fe2TiO5-FeTi205-Mn2TiO5 solid solution. The final reduction product consisted of a mixture of metallic iron, reduced rutile and a FeTi05-MnTi205-Ti305 solid solution. The relative amounts of these reduction products were very sensitive to the initial concentra- tions of the minor constituents manganese and magnesium. The effects of variation of ilmenite feed rate, reducing atmosphere,- reduction temperature and controlled addition of magnesium were also studied.

Jan 1, 1973

The lignite mines in the Latrobe Valley of Victoria/Australia have been using continuously operating mining systems for more than 50 years. The relatively small bucket chain dredgers of the early years have been progressively displaced by bucket wheel dredgers with increasing size, increasing capacity and increasing service weight. The large machines for the new open pit Loy Yang have a bucket wheel outreach of 46m, an effective capacity of 3350 bm' coal/h respective 2500 bm' overburden/h and a serv- ice weight of approx. 4500 t. The time between signing of con- tract and starting of operation for these machines is at least four years. The high service weight, the resulting high capital invest- ment and the long period for design, design review, manufac- turing, erection and commissioning of these machines directed the SECV to investigate a possible application of compact dredgers for the Latrobe Valley.

Jan 1, 1989

By Taylor L. M

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry. Some of the computer programs previously used to predict rock motion employed polygonal elements with comers and sides to model the rock (Cundall, 1971; Walton, 1982; Taylor, 1983). This approach allows the elements to bulk because of the corners and the aspect ratio. However, tracking the many interactions of the comers and sides of the elements is a computationally intensive process. Several other rock motion computer programs were developed that employed spherical elements, (Schamaun, 1984; Gorham-Bergeron et al, 1987) but they lacked correct bulking mechanisms or could not be vectorized for efficient execution on vector processing machines. A new spherical element code called DMC (Distinct Motion Code) (Taylor and Preece, 1989a, 1989b) has been developed this past year. DMC was designed and written to take advantage of super-computer vector processing capabilities. The efficiency has also been increased through the use of spherical elements, explicit time integration and a new contact search algorithm. When spherical elements were chosen for efficiency, some physically correct mechanisms for capturing the bulking behavior of the rock mass also had to he developed. This paper will treat several mechanisms that were developed to allow spherical elements to exhibit correct hulking behavior.

Jan 1, 1990

According to our experimental results, the following oxygen probe recommended, that is, the magnesia stabilized zirconia was employed as a solid electrolyte and Fe.FexO solid elect- rode was used as a reference electrode. Using such an oxygen probe, we tried to measure the oxygen potentials in molten metals, mattes and gases in the following fields of non-ferrous metal industry, molten copper in the side launder before casting, molten crude lead in the forehearth of ISP blast furnace, molten copper mattes in the forehearth of blast furnace and in the settler of flash smelting furnace, gas in the settler of copper flash smelting furnace and flue gas in the electric furnace for ferro-silicon. In the past ten years or so, many experi- mental results in the field of fundamental studies have confirmed that the equilibrium oxygen potential could be measured conveniently and accurately by an electrochemical method using a zirconia solid electrolyte. Recently, such an electrochemical technique has been also applied to a device for physicochemical invest- igation or process control in the non-ferrous metal industry. Such a device consists of an oxygen con- centration cell with stabilized zirconia, and it is commonly called an "oxygen probe" or "oxygen sensor".

Jan 1, 1980

By Dance A

Highland Valley Copper recently implemented a system of measuring run-of-mine (ROM) ore properties and monitoring their effect on both mine and mill performance. These properties are principally ore hardness and size. For some years, Highland

Jan 1, 1998

By D Craw

Quaternary warping and uplift of antiformal schist ranges in Central Otago, New Zealand, has resulted in recycling of alluvial gold from widespread, generally weakly auriferous, Miocene fluvial gravels that unconformably overlie the schist, into aprons of fan sediments along the range margins. Basement erosion during uplift has been limited and so gold input from sparse gold-bearing quartz veins in the schist has been relatively minor. In an eluvial cycle on the slopes of the ranges, chemical remobilization of gold occurs during oxidation and erosion of the Miocene sediments. The typically fine-grained (300 - 400 ¦m) gold undergoes chemical modification and grain size enhancement of up to two orders of magnitude, and much of it is redeposited in a large number of relatively small alluvial fans along the range margins. Groundwater mobility within the fans results in minor additional gold mobility and grain size enhancement. During range uplift, a small number of relatively large axial streams and rivers have developed in structural lows between growing antiformal folds. Axial streams 'gather' their flow from consequent streams draining the folds, and flow parallel to a range axis for some distance before cutting across it in an antecedent gorge. The axial streams rework alluvial fan sediments along the range margins, and transport mainly fine-grained gold from the fans along the ranges. This gold is redeposited where the axial streams emerge from a range in the neighbouring structural basin. Axial streams drain relatively large areas of range surface, and thus reconcentrate significant quantities of gold in a small number of relatively large fans and fluvial deposits. The processes of gold collection and re-deposition by axial streams are essentially the same, regardless of stream size. Coarse-grained gold produced by chemical remobilization, is more difficult to transport in fluvial systems, and thus remains in close proximity to eluvial environment where it was formed.

Jan 1, 1995

The paper describes the reasons for the development and for the selection of systems which were finally adopted; further estima- tion and design engineering problems, as well as experience with large screens in operation. Advantages, disadvantages and the final li- mits of screen dimensions are indicated.

Jan 1, 1984

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

The late Carboniferous to early Permian Featherbed Volcanics cover an area of about 3000km near the western margin of the Hodgkinson Basin, in northeastern Queensland. The dominantly ignimbritic volcanic rocks are mostly confined to a single, composite, volcano-tectonic depression, but, along with the associated intrusive rocks, may be divided into two main groups: late Carboniferous I- type rocks and early Permian A-type rocks. Late Carboniferous I-type andesitic to rhyolitic ignimbrites and minor andesite lava crop out in the southeastern, southern, and southwestern parts of the complex, mostly confined to a basin-like depression, or "sag" structure, and are associated with coeval dioritic (and rare gabbroic) to granitic intrusive rocks. Extensive Sn, W and base- metal, and some Au, mineralisation are associated with these rocks, particularly in the southeast. The main part of the complex is of early Permian age, and consists almost entirely of A-type rhyolitic ignimbrite and relatively minor volumes of lava intruded by a peripheral ring dyke of porphyritic microgranite and by resurgent-type plutons of porphyritic microgranite and microgranodiorite. These rocks are associated with sparse base-metal, Au, U, W, and Sn mineralisation.

Jan 1, 1987

The carbonatite-hosted apatite deposit at the Cajati open pit mine in the Jacupiranga igneous-carbonatite complex is located in south-eastern Brazil. The major styles of apatite mineralisation include veins or veinlets, small pods or patches, disseminated apatite and locally massive aggregates. The metallurgical concentration of the apatite is accomplished by grinding the carbonatite, removal of magnetite with a magnetic drum, size classification with cyclones and flotation to suppress carbonates and collect apatite. To examine the character of the apatite grains and to apply those observations to apatite beneficiation, specimens of carbonatite were collected from recent exposures in the mine and from selected drill holes. This study utilised a variety of microscopy methods, including transmitted and reflected light, cathodoluminescence (CL) and scanning electron microscopy with wavelength-dispersive spectrometers for mineral compositions. It was found that LREE, Na and Sr are the main elements replacing Ca in the apatite, with relatively low oxide contents (<0.5 per cent, but up to about one per cent for Sr). LREE and Sr contents consistently increase in the latest intrusions (C4, C5 and SP24). Chemical and morphological modifications of apatite were recognised to be related to detrimental effects on flotation recovery. Three examples illustrate this relationship: 1.  Apatite with reddish CL is fractured. Locally that apatite exhibits no CL due to CL quenching caused by iron entering the apatite structure.2.  Apatite from the xenolith-rich area exhibits abundant fine, platy silicates that appear to interfere with flotation and lower apatite recovery.3.  So called æhardÆ apatite, which is more difficult to grind, occurs in an area in the mine that was affected by hydrothermal activity. That activity is evidenced by the development of a bright, white CL rim in the apatite, and by the presence of late veins of carbonates and sulfides that fill fractures and appear to contribute to higher cohesiveness of those apatite grains.

Jan 1, 2008

Rock formation at shallow depths is generally associated with complex geology consisting of many joints, fractures, bedding planes, etc. Fragmentation results from primary blasts in such strata are therefore significantly influenced by structural discontinuities. To evaluate the role of discontinuities, which is of great use in the design of blasts in such conditions, a two-stage investigation program was taken up. In the first stage, model scale tests were conducted with single and double holes with the strike of discontinuities parallel and perpendicular to the face. Later, field studies were conducted in a limestone mine and a coal mine. Blast patterns were modified based on the results obtained from model scale blasts. Secondary blasting was taken as a measure to assess blast performance in the field, whereas mean fragment size, fine and coarse fragmentation indices were considered as fragmentation measures in model scale tests. Model tests indicated confinement of explosive energy by the discontinuities surrounding blasthole. Crater shape and size were significantly influenced by the orientation of joints with respect to the face. Modified blast designs with decreased burden x spacing patterns resulted in improved fragmentation in the field. A reduction of about 12 per cent in explosive consumption was recorded with modified blast designs. Boulder formation was observed to decrease by about 79 per cent as well.

Jan 1, 1995

By J Manuel, R Muddle

The demand for iron ore has increased significantly in recent years, with new iron ore sources being mined to meet this demand. As the composition of sinter blends changes with the availability and cost of iron ore, so too does interest in the impact of new ore types on granulation and ultimately productivity. This paper describes a study into granulating characteristics of seven iron ore types, including various hematite and goethite ores. The effect of ore type on feed moisture requirements, green bed permeability, green bed strength and granule size distribution was examined for single ore blends containing coke, flux and returns. The ore size distribution was varied in these blends and its effect on granulating characteristics examined. It was found that the optimum moisture requirement of the ore was more dependent on ore type than ore size distribution, but ore size distribution (and specifically intermediate particle loading) had a greater effect on green bed permeability. The saturation moisture value for an ore was found useful in predicting both optimum granulation moisture and green bed permeability.

Jan 1, 2005

By J Williams

The recent drought has highlighted the finite nature of AustraliaÆs divertible water resources. According to AustraliaÆs recently completed National Land and Water Resources Audit, development of water resources in southern Australia has reached or exceeded sustainable extraction limits. Similarly, 161 out of 538 groundwater management units are either totally allocated or already over allocated. Whilst mining only uses about three per cent of diverted water resources, water scarcity may be a major factor that determines whether potential mines can be developed in the future. Furthermore, the development of extraction and processing facilities that limit water use and maximise the re-use the waste water streams will be even more fundamental features of the mining industry in the 21st century than they are at present. There are encouraging examples where innovative water re-use technologies are significantly reducing the water used per unit of mined product. Whilst mining in the areas of Australia draining to the tropical seas may be less constrained by a current lack of water (60 per cent of divertible water resources drain into the Timor Sea, Gulf of Carpentaria and north east Coral Sea), it is highly probable that there will be increasing demand for these waters from the irrigation industry, whilst pressure will also be applied to ensure that environmental flows that benefit the coastal fishing and prawn industries are maintained. In the Great Artesian Basin, current research is demonstrating that the groundwaters are being recharged at rates considerably lower than current extraction. Whilst some other groundwater basins in arid and semi-arid Australia have currently untapped resources, these water are often relatively saline and/or may be intimately linked with key ecosystems in discharge areas. This paper presents an overview of the current state of our water resources and examines some of the key water use issues including allocation, use and reuse, environmental flows and competing demands on the resource that will ensure that water issues remain high on the policy agenda for mining, irrigation and other water users.

Jan 1, 2003

By S Shipard

Filters are used in water treatment and hydrometallurgical process plants for objectives such as generating a dry spadable solid, pumpable high density slurry or high purity filtrate. The priority objective of every polishing filter, sometimes also termed clarifying filters is high purity filtrate and these are found in many diverse industries and even different applications within the same industry.To generate a high purity filtrate, process designers have the choice of many different polishing filter products, but in reality very few polishing filters are based on fundamentally different filtering concepts.This paper reviews the technology merits of well-known and the more recently developed polishing filter products and aims to assist metallurgists and engineers with the selection of an appropriate polishing filtration technology for pregnant liquor filtration and other process applications, plus a guide to best practice.CITATION:Shipard, S, 2013. Polishing filters for mineral processing plants, in Proceedings MetPlant 2013 , pp 118-125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

The MIMDAS geophysical data acquisition system developed and tested by the former MIM Exploration Pty Ltd (MIMEX) is now commercially available worldwide through Geophysical Resources and Services Pty Ltd (GRS). The system implements several new features in its design that give it significant advantages over conventional systems and allows for new approaches to electrical exploration. In particular, the achievable signal to noise levels permit exploration to depths once thought beyond the range of electrical exploration. The flexible multi-channel configuration lends itself to truly 3D surveys in the style of modern seismic techniques. Each of these aspects is illustrated with a number of case histories from both Australia and South America.

Jan 1, 2004