Search Documents

By L. B. Gittinger

Sulfur is a nonmetallic element widely distributed in nature. It constitutes 0.06% of the earth's crust but only a very small portion occurs in sufficiently concentrated amounts to justify mining. Sulfur occurs in practically all animal and plant life. It constitutes approximately 0.09% of the elements in the oceans; it has been found in meteorites. Sulfur was known and used by man before recorded history. The American Chemical Society approved spelling for the element is sulfur. The English spelling sulphur is used commercially in the United States. In ancient times, sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Sulfur is found naturally in the elemental form in subsurface deposits associated with gypsum and anhydrite in salt domes and sedimentary formations in evaporite basins and in solfatara-type deposits associated with volcanoes and mineral springs. Sulfur occurs also in molecular combination in ferrous sulfides (pyrites and pyrrhotite) and nonferrous sulfides (copper, lead, zinc, and nickel), and in mineral sulfates (gypsum and anhydrite); as hydrogen sulfide contaminant in natural gas; as organic compounds in crude oil and tar sands; and as pyrite and organic compounds in coal and oil shales. Sulfur resources are abundant and exist throughout the world but the extent to which they can be classified as reserves is greatly circumscribed by prevailing prices and technology. Estimates of world sulfur reserves are compiled by the U.S. Bureau of Mines. A compilation of reserves by area and source of sulfur published in 1970 and presented here as [Table 1] totaled 2.47 billion tons (Lewis, 1970). The effect of the decline in prices which has occurred since the earlier estimate is dramatically illustrated by the 1972 estimate of the U.S. Dept. of the Interior which shows world sulfur reserves of only 1.2 billion tons (Anon., 1972d). Sulfur is produced commercially from one or more sources in nearly 70 countries of the world. World production of sulfur in all forms totaled 41.6 million tons in 1971. (Sulfur statistics given in this chapter are long tons.) Native deposits, sulfides and oil and gas contributed, respectively, 31, 41, and 25% of world production (Table 2). Of the sulfur produced from native deposits, salt domes accounted for 54% and evaporite basin deposits, 44%. Volcanic deposits are of little significance except for local consumption. The past two decades have seen important shifts in the world's sulfur sources. In 1950, native deposits and sulfides each supplied about one-half of the world's production. During the 1950s, sulfur recovered from oil and natural gas grew rapidly, representing about 10% of the total by 1960. Since then, the petroleum industry has continued to increase its relative importance as a source of sulfur, representing more than 30% at 1972 year-end. Sulfur is generally classified as elemental or nonelemental for statistical purposes. Elemental sulfur is sulfur produced in the pure, uncombined form. It includes production from native deposits, as well as that recovered in the elemental form from oil and natural gas or other sulfur-bearing materials. When produced from other than native deposits, it is generally referred to as recovered elemental sulfur. Nonelemental sulfur is that which is utilized commercially in molecular combination with other elements, such as sulfides or sulfates. Elemental sulfur is being produced from salt dome deposits in the Gulf Coast region of the United States and the Isthmus of Tehuantepec in Mexico, and from evaporite basin deposits in west Texas, Poland, Sicily,

Jan 1, 1975

By Roshan B. Bhappu, Raul A. Deju

A method is proposed by which the chemical reactions between water and a silicate bed can be related to equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved, and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented. The knowledge of surface reactions at the water-solid interface is of critical importance in extractive metallurgy. This is especially true in regard to the froth-flotation process of mineral concentration and all phases of hydro metallurgical recovery of metals. Similarly, the problem of ground-water contamination is one of growing concern, not only because of the increasing demands on our sources of supply but also because of the increasing necessity to find vehicles of waste disposal. The hydrochemistry of waste waters must be understood to exploit and develop such resources properly. To understand these problems, it is necessary to obtain a better insight into the reactions that take place between water and a solid packed bed. To do this, we will develop here in a theoretical model that predicts the fate of a chemical species in solution as it reacts with a silicate bed through which the liquid percolates. The treatment will be one-dimensional in nature and will not include dispersion. Experiments will also be presented to substantiate the theoretical model, using the silicate minerals listed in Table 1. This paper is preliminary in nature and is part of a larger study of the surface chemistry of the silicate-water interface. Mechanism of Surface Reactions In a previous paper,' the authors discussed the properties of various silicate minerals from a mineralogical standpoint. Now efforts will be made to study the reactions that occur when these minerals are put in contact with water. The reactions occur almost entirely in the surface layer of the mineralsa and are termed sorp-tion reactions. In this study sorption denotes the composite of all physical adsorption and chemical adsorption occurring between the silicate surface and the water in contact with it. A model of sorption as seen from a chemical-bond standpoint is presented below. On the basis of this model, the surface reactions between deionized water and a silicate mineral can be studied. Sorption Model: It is known that as the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, the oxygen-to-metal bonding increases. Upon the fracturing of a silicate-mineral crystal, the oxygen-metal bond breaks more easily than the stronger oxygen-silicon bond, resulting in a negatively charged surface. Then, if the mineral is immersed in a liquid containing hydrogen ions, the negatively charged surface should tend to be neutralized by hydrogen ions from solution, resulting in a change of the solution pH. Thus, an increase in the degree of sorption of hydrogen ions must occur as the oxygen-silicon ratio in the crystal structure increases. Also in a previous paper,' the authors found that for a given silicate mineral the change of pH with time is given by

Jan 1, 1971

By W. D. Robertson, R. E. Reed-Hill

DEFORMATION of magnesium crystals in a direction parallel to the basal plane has a special significance as a result of the preferred orientation characteristic of cold worked and recrystallized polycrystalline magnesium sheet and extruded rod in which the basal plane tends to lie in or near the plane of the sheet or the axis of a rod. The principal objective of the present study is a determination of the modes of plastic deformation in magnesium single crystals in this orientation. Evidence for nonbasal slip in magnesium has been presented by a number of authors. Schmid and Was-serman&apos; indicated that pyramidal slip on {1011} < 1120> or {1012} <1120> could occur above 225°C. Bakarian and Mathewson2 stablished that the slip system {1011} <1120> operates at high temperatures and that 225°C was a lower limit for pyramidal slip. The latter authors also showed that the critical resolved shear stress for {1011} slip was 400 g per sq mm at 330°C, while that for basal slip was 66 g per sq mm at the same temperature. Thus, at 330°C basal slip should be expected for all orientations except those in which the stress axis lies almost in the basal plane. More recently Burke and Hibbard3 oserved pyramidal slip at 25°C, when the stress axis was 6" to the basal plane and 14" to a <1120> slip direction. The critical resolved shear stress for pyramidal slip was 52 g per sq mm, which is only slightly greater than their value for basal slip (46 g per sq mm). Chadhuri, Chang, and Grant4 have observed non-basal slip in creep tests with polycrystalline specimens in the temperature range 250" to 350°C. The observed slip bands, which were extremely irregular in appearance, can be explained in terms of cooperative slip on {1011} and (1010) planes which have a common slip direction. Prismatic (1070) slip in polycrystalline magnesium was observed by Hauser, Landon, and Dorn.5 It was found to occur at low temperatures (78" and 195°K) and it was accompanied by cross slip in which the cooperating plane was the basal plane. Since prismatic slip occurred only at regions of high stress concentrations, the critical resolved shear stress could not be determined. Experimental Procedure The present work was performed on crystal specimens which were all cut from the same large single crystal. The original cylindrical crystal, 0.5 x 7 in., was grown in a Bridgman type furnace in which the temperature gradient was moved past the stationary crystal in the manner described by Jillson6 and Burke.&apos; High purity magnesium was furnished by the Dow Chemical Co. with the following spectro-graphic analysis in weight percent: 0.003 pct Al, <0.01 pct Ca, 0,002 pct Cu, <0.001 pct Fe, 0.008 pct Mn, <0.001 pct Ni, <0.002 pct Pb, <0.01 pct Si, <0.001 pct Sn, and <0.01 pct Zn. The large crystal was cut into four cylindrical pieces about 1.5 in. long. A flat surface parallel to the basal plane was made by hand grinding with lubricated metallographic paper on one side of each cylinder. In order to prevent bending in subsequent cutting operations, the crystals were supported by

Jan 1, 1958

By J. C. Rengel

Why and how the nuclear industry entered the electric power generation business is discussed in terms that nuclear energy was an undoubtedly additional energy resource and that it had promise of becoming a virtually inexhaustible generating power if breeder reactors could be devised. The growth of nuclear power, its total generation capacity, are related to the need of increasing energy requirements. The use of atomic energy for power generation will grow if it can compete economically with other fuels. The rate of growth, the time scale and direction of technical development is dependent on ore supplies. It is predicted that by 1980, 50% of all new power installations will be nuclear stations. INTRODUCTION Ten years ago, the nuclear industry was virtually unborn, the Atomic Energy Act of 1954 had just been signed, and peaceful applications of atomic power was little more than a phrase. Serious discussion of the practical application of nuclear energy to electric utility installations in the West was highly unlikely. The questions: Why and how did the nuclear industry enter the electric power generation business at all?; What is the predicted growth of nuclear power?; What technological changes do we predict?; How will the above changes affect the utilities? will in part be answered by this paper. WHY NUCLEAR POWER? The only justification for the West as for any other section of the country for atomic power is economics. Whatever energy source will provide the lowest generation cost will prevail; the only electric utilities which have shown an interest in nuclear power are those to whom it means lower generation costs. It is true that the Government sponsored the development of this technology long before there was any evidence of better economics; but a Government must take a very long-range view and it is the only type of organization that can afford to look more than twenty or thirty years into the future. The Government looked at projections such as shown in Fig. 1, which shows various rates of energy consumption, and matched these against estimates of fossil fuel resources. This showed that we will exhaust our low-cost fossil fuel supplies within 75 to 100 years and our total known fuel supplies within 150 to 200 years. The decision to invest in nuclear energy rested, therefore, on two arguments: a) It was undoubtedly an additional energy resource; and b) It has promise of becoming a virtually inex-haustable resource if breeder reactors could be devised if, while generating power, the reactors would produce more fissile materials than they consumed. This decision produced an unexpected bonus: nuclear power became competitive with fossil power much earlier than had been expected and, as shown in Fig. 2, forced the coal industry to take a hard look at its own position. I believe that the drop of coal prices shown here is the direct result of the entry of nuclear power into the energy supply business. At this point, it ought to be explained why and under what conditions nuclear power can be cheaper than fossil power. Fossil fuel cost to the utility is composed of two factors: a) Mining; and b) Transportation. As a result, the cost of fossil fuel to the utilities varies from 126, 106 Btu to 306, 106 Btu and higher. Nuclear energy is highly concentrated and the transportation factor becomes insignificant. Today the cost of nuclear fuel to the utility ranges between 156

Jan 1, 1967

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe&apos;s book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe&apos;s writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe&apos;s book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe&apos;s writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By M. Kaufman, A. E. Palty

The phase structure and aging characteristics of two nickel-base alloys, Inconel 718 and 702, were investigated. Wrought and cast Inconel 718 showed ArisCb as the major hardening phase, as well as ture was positively identified. Inconel 702 had Ni3Al as the major hardening phase, as well as Cr7C3-of the phase amounts with temperature was determined. 1 HE value of phase structure and aging rate information in the utilization of alloys has been well established. As part of a continuing program, the results obtained on two nickel-base alloys, hconel 718 and Inconel 702, are presented here. Inconel 718 is a relatively new alloy considered for application in both sheet and cast form. Its novelty lies in the use of high columbium tantalum levels in a Ni-Cr-Fe base. No previous work on this type of alloy has been reported in the literature. Inconel 702 is being used now as an oxidation-resistant sheet alloy. Occasional fabrication problems spurred work on its basic structural behavior. The composition of 702 is essentially nichrome plus aluminum and titanium for strengthening and added oxidation resistance. This puts it in the basic class of other nickel-base alloys which have already been studied. The two alloys will be treated separately. INCONEL 718 Phase Study Methods. The phases present after the various conditions investigated were determined by X-ray diffraction analysis of two different elec-trolytically extracted residues and microscopic examination. The extraction methods, using 10 pct HC1 in alcohol and 10 pct H3PO, in water and the X-ray technique have been described previously.&apos; The effect of temperature on the phase behavior was studied on sheet material using the following heat treatments: 2250°F, 2 hr, ice brine quench 1300 100 hr, water quench 2250°F, 2 hr, ice brine quench 1400°, 100 hr, water quench 2250°F, 2 hr, ice brine quench 1500°F, 100 hr, water quench 2250o 2 hr, ice brine quench 1700°F, 48 hr, water quench 2250°F, 2 hr, ice brine quench 1850°, 24 hr, water quench 2250°, 2 hr, ice brine quench 2000°F, 6 hr, water quench The high solution temperature was an attempt to dissolve as many phases as possible without causing melting. Aging exposures were made longer than normal heat treating times in order to approach equilibrium conditions more closely. Cast material was examined only in the as-cast condition and with the normal heat treatment (1700°F, 1 hr, air cool 1325oF, 16 hr,air cool). Materials. The full phase study was performed on sheet specimens approximately 1/2 in. by 2 in. by 1/16 in. The cast pieces were cut from the gating system of a vacuum-cast test piece. An all weld-metal specimen was made by running many weld beads on the sheet using filler made from the sheared edges of the sheet. All external contamination was removed by belt-sanding followed by an electro-polishing treatment. The typical composition of wrought Inco 718 is as follows: The alloy is air-melted. Cast hco 718 may have higher molybdenum. Due to the expectation of finding a Ni-Cb phase (Ni, Cb) for which no X-ray diffraction pattern was available in the ASTM Index, a special 5 Ib heat to the stoichiometric composition of this intermetallic

Jan 1, 1962

By E. Hein, R. A. Dodd

The fatigue softening of prior strain-hardened poly crystalline copper has been determined by measuring changes inflow stress resulting from fatigue treatments. Tensile fatigue does not soften the metal, while the softening due to reversed stress fatigue depends on the extent to which fully reversed stressing is approached. True tensile fatigue is shown to be possible only in the case of long wire specimens. Annealing following fatiguing of strain-hardened metal shows that tensile fatigue is very effective in modifying normal recovery and recrys-tallization. OBSERVATIONS by Ludwik and Scheu,&apos; Kenyon,&apos; Polakowski and Palchoudhuri, Kemsley, and Broom and Ham,596 have shown beyond doubt that strain-hardened metals are softened by reversed-stress fatigue. To some extent the softening might be associated with a rearrangement of dislocations, but the results of Broom and Ham5 on the temperature dependency of the fatigue hardening of annealed copper, and those of McCammon and Rosenberg7 on the partial recovery at 100&apos;C of fatigue-hardened copper suggest that point defects may be involved. Since lattice vacancies are the only species of point defect present in appreciable quantities in thermody-namic equilibrium, most attention has been accorded them in the various theories advanced to explain hardening and softening effects resulting from fatigue. Precise mechanisms remain uncertain, and while some effects may be due to single vacancies, defects arising from vacancy clusters may also contribute to the changes in properties. All types of plastic deformation result in point-defect formation, one frequently invoked formation mechanism involving the nonconservative motion of jogs formed by the intersection of, for example, mixed dislocations. But since fatigue deformation is thought to be a particularly effective way of forming point defects, additional mechanisms peculiar to fatigue must be sought. One possibility is that jogged loops contract during the unloading cycle to give rows of vacancies. A local high-vacancy concentration could conceivably promote polygonization and recovery by climb, and, therefore, could explain the fatigue softening of strain-hardened metals under appropriate conditions of temperature. Conversely, the experiments by Broom and Ham6 on the fatigue hardening of copper single crystals involving subsequent tensile testing of previously fatigued specimens, resulted in the observation of distinctly lowered yield points. This could be due to vacancy atmospheres associated with dislocations, possibly augmented by jogs on dislocations. In addition to the yield-point phenomenon, a post-yield hardening was observed, with a temperature-dependence resembling the friction-hardening of irradiated metals,9 this again suggesting a point-defect mechanism. An important development in this field has been the observation,10 by transmission electron microscopy, of high concentrations of prismatic loops in fatigued aluminum. By analogy with quenched aluminum filmso11 it seems certain that these loops originate in the collapse of vacancy clusters formed during deformation. Metals, such as copper, having a relatively low-stacking fault energy would tend to produce Frank sessile loops (in practice tetrahedral defects with stacking faults on all (111) planes) rather than the glissile prismatic loops observed in aluminum. The manner in which these various defects affect the different aspects of fatigue behavior has not yet been fully investigated. The present work was designed principally to indicate whether tensile fatigue gives rise to hardening and softening effects similar to those associated with reversed stress fatigue, and with the hope of providing additional information on the contribution of point defects to fatigue deformation. Despite the uncertain ty often associated with the interpretation of resistivity data, i.e., the relative contribution of stacking faults and other defects, such measurements are conveniently employed to study point defect pheno-

Jan 1, 1962

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By O. J. Neslage, R. W. Jenkins

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today&apos;s wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By G. P. Marino

The "conductivity ", Kr, of a spherical void in a linear temperature gradient due to radiation is calculated by integration of the general expression for diffuse radiation between two gray surfaces of arbitrary orientation. The spherical geometry allows an exact evaluation of the phenomenon without resorting to up-proximate expressions for the radiant heat flux. The resulting expression for Kr is three quarters of the approximate value obtained by Loeb. IN the determination of the thermal conductivity of porous materials such as sintered UO2 and ThO2 fuel pellets, the magnitude of the thermal conductivity in the pores due to radiative heat transfer across the pore, Kr, may be important in assessing the total conductivity of the pellets. Loeb&apos; has calculated Kr for various pore geometries by approximating the net flux of heat between two surfaces of temperature difference AT as 4eT~AT and obtained: K,=4yoet3odp [1] where a is the Stefan-Boltzmann constant, E is the emissivity of the radiating surface, To is the average absolute temperature of the region across which radiation occurs, dp is the largest dimension of the gap in the direction of heat flow, and y is a geometric factor. That is: y = 1 for laminar pores and cylindrical pores with axes parallel to the heat flow direction, y = 2/3 for spherical pores, y = /4 for cylindrical pores with axes perpendicular to heat flow direction. It was the purpose of this work to obtain an exact expression for K, in spherical pores by integration of the general expression for the net heat transfer between two incremental areas on the surface of a spherical pore. This procedure yields a value of Kr 3/4 of that obtained by Loeb. I) CALCULATION OF Kr Fig. 1 illustrates the general geometry which defines the problem. The total emissive power for a gray body is given by: E = EoT4 [2] where E is the radiated energy per unit area of the radiation surface per unit time, T is the absolute temperature, o is the Stefan-Boltzmann constant (o = 5.67 X lo- &apos;&apos; watt per sq cm-"K1), and E is the emissivity of the surface. Although Eq. [2] gives the exact expression for the total emissive power of any gray body, all practical problems involve the net exchange of thermal radiation between a body and surrounding bodies. The two major considerations in the solution of such problems are a) shape and relative position of the surfaces and b) the emissivities of the surfaces. In this work it shall be assumed that all incremental areas on a pore have the same emissivity and, further, that little or no reflection occurs (i.e., the radiation hitting a surface is either absorbed or transmitted). Thus, the solution of the stated problem requires only that consideration a be satisfied. Consider two incremental surface areas dA 1 and dA2 of the same material in a general orientation to one another. Let dAl be at temperature TI and dAz be at T2. Fig. 2 illustrates the geometrical parameters involved. That is, 71, is the normal of dA, n2 the normal of dA2, r the line connecting the centers of each area, 81 the angle between nl and r, and Q2 the angle between 7,2 and r. Using Eq. [2] and the Lambert cosine law of diffuse radiation it is easily shown that:293 WdAf- dA, = ecr T*------^fpi------" dAidA2 [ 3a 1 and

Jan 1, 1970

By R. W. Jenkins, O. J. Neslage

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today&apos;s wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By J. S. Aronofsky

The results of polentiometric model studies and numerical computations are described. The purpose of these studies was to determine the influence of the mobility ratio on flooding efficiencies during water encroachment in petroleum reservoirs, in systems of regular well geometry. The direct line drive well pattern having relative spacing distances of one and one-half to one was investigated for water to oil mobility ratios of 10. 1. and 0.1. The results of these studies indicate that the pattern Sweep efficiency i.; very dependent upon the mobility ratio. INTRODUCTION The almost universal occurrence of water in the immediate neighborhood of oil-hearing sands lends considerable emphasis to the desirability of having a rational analysis of water encroachment into petroleum reservoirs. This problem has 1)become increasingly important with the accelerated use of water injection for secondary recovery operations. The water encroachment problem has been studied from both the theoretical and experimental viewpoints by Muskat.&apos; He has formulated, in a precise manner, differential equations to express flow in a water encroachment system, and rigorous analytical solutions have been developed for the linear, radial, and spherical cases.&apos; However, it becomes exceedingly difficult to solve the encroachment problem rigorously for any general two-dimensional system in which the shape of the two-fluid interface is not immediately evident from the geometry of the system. The difficulty lies in the fart that a rigorous analytical solution requires that the shape of the two-fluid interface be known simultaneously with its instantaneous posititon and with the pressure distribution on both sides of the interface. Although this paper concerns the study of the two-fluid system of oil and water. the methods described in the paper are generally applicable to other systems of incompressible and immiscible fluids in which the displacing fluid sweep-the displaced fluid down to a residual value. In each region it is assumed there is only one mobile fluid and its mobility is constant throughout the region. The Same procedure. with minor alteration, is applicable for gas injection systems provided the assumption can be made that both the displaced and displacing gases can be described by steady state formulas. For the particular two-fluid problem considered in this paper, there is a relative permeability. K, and a viscosity. p. associated with the water zone, and a different permeability and viscosity associated with the oil zone. The K/p (mobility value associated with a particular volume element of the porous medium. at any instant of time. will depend upon whether the element is ahead of. or behind the advancing interface. It is assumed that all volume elements ahead of the interface are characterized by the K/p value for oil, while all the elements behind the interface are characterized by the K/p value for water. That is. the K/p value in the oil zone is constant throughout the oil zone. and the K/p value in the water zone is also constant but different from the value in the oil zone. The symbols are defined at the end of the paper. The well pattern chosen for initial study is the direct line drive; the swept-out area at breakthrough was determined by two different methods which are described in the section on theory. These are: 1. Potentiometric analyzer 2. Numerical computation The use of the potentiometric analyzer for studying water flooding problems is adequately described in the literature, particularly for cases where the mobility in the water zone is assumed equal to the mobility in the oil zone." &apos; 5

Jan 1, 1952

By M. R. Tek, M. L. Katz

The flow of fluids in stratified porous systems, in which adjacent layers of the system are in communication over part or all of their common interface, in many instances involves crossflow between layers. A theoretical study has been made of the unsteady-state flow of slightly compressible fluids during depletion of bounded stratified porous systems. Consideration has been restricted to single-phase flow, with negligible capillary and gravity effects. Analytical expressions have been derived for pressure distribution and for (luxes at the producing face in two-layer systems with complete fluid communication between layers. These expressions occur in the form of double Fourier and Fourier-Bessel series. The method of extending the solution to any number of layers is demonstrated by deriving the equation for pressure distribution in a three-layer system. On the basis of the exact results for two-layer systems, certain generalizations regarding the behavior of stratified systems in general are presented. The performance of stratified systems, in terms of cumulative flux as a function of time, is shown to lie at all times between bounds established from single-layer theory. The upper bound is given by treating the system as a single layer with arithmetic average physical properties. The corresponding lower bound is the summation of the fluxes from each layer as treated individually. Variation in performance of stratified systems between the upper and lower bounds is determined by the extent to which crossflow occurs in the system. The principal parameters affecting the amount of crossflow are the vertical permeability of the system, the ratio of system thickness to "radius of drainage" and, for radial systems, the ratio of system thickness to interior radius. At very early times, the system performance is near the lower bound. As time and the radius of drainage increase, the per- formance tends toward the upper bound. INTRODUCTION One of the principal problems confronting the reservoir engineer today is the incorporation of the effect of reservoir heterogeneity into predictions of reservoir performance. The first part of this problem is the characterization of the actual reservoir heterogeneity in a mathematically useful manner.1, 2 It is then necessary to calculate the effect of this heterogeneity on the system performance. It is frequently possible to estimate this effect by comparison with the known behavior of an idealized system. One such idealized system is the stratified or "layer-cake" model. Many studies have been made of the behavior of stratified systems, from both a theoretical and experimental standpoint. The great majority of the theoretical studies have been concerned with systems of separated layers, with no fluid crossflow. Among the more noteworthy of such theoretical papers is that recently published by Lefkovits, et al,3 in which a comprehensive analysis was presented for the behavior of bounded stratified systems which are unconnected except at the wellbore. Three recent references have dealt with stratified systems including the effect of crossflow. Jacquard4 has presented mathematical derivations pertaining to depletion of two layer systems producing at constant rate. A doctoral dissertation by Katz5 contains analytical solutions and tables of results for pressure distribution and fluid flux during constant-terminal-pressure depletion of two-layer and three-layer systems with crossflow, together with tables of eigenvalues necessary in the computations. The dissertation also presents results from experimental studies of stratified systems using a heat-transfer analog model. This paper is largely based on the material in this dissertation. A third paper has been presented by Russell and Prats6 since completion of the work resented herein, containing mathematical derivations for and discussion of the behavior

By A. G. Jordan, W. Jeitschko, Paul A. Beck

The occurrence qf the V phase structure /Zr,Co,Ge, type) in ternary syste7ns (titanium, zivconium, niobium, lanta1urn) -(nickel, cobalt, iron)-(silicon, germanium) was incestigated. Nine V silicides and four V gertrlanides were found and their lattice constants are reporled. The lattice constants of twenty-one preri-ously identified E phases (TiNiSi type) are given. The average atomic volumes of these phases are discussed in relation to similar binary phases. ThE occurrence of a phase Ti4Ni4Si7 was first reported by Westbrook. DiCerbo, and peat&apos; who gave it the name "V phase". They also reported the existence of an E phase TiNiSi. Subsequently a systematic study was undertaken in this laboratory to explore the occurrence of E&apos; and V phases3 in related ternary systems. In the meantime the crystal structure of the E phase TiNiSi 4 and of the V phase Zr4CO4Ge 75,6 was determined. In the present paper the details of the V phase investigation and the lattice constants of the E and V phases are presented. V PHASES Alloy specimens of approximately 10 to 15 g were prepared by arc melting under argon (99.996 pct Ar) atmosphere. The starting materials were all of purity higher than 99.9 pct, with the exception of cobalt. which contained 0.14 pct Fe as the only major impurity. The weight losses were in all cases less than 2 pct, in most cases less than 1 pct. The samples were encapsulated in fused silica tubes with sufficient argon to yield about 1 atm pressure at the annealing temperature. After the homogenization anneal. Table I. the specimens were water-quenched. A representative portion of each specimen was then examined metallographically (etchant: 20 pct HNO,. 10 pct HF. 25 pct glycerine, 45 pct H20). Only minor amounts of second- and third-phase particles were observed in the specimens listed in Table I, with the exception of alloys Zr4Fe4Si7 and Ta,Fe,Si,. which contained an estimated 10 pct by volume of foreign phases. X-ray powder photographs were taken with a Seeman-Bohlin type focusing camera and Fe-KO radiation. Of the thirty possible combinations of elements in the ternary systems (titanium, zirconium. vanadium. niobium. tantalum)-(iron. cobalt, nickel)-(silicon. germanium) thirteen V phases could be identified. In the remaining seventeen ternary systems and also in the systems Cr-Ni-Si and (M0.W)-(Ni.Co)-Si no V phase was found at the composition 4:4:7 after annealing at temperatures between 900" and 1200&apos;C. For the determination of the lattice constants of the V phases Debye-Scherrer photographs were taken using the asymmetric film arrangement and CrKcr radiation (ka1, = 2.28962A). Using the positional parameters, as determined6 for Zr,Co,Ge,. Table 11. intensity calculations were carried out for each of the V phases with the aid of a computer program.: Thus unequivocal indexing of the diffraction patterns was greatly facilitated. The lattice constants. Table I. were then computed by a least-squares fit of the high-angle lines with f (0) = cos2 Q as extrapolation function. Only few. if any. very weak impurity lines were observed, with the exception of the three iron alloys Zr,Fe,Si7. Zr4Fe,Ge7. and Ta,Fe,Si7. The agreement

Jan 1, 1970

By B. B. Rath, Hsun Hu

Rates of migration of large-angle boundaries have been studied in zone-refined aluminum crystals, defonned 80 pct by rolling in the (110)[112] orientation at -78°C followed by a recovery anneal at 80°C. Artificially nucleated grains show a marked variation. by an order of magnitude, in their growth rates in different directions. The average activation energy for the migration of all boundaries was found to be about 16,000 cal per mole. The anisotropy of the boundary migration is rationalized on the basis of the boundary structure. It has been observed by Beck and HU,1 Kohara el al,2,3 and Czjzek and Haessner4 that recrystallized grains formed upon annealing Of deformed sing1e crystals of aluminum show anisotropic growth characteristics. Kohara et al. found that single crystals rolled in the (110)[112] orientation, when random nuclei were provided on one side of the crystal by rubbing with emery paper and annealing, developed a sharp recrys-tallization texture on the other side of the crystal upon further annealing. This sharp recrystallization texture consisted of four components, which were related to the deformation texture of the crystal, i.e. (110)[112], by rotations of ±40 deg around each of the two common [ 111] axes&apos; They also noted that recrystallized grains were elongated in directions perpendicular to either of these two common [1111 axes. They attributed this anisotropic growth to the difference in the rate of self-diffusion or diffusion of impurity atoms along the tilt and the twist boundaries. A somewhat similar investigation was conducted by Czjzek and Haessner4 On strained single-crystal sheets Of alum- inum. These authors claimed that the matrix structure of the deformed crystal had a greater effect on the growth anisotropy of the recrystallized grains than did the boundary orientation itself. In the present investigation quantitative measurements of the rate of grain boundary migration in anisotropic growth have been made in zone-refined aluminum (99.9999+pct pure) crystals deformed 80 pct by rolling in the (110) 112] orientation. Crystals of this particular orientation were chosen because of the following desirable features: 1) the crystal does not change its orientation during rolling; 2) the rolling plane contains all the significant crystallographic directions; and 3) when annealed, following deformation, the crystal does not re-crystallize spontaneously but polygonizes to a stable and homogeneous structure. Hence, the initial orientation of the crystal and a constant strain energy in the matrix can be maintained during subsequent grain boundary migration studies. It is essential to keep the driving force constant for the study of boundary mobility.5 EXPERIMENTAL PROCEDURE A cylindrical single crystal of 1 in. diam was grown by the Bridgman method in a high-purity graphite mold. The resistance ratio, R(4.2°K) /R(298°K) , of the grown crystal was approximately 2.0 x 10-4. A number of slices, 1/4 in. thick, were cut from the crystal along the (110) plane and were mechanically and electrolyti-cally polished to remove the strained surface layer. The crystals were then rolled along the [112] direction to 80 pct reduction in thickness at -78°C. To minimize surface friction, the crystals were rolled between two layers of 0.005-in. teflon sheet. Rolling was interrupted, prior to completion, to remove the surface layers and the edges by electropolishing. These and similar precautions in handling the rolled crystals

Jan 1, 1967

By F. C. Schora, H. P. Meissner

Both a graphical and an analytical technique are presented for calculating stream compositions and temperatures in adiabatic staged systems in which solids travel countercurrently to a gas stream. Such a system might be a tower containing several plates, on each of which the descending solid is fluidized by the rising gas stream. Examples are presented in which chemical reactions occur, including the oxidation of SO, by a solid catalyst and the gaseous reduction of iron oxides. COUNTERCURRENT staged processes involving reactions between solid and gas streams are becoming more common. These operations are generally carried out in a series of beds of fluidized solids, with each bed or "plate" acting as a stage. Fig. 1 is a schematic diagram of such a series of stages located in a column, down through which a solids stream moves from stage to stage counter to a rising gas stream. Typical reactions carried out in such systems are the dehydration of aluminum trihydrate, the calcining of limestone, and the gaseous reduction of iron oxides. Calculation of the performance of these counter-current systems rapidly becomes more complex with increases in the number of stages and in the number of chemical reactions occurring. Calcula-tional procedures for isothermal operations of such systems have been described.4 Actual tower operations, however, are generally adiabatic, and in consequence far from isothermal. The object here is to present both graphical and analytical techniques applicable to such adiabatic towers operating continuously and in steady state. In this introductory discussion, the graphical techniques presented are of the McCabe-Thiele type, rather than of the Pon-chon type. In all the examples presented, it will be assumed that both thermal and chemical equilibrium are attained in each bed. The assumption that the gas and solid streams leaving each bed are at the same temperature as the bed is in accordance with the familiar behavior of actual fluidized solid systems. Chemical equilibrium, on the other hand, is not necessarily attained in any given stage between these two streams, even with deep beds, since reaction rates may be slow. In the last section of this paper, discussion is presented of methods suitable for use when chemical equilibrium is not attained. The adiabatic tower in Fig. 1 has "n" stages numbered from 1 to n, starting with the bottom stage as number 1. In analyzing this tower&apos;s performance, it is important to express gas flow rates in terms of a key component or element which remains completely within the gas stream throughout the tower. Similarly, solid flow is best expressed in terms of a key compound or element which remains within the solid phase throughout the tower. Thus, in burning limestone with a hot flue gas, the gas flow might be expressed as G, the pound mols of nitrogen flowing through the tower per unit time, while solid flow might be expressed as S, the pound atoms of calcium in all forms in the solid stream per unit of time. Defined in this way, both G and S are constant throughout the tower. The enthalpy of the gas and solid streams are now best expressed in terms of these key components. That is, the gas stream enthalpy H is expressed as Btu in the total gas per mol of the key component in the gas. Similarly, the solids stream enthalpy h is expressed as Btu in the total solid stream per pound mol (or pound atom) of the key component in this stream.

Jan 1, 1962

By F. D. Rosi, C. A. Dube, B. H. Alexander

WHEN a deformed polpcrystalline metal is heated to a sufficiently high temperature, a recrystallized structure develops which consists of small, essentially stress-free grains. This transformation is referred to as primary recrystallization. Under certain conditions, on prolonged annealing of the specimens, a type of grain coarsening occurs in which a small number of grains commence to grow at various points by devouring the neighboring finegrained primary structure, which, in itself, exhibits a marked stability toward normal grain growth. This grain coarsening process has been referred to by Burgers&apos; as "secondary recrystallization" or "exaggerated grain growth." Although much work has been done on recrystallization and growth processes, present knowledge of the factors which determine the occurrence and growth of secondary grains is inadequate for the advancement of a theory which accounts for the observed characteristics of this recrystallization phenomenon. In this respect, it would be important to make measurements of the velocity of growth of these large secondary grains. The early work of Feitnecht2 on aluminum showed that the size of secondary grains increased with temperature and time, suggesting that such measurements would be possible. More recently, Burgers1 found that the growth velocity of these grains in aluminum was constant over a large time interval, as is generally found for the growth velocity of primary grains in a uniformly deformed test piece.3-5 It is reasonable to expect that the determination of the activation energy of the secondary growth process might lead to a better understanding of the underlying atomic mechanism. This investigation, therefore, is one of a series primarily designed to measure the growth velocity of secondary grains at various temperatures for silver, copper, and aluminum. It is hoped that these studies along with those of orientation relationships, will establish a sound basis for theorizing as to the origin and nature of the secondary transformation. Experimental Procedure The metal used in the present investigation was high-purity silver (999.9 fine), which was supplied in the form of cold-rolled plates 0.250 in. thick. These plates were annealed at 500°C for 1 hr and then straight-rolled to a thickness of 0.04 in. in three reductions of approximately 45 pct, followed in each case by an anneal at 450°C for 1/2 hr. The 0.04 in. sheets were given a final reduction of approximately 50 pct, which resulted in a thickness of 0.02 in., thereby insuring two-dimensional crystal growth. Individual specimens of this material about 1x3 cm were used for all heat treatments, unless otherwise noted. The annealing was carried out under an atmosphere of argon in an Inconel tube furnace whose temperature was controlled to within -+2°C. Metallographic examination of the secondary transformation was accomplished by mechanically polishing the specimens on one side to approximately one half their thickness through 2/0 metallographic emery paper, and then electrolytically polishing in a solution of potassium ferrocyanide and sodium cyanide. With a current density of approximately 20 amp per sq dm, the time required to obtain a satisfactory surface varied from 3 to 5 min. Standard potassium bichromate was used to etch the electrolytically polished surfaces. A heavy etch with this solution produced a sharp contrast between the secondary grains and the fine-grained primary structure, darkening the latter while leaving the large secondary grains bright. All area measurements of the secondary crystals were made with a planimeter on enlarged tracings of the grains.

Jan 1, 1953

By L. R. Page, J. J. Norton

EFFECTIVE methods for determining grade and reserves of pegmatites in advance of mining have been developed in recent years. When intensive work began on the economic geology of pegmatites during the early years of World War 11, it was widely believed that grade and reserves could be estimated only in a most general way. The literature indicated that not all pegmatite deposits are unpredictable, but statements emphasizing unpredictability and irregularity seem to have been more widely accepted. Many standard references reflect the prevailing opinion that minerals: are unsystematic in their occurrence in pegmatites. Pegmatites have been described as "notorious for their irregular structure," and minerals within pegmatites as "irregularly distributed." "irregularly disseminated," of "erratic occurrence," "proverbially erratic in distribution," "characterized by extreme irregularity in ... size and distribution of the essential minerals, and variety and proportion of the accessory minerals," and "spotty.&apos;"" Over many years, however, geologic techniques have been applied with increasing success to economic analysis of pegmatites. Investigations, chiefly since 1939, have shown that mineral distribution and structure of pegmatites are largely systematic and that detailed geologic study can be used to predict the size and shape of mineral deposits in pegmatites. Because the writers are most familiar with the pegmatites of the Black Hills, S. D., examples cited are from that area." Pegmatites mined in other dis- * All examples are described more cornpletely elsewhere.: tricts are similar to those in the Black Hills," and the techniques described here have been applied by geologists and engineers working in other districts. In actual practice few pegmatite mine operators attempt to make accurate estimates of grade and reserves in advance of mining. Many deposits are too small for mining except on a very small scale; few pegmatite mines have more than ten employes. Hence there is little systematic preparation for mining, and the capital outlay may be so small that only a general knowledge of reserves is necessary. Technical personnel are rarely employed by pegmatite mine operators to make such estimates. In the future, however, as capital outlay becomes larger, estimates of grade and reserves will have to be more accurate. Geologic Aspects of Determining Grade and Reserves Estimating grade and reserves requires that the type of pegmatite, the size and shape, and the internal structure be determined by detailed geologic mapping and careful mineralogic study. The wide variations in the texture and distribution of minerals within many pegmatite deposits make a thorough geologic study of this kind necessary before it is possible to decide what sampling methods should be used to determine mineral content or grade. Types of Pegmatites: The first step in economic appraisal of a pegmatite is to determine the min-eralogical and structural type. In general, pegmatites may be classified into two groups: 1) those in which component minerals are more or less evenly distributed throughout the entire body and show relatively minor variations in texture, and 2) those in which component minerals have been segregated into units with recognizable differences in texture, mineralogy. or both. Johnston" has classified these types of pegmatites as homogeneous and heterogeneous, respectively. Cameron et al.10 have used the terms ~inzoned and zoned for similar types. The difference between the homogeneous and heterogeneous types is of great commercial importance. Homogeneous pegmatites can seldom be mined where the products are concentrated by the hand methods now commonly used, but they have been mined in a few places where a milling process has

Jan 1, 1957

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and It is now thought1&apos; that the "{0,1,13)" habit reported for the Fe-Ni-C alloys&apos;&apos; is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove. The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics and reduce to the unit tensors and j so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963