Search Documents

By Kokubu H, Moro-Oka A

Gaseous desulphurization from hot metal- lurgical slags containing sulphur mainly as sulphide and(or) sulphate was measured under `low at four different oxygen pressures. The total gas rate was from 1.7 to 2,8 litre/min. Crushed slag samples weighing 2 to 12 g were used for the experiments. The amount of SO2 gas evolved from samples kept at 15500 was rieasured over tires ranging from 20 to 300 min. The gaseous desulphurization rate of sul- phide sulphur becomes high as the oxygen part- ial pressure is increased, while that of sul- phate sulphur is high under low oxygen pressure. The effect of basicity on the desulphurization rate of sulphide sulphur in oxygen atmospheres is not obvious in the range of basicity from one to three. Changes in the ratio of sulphide to sulphate sulphur during the run in oxygen axe analysed. Desulphurization reactions and the rate controlling steps are discussed. De- sulphurization phenomena can be explained by inte.-¦ucia.l chemical reaction rate control.

Jan 1, 1980

By I Ross

The ground handling system needed for the second lift of the underground block caving operation at Northparkes Mines had to link into the existing infrastructure. Production requirements indicated that an annual output of 5 Mtpa was necessary from a depth of approximately 850 m. The shaft that serviced the first lift stopped at a depth of 520 m. This paper covers the selection of the design for the system and the factors that were taken into consideration in making the decision. It will describe the installation program and methodology and highlight areas of significance and then detail some of the issues concerning commissioning of the ground handling system.

Jan 1, 2005

By Shining Z

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The rheological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

The changing characteristics of raw materials has highlighted the limitations that conventional vibrating screens have in the handling of fine wet sticky materials. These' limitations have led to the development of a totally new concept of screening, the Rotating Probability Screen. In order to illustrate the practical benefits to be gained by the extraction of fine materials ahead of subse quent processes particularly in the coal industry, the experiences gained in Ro-Pro installations in America, Australia, Europe and Britain are drawn upon.

Jan 1, 1984

By Curless JM, Power SG

Polymetallic hydrothermal veins of the Western Cascades are hosted in propylitically altered Tertiary volcanics of calc-alkaline affinity and (or) in nearby, altered, and compositionally similar plutons. Ores from shallow and now abandoned mines produced mostly gold and were considered to be of epithermal origin. However, recent discovery of breccia and porphyry types of Cu-Mo mineralisation and other data suggest that the deposits of this terrane vary systematically both regionally, south to north, and locally, high to low altitudes. The evidence includes changes in (1) size, composition, and complexity of plutons, (2) types of mineral deposits; (3) assemblages of alteration and ore minerals; (4) trace metal geochemistry of host rocks; and (5) fluid inclusion and sulphur isotope data. They collectively imply a consanguineous origin of vein, breccia, and disseminated-veinlet types of mineralisation by magmatic hydrothermal processes.

Jan 1, 1987

By P J. Harris, D J. Bradshaw

Surface oxidation of sulfide minerals, such as that found in the regions of a sulfide ore body near the water table, can have a significant impact upon flotation. This theme has been explored for Merensky ore type sulfides where an ore containing pyrrhotite, pentlandite and chalcopyrite was thermally oxidised and the role of potential remedies investigated. Back-scattered scanning electron microscope images are presented showing the oxidation layer which formed in the mineral surfaces. These oxidation layers were depleted in both sulfur and iron with incorporated oxygen. Flotation recovery rapidly decreased with increasing oxidation, particularly after 27 days and reached a plateau after 50 days. Up to 27 days, this effect could be partially overcome with higher collector additions. Oxidation had more impact upon the finer size fractions, particularly for pyrrhotite. For more heavily surface oxidised samples, ultrasonic treatment prior to collector conditioning was found to improve flotation recoveries. This treatment had the greatest effect upon chalcopyrite particles. Sulfidisation was successful in restoring the flotation recovery of the heavily oxidised sulfide minerals. Longer sulfidisation conditioning times were not conducive to good flotation recoveries of both oxidised pyrrhotite and pentlandite due to oxidation of the freshly formed sulfide surfaces. For maximum flotation recoveries of oxidised pyrrhotite, pentlandite and chalcopyrite, different sulfidisation conditions are indicated. It appears likely that in a mineral processing operation treating oxidised Merensky type ores, two stages of sulfidisation employing different conditions would be required.

Jan 1, 2005

Filter aids are currently used in many industries to increase filtrate clarity and filtration rates. In other industries filtration could be improved if accept- able filter aids could be obtained cheaply. The present paper describes a simple thermal process for making filter aids from coal, outlines the effects of coal properties and major operating variables, and discusses the properties of satisfactory products. Several possible variations in reactor design have been used experimentally, involving fluidized beds of carbon or inert material, reaction of the particles while entrained in air, and a combination of entrainment and fluidization. The limits imposed on product yields by the composition of the parent coal are considered in relation to a range of Australian coals and one New Zealand coal; and the effects of temperature, residence time, and reactant flow rates have been studied in relation to product yields and characteristics.

Jan 1, 1969

Spatial continuity as described by a variogram is a reflection of the underlying mineralisation/geology. Modelling of the spatial continuity (variogram) must account for both the quantitative data (ie sample grades), on which the variogram calculations are based, and the qualitative information as provided by the geological interpretation. An understanding of the geology and the variogram interpretation tie together the sample values and allow us to go beyond the actual data (Journel, 1995). Variography makes geology transportable and allows the geological interpolations to be channelled downstream into mine planning, ultimately affecting the economic decisions surrounding a deposit. As such the process of variography and resource modelling is critical. Thus consistent expert decisions need to be made which force geologists to have a closer look at the available information and the geological interpretations. The aim of this paper is to provide an overview of the latest developments in visualising variography and to demonstrate their usefulness in decisions regarding the spatial continuity of mineralisation. New ideas concerning potential future developments in visualising and modelling spatial continuity through variography are introduced.

Jan 1, 1996

By Bowden MW

Sintering of lead-zinc concentrates is practised by Sulphide Corporation to provide both desulfurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulfur dioxide gas for sulfuric acid manufacture.Moisture control of feed mixes is of paramount importance in the sintering operation and improvements in this area have realised increases in overall plant performance.

Jan 1, 1985

By Miller M. J, Bauer J. C

The continuous copper drossing process operated at Port Pine since 1962 has had limited copper removal capacity as determined by a maximum tolerable Cu/S ratio in feed and the level of sulphur in blast furnace bullion. Recent process development has been to overcome these limitations to meet increased copper throughput requirements. A sulphur addition system was developed and installed in August 1987. The system has capacity to increase sulphur input by over 150%, meeting the increased copper capacity requirement and also allowing independence from the upstream process for sulphur supply. Developments in process understanding have been applied within the limitations of the existing furnace design with a 10% increase in the maximum tolerable Cu/S ratio.

Jan 1, 1989

By Johnson M, Wooltorton B

A programme of hydraulic fracture stress measurements conducted in surface drill holes along the alignment of the King River Power Tunnel has provided information of importance to the assessment of the extent of steel lining requirements for the tunnel. A significant horizontal stress field has been detected at a location remote from the power station site, with a corresponding absolute minimum stress magnitude approximating the overburden pressure based on depth of cover. Measurements made closer to the power station site (located toward the bottom of a valley) have revealed an apparently relatively destressed region with minimum stress magnitude less than overburden pressure. The implications of these results are discussed.

Jan 1, 1987

Tokyo Metropolitan Government designs the stormwater storage plans in underground, as a measure of flood control in completed urban district and improvement of combined sewarage system. This time, introducing those plans, we report about IKEJIRI and SIN-KOMAZAWA STORAGE TRUNK LINEs design and construction. They are located in Meguro river basin of the Morigasaki drainage area. Both storage trunk lines have capacity to store 15O,000m3 of stormwater. They are in use for countermeasure of flood till Meguro river's strengthening (intensity 50 mm/h) is ended. And after the strengthening, they will be in use for improvement of river water quality, through the storage of combined sewage and first runoff, which, otherwise overflows weirs and flows to river in a rainy day. These storage trunk line's full length is about 5700m. Boring diameter 66140 mm (f = 2672m) and 47800 mm (I = 2866m) of these tunnels are constructed by Mechanical Shield tunnelling method. And boring diameter 3600 mm x 4000 mm (R = 180m) is constructed by NATM tunnelling method. We began works in 1983, and have a mind to complete in 1987.

Jan 1, 1987

By Gonzalez JM

The Pao gold prospect in N. Luzon, is an example of a high sulphidation epithermal gold system hosted in Mid-Tertiary alkaline volcanics, in the Philippine Arc. Styles of mineralization include: quartz-enargite veins, vuggy silica alteration bodies, and pervasive low grade (0.5ppm) gold mineralization, associated with kaolinite-pyrite-quartz alteration, and geochemically characterized by high As and Hg. Early magnetite-epidote-chlorite alteration linked to an unexposed granitoid is overprinted by an extensive zone of advanced argillic alteration (kaolinite-pyrite-quartz). No alunite is recorded. Important controls of mineralization include; a broad anticline intersected by axial faults, permeable pyroclastic units, and upward confinement of the alteration system by a highly impermeable, clay-rich volcanic unit. At this stratigraphic position the most important mineralization waz developed. The Pao high sulphidation system is not closely related to a stratovolcanic centre, and has formed subsequent to deformation of the volcanic field. It may, however, be related to an unexposed comagmatic intrusion.

Jan 1, 1990

The history of potential large scale development at Stawell in northwestern Victoria dates back to 1914, when Great Boulder Mines Limited, of Kalgoorlie, Western Australia, took up options on some of the major mines in the Stawell Goldfield. Despite this and other attempts by various groups over the next thirty years, mining activity on the field gradually dwindled to the retreatment of old mill tailings.A static price for gold and indifferent drilling results prevented a major effort towards reopening the field until the late 1970's. A renewed exploration effort led to the discovery of sufficient reserves to justify installation of a carbon-in-leach gold treatment plant.

Jan 1, 1984

By Patridge A. C

A pilot scale laboratory investigation of manual slurry sampling methods representative of those used in the minerals industry is described. Samples were taken from slurries made up from silica particles of various sizes and in various concentrations from a stirred tank and from the discharge lip of a rectangular launder. Sampling methods from the tank included immersion flasks and several configurations of a suction probe. The launder was sampled using a conventional narrow-mouth ladle and also with a 'mouth organ' stream splitter. Samples were analysed for overall solids concentration and size distribution and showed different but always significant and often large biases relative to the known overall composition of the slurry, the nature and extent of bias being dependent on pulp concentration, particle size, sampling method and sampling location. Results clearly show the very great difficulty of obtaining representative samples by simple sampling techniques, although the data suggest that errors can be reduced by using an appropriately designed and operated suction probe. Further work will be carried out with the objective of establishing guidelines for industrial sampling practice.

Jan 1, 1995

By Sirayanone S, Rashad MZ

An important problem occurring in the iron and steel industry of Egypt is the presence of manganese oxide and chlorine with different percentages in the Bahariya Iron Ore Deposit, Western Desert, Egypt. In this work we used a geostatistical method known as the Volume- Variance Relationship to predict grade fluctua- tions of Fe% , Mn% and Cl% in the ore after blasting a certain volume from the ore deposit, on the other hand, if we have a certain limit for each of these chemical components, we can select the bench blasting dimension to give these limits.

Jan 1, 1986

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

Depressed prices for minerals will force the mining industry to became more efficient. The continuous conveying of pit product is one area in which savings can be made. Conveyors are available, or can be adapted to provide the flexibility and reliability required. Each conveying system will need to be custom designed to suit the particular requirements of the mine. The Australian mining industry must take the initiative and accept the challenge of the new technology.

Jan 1, 1986

By Wang QP, Quan YH

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

Solution transport of gold and silver has occurred as a result of the chemical weathering of many Western Australian epigenetic gold deposits. Evidence for the remobilization of gold exists in the form of small crystalline octahedra, mustard gold, flake gold, and coatings on iron-oxide. This "secondary" gold is of high purity (low silver content). It is believed that the high chloride content of laterite profiles combined with the acid produced by the oxidation and hydrolysis (ferrolysis) of iron has caused dissolution of Au/Ag and Au/Te alloys. Gold, and less frequently silver, is subsequently reprecipitated in the profile nearby.Pyrite, which is a ubiquitous accessory of gold in vein or lode systems, is probably an important source of iron for the development of acidity. Where carbonate is abundant in the primary assemblage, neutralization directs the oxidation of sulphide to a path which produces thiosulphate, and an alternative type of Au/Ag oxidation process. Sulphide/carbonate ratios in the vein system, and adjacent wallrock are seen as important in determining the course and extent of remobilization in the oxidized zone of gold deposits.

Jan 1, 1984