Search Documents

By Wardle L, Wright G

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modem houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various' house designs.

Jan 1, 1992

By Leach B. G

A geostatistical study was made of diamond drill hole intersections within 18CC stope block at the C.S.A. Mine, Cobar, N.S.W. The stope block is located in 18CC orebody which is a massive sulphide - multiple vein, Copper-Zinc type, lacking clear definition on gangue mineralogy, base-metal assays and total sulphide considerations. Of the variograms constructed for inter- section width and copper, lead and zinc grades and accumulations, only zinc displayed behaviour amenable to model fitting and kriging procedures. Zinc grades were calcu- lated for sub-blocks comprising the total stope block and comparison with equivalent grades determined by traditional methods showed them to be generally less extreme in the highest and lowest grade sub-blocks. The total-block grades derived by the two methods were almost the same. It is suggested that the failure of copper to show variogram continuity might reflect the difficulty in defining the actual 18CC orebody, a proposition which is supported by the poor continuity in the variogram of horizontal width. In the case of lead the poor continuity may be due to the frequent manner of occurrence of galena as coarse grained patches of limited extent. The results of the study, did not provide a convincing reason to depart from the traditi- onal methods of grade estimation at the C.S.A. Mine.

Jan 1, 1979

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

An integrated mining equipment development organisation is typified by Deutsche Montsn Technologic of Essen, Germany. working on improvements in reliability, production and control in coal mines. Examples of recent mining advances are in mechanised roadheading, in different approaches to cutting technology, and in low height roof bolting.On the longwall face the mechanics of cutting are related to supplied energy as well as to dust make. In conveying both armoured face conveyors and conveyor belts are monitored. Roof support is not neglected and the continuous pumping of stowage slurries provides further options for longwall support. Surveying developments, particularly the gyro-theodolite, directional drilling. and shaft vehicle monitoring provide further examples of advances in control in coal mining activities.

Jan 1, 1991

By Cotton P. L

Although the terms "pipe" and "tube" are normally considered synonymous, a distinction is often drawn, the former term being applied to the hot finished product and the latter to cold finished material. It is, considered that the title of this paper includes hot finished seamless, and continuous-weld pipe, cold drawn seamless tubing, and electrically welded tubing.The continuous-weld process will be reviewed first, passing to the various methods of seamless manufacturing, which, in addition to meeting the demand for hot finished seamless pipe, also supply the raw material for cold drawn tubing, the manufacture of which will then be described. Finally the electric resistance-weld process will be Considered, and the paper will conclude with a brief review of the processes described and trends in present-day manufacture.CONTINUOUS-WELD PIPEThe raw material for this process is delivered in the form of coiled, hot finished, strip steel, generally referred to as "skelp". The end of one coil is electrically buttwelded to that of'the next, so forming an unbroken strip. This continuous ribbon of 'steel is fed into a skelp heating furnace, and brought to the correct temperature for the forming and welding operations which follow. This temperature is usually about 1,350°C.The heated skelp issues from the furnace into 'a multistand mill, in which the first pair of rolls is designed to form the skelp into tubular shape, the edges being in close proximity to, but not touching each' other. These edges...

Jan 1, 1951

By Walker K, Burton RC

An outline of the ventilation and refrigeration requirements of deep South African gold mines is presented. This is followed by a brief description of the history of controlled recirculation in mines and the practical and economic benefits such schemes can offer. The potential hazard of a fire in a recirculation system is discussed.The major part of the paper describes the first large-scale field trial of controlled recirculation to be conducted in South Africa. Emphasis is placed on the monitoring system that was used for data acquisition during the trial, and also on a safety system designed to shut off the recirculation fans in the event of a fire.The paper concludes with a review of the latest development work taking place on recirc-ulation safety systems.

Jan 1, 1985

This paper covers the key issues such as orebody geometry and grade, geotechnical data and metallurgical response. These must be considered in selecting a mining system for a new orebody. It then focusses on the advantages of open pit mining over underground mining particularly in the areas of costs, speed of development and safety. Environmental issues with waste storage is the only negative which emerges. Consequently, the majority of new large mine developments continue to be open pits. It is also demonstrated that underground mining continues to play an important role, particulary for high-grade deposits at depth. The impact on ore recoveries of recent developments in stabilised fill technology in underground mining is also highlighted. The importance of economics to the decision on mining method is continually emphasised as maximising orebody value should be the prime objective of this Work.

Jan 1, 1997

By Ghose AK

Design and selection of support systems for longwall faces call for in-depth know- ledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state- of-the-art datalogger system. The mechanised long wall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 KW DERD shearer. The datalogger system was capable of storing data simulta- neously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build- up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

By Filigenzi M. T

Stresses around mine openings at depth can cause the surrounding rock to fail, releasing stored strain energy. When this happens, the rock may literally explode or `burst' into the opening without warning. As mining progresses deeper into the earth, the possibility of seismic events and rock bursts increases. Researchers at the US Bureau of Mines (USBM) are currently studying seismic activity in three underground hard-rock mines in the United States: the Homestake Mine, Lead, SD; the Lucky Friday Mine, Mullan, ID; and the Sunshine Mine, Kellogg, ID. Waveforms from seismic events are recorded by personal-computer-based hardware and software. This information is archived and transferred from the mine sites to the USBM via modem communication links. Then, using USBM-developed software, the events are analysed to determine various parameters, including magnitude, frequency, and location. In addition, researchers are modelling the deep levels of the Homestake Mine using a finite-element code. These models generate stress and displacement values for a given loading condition. By studying material properties, in situ stresses, and seismic activity along with actual scope sequencing, researchers can make correlations between stresses induced by mining and the frequency and magnitude of seismic events. Information on seismic events coupled with results from finite-element analyses have increased understanding of rock mass behavior and the mechanisms that may lead to rock bursts. Optimisation of slope sequencing designs as a result of these studies could reduce rock burst hazards.

Jan 1, 1995

The process selection and design aspects to treat primary ore in a new carbon-in-pulp (C.I.P.) plant while utilizing, where possible, existing equipment and infra- structure are discussed. The existing crushing plant, water supply, reagents, laboratory and infrastructure facilities from the heap leach have been upgraded and expanded to meet the C.I.P. plant requirements. The new power supply is from the North Queensland grid system. A series of metallurgical tests was carried out and a review of the data showed that the primary ore was amenable to conventional cyanide leaching. Following feasibility studies, a new process plant which included grinding mills, leaching, and adsorption tanks, thickener, desorption and gold roam facilities was constructed.

Jan 1, 1989

Previous studies on the blast furnace raceway zone have been undertaken at three levels of scale, namely: laboratory models at low temperature, hot models which simulate coke combustion in the zone, and tests performed on operating and dismantled blast furnaces. This paper reviews the results of this published work on raceways in order to illustrate the factors which affect the raceway shape, size and combustion characteristics. As a result of the work it has been established that raceways are influenced by blast parameters such as velocity, temperature and chemistry, as well

Jan 1, 1981

Environmental considerations were key factors in the design of the Ranger Uranium Mines treatment plant. The mine is located adjacent to the Kakadu National Park and has an average rainfall of 1.6m per annum. Initially, no contaminated water or liquid effluents are to be released from the project area and thus water management is a key design and operating fact. Particulate and gas emission criteria influenced design as did occupational hygiene factors (dust, radon, housekeeping, maintenance access). Equipment selection and engineering standards were conservative and resulted in the plant attaining design performance in less than three months from the date of commissioning. A number of mechanical and operational problems were experienced and are discussed in the paper, however none of these problems have had a significant effect on production.

Jan 1, 1984

By Townsend IJ

The Upper Triassic Leigh Creek Coal Measures which include a number of seams of sub-bituminous black coal are preserved in four small intramontane basins. The largest is Telford Basin, 1,000 m in thickness. The coals, of variable thickness and quality, are mined by open cast mining methods and utilised for generation of electricity at Port Augusta. The combined proven and indicated reserves are about 100 million tonnes.

Jan 1, 1975

The basic methods to remove material from underground mines are to: convey continuously, batch in trucks, or batch in a shaft hoisting system. A critical aspect in shaft hoisting is accurately batch loading the conveyance or skip. During the 20th century, the almost universally accepted method of loading was via a measuring flask. A measured quantity of material was filled into the flask as the conveyance traveled through the shaft and then, when the conveyance arrived at the loading position, it was ædumpedÆ into the skip for hoisting. Two skip loading conveyor systems have been developed in Australia: BHP BillitonÆs Cannington Hoisting System, installed in 1996, is believed to be the first conveyor loading system designed for two skips. Two parallel conveyors were installed with a two-way gate controlling feed onto each belt. Cannington was ideally suited to conveyor loading as the very high ore density and relatively low production rate required a relatively small volumetric storage capacity on the weighed belt. Newcrest MiningÆs Telfer Hoisting System, which is to be commissioned in 2005, consists of a single slewing conveyor loading each skip with 32 tonnes of ore. The development of this system eliminates the two-way transfer, improves the accessibility and minimises the excavation required. While every hoisting system must be considered on its merits, conveyor loading offers significant advantages to the Mining Industry in the 21st century.

Jan 1, 2005

By Dredge K, Becker G

The successful dissolution of the valuable metal components of a solid phase is often a basic requirement for a successful hydrometallurgical treatment process. Sulphide concentrates are often an intermediate product in the production of refined metals. These concentrates need to be further processed to realise the contained metal values in a useful form. Pyrometallurgical techniques have tended to dominate, at least the initial treatment of metal sulphide concentrates. The technology described, Activox«, has been developed specifically for the hydrometallurgical treatment of these sulphide mineral concentrates, in particular those containing copper, nickel or gold. The Activox« dissolution technology coupled with the use of existing, or newly developed, downstream processing techniques, offers alternative processing options for the recovery of full value, saleable metal products. The technology is suitable for application down to relatively small scales opening up the opportunity for on-site production of metals even at modest scale mining Operations.

Jan 1, 1995

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100% recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after twelve years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By Matthews SM, Gooding JE

N Longhole Open Stope at The Zinc Corporation Mine was developed in an area with large and continuous tension cracks. These cracks resulted fran widespread block subsidence into previously mined areas. The practical problems encountered and their solutions are discussed together with an outline of a new method of stope wall support using large diameter dowels installed sub-parallel to the stope wall.

Jan 1, 1985

A nine-month investigation was conducted into the effect on coke quality and blast furnace operation of the addition of bentonite and southern coal to the northern coal fed to the coke ovens at the Newcastle steelworks.Additions of 0·3 per cent bentonite or 25 per cent southern coal to the northern coal increased the coke strength from 15-20 A.S.T.M. stability to 25-30 A.S.T.M. stability. It is likely that improved mixing and blending facilities would, in both cases, give a coke of over 30 A.S.T.M. stability.For the same coke strength, the use of 0 3 per cent imported Wyoming bentonite was considerably cheaper than the use of 25 per cent southern coal, but the use of Australian bentonite promises the same coke strength for still lower costs. Other additives such as coke breeze, charcoal, iron ore fines, and certain other finely divided materials, gave relatively minor improvements in coke quality.There appeared to be sufficient improvement in blast furnace operation and production to justify full scale addition of bentonite to improve coke quality, although other variables, particularly iron ore physical quality, overshadowed on many occasions the effect of coke quality. Further coke trials with southern or bentonite will be carried out when ore quality has been improved by the introduction of ore sintering at Newcastle.INTRODUCTIONDuring the period of operation of the Newcastle coke ovens and blast furnaces from April 1960 (when No. 3 blast furnace was blown in after rebuilding) to December 1960, a bentonite coke trial was carried out based on earlier research findings (Gregory, 1959a, 1959b; Felton and Gregory, 1960; Gregory, 1960) that as little as 0 3 per cent to 05 per cent bentonite clay added to northern N.S.W. high volatile coking coals gave a significant increase in coke strength. The bentonite coke trial was followed by trials...

Jan 1, 1962

An ongoing research program into surface subsidence over Room and Pillar coal mining is described. A subsidence monitoring network has been established for one Room and Pillar mine in the West Moreton Coal Field of South East Queensland, at which pillar extraction is being conducted. The maximum measured subsidence to 28 January 1986 was 638 mm, with movement continuing. Analysis of the monitoring data with view to application of the subsidence pre- diction theory developed by Kowalczyk (1972) is discussed. The Kowalczyk theory provides predictions of subsidence depression, slope of surface, horizontal displacement, surface curvature and horizontal strain, for both the Partial and Total Settlement cases. The development of subsidence with time is also investigated and a preliminary analysis conducted.

Jan 1, 1986

The scheme of rehabilitation of surface plant commenced in 1936, included the provision of improved and more hygienic changing and bathing facilities for the employees.At that time the Thompson's Shaft section of the British Mine was being prepared for a resumption of operations, and it was decided to repair and re-equip the existing building. Thus any new scheme adopted could be given a thorough trial, and the proved arrangement used as a basis for the contemplated new main changehouse on the North Section.Investigations were carried out to determine the most suitable arrangement for the Thompson's Shaft changehouse, to provide for a total of 120 men, with particular regard to the internal fittings and fixtures. Also, as the mining conditions were such that a large proportion of clothes worn underground by miners, etc., were wet by the end of the shift, the problem of drying these clothes in the availaole time from a man coming off shift to his commencing again some sixteen hours later was one of the most important to be dealt with.The changehouses in use on the North mine section of the lease were provided with racks around the walls for the men to hang their street clothes on, and a section was partitioned off to house the mine clothes and their drying facilities. The actual drying was carried out by means of hanging the wet clothes over racks between which ran pipe coils heated by means of hot water circulated from the hot water boiler supplying the showers.This method had proved to be far from satisfactory for several reasons, the main objections being:-

Jan 1, 1940