Search Documents

By M J. Pejovic, S BoÜevski, I Miljanovic, M Hudej, A Milutinovic, A Petrovski

The paper deals with the problem of managing the supplies of consumables (energy resources, lubricants, explosives, explosive supplies, tires, spare parts, etc) in mines. After the introductory remarks and comments, a general stochastic model of supply, relating in general to the dynamic programming method is presented. A selection of stochastic supply model for experiments and research by the authors of this paper is not a coincidence, based on of their long experience, showing that this type of model is the most suitable to provide support for decision-making and management of supplies of consumables in mines.In order for the problem?of?consumables?supply?management to be reviewed, in whole and objectively from the aspect of risk, experimental tests of the stochastic model in real conditions were performed at the limestone open pit mine æZelenikovecÆ near Skopje, the capital of Macedonia. The scope of the experimental research enabled reliable analysis. The results obtained confirm the efficiency and reliability of the stochastic model and two separate manipulative-operational positions regarding its application, which may have an important influence on the optimisation of supplies.

Sep 26, 2011

By A L. Bennett

It is well understood that designers and constructors must protect the existing surroundings of tunnel construction, particularly in the selection of excavation methods, ground support and waterproofing systems. However, while this can readily address the existing conditions, the tunnel owner and the designers need to consider the changes that are likely to occur during the life of the tunnel. It is typical for transport infrastructure to have a design life of at least a century. While the effects of constructing the tunnel on its surroundings are a short-term effect, the converse case, the protection of the tunnel, and the need to maintain its integrity, will affect developments over and adjacent to the tunnels beyond the foreseeable future. Decisions made during the design phase have the potential either to facilitate development or to hinder it for the long term.Examples principally from Australia, New Zealand, Singapore and Hong Kong show that the provision for future development is addressed in different ways. These have ranged from making no specific provision, putting the onus onto developers to ensure that the tunnels are not affected adversely, to including a loading allowance for future development in the performance specification or contract documents for a tunnel project.These two contrasting approaches have strong points and risks. A highly prescriptive definition of permissible loadings around the tunnel can provide unambiguous guidance for the approving authority and the developer, but runs the risk of being overly conservative to allow for all the envisaged works, while still missing a detrimental combination of effects that theoretically complies with the specified requirements. In contrast, a general requirement to not cause detriment is open to interpretation and potentially difficult negotiations to reach agreement between the tunnel owner/operator and developer and finally the appointed contractor (probably with no contractual relationship with the tunnel owner).In practice, a combination of prescriptive and performance requirements is likely to provide the optimum combination of clarity and flexibility. The author provides examples and recommendations on how such provisions could be structured.CITATION:Bennett, A L, 2014. Protection of ?tunnels in their future environment, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 495–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The mining industry has expanded significantly in the Pacific Region over the past two decades through a mix of new developments and brownfields expansions of existing operations. Despite this overall success there are also a number of well publicised examples of less than successful minerals ventures. These problem developments highlight the fact that success cannot be taken for granted and that rigorous planning and attention to detail is essential. The dominant growth has come through expansion of existing businesses, notably alumina, iron ore and coal, achieved through both efficiency gains on existing plant and step change capacity additions such as new mines and/or expanded processing plant. This expansion has largely been linked to increased market opportunities. The major issues are the quality and extent of the host resource, achieving the market targets, and the efficiency of the expansion effort. There can be also a range of site specific issues which need to be addressed. The development of new greenfields operations is often more complex as it can bring a wide range of new issues. Depending on the nature of the development, and the companies involved, these can extend from initial financing through to obtaining a market position. Incorporating major new technology and/or establishing infrastructure and attracting staff to remote locations can also add significant challenges. This paper outlines many of the critical factors which need to be considered prior to proceeding with major expansions or greenfields developments. These will be linked to a number of developments in the region over the past decade.

Jan 1, 2004

By A S. Derrington

This paper describes a hybrid ventilation system, which uses secondary fans that also act as de-facto primary fans to extract fresh airflow from the mine intake raise system. Also discussed are the associated problems such as uncontrolled recirculation, inadequate decline airflow, fire safety issues, prolonged blast fume clearance times, high air temperatures in main access routes, neutralisation of mine air cooling by heat from secondary distribution fans, increased ventilation system complexity, reduced flexibility and high pressure differentials (which cause safety issues with personnel access and reduce secondary ventilation system performance).Practical suggestions are provided on options to avoid these problems listed.CITATION:Derrington, A S, 2013. A critique of the push-pull hybrid ventilation system, in Proceedings The Australian Mine Ventilation Conference , pp 73-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By M Tayebi-Khorami

There is an increasing trend in the extraction and development of copper resources from complex deposits. The complex deposits pose mineral processing challenges, as they often contain low grade copper ore, relatively large quantity of clay minerals, complex texture, very fine disseminated ore, high amount of pyrite, and high level of impurity elements such as arsenic. With the amount of arsenic in concentrates increasing and with environment, occupational health and safety regulations becoming more restrict, there is a need for a processing method that results in no arsenic emissions and captures all arsenic while immobilizing it in a compound that is stable under a wide range of conditions, so it is suitable for long-term disposal. Some development work has been undertaken to examine the most effective arsenic treatment option for complex orebodies that contain arsenic, but a technically robust and economically viable option has not yet been developed. Previous research has demonstrated the possibility of separating arsenic-copper sulphides from other copper minerals by controlling the potential of the flotation pulp in the single mineral systems. The selective flotation of enargite from copper sulphides in a real complex ore system was studied by Tayebi-Khorami (2016), which is summarised in this paper. CITATION: Tayebi-Khorami, M, 2018. Arsenic in complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 132–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By G I. Lumley

‘Every mine is a pilot’ is an attitude which encourages the mining paradox of optimistic mine plans and equipment under performance; propped up by an environment lacking accountability. The premise that ‘every mine is a pilot’, appears to underlie the development and operating approach to most mines. It is the hypothesis of this paper that many mining companies, development teams and their managers largely ignore what is done elsewhere. Anecdotally, most planners don’t know whether the selected rates are high or low (rates based on theoretical models tend to be high – certainly higher than what most companies can achieve). Mines then consistently operate the equipment at rates well below targets; often more than 20 per cent below. Further to this paradox, mine performance data demonstrates the average mine is currently operating their equipment at levels of output not much more than half the output of those in the top ten per cent. On the whole mines don’t know the potential of their equipment and therefore don’t put appropriate plans in place to do better. After all, when ‘every mine is a pilot’ there is little reason to look to one’s peers for an indication of potential. This paper will outline why every mine is not a pilot and how mines do value some knowledge, but not as much as they should. This paper proposes a two-pronged approach to address this issue in the area of equipment performance. This approach is to:1. engage in better forecasting of equipment rates and better subsequent performance through benchmarking against industry standards2. provide conditions for more accountability.These parameters are linked and proper implementation of them will address the losses which many shareholders and financiers have incurred when investing in companies with unrealistic mining plans.CITATION:Lumley, G I, 2016. Is every mine a pilot? In Proceedings International Mine Management Conference, pp 75-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

The production of synthetic rutile from ilmenite using hydrochloric acid leaching is investigated. Previously published data is used to comment on the optimum process conditions. It is shown that the most important aspect to consider is the maximisation of impurity dissolution and the minimisation of titanium losses.

Jan 1, 2001

By I Gray

This paper examines the effects of the changes in stress that a coal may undergo as part of the drainage process. As a consequence of this, some coal seams will come to the situation that they have zero horizontal stress existing within them at the time of mining. The hypothesis of this paper is that this lack of horizontal confining stress means that on mining, the vertical stresses may be easily raised to a level where failure occurs. This failure may be accompanied by significant energy release from energy stored within the coal as well as that coming from the roof and floor. To determine the state of stress within the coal seam, the concept of the effective stress path that the coal passes through is examined and is found to be very dependent on the shrinkage of the coal with degassing, the Young’s modulus of the coal and its Poisson’s ratio. The Young’s modulus of the coal is important and has been found to be highly dependent on the state of stress within the coal. It may change by more than an order of magnitude.CITATION:Gray, I, 2014. The consequences for pillar stability of zero confining stress brought about by forced or natural drainage, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Morgan

Regular monitoring of surface deformation over mine sites is important for providing updated information to managers regarding geotechnical risks related to ground instabilities. This is particularly true in cases where unexpected or accelerating movement patterns are observed, as these trends may have implications related to worker safety within active mining environments, as well as continuity of ongoing operations. InSAR is an active remote sensing technique that uses radar satellite imagery to precisely measure ground movement. This technology has started to become a standard tool for monitoring surface stability in many different sectors, including underground and open pit/cut mining applications. In recent years the launch of satellites that collect radar imagery on a more frequent basis, coupled with advances in InSAR processing techniques, has improved both the extent to which movement patterns typical of mining operations can be characterized and the temporal scale on which results can be reported to geotechnical departments. As a result of these developments, InSAR monitoring can now better meet the operational needs of mine sites. An overview of the more recently launched satellites that have a particular relevance to the monitoring of mines is provided, along with an explanation of the InSAR tools that are the most valuable to mine managers and geotechnical engineers. First, broad differences between high resolution X-band imagery and low resolution (but freely available) Sentinel imagery are discussed. Second, the various InSAR tools and their particular applications for different types of mine sites and operations are covered, which include fast delivery deformation maps for short-term reporting, multi-interferometric algorithms for longer-term analyses and rapid movement tracking (RMT) for emergency monitoring or high-risk situations. The ability of the technology to resolve 2D and 3D movement is also touched upon. Practical examples of InSAR application over a variety of mine sites will be presented, as well as surrounding hazards including landslides, to illustrate how InSAR can help provide geotechnical engineers with a picture of surface stability over the full mine site and surrounding areas to help manage risk. CITATION:Morgan, J, 2018. Wide area mapping of ground instabilities from space: InSAR for geotechnical risk assessment and hazard monitoring, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 375–382 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By P R. Botha

Mining has played a significant role in human development and without the mining sector, society would not enjoy a large number of the benefits that it does today. However, mining has also carried with it some important lessons, which remain the source of ongoing learning. One of these lessons is the poor closure or abandonment of mines, worldwide. This has in many cases resulted in large tracts of unproductive land, representing a source of environmental pollution and a safety hazard to the community. Frequently associated with this is a legacy of mining communities having fallen into economic and social decline, beyond mine closure.Due to this legacy, governments, society and the mining sector pay far greater attention to mine closure planning today, than was done in the past. Typically closure planning has focused on the engineering aspects of a mine, namely decommissioning of the workings and plant; dismantling of unusable infrastructure; and rehabilitation of disturbed land. These are important aspects of closure but a more holistic, long-term approach is required which encompasses environmental and social aspects and aims to leave a positive legacy behind.In planning for a mine closure scenario with a lasting positive legacy, it is critical that the broader receiving environments (social, economic, physical and biological) within which a mine is located, define and drive the closure plan and the mine planning as a whole. This ensures that the broader environment influences mine closure, as opposed to looking at how a closed mine will impact on the environment. The ultimate aim is to first understand the broader environment and then to fit the closure of a mine into it. The earlier this approach is followed in the life of a mine, the greater the operational time frame available, and hence a better chance is presented for planning and managing a mine towards the desired, tested and agreed post closure scenario. Within this broad context, there is tremendous scope to achieve successful mine closure. However, it is critical to note that mine closure is not the sole responsibility of the mining companies, and neither is it possible for said mining companies to achieve mining closure alone. This concerted effort requires a multi-stakeholder approach in which partnerships are created and risks, responsibilities and opportunities are shared and managed. To achieve sustainable closure, a multi-stakeholder approach based on an initial forward-looking closure vision is required. This approach provides an early basis for consideration of alternative land uses and economic options from which specific actions to achieve the preferred option can be defined. The Anglo American plc Mine Closure Toolbox has been formulated and developed around this concept. The Toolbox aims to expand mine closure planning - from financial provisioning for rehabilitation and physical closure, to planning for sustainability beyond mine closure and leaving behind a positive legacy.This paper focuses on the business case for mine closure planning and provides an overview of the Anglo American plc (AAplc) Mine Closure Toolbox.CITATION:Botha, P R, 2012. The business case for mine closure planning and an overview of Anglo AmericanÆs mine closure toolbox approach, in Proceedings Life-of-Mine 2012 , pp 7-10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By H Mischo, M Ferber, M Donner, B Jung, S Grehl, A Dietze

Mobile robots have been making impressive inroads in a variety of domains. Within the Mining-RoX project, Technical University Bergakademie Freiberg is exploring a further frontier for mobile and autonomous robots: underground mines. The potential benefits of mobile robots in underground mining are plentiful as underground mines are strenuous and potentially dangerous working environments for humans. A higher degree of automation, with robots either acting as helpers for human miners or even replacing all human personnel deployed underground, could help to significantly reduce mining costs. In disaster cases, rescue robots could help to find missing personnel. Unmanned mines operated by robots alone would not endanger human lives at all. Further use cases, and a particular focus of the Mining-RoX project, are mobile robots that gather sensory information of the underground mine (eg for the purpose of creating detailed 2D and 3D maps) as well as monitoring environmental conditions such as air and water quality. This paper presents the design of a prototypical mobile robot for mapping and monitoring underground mines. A generic robotic platform was extended with various 2D and 3D imaging devices as well as other sensors. First results from test runs in an underground mine are reported. Maps of two sections of the mine enhanced with localised sensor measurements were successfully created.CITATION:Grehl, S, Donner, M, Ferber, M, Dietze, A, Mischo, H and Jung, B, 2015. Mining-RoX – mobile robots in underground mining, in Proceedings Third International Future Mining Conference, pp 57–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By E Wargem

The conventional method of underground mining involves a process known as drilling and blasting to excavate valuable ore bearing minerals through the load and haul process. Drilling and blasting processes are completed for both the development of the tunnels used to access the orebody and for mining out the orebody itself. The former being called development drilling and blasting, and the latter production drilling and blasting. In either development or production drilling and blasting, the effective recovery will be largely reliant on the extraction of the initial void created in each blast cycle. In development tunnelling, the initial void is commonly known as a Burn Cut. The initial void created in production drilling and blasting has many names such as a Slot, Winze, Rise or Raise. There are drill patterns and charge designs used to create these initial voids in the production cycle. This paper discusses common slot or winze designs for production drilling and blasting; and various critical design criteria for these. The document also aims to provide a process for completing desktop reviews of current patterns employed on-sites and provides an initial guide in a process for improving the recovery of a slot, winze, rise or raise in underground mines.

Mar 29, 2023

The environment has emerged as a permanent component of Australia's socio-political context, intricately linked with personal and future security.The implication of this powerful new influence on the Australian Minerals and Energy Industry sector has been a plunging public image.

Jan 1, 1993

By R Shaw

There are many small to medium carbonate hosted complex zinc containing deposits where the zinc is not economically recoverable either as concentrate or metal. High grade (>20% Zn) run of mine ore can be processed but even this material gives relatively poor returns. Considerable effort has gone into developing new technology for either upgrading the ore and/or recovering zinc metal hydrometallurgically but there has been limited success. Minetometal has developed a process capable of economically treating these deposits to give marketable lead and zinc products. This paper reviews alternative processes for these ores and gives a detailed description of the Minetometal Process. CITATION: Shaw, R, 2018. Processing carbonate hosted zinc-lead ores, in Proceedings Complex Orebodies Conference 2018, pp 130–131 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Smith J. W, Hart G. N

Compositional and isotopic analyses of coal seam gases in the Southern Coalfields have shown that these gases frequently contain abnormally high concentrations of magmatically derived carbon dioxide. The size of this carbon dioxide reservoir and the extent of permeation of the sediments by carbon dioxide are not known.Therefore caution in evaluating the natural gas potential of the region is advised.

Jan 1, 1981

Pyrrhotite is pyrophoric when in a finely divided form. The problems of disposing of large quantities of finely divided pyrrhotite separated out by metallurgical processing from ore are formidable. In the case of an underground mine, a solution to the problem of disposal is to place the pyrrhotite in the stoped out areas and seal from any air supply. Further, the pyrrhotite could be diluted with tailings which would reduce the possibility of combust- ion. Several enquiries to various centres and authorities have shown that the products of the slow oxidation of pyrrhotite with moisture present can cement an inert matrix into a stable fill similar in physical prop- erties to fill stabilised with Portland cement. Stabilised fill can be used to advan tage with a suitable mining method to provide high recovery. The investigation demonstrated that air and 15% w/w water must be present for the fill to harden and that the sizing of the particles is a critical factor in drainage of a hydraul- ically placed fill and subsequent even harden- ing of the fill in a stope. With the materials used in the experiments in which the - 51 micron component of the tailings had been dis- carded, an optimum mix was found to contain 4:1 tailings/slag ratio and an overall pyrr hotite concentration of 8% (all proportion by weight). Approximately 34 days after drain- age to 15% moisture in natural air flow condit- ions, an unconfined compressive strength of 1.862 MPa was attained. A subsequent experi- ment was conducted with a sample of optimum mix in a pipe one metre long in forced air flow conditions. At a superficial velocity of 3.Om per hour the mix required 155 hours to harden to 1.862 MPa after drainage to 15% w/w moisture content. The pressure drop bet- ween the top and bottom of the mix in the pipe remained constant at 9 KPa/metre length. This result suggests that forced air flow conditions will increase the rate of hardening. No dangerous effluents were detected in the course of the experiments which could affect mine equipment or personnel.

Jan 1, 1973

By A Gray

Physical separation features in almost every mineral processing circuit. The category encompasses a broad range of techniques and technologies including hydrocyclones, gravity concentration methods (including jigs, spirals, centrifugal concentrators, tables, heavy media separators) and thickeners, all of which make use of the inherent density differences between two mediums. It is also possible to include flotation, magnetic separation, and ore sorting in the physical separation category.However, opportunities for enhanced physical separation performance can now go beyond the common practice of optimising unit operations. Improved options exist for feed preparation ahead of the physical separation stage, enabling higher performance and lower cost outcomes for physical separation flow sheets and technologies.The use of new applications in breakage technologies combined with mineral liberation analysis to optimise liberation prior to the physical separation stage provides options for preconcentration and gangue rejection as well as better separation efficiency. The use of low cost gangue rejection and preconcentration can be an intermediate step between mining and processing that allows processing of lower cut-off grades from the mine whilst delivering higher grades to the mill.Optimising flow sheets and technology performance requires detailed understanding of particle size and shape distributions as well as liberation characteristics to suit the particular separation unit, combined with knowledge of the available technologies, their capabilities and the economic impact across the whole mine cycle.CITATION:Gray, A, 2017. The role of liberation in physical separation techniques, in Proceedings MetPlant 2017, pp 147–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

Between, 1980 and 1984, the demand for non- ferrous metals in the free world grew annually by 1.5 per cent for copper, 0.4 per cent for lead, 1.4 per cent for zinc, and 2.5 per cent for nickel. The growth rate decreased substantially compared to the rate experienced before 1980, and was far lower than the GNP growth during the corresponding period. The main reasons for this are considered to be 1. resource-saving efforts by industrialized countries resulting from the first and the second oil crises, 2. saturated demand for durable consumer goods, and 3. substitution of non-ferrous metals by new materials such as optical fibers.

Jan 1, 1986

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By P Micale

Geological data provides the foundations for the mining value chain. It is used to underpin the modelling and planning and consequently optimise downstream business decisions. However, it is often forgotten or taken for granted. End users often assume the data to be sound without verification. Geological data can be considered a company’s number one asset. Subsequently, the storage, use and management of this data need careful curation and time invested in preserving and protecting it. An established polymetallic mine with 20 000 drill holes could have a data replacement value in excess of $500M at 2020 prices, excluding labour and salary costs. The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the ‘JORC Code’) provides guidelines for Public Reporting. Within the code, Table 1 requires discussion around the different types of geological data, its collection and use. What is needed is additional details regarding the validation and integrity of the geological database. A comprehensive guideline specifying minimum geological standards for geological databases has been developed. This expands on the critical points outlined in Table 1 of the JORC Code. This guideline can be used by companies where geological databases are managed in-house or used to assess these services’ outsourcing. This guideline will ensure that geological data is reliable and unadulterated and can be used with confidence. Using this guideline will assist in preserving the investment of geological data in the mining value chain

Mar 22, 2022