Search Documents

By William A. Johnson

The mathematical analysis of diffusion curves in solid metals is carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. Experimental Procedure If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

THIS paper describes the application of amine flotation to a specific problem-that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. SAMPLES Two samples, designated "minus 100mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.1 per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1945

By Ivor Jenkins

Processes employing 'controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,' but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By Ivor Jenkins

Processes employing 'controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,' but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By F. L. Robertson, C. H. Bacon, J. W. Till

A description is given of the development of a process for making low sulphur steel on furnaces fired with 2 1/2 pet sulphur oil. Slag and metal are analyzed at melt. Slag weight is estimated. A simple method for calculating necessary lime additions for making 0.025 and 0.035 pct sulphur steel is given. DURING the last 15 years John Summers & Sons have been confronted increasingly by the problem of producing a low sulphur steel from high sulphur materials. The principles adopted, the processes used, the data collected on a furnace specially set aside to study this problem, and speculation on future developments are dealt with in this paper. This study is limited to two melting shops which make sheet steel only, of the following analysis: C, 0.06 pct; Mn, 0.33; S, 0.04, 0.035, 0.03, and 0.025; and P, 0.02 and 0.015. All the processes described have reference to the manufacturing of this steel and are not necessarily applicable, without modification, to other steels. The raw materials used are given in Table I. Development of Process About 1934, Schenck's work on phosphorus was applied to frame quantitative rules for the removal of phosphorus, with great success. We could however, neither in our own work nor in the voluminous literature, find any assistance to frame quantitative furnace rules to remove sulphur. Perhaps, we should have persevered with Schenck's outstanding chapter on sulphur in The Physical Chemistry of Steelmaking, but we missed the importance of one (Ss) sentence on p. 478. "Evidently this ratio -------- is [S] the important quantity to be considered from the point of view of chemical reaction; it is clear that the sulphur content of the steel alone, as frequently given in the literature cannot suffice for judging the success of the reaction unless special details are given regarding the sulphur charge and the amount of slag."' We were not however very successful in getting values for Schenck's "n" that agreed with (S) arrived at by our direct analysis. [S] In addition to Schenck's work much attention was given to V value. The formula selected for V was: (SCaO) — 1.57 (2 P2O5) (S SiO2) After plotting many charges a curve was obtained, based upon the relationship between the percentage sulphur in the finished steel and V value, Fig. 1. For a long time this was used as standard with about a 60 to 70 pct success on producer-gas fired furnaces, if all uprising scrap was used and no bought scrap used. An inspection of this curve shows clearly that it is not a quantitative manufacturing process, and that it was not sure enough to go to the trouble and expense of doing stage analysis for P,O,,

Jan 1, 1952

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general. our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2-by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn ;7± MnO + Fe [A] slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aFPI OFeO ? aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term aFe may he combined with K" to give a new constant K'. Making these changes.

Jan 1, 1942

By Michael Tenenbaum

THE importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1947

By John P. Bryant

Plant nutrients are obtained by plants from both the air and the soil. Carbon dioxide, a gaseous form of carbon and oxygen, supplies the carbon which usually makes up 50% or more of plant structure. Plants are capable of absorbing carbon dioxide directly from the air. Most of this nutrient comes from the air, although some carbon dioxide is absorbed by soil water and taken into the plant as liquid. Growing plants use more water than any other substance. Plant nutrients in the soil dissolve in soil water; soil water entering the plant carries nutrients into the plant structure. Water is then given off into the air as the plant breathes or transpires. The inorganic or mineral portion of the nutrients which plants require comes from the soil. Inorganic or mineral composition of plants is usually less than 5% of their weight, and this mineral requirement, usually lacking in the soil, must be provided by fertilizers. Proper fertilization of a soil to improve its mineral level and productivity is the basis for the fertilizer industry (Thomas, 1960). There are 13 essential plant nutrients which often must be added to soils or plants and are generally considered as fertilizer minerals. These nutrients are divided into the categories: primary minerals (nitrogen, phosphorus, potassium); secondary minerals (calcium, magnesium, sulfur); and micro or trace minerals (boron, iron, manganese, copper, zinc, molybdenum, chlorine). Further, cobalt is often added to fertilizers. Although it is not considered to be an essential plant nutrient, it is essential to animal health and is often applied to forages as a fertilizer constituent. One point of major significance to the fertilizer industry is that not all nutrient carriers supply that nutrient in a chemical form which will be available to the plant. Thus, a product which may be considered a fertilizer mineral may require substantial processing or treatment before it becomes useful as a nutrient carrier. Fertilizer Industry Scope Until about 1900 demands for higher crop yields were met simply by bringing new agricultural lands into cultivation. Since that time great progress has been made in increasing yields through fertilization and improved varieties and cultural practices. The importance of the fertilizer industry to the economy and welfare of the U.S. is widely recognized. [Fig. 1] illustrates the relationship of lime and fertilizers to crop yields. In terms of tons of fertilizer products, the growth of the industry has been phenomenal, particularly between 1950 and 1970. Table 1 shows the increase in fertilizer usage. Primary Plant Nutrients in Fertilizers Primary minerals (nitrogen, phosphorus, potassium) are designated as such because of their significance to plant growth. Practically all soils are deficient in both nitrogen and phosphorus, and most of them are also deficient in potassium. Consequently, these nutrients

Jan 1, 1975

By J. Visman

A simplified method of assessing the characteristics of a cleaning unit, including washability curves, yield figures, ash error, separating gravities, and error curve. FOR more than 25 years evaluations of coal cleaning units have appeared in many publications, and during this time considerable progress has been made in developing the theory and techniques of calculating washery results. A variety of characteristics have been defined over the years, many receiving general recognition during the first post-war Coal Preparation Conference in Paris in 1950. Coal preparation has become a science, and the approach to preparation problems is being revolutionized. Formerly, for example, if a coal operator wanted to know the performance of a given cleaning unit for a particular grade of his run-of-mine, he either shipped a carload to the manufacturer for a test run or relied on a report of a test carried out on a coal similar to the one he intended to clean. In modern practice the expensive, time-consuming test work generally can be avoided if the washability curves of the coal in question and the error curve of the cleaner are known. Normally a guarantee can be given on the strength of this information. General acceptance of modern standards has thus reduced the need for pilot-scale models of existing types of coal cleaners. Needless to say, the method requires exhaustive and accurate information on the cleaning unit and on all the additional circumstances affecting its results, information that ultimately can be secured only from actual tests made in the laboratory or in the washery. It is not the purpose of the present discussion to compare the merits of various characteristics, but to describe the general method of calculation, including a method of obtaining data with a minimum of laboratory work. All data presented here were derived from tests made at the plant with portable field equipment, using small quantities of varsol, carbon tetrachloride, and bromoform. It will be explained later that the use of standard fractional ash contents designated normalized ash contents aids considerably in reducing the routine testing of coal cleaners. Like any other statistical procedure, this method has limitations, and it is not recommended for any work in connection with guarantees. Even a varying commodity such as coal, however, will follow the law of large numbers, which is the basic law of statistics, thus allowing simplification of test work without appreciable loss of accuracy. The characteristics needed for evaluating cleaner performance are normally derived from a float-sink analysis of samples of the clean coal and the refuse, followed by ash determinations of the various fractions. Usually a sample of feed is also collected to find its ash content and to make a single specific gravity cut, both in connection with determination

Jan 1, 1955

By Joseph E. Worthington

Many thousands of years ago when our earliest ancestor first swung out of a tree, picked up a rock, and threw it at what he hoped might be his lunch, the minerals industry, in a manner of speaking, was born. It was then a very long step indeed to the primitive metal industry of our early civilizations, for we know that precious metals were accumulated and some metal objects were produced several thousand years ago. Prospecting, or "exploration" to use the modern euphemism, consisted of little more than outcrop examination and the use of a gold pan, and it probably did not change much from our earliest civilizations until relatively recent times. In a general sense, all the early explorers of North America were also prospectors, for mineral wealth was certainly one of the goals of the first pioneers and settlers. The earliest pioneers didn't do too badly either, for they discovered copper and iron in various places in the Appalachians and Michigan, gold in the Southeast Piedmont and many mineralized areas in the Southwest. In most places these were outcropping ores or gossans, and the prospecting was incidental to the arduous task of ekeing out a living in a new land. It was the explosive discovery of rich placer gold deposits at Sutter's Mill in California that caught the public fancy and precipitated the establishment of prospecting as a full-time occupation. After the end of the Civil War in 1865, full-time prospecting became an important occupation and continued as such for almost three generations. Prospectors equipped with picks, shovels, gold pans and four-footed transportation swarmed all over what are now our Western States, discovering thousands upon thousands of mineral showings-and certainly most of today's large mining districts. Our vigorous western mining industry is a tribute to the courage and persistence of these men. The techniques of these picturesque prospectors, however, were essentially the same as those of their predecessors-examination of every outcrop and assiduous use of the gold pan. The great increase in discovery at this time was therefore due to increased activity rather than to different techniques. An important result of this in- creased prospecting was the growth of interest in geology. It was during this period that the U.S. Geological Survey began to grow. Many of the major mining districts were mapped, and geological studies and projections began to have an impact on further ore discovery. Ore search and development gradually became more geologically oriented and the geologist became a fixture in most mining camps by the 20th century. The development of mass-mining techniques in the early part of the century also changed exploration concepts.

Jan 1, 1971

By B. Paul, C. C. Fu

Experiments indicate that the fatigue limit of various drill steels becomes vanishingly small in the presence of water and other corrosive liquids. Therefore one must generally expect fatigue failures of drill steels in a great many field operations. However, it is theoretically possible to so choose the hammer impact speed of a percussion drill in order to maximize the total length of hole drilled before failure occurs. In this paper the existence of an optimum speed is demonstrated and it is shown to be comparable to presently used piston speeds. The influence on drilling speed and hole length of a number of other pertinent design features, such as bit geometry, hammer geometry and steel properties is also established. Although machinery should be designed to obtain optimum performance, it is not always clear just what performance characteristic is to be optimized. For example in a rock drill it would be desirable to optimize all of the following characteristics: drilling speed, bit life, steel life, total length of hole drilled before failure, and efficiency of energy conversion. The word failure could signify excessive bit wear, bit fracture, steel fracture, or some other type of component failure. It is not possible in general to optimize all performance criteria simultaneously. For example, one could achieve fantastically large drilling rates at the expense of bit or steel life, energy requirements and physical size of system. It therefore becomes necessary to compromise requirements in order to achieve a well-balanced albeit non-optimum design. It is, however, extremely useful to explore the interrelationships between the different performance characteristics. Such a procedure would help to establish theoretical limits of performance within the framework of existing knowledge and also serve as a practical design procedure for special applications where a particular performance characteristic is of greatest concern to the user (e.g., steel breakage might be especially undesirable in certain locations). It is the purpose of this paper to examine the problem of how one may drill the deepest possible hole before breakage of the drill steel occurs. Of course the problem is almost trivial if a well defined fatigue limit (endurance limit) exists for the drill steel. In such cases one merely keeps the piston impact speed sufficiently low to insure that the stresses in the steel never exceed the fatigue limit, thereby achieving an infinite life. If, however, no definite fatigue limit exists, as seems to be the case in the presence of even mildly corrosive agents such as water (see later discussion), then a finite life is inescapable and one can at best hope to maximize the useful life of the system. Indeed it will be shown that the system life is related to drilling speed in the manner shown schematically in Fig. 1-a. Even if a definite fatigue

Jan 1, 1965

By F. J. Dunkerlery, V. Damiano, J. Fulton, F. Pledger

Grain-growth and recrystallization characteristics of a commercially pure zirconium prepared by the iodide process are reported. Grain growth from 640° to 800°C was continuous once initiated and obeyed D = kt". Recrystallization of zirconium occurred at temperatures of 450° to 550°C after deformations of 20 and 50 pct. Hardening from partially soluble inclusions prevented determination of the absolute rates of recrystallization, but the relative rates of recrystallization obtained are useful as a guide in fabrication practice. BASIC information needed as a guide in the hot and cold working and annealing of metals includes recrystallization and grain-growth data. A search of the literature revealed no such information for pure zirconium. This is a report of practical grain-growth and recrystallization results obtained for a commercial grade of pure zirconium on a project sponsored by the Office of Naval Research. In this work, isothermal grain-growth curves were obtained at five temperatures from 640" to 800°C inclusively; while recrystallization curves have been determined at 450°, 500°, and 550°C for the metal at the deformation levels of 20 and 50 pct. In addition to the usual variables of temperature, time, and deformation, distribution of the second phase found in all commercial grades of iodide zirconium is also treated as an important factor in these grain-growth and recrystallization studies. In conducting this work, two properties of zirconium were particularly pertinent in dictating experimental conditions. First, since zirconium undergoes a transformation from the a close-packed hexagonal form to the ß body-centered cubic form at 862°C, no recrystallization or grain-growth studies were made above 800°C. Second, because dissolved gases (oxygen, nitrogen and/or hydrogen) increase the hardness and lower the ductility of the solid metal, all annealing treatments in this investigation were carried out in vacuum or in a helium atmosphere. Materials and Methods The zirconium used in this investigation was prepared by the Foote Mineral Co. by deposition from its iodide. A spectrochemical analysis of the metal showed the following composition in weight pct: Hf, 2.1; Mg, 0.012; Fe, 0.035; Si, 0.095; Ti, 0.023; Al, 0.037; Mo, trace; Ni, trace; Cr, trace; Ca, 0.006. Conventional metallographic procedures involving hand polishing on wet metallographic papers, followed by final polishing on fine, levigated alumina on gamal cloth and a medium speed wheel were used throughout this investigation. Grain boundaries were revealed with modified Tucker's etch containing 20 parts glycerine, 2 parts hydrofluoric acid, and one part nitric acid. Grain-Growth Procedure: Three lots of zirconium, designated here as series A, B, and C were prepared for the grain-growth studies as follows: Series A was prepared by cold swaging the % in. as-deposited rod to a 3/16 in. final diameter, followed

Jan 1, 1952

By Irving Lipkowitz

While the light metals are recognized generally as a distinct group in technical literature, economic classifications and data usually still treat them as part of the nonferrous group of metals. However, the economic characteristics of the light metals also differ markedly from those of other nonferrous metals. The distinctiveness of the light metals, as, a group and individually, becomes evident when their growth, since World War II is compared with that of other metals, as in Table 14.3.1. The growth of light-metals production has been much sharper than that of other metals. A weighted average for the light metals shows an increase of 112% during the 1958 to 1968 period. This compares with a 62% increase in the "All Primary Metals" component of the Federal Reserve Board Index of Industrial Production. The contrast was even sharper during the next six years (1968-1974), with light metals production up another 50% as against a 21 % increase in the FRB Primary Metals production index. The most important reason, however, for considering light metals separately is the trend and pace of technological change and not their distinctive statistics. Technology both creates and demands increasingly sophisticated materials. As technology advances and as all the world makes more extensive use of advanced technology, the importance of the light metals is likely to accelerate rapidly. There may be a profound clue to the future in the fact that light metals were predominant among the materials used in the construction of the Apollo 11 spacecraft. In determining what materials to use for the spacecraft and its equipment, the National Aeronautics and Space Administration (NASA) has explained that it did not look to "some of the more exotic metals" and relied instead on "generally proven materials." Accordingly, it apparently used a wide variety of metals, including precious metals, rare earths, special steels, copper, and light metals. What seems particularly significant is that, in seeking performance, NASA relied as heavily as it did on the light metals. Materials breakdown estimates show that aluminum accounted for over 75% of the materials used, titanium for another 5%, and magnesium was also used. Thus, light metals accounted for over 80%' of the materials used for the Apollo 11 spacecraft. The light metals are also unique in their availability. They rank high in abundance among the elements in the earth's crust. Aluminum is the third most abundant element, after oxygen and silicon, with magnesium ranking eighth, and titanium ninth. Among the structural metals, aluminum is the most abundant in the earth's crust, iron is second, magnesium third, and titanium fourth. This potential availability of light metals provides strong incentives for continuing improvements in process technology, because of two major national problems: (1) there is

Jan 1, 1976

By G. R. Countryman, G. H. Thomas, I. Fatt

Miscible displacement in both thewetting and non-wetting phase has been studied in two-phase systems. Experimental data show that dispersion is a function of saturation and cannot be predicted from dispersion theory developed for single-phase miscible displacement. Some of the effect of saturation on dispersion is a result of the development of dead-end pores or a dendritic pore structure in multiphase systems. The presence of dead-end pores or dendritic structure is confirmed by pressure transient studies. INTRODUCTION Displacement by flooding with a miscible liquid is a possible means for recovering the estimated two-thirds of the oil that remains behind after primary production. The immense economic importance of a process that can recover such large quantities of oil has led to extensive laboratory studies of miscible displacement. As usual in production research, most laboratory studies of miscible displacement have not attemped to reproduce all of the conditions existing in a petroleum reservoir. In the early stages of investigation the need has been for information on the broad, basic principles of the phenomena involved in miscible displacement. The effects of overburden pressure, reservoir temperature, and wettability have been considered of secondary importance. However, one property of a petroleum reservoir which is expected to be of major importance and yet has been omitted from many laboratory studies is the presence of interstitial water. Two possible effects of interstitial water on the displacement mechanism in the hydrocarbon phase immediately come to mind. First, from the general1y accepted theory that capillarity governs the distribution of oil and water in porous rock one would expect that for water-wet rock the water will be in the small pores and oil in the large pores. A miscible displacement of oil carried out in the presence of water is operating in a pore size distribution shown in Fig. lb, whereas if the same test had been performed with only one phase present the pore size distribution is as shown in Fig. la. Although there is not yet a theory of miscible displacement which explains in detail the effect of pore size distribution, one would expect the differences between Figs. la and lb to influence the displacement efficiency. A second factor which may make a multiphase system different from a single-phase system is the presence in the multiphase system of dead-end pores or dendritic structure. Experiments of various kinds on reservoir rock have led to the belief that all pores in the network structure of a porous rock take part in conducting fluid during single phase fluid flow.1,2 There are then no dead-end pores and no fingers or dendritic structures containing stagnant fluid. In a multiphase system, however, the second phase may

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By William A. Johnson

THE mathematical analysis of diffusion curves in solid metals is Carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. EXPERIMENTAL PROCEDURE If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942