Search Documents

By C Zhang, I Canbulat, S Saydam, H Yu, H Chen

Natural rocks are frequently exposed to groundwater and complex geological conditions. Environments with water presence are more susceptible to chemical corrosion, which notably affects rock’s micro properties. Generally, the pH of acid mine drainage in hard rock mines can be low to 5, and the pH of quarrying waste deposits can be below 3. With the expanding scope of mining engineering in aquifers and salty areas, chemical corrosion can also caused by different types and concentrations of anions. The anions can significantly affect rock’s mechanical properties. Therefore, it is critical to emphasise the impact of anion and acid on the mechanical and micro characteristics of rock. This paper commences with an introduction to representative corrosive environments. Then the UCS tests are conducted on granite samples corroded by chloride ions and sulfate ions. Anion has negative effects on the strength of granite. The reason is that certain minerals can react and be dissolved by anions and hydrogen ions, such as Al2O3. Furthermore, the scanning electron microscope (SEM) shows that the roughness of the fracture surface increases with the anion concentration. The effect of acid is notably more pronounced than anion on the micro properties of granite. The initiated fissures and pores also increase with the concentration of SO42- and Cl- ions, which is the micro explanation for the impact of anion on rock strength and stability. Subsequently, the permeability of the granite specimens is tested. The reason that granite performs insensitivity to acid and anion is attributed to its low permeability and high content of inactive oxides, such as quartz. To summarise, anionic and acidic conditions can slightly deteriorate the mechanical and micro properties of granite. While SO42- demonstrates a higher level of corrosiveness on granite than Cl-.

Sep 1, 2024

By S Carr-Cornish, K Moffat

Social licence to operate is developed and kept through managing both operational impacts and the relationship between local community and company. However, CSIRO research has demonstrated that in determining how accepting community members are of a mining operation, relational factors, such as procedural fairness and trust, are much more important than operational impacts, such as impacts on employment and the environment (Moffat and Zhang, 2015). Companies seek to develop relational factors through their engagement with local community; such engagement has many aspects, including, initially identifying stakeholders and positioning the company as part of the local community (Lacey et al, in prep; Thomson and Boutlier, 2011). These relational factors involve the social identities of people living in the community. Social identities are a part of people that shape their beliefs, based on their connections with various groups in their lives (Hogg et al, 2004).An engagement process, intentionally or not, inevitably interacts with the social identities of stakeholders (Crane and Ruebottom, 2011). For example, traditionally, at the very beginning of engagement processes, community members are assigned to categories using conventional stakeholder mapping and categorisation methods, often based on assumptions about stakeholders’ interests, which equates to assumptions about stakeholders’ social identities (Colvin, Witt and Lacey, 2016; International Council on Mining and Metals, 2012). Yet, there has been limited empirical inquiry into whether such categories reflect the social identities of stakeholders and if there is a bearing on relational factors, including, the perceived fairness of consultations and trust in mining companies (Crane and Ruebottom, 2011). Also at this time, companies commonly seek to create a presence in communities, for example, joining Chambers of Commerce and participating alongside community members. Again, there has been limited empirical inquiry into whether community members and companies identifying with the same overarching group and thus sharing aspects of social identity, influences relational factors (Crane and Ruebottom, 2011). In this study, we examined the effects of changing aspects of social identity by changing how stakeholders were identified and companies were positioned, on how stakeholders’ perceived a new mining operation, specifically how they perceived the procedural fairness of the proposed consultation process and trusted the company, two factors that underlie a company’s social licence to operate.CITATION:Carr-Cornish, S and Moffat, K, 2016. Out of the box – the power of social identities in engagement processes, in Proceedings Life-of-Mine 2016 Conference, pp 180–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By S L. Simpson, J Waworuntu, B M. Angel

"The Batu Hijau copper/gold mine, operated by PT Newmont Nusa Tenggara, is located in the south-western part of Sumbawa Island, Indonesia, and is situated ~10 km from the south coast at an altitude of ~450 m above sea level. The mine became fully operational by year 2000 and processes approximately 120 000 t of ore per day that contain an average of 0.53 per cent copper and 0.4 per tonne (g/t) gold. Tailings management at the mine includes a deep-sea tailings placement (DSTP) system that discharges tailings through a pipeline via an outfall located at a depth of 125 m at the head of the submarine Senunu Canyon (Figure 1).The environmental impact assessment undertaken prior to approval of the DSTP evaluated both on-land tailings storage facility (TSF) and DSTP options for tailings management. Negative attributes of the on-land TSF included removal of approximately 2300 ha of forest/agricultural land, the potential relocation of >2000 people from their communities, the high average annual rainfall (>2500 mm) and potential for earthquakes presenting challenges for water management and creating a long-term risk of failure. The final choice and Indonesian Government’s approval of DSTP was also influenced by the close proximity of the deep submarine canyon to the mine. The Batu Hijau mine is one of the larger examples of DSTP in the world and deposits tailings at the greatest depth. The depth of the main canyon increases to >2000 m within 20 km of the coast, and to >3000 m approximately 50 km from the coast.The DTSP at Batu Hijau must comply with an environment management plan (EMP) and environment monitoring plan of permit stipulation that approved its commencement in 2000; updated in 2010 and 2015. The environmental management objectives were to avoid impacts to highly productive components of the ecosystem such as coral reefs, mangroves, surface waters and fisheries, and confinement of impacts to areas of low biological productivity. In the vicinity of the DSTP outfall and within the Senunu Canyon, the management plan predicted significant adverse impacts from the DSTP on the marine ecosystem in the form of: reduction in sea water quality due to elevated turbidity and dissolved copper concentrations burial of benthic organisms a reduced habitat for demersal fish.Recovery of the pelagic and benthic ecosystem to preoperating conditions was predicted to occur within the first two years after operations cease. The CSIRO has performed due diligence studies to independently verify compliance with permits and evaluate new monitoring objectives (Apte et al, 2004; Simpson et al, 2010; Angel et al, 2015), and has performed assessments of environmental monitoring data on the tailings footprint and ore stockpile processing against the above environmental objectives (Simpson and Angel, 2015).CITATION:Angel, B M, Simpson, S L and Waworuntu, J, 2016. Long-term monitoring and targeted assessments to improve management of mine wastes – the Batu Hijau project, in Proceedings Life-of-Mine 2016 Conference, pp 81–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By K Li, C Zhang, i, J Oh, S Saydam, H L. Ram

Rock surface roughness plays an important role in excavation engineering projects and applications related to surface support structures, such as shotcrete and thin-sprayed liner (TSL). The morphology of the substrate affects the mechanical behaviour at the interface significantly. Therefore, it is necessary to quantify the roughness to investigate the relationship between roughness and mechanical properties. The joint roughness coefficient (JRC) proposed by Barton and Choubey (1977) is widely used in practice. It initially estimated the roughness by comparing it to 10 standard profiles visually. However, this method has lots of limitations, it is not only subjective but also a two-dimensional parameter with a small lab scale (Beer, 2002). The subsequent research on JRC, from visual comparison with Barton’s standard profiles to measuring the roughness with a profilometer (Weissbach, 1978; Alameda-Hernández et al, 2014). Then, 2D profiles or 3D surfaces by different technologies with higher resolution and accuracy, such as 3D laser or optical scanners (Fardin, 2004; Jiang, 2020, 2021). These 3D scanners are expensive and only suitable for laboratory scales. LiDAR scanners (Lato, 2009; Aubertin, 2022) have been applied in industrial size, but it is difficult to achieve a millimetre-level accuracy, which is mostly used to detect the thickness of shotcrete in practice. Thus, finding a cost-effective surface roughness measurement method with high accuracy is necessary. Photogrammetry is another method to digitalise the roughness of the surface. Similar to 3D scanners, photogrammetry also generates the point cloud of the objective surface and then reconstructs the 3D model of the objects. 3D reconstruction technology is a trendy technology in recent years. The structure from motion (SfM) algorithm (Westoby, 2012) to rebuild the 3D model with a flexible workflow, aligning photos, building dense point cloud, mesh and texture, which has been proved that can rebuild an accurate model in variable fields.

Nov 29, 2022

The theme of the conference this year is diversification. One way to diversify is through acquisition. The principle underlying the winner's curse is that in competitive bidding situations where the value of the asset bid for is uncertain the winning bid will overstate the true value of the asset. The successful bidder is blessed with the winner's curse. What this paper will explore is to what extent this is true; how acquirers can avoid being blessed with the winners curse; and show how joint venture deal structures are used within the mining industry to avoid the winners curse.

Jan 1, 1996

By S Nowosad, O Langefeld

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

By P Kappen, R N. Collins, K M. Spiers

X-ray absorption spectroscopy (XAS) is a synchrotron-only technique used to determine chemical speciation, providing a powerful alternative to most traditional ‘wet chemistry’ and lab-based speciation methods. XAS is an element specific method that can be used to address a variety of systems, ranging from heterogeneous to homogeneous, polycrystalline to amorphous, and solid to liquid. The strength of XAS in identifying and managing chemical species in tailings and mine waste is demonstrated, with the presentation of highly relevant studies into lead, uranium, chromium and arsenic speciation. In each example, waste samples are compared with known standards, allowing an assessment to be made of the quantity of particular chemical species in each.CITATION:Spiers, K M, Collins, R N and Kappen, P, 2015. ‘Forget the wet chemistry’ – how the Australian Synchrotron can help with tailings and mine waste management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Sasaoka, H Shimada

Mined-out limestone/aggregate quarries in Japan contain many high and enormous pit walls. Many precious resources are abandoned in these final pit walls. In addition, there are many mines which are located in or near populated areas in Japan. Utilisationof the potentially useful under- ground space at mined-out sites is a topic relevant to the practice of surface mining. This paper describes and discusses the concept of underground space utilisation and tunnelling systems, referring specifically to geotechnical/ tunnelling parameters.

Jan 1, 2008

By A Sinuhaji, R Poedjono, G Flumerfelt

PT Freeport Indonesia is currently building the DOZ mine. It is a 25 000 tonne/day block caving operation which is scheduled to reach designed production levels by the fourth quarter of 2002. This paper describes some of the issues and challenges faced by the operation when introducing a new undercut method part way through the project. Advantages and disadvantages are discussed as well as the expected benefits of the new method.

Jan 1, 2002

By M Grigorescu, J H. Hodgkinson

The expansive, open cut iron-ore mines in Western Australia typically experience few days of rain per annum, often amounting to less than 250 mm. Unlike mines where rainfall is frequent, they may be less prepared for extreme rainfall events. Such events can cause erosion, flooding and sedimentation, drainage alteration, spoil and stock heaps wetting and effect slope stability. Such impacts may threaten personnel safety, infrastructure, and production. The CRATER (‘Climate Related Adaptation from Terrain Evaluation Results’) framework collates and interprets a mine’s pre-existing data and semi-quantitative information to assess vulnerability to, and ultimately plan to avoid or minimise, flood-related hazard to infrastructure, people, downtime, environment and revenue. Outputs assist decision makers to design investment strategies for minimising mining operations’ vulnerability to climate. Previously developed for smaller, wetter mines in Queensland’s coal region, the outputs provide a hot-spot map, fault tree analysis and an assessment of the mine’s capacity to adapt. The multicriteria evaluation (MCE) within a geographic information system (GIS), equally suits iron-ore mines’ siteconditions (elevation, slope, drainage, soil and vegetation) to identify critical inundation areas. Hotspot results provide target zones for in-depth fault-tree analysis that, in turn, present a range of sitespecific adaptation options. Rainfall-intensity and the number of rain days since the 1970s have increased over central and eastern parts of the Pilbara Region. While tropical cyclones may become less frequent, they are projected to increase in intensity. Although some parts of the Hamersley Ranges receive more than 500 mm per annum, rainfall in the Pilbara is generally very low. Therefore, experience of the impacts of extreme rainfall events in the constantly changing topography of Western Australia’s iron ore region may be sparse. Minimising potential effects can be proactively assisted using CRATER.

Nov 8, 2021

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

By K A Plumb

New structural studies in the Walker Fault Zone of eastern Arnhem Land are integrated with basin-wide reconnaissance observations, made to refine models for the structural evolution of the McArthur Basin and provide new insights into the nature of metal logenetical ly important pre-inversion phases of the basin's evolution. At least five principal events may be identified during the Proterozoic: The Tawallah Group and equivalents were deposited throughout the McArthur Basin during an extensional event. Rifting of an incipient Batten Trough occurred at this time, in a terrain characterised by orthogonal, linked extensional faults. Uplift and erosion of the Tawallah Group accompanied continuing extension and was penecontemporaneous with continuing deposition of the overlying Parsons Range Group, within a precursor to the Walker Trough. Dt (of the Walker Fault Zone) relates to a new rifting event, penecontemporaneous with deposition of the McArthur Group and its equivalents in the Walker and Batten Troughs. This rifting accompanied dextral strike-slip faulting along northerly-trending bounding faults, as a result of northwesterly-directed oblique extension, leading to pull-apart basins. D2 inversion of the Batten and Walker Fault Zones pre-dates deposition of the Roper Group. In the proposed model WNW-ESE directed shortening (D2.), accompanied by folding and thrusting, and by local development of cleavage in the Walker Fault Zone, is seen to be followed by northerly-trending sinistral faulting (D2b), about a SE to ESE-directed compression. D3 is basin-wide and post-dates the Roper Group. It is characterised by conjugate faulting and folding about ENE to NE-directed compression. The latest Proterozoic event to be identified (D4) comprises widespread north-trending strike-slip dextral faulting of Roper Group, coupled with N-S directed thrusting across the Urapunga Fault Zone and Murphy Inlier This is accompanied by late dextral reactivation of NNW to NNE-trending faults in the Walker and Batten Fault Zones.

Jan 1, 1994

By D McB Martin, A Piechocka, M Jessell, M Lindsay, E Ramanaidou

The Hamersley Basin of Western Australia, approximately 500 km long by 200 km wide, is recognised globally for its rich endowment of iron ore resources. Two types of bedded iron ore mineralisation are recognised: the Proterozoic hypogene martite-microplaty hematite ores; and the more recent Cenozoic supergene martite-goethite ores. Exploration strategies depend on the style of mineralisation being targeted; however, stratigraphy and structure are fundamental controls on both ore types. Therefore, the ability to visualise the 3D geology of the entire basin is critical for the understanding of iron ore occurrences and their relationship to ore genesis of bedded iron ore mineralisation. However, due to the large size of the basin, generating a 3D geological model of the regional stratigraphy and structure has not been possible, or prioritised, primarily due to software limitations. Recent advances in implicit automated geological modelling presents an ideal opportunity to develop a 3D model of the entire Hamersley Basin. The innovative Loop software was used to model open source geological data (ie geological mapping, outcrop orientation data, and fault data) sourced from the Geological Survey of Western Australia. In addition to generating a 3D geological model, information such as stratigraphic thickness and fault offset information was extracted using the map2loop module and demonstrated its application to exploration targeting. This study demonstrates how a basin-wide 3D geological model was used to conduct a regional structural analysis of the Hamersley Basin. The results of this study provide opportunities for other prospective regions to be rapidly modelled in order to enhance the understanding of the geology and improve exploration targeting.

Nov 8, 2021

By F Sandrone, J-P Dudt, J Zhao, E Paltrinieri

Tunnel boring machines (TBMs) excavation is nowadays more and more considered a valuable alternative to conventional tunnelling. As a matter of fact, thanks to its advantages such as greater rate of advance and safer working conditions, the application of TBMs has increased significantly in recent years. Despite the possible excellent performance of TBMs in favourable ground conditions, the advance rates could be significantly slowed down or even obstructed in limiting geological situations. This obviously traduces in potentially longer tunnel construction times and higher costs and, therefore, in a preference for conventional method. One of the major geological hazards encountered during tunnel construction, is related to the presence of fault zones or heavily jointed and fractured rocks. The most common geotechnical problems resulting from tunnelling in these difficult conditions include the instability of the excavation face, instabilities of side-walls producing large overbreaks on the tunnel profile, excessive deformations in case of squeezing grounds, frequently changing stresses in terms of magnitude and direction, high water inflows, etc. The decisions aids for tunnelling (DAT) is a model and a computer code that can be used to evaluate the influence of the uncertainties related to both the geological/geotechnical conditions and the construction process on final tunnel construction time and costs. In this framework, the DAT is used for assessing the effects that challenging ground conditions may have on tunnelling operations in terms of costs and delays. This is done by simulating the tunnel construction considering several geological profiles. The aim of the study is comparing different excavation methods (ie drill and blast versus TBM) in changing ground conditions along the tunnel alignment ranging from good rock, to very poor and fractured formations. The results show the impact, in terms of changing construction time and cost, of the excavation method versus the ground conditions.CITATION:Paltrinieri, E, Dudt, J-P, Sandrone, F and Zhao, J, 2014. Comparison of excavation methods in different ground conditions with the decision aids for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 573–580 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P Joyce, D R. Cooke

The Dinkidi Cu-Au porphyry deposit is situated in the Caraballo Range of North Luzon, Philippines. Although comparatively small, Dinkidi has unusually high gold grades with drilling by Climax-Arimco Mining Corporation delineating a 110 Mt orebody at 1.2 g/t gold and 0.5 per cent copper. The magmatic-hydrothermal evolution of Dinkidi records a distinctive switch in mineralisation from an early orthoclase-dominated Au-rich assemblage, typical of alkaline porphyry systems, to a later quartz stockwork Au-Cu rich assemblage typical of most calc-alkaline to shoshonitic porphyry systems. The early orthoclase-dominated stage is associated with the intrusion and crystallisation of a variably-textured clinopyroxene-syenite dyke that contains high-grade (5 - 20 g/t) gold mineralisation. We consider this dyke to be a Cu-Au porphyry analogue to the pegmatites found in granitic systems. Dinkidi is hosted within the Early Miocene Didipio Igneous Complex. This alkaline igneous complex is comprised of early unmineralised gabbros (pyroxene-plagioclase cumulates), clinopyroxenites (pyroxene cummulates), diorites and monzodiorites that have been intruded by a large, weakly mineralised monzonite pluton. The Dinkidi deposit is located at the southern margin of the monzonite pluton. Mineralisation is hosted within a composite monzonite stock. Within the stock, an 800 metres by ~200 metres (plan section) elongate monzonite stock (Tunja Monzonite) predates and hosts the bulk of the Au-Cu mineralisation. This has been intruded by the thin (10 to 30 m wide), highly mineralised variably-textured magnetite- and clinopyroxene- phyric syenite pegmatite (the Balut Dyke). The youngest phases of the composite stock are leucocratic quartz-monzonite porphyry (Quan Porphyry) that grades texturally, in its core, into a post-mineralisation crystal-crowded quartz-syenite (Bufu Felsite). The late-stage Bufu Felsite is inferred to be the source of much of the Cu-Au mineralisation. The Didipio Igneous Complex has intruded a sequence of Late Oligocene alkaline andesitic lavas and volcaniclastics and overlying potassic dacitic lavas. Whole rock geochemical analyses indicate that the intrusions and the potassic dacite lavas in the surrounding region are co-magmatic. Five main stages of hydrothermal activity are recorded at Dinkidi. An unmineralised K-silicate (biotite-magnetite) alteration assemblage formed during the intrusion of the Tunja Monzonite stock. The diorites surrounding the stock display intense selectively pervasive biotite and magnetite alteration and are cut by an extensive network of orthoclase veins and monzonite dykes. The orthoclase-dominated assemblages of Stage Two carry substantial high-grade Au mineralisation and are associated with the intrusion of the Balut Dyke. The emplacement of this unusual dyke is associated with emplacement of pegmatitic clinopyroxene-orthoclase-magnetite¦sulphide dykes, localised orthoclase flooding along the margins of the dyke, and subsequent emplacement of an extensive orthoclase-actinolite-bornite¦chalcopyrite-fluorite stock-work, and development of widespread selectively pervasive actinolite alteration. The main stage of Au-Cu mineralisation at Dinkidi is intimately associated with the intrusion and initial crystallisation of the leuco-monzonite porphyry (Quan Porphyry) and emplacement of a quartz stockwork followed by carbonate-sulphide deposition and intense vein-related sericite and carbonate alteration assemblages. The quartz stockwork formed synchronous with the deposition of the æBugoy QuartzoliteÆ, a very coarse grained mosaic of quartz-orthoclase-perthite along the walls and top of the crystallising intrusion. Stage 3 was terminated by crystallisation of the distinctively vuggy Bufu quartz-syenite phase in the core of the intrusive, with associated antiperthite veins, and the subsequent explosive brecciation of the roof of the intrusion, forming a quartz-fragment breccia from the Bugoy Quartzolite. Retrograde metasomatism during Stage Four was intimately associated with the emplacement of extensive, late-stage carbonate, silica and zeolite veins and widespread selectively pervasive carbonate alteration. The last hydrothermal stage at Dinkidi, Stage 5, is comprised of strong selectively pervasive clay alteration and is associated with fault-related brecciation of the Dinkidi stock.

Jan 1, 1999

By J D. Bryant

The Ernest Henry Copper-Gold mine, the third largest copper deposit in Australia, is located 35 km NE of Cloncurry in the Mt Isa-Cloncurry mineral district of NW Queensland. Ernest Henry Mining Pty Ltd (EHM), a wholly owned subsidiary of Xstrata Copper Australia, operates the mine. Approximately 10.2 Mt of ore grading 1.12 per cent Cu and 0.56 g/t Au were processed during the 2001 - 2002 financial year. The Ernest Henry plant produces copper-gold concentrate, which is trucked to Mt Isa for smelting. The Ernest Henry deposit is a member of the diverse Fe-oxide-(Cu-Au) class of deposits. The orebody is hosted within a sequence of moderately SSE-dipping, intensely altered Paleoproterozoic intermediate metavolcanic and metasedimentary rocks. Copper (chalcopyrite)-gold mineralisation occurs mainly within the magnetite-biotite-calcite ¦ pyrite matrix of a 250 m + 300 m pipe-like breccia body. The breccia pipe comprises two anastomosing lenses separated by a lower grade, clast-supported breccia zone. Several anastomosing brittle faults affect the macro-geometry of the orebody. Copper grade is proportional to the degree of matrix support in the breccia. The July 2002 Ore Reserve was 88.7 Mt @ 1.0 per cent Cu and 0.5 g/t Au. Resource estimation at Ernest Henry is based on a large database of predominantly diamond drill hole information. Drill spacing is typically 50 m + 50 m. Ordinary kriging is used to estimate Cu, Au, SG and IST (oxidation indicator) into model parent cells of dimension 20 m E + 20 m N + 16 m RL. The block model is comprised of five geological-geochemical domains represented by 3D wireframe surfaces. Zonal control, where samples and blocks are assigned the same domain number, is used to control grade estimation. The geometry of the domains defines hard grade boundaries across strike and soft boundaries along strike A Deep Drilling Project was initiated in August 2002 with the initial aim of testing the down-plunge extension of the orebody to a vertical depth of over 1 km. The encouraging intersections to date have resulted in a significant increase in the mineÆs open pit Mineral Resource together with the identification of an underground Mineral Resource. Added benefits of the project included an expanded and updated geological legend and an improved understanding of the host geological sequence.

Jan 1, 2003

By P Hollings, J Holliday

Porphyry copper, gold and molybdenum deposits form in subduction-related settings in association with calc-alkalic or alkalic magmatism. Hydrothermal alteration assemblages are zoned, with potassic cores and propylitic haloes overlain by extensive domains of clay alteration and silicification (lithocaps). Copper sulfides, gold and molybdenite typically occur in veins or hydrothermal breccias, and less significantly as wall rock replacements. Epithermal deposits may form above or to the side of porphyry systems, and may be juxtaposed into the core of a porphyry deposit if rapid uplift and exhumation occur through the life of the magmatic-hydrothermal system. Volcanichydrothermal breccia pipes (ædiatremesÆ) commonly form late in the life of a porphyry system. They may contain clasts of porphyry-style mineralisation, and can host significant epithermal gold resources. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By M Ewart

The securing of a reliable water supply for a prospective mine in the North West Queensland Mineral Province is usually one of the most influential factors in determining the mine's feasibility. The Ernest Henry Mine required a reliable water supply to serve a demand estimated at feasibility stage to be up to 20 ML/day. Numerous options were considered before a decision was made to construct a 113 km long pipeline from Lake Julius as this was the most cost effective, reliable source of supply. The North West Queensland Water Pipeline is a multi-user, Queensland government funded project initially supplying up to 7000 ML/year of water from Lake Julius to Ernest Henry Mine, with provision made for expansion to serve future users in the region. This paper discusses the history of the pipelineÆs development, together with a summary of the scheme's design features. Environmental and licensing requirements, construction and operational issues are also discussed.

Jan 1, 1998

By S T. Jarvis

Colliery spoil is the major constituent of colliery spoil ærockpasteÆ which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpaste are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising infilling a 6600 m3 section of an abandoned mine was conducted prior to the infilling of the Littleton Street Mine which had a volume of about 500 000 m3. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully used for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over 11 mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998