Search Documents

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

By R Frew, E Wong, G Ferguson

The Chang Jiang Tunnel and Bridge Project, when completed, will provide a fixed link between ShanghaiÆs rapidly developing Pudong District and Chong Ming Island, situated in the Yangtze River delta. The link includes 7.5 km of bored tunnel from the Pudong to the intermediate Changxing Island from where the link comprises viaduct and a cable stayed bridge. The bored section comprises twin 13.7 m internal diameter segmentally lined three-lane highway tunnels. At its deepest point the tunnel will be 55 m below the river. Cross passages will link the two bores for passenger evacuation. Tunnel boring commenced in October 2006 and is scheduled for completion in mid-2009. The paper describes the key features of the design and construction of the bored tunnel by two 14.53 m diameter slurry TBMs and eight cross passages using ground freezing techniques in alluvial sediments. A decision to include light rail below the road deck was taken after the completion of the detailed design. This posed a number of design challenges including passenger evacuation to the road deck, and the redesign of the low point sumps. The various options considered are discussed together with those adopted for construction.

Jan 1, 2008

As this district is so far distant from the other mining centres and its mode of approach so circuitous, I am afraid that many residents of other portions of the Commonwealth never think of paying this" Australia's Silver City" a visit, to learn personally the many and various lessons everywhere available, and to become familiar with the really wonderful and interesting features and deposits (which pature has so lavishly bestowed in the mineralogical world) yet seemed to almost ignore or overlook when disposing of topogr,aphical beauties of landscape and vegetation) unless professional or business duties require their presence here. So it is to those whose life is necessarily spent in other parts of the States where they answer their call of duty, and yet feel an interest, either for business or other reasons, that my paper is specially addressed and prepared, and for that reason I witl endeavour to make my remarks more of an explanatory than a dictatorial nature. I feel sure that there. are many members of our Institute who are much more familiar, and have had many more years' experience in the various methods of timbering, filling, and ore extraction, etc., than myself, but I hope that over I6 years' experience in connection with mines and engineering works, the last six of which have been spent in Broken Hill, where, I have been very closely connected.

Jan 1, 1903

By A Kuras

Segmental tunnel linings are becoming more common in Australia. One current project employing a segmental lining is the City West Cable Tunnel (CWCT) in Sydney. The project has been commissioned by Energy Australia and is currently being constructed by Thiess Pty Ltd. The project includes 1.6 km of tunnel boring machine (TBM) driven, segmentally lined tunnel. The majority of the CWCT will be excavated through Hawkesbury Sandstone. The tunnel is required to carry a 132 kV electrical circuit under SydneyÆs central business district (CBD), between Haymarket and Energy AustraliaÆs City North Substation on Sussex Street. The segmental lining has been designed as a 3.2 m internal diameter, 200 mm thick universal ring with six trapezoidal segments. The design and detailing of this segmental lining presents some noteworthy challenges, including exposure to saline groundwater, and the exclusive use of steel fibres for flexural and tensile concrete reinforcement. This paper describes some of the key elements of the segmental lining design. These include:the case for choosing segmental linings over other forms of tunnel construction;the major design checks required of a segmental lining including ground loading, hydrostatic loading, joint bearing, joint rotation, ram loading and the early strength lifting case;the benefits of using steel fibres over conventional steel reinforcement;the design approach used for steel fibre reinforced concrete;the application of 3D computer modelling in the design;the provision for components including connector dowels and gaskets;the design for passive fire resistance; andthe design for durability of steel fibre reinforced concrete in a saline environment. Segmental lining design requires the application of specialist design approaches. Input is required by the construction team, as the methods of demoulding, handling, transportation and installation impact on the lining design. As the segmental lining is functioning as immediate ground support and also a permanent lining, high standards of manufacture and construction quality control are required to ensure that the 100-year design life is met. The requirement for a watertight tunnel means that detailing and installation of the EPDM gaskets is of importance.

Jan 1, 2008

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

Krupp Polysius AG, FRG, in close cooperation with Prof. Dr. K. Schoenert, FRG have developed the principle of the high pressure grind- ing roll POLYCOM. The POLYCOM mill basically consists of two counter-rotating rolls of large diameter and relatively small width, one of which is fixed and the other moving in slide blocks. The pressure required for comminu- tion is applied via the sliding roll by a powerful hydraulic system. The comminution takes place between the rolls under high pressure in the bed of material by nipping and compacting. The top feed size-depending on the rolls diameter -may be as coarse as conventional secondary crusher feed and the product is a compacted cake containing a high amount of fines created by micro-cracking. The amount of fines depends on the pres- sure (grinding force) applied. Operating results show that even in wet griding circuits capacity increases at downstream connected grinding mills of up to 100010 can be accomplished with an interconnected POLYCOM machine and energy savings of up to 25070 may be achieved depending on application. POLYCOM can be used in existing grinding plants for low-cost upgrad- ing of capacities but also as an advanced alternative to conventional crush- ing and grinding equipment in open or closed circuit configuration. A single industrial size 2.8m roll diameter POLYCOM machine may be fed with top feed size of up to 200mm and produce a finish product as fine- grained as known from rod and ball mills but with less energy consumption. Meanwhile, the POLYCOM high pressure grinding roll has established itself world-wide in the cement industry and is now entering the mining industry. POLYCOM machines are currently designed in industrial standard sizes of 1.0m to 2.0m rolls diameter and drive units of up to 2400 kW. This paper includes: principles of high pressure grinding, main fea tures of the POLYCOM machine, results of tests on various materials including Australian gold and copper ores carried out at the POLYSIUS research centre in Germany. Some examples of industrial applications of high pressure grinding will also be presented.

Jan 1, 1988

In a state-of-the-an review of predictive methods for longwall support load calculation, special respect is paid to those techniques which enable actual roof conditions and local lithology of strata to be involved. Principal systems of roof examination include the borehole perforation test and seismic velocity measurements. Roof strata stability is related to caveability classifications and roof inclination due to subsidence. The critical analysis of both load resistance prediction methods and roof stability classifications shows that each has its own value of reliability level. The present research opportunities analysed underline the significance of developing fully reliable prediction techniques as needed by the coal industry.

Jan 1, 1991

By Walker G. S

Infrared and Raman spectroscopy have been used to study a range of solid state and aqueous solution species which are of interest in extractive metallurgy. In the solid state new Cu(II)/CN'/NH3 complexes have been detected, iron impurities in kaolin characterised, aluminium substitution in hematite and goethite quantified, and the crystallinity and orientation of zircon determined in heterogeneous crystals. In aqueous solution metal cyanide complexes and equilibria were readily characterised, the thermal decomposition of SO2 monitored and products identified, and complexation of AI(III) by hydroxycarboxylates observed. Attempts to monitor the early stages of the gelling of silicate solutions were less successful, with only changes in the gel being detected. However, the degradation of 12-tungstosilicic acid was readily monitored as a function of both time and pH.

Jan 1, 1996

The products from beneficiation present themselves at opposite ends of the spectrum, and yet numerous synergies exist in the preparation of coking coal and hematite iron ore products for their common export markets. Returning to the coal side of the business with Anglo Coal following a five-year sojourn in WA with Hamersley Iron, has provided the opportunity for comparing and contrasting some of the key synergies of the supply chains of both bulk commodities.Comparisons include consideration of things like: resource evaluation (especially quality aspects), run-of-mine handling and preparation, beneficiation, product handling and transportation, quality assurance and customer awareness, value-in-use and impacts on iron and steelmaking, and supply chain environmental aspects.Inherent within these are several other notable contrasts including: æseamsÆ and æorebodiesÆ, rocks and minerals, rejects and tailings, oxidation and weathering, suppliers and users, and marketing and purchasing, to name but a few.This paper covers some of the more interesting of these synergies and raises some potential opportunities for sharing knowledge and innovation between the two areas of activity in the future.

Jan 1, 2005

By McPherson M. J

An experimental investigation was carried out to determine the various gas flow characteristics of bituminous coal samples. Adsorption and desorption tests were first conducted to estimate the quantity of methane that is retained by coal, and the rate at which it is released. Experiments were then carried out to study the variation in coal permeability with changes in applied stress and gas pressure - factors that change continuously with time. To further understand the phenomena involved in retention, release, and flow of gas, electron microscopy was used to study the microstructure of coal and how it affects these characteristics of coal.

Jan 1, 1988

The mined-out Old Waite volcanogenic Cu-Zn deposit lies in the Noranda mining district of northwestern Quebec. The deposit has a distinctive pipe-like zone of alteration beneath the massive ore, extending into the stratigraphic footwall. The hydrothermal metasomatism within the alteration pipe produced a concentric zonation. with a peripheral quartz - sericite - chlorite mineral assemblage surrounding an axial core of magnesian chlorite - Phlogopite.

Jan 1, 1989

Relationships between lead blast furnace performance and the composition and size distribution of sinter were determined from analysis of lead blast furnace operating data. Sintering plant practice was subsequently modified and substantially improved furnace performance resulted.

Jan 1, 1971

By D S. Nicholson, T Marshall

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while opencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By Lawrie DC

Finely ground beryl was decomposed by mixing with ground limestone and soda ash andheating at 900¦C for,4-6, hours.The sintered material was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hours. The liquor containing Be, ; Al, . Fe and, other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either' by filtration or by decantation washing.The clarified leach liquor.was first treated to remove Fed}: , by contacting with a primary amine-kerosene solution in2 counter-current stages. The iron free liquor wa,s then passed to a 4-stage counter-current extraction unit where it was con-tacted with 0.5M di-(2 ethyl hexyl), phosphoric acid (EHPA) in kerosene. The'operating conditions were such that at least 99 p'br cent of the Be and only 7' per' cent of the Al- was, extracted The ,B6`= and. Al were ;stripped from the organic phase by sod-ium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipTitated a's Bo(OH)2 by-hoating the alkaline solution to 90C, the Al remaining in solution. After filtra-tion and washing, the Bo(OH)2 could be ignited directly to BeO at about 1000 C or used as a feed to further purification stages aimed at producing "nuclear grade" BeO.A small coaAter-current extraction unit was operated con-tinuously using liquor derived from the sintering and leaching stages. Data obtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precip-itate contained more than'99 per cent BeO.

Jan 1, 1963

By A Hewitt

Portland cement is the chief binding ingredient in mine backfill. In the presence of water, the chemical compounds within portland cement hydrate causing hardening and strength gain. During hydration, heat is generated. In certain cases, hydration heat may be produced significantly faster than it can be dissipated, which can create high temperatures in the underground environment. This paper presents the results of a series of investigations aimed at quantifying the heat generated by cemented backfill during hydration. Scaled stope models, instrumented with thermistors, were used in the investigation. Heat transfer to the hanging wall, orebody, footwall and cross-cut and production drifts was assessed during the backfill curing process and relationships between cement content, cure time, and heat generation were developed. The results of this work will assist mine operators in predicting the heat generated by cemented backfill and provide the necessary information to implement effective engineering control of heat in the underground environment.

Jan 1, 2005

Australia contains a variety of iron ores, differing in grade, chemistry, size distribution and genesis. While a proportion of this ore is used world-wide as blast furnace lump, much of the material mined is high grade fines, requiring agglomeration (usually sintering) before blast furnace reduction. Sintering studies initially concentrated on the production of ferrous material of high iron content, coarse size and sufficient cold strength. In recent years research involving pilot plant sintering, precise test procedures and mineralogical analyses has focussed on the additional sinter properties of hot strength and reducibility. Aspects of mineralogical studies applied to iron ore sintering are described.

Jan 1, 1989

By D J. Black

The process of excavating and mining coal causes fractures in the overlying and underlying strata. The fractures provide pathways for gas released from coal seams and other gas-bearing strata to flow into the mine workings. Coal seam gas typically contains high concentrations of methane with lesser concentrations of carbon dioxide. Low concentrations of other gases such as nitrogen, hydrogen sulfide and ethane may also be present in some coal seams. In certain geological settings, particularly in close proximity to geological structures, such as faults and dykes, the concentration of gases contained in a coal seam can vary significantly between methane-rich to carbon dioxide-rich.In mine design and planning it is vital that mining engineers gather sufficient information to accurately determine the content and composition of the gas present in the coal seam and develop an understanding of changes in these parameters within the planned mining area.The longwall method of mining coal causes fracturing of the overlying and underlying strata behind the retreating longwall face. Where coal seams and other gas-bearing strata are present within the caving zone, gas will be released from the strata leading to contamination of the mine workings. If the rate of gas emission exceeds the diluting capacity of the mine ventilation, the concentration of gas in the mine may exceed the statutory limit, resulting in production delays and potentially unsafe conditions.CITATION:Black, D J, 2016. Planning effective management of gas emissions in an underground coalmine, in Proceedings Life-of-Mine 2016 Conference, pp 44–47 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Mauk JL, McOnie A, Simmons SF

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water, whereas the mineral assemblage of replacement calcite-interstratified illite - montmorillonite- kaolinite forms a carapace and reflects formation from a C02-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

The sedimentery basins of this region developed in the collision zone of the Pacific Ocean plate and the continent. Stresses were transmitted thorough wedge-like lithospheric blocks, such as the Okotsk Sea, East Kamchatka, Aleutian and 2 other smaller blocks. Compression and inversion were more active at the boundaries: P ; P3 ; N1 ; and Z N in places. ? K2 P2 P3 N2 Tension, rifting and the increase in the rate of sedimentation were marked in '-2 , P3, Ni - N2, and also N2 - Q in places. Structural plan changes of the sedimentary basins and possible oil, gas and fluid migration occurred more actively 2 3 1 2 at the boundaries: ; P3 . N? , N1 N1 NZ N2 P2 P3 1 N1 'N 2 N3 Ni 1 1

Jan 1, 1995

Perhaps no aspect of the investigation of an ore-deposit is of greater importance to the mining geologist and engineer than a consideration of its geological structure. A thorough understanding of the type, size, shape, and arrangement of any ore-body is essential to the proper conduct of exploratory, developmental, and mining, operations. Significant as these remarks are' in relationship to ore-deposits in general, they become of paramount moment when a complex structure such as the Broken Hill Lode is in question. In this connection the use of the term "lode" as applied to the Broken Hill ore-bodies may terid to confusion of ideas among those not familiar with the field or with the literature pertaining thereto, by reason of the fact that it is generally understood that a "lode" is characterised by simple, tabular form, regular outline, defined walls, and persistent attitude. However, as the terminology is well established by common usage, itsretention appears desirable, and, for the purpose of this paper, the name "The Broken Hill Lode" refers to that complex unit which includes pre-eminently the famous ore-bodies exposed in the workings from the North Mine on the one extreme to the South Blocks (Zinc Corporation) Mine on the other.That the practical value of geological investigation, of the ore-bodies was realised by the Geological Sub-Committee of the late Scientific Society of Broken Hill is attested by the...

Jan 1, 1932