Search Documents

By Harry L. Washburn

Use of coal thermal dryers has steadily increased since 1928 when one of the predecessor companies of the present Consolidation Coal Cu. constructed a complete preparation plant with thermal dryers. Today there are about 25 additional preparation plants that, all together, use over 65 individual thermal dryers of almost every type. The thermal dryer is a heat generator and the unit may have a separate furnace or a firebox that is an integral part of the dryer. It is also a materials handling device that allows an intimate mixture of wet coal and hot gases with instrumentation for temperature control and. in some cases, the more difficult flow rate of hot gases. The materials handling portion of the dryer is subject to the normal wear and teal of any similar device plus effects of heat, water vapor, moisture: and, sometimes, acid. With present emphasis on air pollution. most fine coal dryers have wet scrubbers.

Jan 8, 1963

By E. Maltby Shipp

WALLACE MCKEEHAN, Douglas, Ariz. (communication to the Secretary*).-In going over this report, which I have done very carefully, I find that the summary as composed deals with the various problems almost entirely from the employer's standpoint and that practically no consideration is given to the employee's point of view. An experience of 3 ½ years as safety inspector, and almost 30 years as workman-and official, has convinced me that any plan for the betterment of working conditions which will achieve any degree of success must give the workmen their share of responsibility and allow them full participation. The company may finance and direct the movement, but its ultimate success depends upon the support given by the workmen. The cooperation of the men doing the actual work is so essential that all writers insist that this must he secured, but they do not agree as to how this can best be done.

Jan 3, 1917

By Robert Longyear

IN, diamond-drill work, a true sample consists of all the material cut by the bit-both core and cuttings. As the recovery of this sample is the object of diamond drilling, the utmost care should be taken to secure it. Speed of drilling and low costs are of little value if an inaccurate sample is obtained. The engineer in charge must study his material and lay out the plan of sampling, and then see that the drill runner follows his instructions; for the runner may be more interested in obtaining a large footage than in developing accurate methods of sampling. FIG. 1.-CORE BOX. When the core has been removed from the core barrel, it should be placed in a core box in the exact order in which it is taken from the ground. This box, Fig. 1, is usually a shallow tray 4 or 5 ft. (1.2 or 1.5 m.) long, with partitions running lengthwise between which the core

Jan 12, 1921

EUGENE WESLEY SHAW,* Washington, D. C. (written discussion ?).-Studies of the probable future production of oil wells and fields-particularly those in the nature of the recent work by Lewis and Beal, having the object of increasing the percentage of recovery-rank, in both practical and theoretic value, very high, if indeed they do not outrank all other petroleum investigations except structural surveys. Even such surveys, although saving untold millions that might have been spent in prospecting unpromising territory, may have less ultimate value than generally supposed, for it may perhaps be argued that much if not most of the condemned territory will sooner or later be tested-some is already productive-and the most that can be rightly claimed is the recovery of cream first; also that the consumption of the richest portions first cannot be extenuated, as it might with some resources, on the ground that if the best is not taken now it will deteriorate.

Jan 5, 1918

By George L. Porter

Mr. President and Gentlemen of the Institute of Mining Engineers: . Unofficially representing the people of the vicinage, it is my pleasant duty to welcome you to the city of Bridgeport, to the valley of the Naugatuck, to the State of Connecticut. The importance and wide-reaching influences of the investigations for which your Institute is organized, the beneficial results which have directly and indirectly blessed mankind from your and kindred studies, the distinguished position which has been achieved in the scientific world by the Institute as a society, and the personal reputation which is the proper recognition of the ability and knowledge of its individual members, assure all that in attempting to honor you we are ourselves honored. In the republic of knowledge no fictitious rewards dignify the incompetent and the ignorant—the attested success of inventions and discoveries in the workshop of nature differentiates her real citizenship. Your present place of meeting is wisely selected ; for this senti-

Jan 1, 1895

By Edmund E. Getzin

Of all the developments in the post-war history of Western Europe, none has been more remarkable in its aims and in the progress it has achieved than the movement toward European integration. It is not an exaggeration to say that this movement marks a virtual revolution, an about-face, in the long and complicated history of European states over the past three centuries. Although sporadic efforts to achieve European integration can be traced back for at least a 100 years, it remained for the breakdown of the European economies as a result of World War II and the subsequent Russian threat to give new impetus to the concept of broader economic and political integration. In fact, the economic integration of Europe following the end of the war was considered so essential that, in 1949, the administrator of the European Cooperation Administration, Paul Hoffman, spoke of the economic integration of Western Europe as an objective of American policy embodied in the Marshall Plan.

Jan 6, 1963

By John Cogan, P. M. Gomez

A typical problem in applied rock mechanics is an accurate prediction of support requirements for deep rock cuts. This paper presents experience with this problem as obtained from excavations for a powerhouse at the Pine Flat Dam near Fresno, California. The project, sponsored by the Kings River Conservation District is still under construction. Highly jointed and weathered rock was discovered during initial excavation. Wedge failures along clay filled joints and bedding planes presented potential support problems. Detailed mapping of joints and beds was undertaken to establish basic patterns of all rock discontinuities including mean orientations and an estimate of orientation variations. Rock bolting patterns were devised to meet these patterns as excavation proceeded. Shear friction angles across joints and beds were estimated from rock wedge fallouts. Friction angles as low as 27º were identified on highly weathered joints. Weathering strongly influenced stability conditions. Examples of bolting patterns to stabilize critical slopes are presented.

Jan 1, 1982

By H. M. St. John

LIKE every present-day manufacturer, the brass foundryman is faced with the necessity of reducing the cost of his finished product without impairing its appearance or quality. He must use every economy that the progress of art and science puts at his disposal and should also be alert to profit by any peculiarity in his own situation or the nature of his product that may give him an exceptional advantage. Much can be accomplished by the adoption of labor-saving equipment and improved methods of melting, molding and handling. Control of pouring temperature, study of defective castings and their causes, laboratory control of molding sand and core mixtures, the use of less expensive alloys, all contribute to the desired end. Assuming that the composition of the alloy is already as inexpensive as the character of the casting will permit, still further savings can be made by the intelligent purchase and utilization of the metals needed to produce the desired analysis.

Jan 1, 1929

By N. H. Parker, J. G. Papailias, G. Gutzeit

In its many forms, the turbine has greater latitude of application than any other mixing device. It is readily adaptable to all tank shapes, from the shallow pan to the tall and narrow stovepipe. Although turbine mixers can be adapted to most tank conformations, experience has shown that there is a preferred shape for optimum efficiency in each service. In the accompanying drawings this relationship is illustrated by the shallower tank for slurry suspension. The taller tank is preferable for continuous staged systems, or maximum retention of the gas phase in absorption. No single turbine covers the entire range of these applications with maximum efficiency. The back-sloped blade offers maximum power economy. The straight blade develops a higher discharge velocity for the dispersion type of service requiring localized shear. The same high shear environment is provided by the back-sloped impeller with stator ring assembly, which permits the most positive discharge control, Fig. 1. Positive stream control is critical in solids suspensions.

Mar 1, 1956

By Harvey P. Knudsen, Young C. Kim, Edward Mueller

Abstract-This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima mine, located near Tucson, Ariz. Results at the Pima mine indicate that the geostatistical method is no better or worse in predicting block grades and total tonnage than the ELIP or IDS methods. In contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELIP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties the geostatistical model is more attractive due to its ability to construct confidence limits on the estimates.

Jan 1, 1978

By L. E. Paulson

INTRODUCTION The Northern Great Plains has 16 billion tons of strippable lignite (1). Presently, 15 million tons per year are mined; essentially all is used for generation of electrical power. In the future, additional large quantities will be consumed in the production of gaseous and liquid fuels. A major consideration in design and operability of power stations and conversion plants is the nature of the ash or inorganic constituents of the lignite used. These inorganic components cause fireside fouling in boilers, exert a catalytic effect in liquefaction and gasification, and contribute to particulate and SO2 emissions. Ash fouling on fireside boiler tubes cause reduced heat transfer and gas flow which limits boiler performance. Severe fouling can result in shutdown of the boiler. A comprehensive test program in both pilot plant and field studies at the Grand Forks Energy Technology Center (GFETC) has shown that ash fouling increases with increased sodium content of low-rank coals (2). The sodium in the coal can be

Jan 1, 1983

By J. R. Campbell

During the past few years, the writer has had occasion to take several excursions into the realms of the washability of beds 3 and 4 of the Pocahontas coal and the proper handling of these coals in prepared sizes Fig. 1.—Washability curve for 4 by 2½-in. egg, PocahoKtas coal. Note that definite break occurs at about 1.60 sp. gr., and washing at this gravity removes all heavy rock and slate, amounting to about 5 per cent. Curve 2 indicates a bony coal, and washed egg coal might not have a good appcarance, and would be condemned by visual inspection, although it would be well prepared mechanically. to attain the greatest realization for the operator and yet produce a market product acceptable to the consumer. Preparation is not new in the southern field, but some new angles have presented themselves in recent years on account of the progress of mechanical preparation. Mechanical methods are entirely devoid of the five senses given to

Jan 1, 1931

By Alfredo O. Del Campo

Copper concentrate smelting has been the subject of significant improvements during the last three decades. Several new processes are being successfully applied at industrial scale, and probably no new copper smelter will be built with the old-fashioned reverberatory furnace. However, because of financial reasons, the existing reverberatory furnaces, which smelt a significant part of the copper produced worldwide, are likely to last at least another decade. Some improvements have been introduced in reverberatory smelting practice, the best known being the use of oxyfuel burners. However, efforts to optimize the reverberatory furnace operation through automatic control have not been reported. The complex and semi-continuous nature of the process makes it dificult to find a suitable strategy for its automatic control. Many factors, like fuel economy, productivity, boiler capacity, refractory wear, converter slag return, copper losses in discard slag, etc. are interconnected. The chosen control strategy should take into account all these factors to achieve good economic results. A detailed discussion of these problems is presented.

Jan 1, 1984

Establishment of a Bureau of Mineral Research at the Michigan College of Mining and Technology, initiated by the State of Michigan with legislation in 1951, is moving toward realization. The Michigan Legislature appropriated $24,000 to cover preliminary costs of plans and specifications for "engaging in a broad, widespread study of the beneficiation of lowgrade ores, of ore dressing, and all the problems of metallurgy that enter into such a program." Ralph C. Calder, of Detroit, who designed Michigan Tech's campus buildings, is preparing plans for the proposed Ores Research Building. Members of the college staff, Professors F. J. Tolonen, W. E. Keck, and Research Engineer Paul Jasberg are assisting in preliminary planning. C. Harry Benedict, retired chief metallurgist of Calumet and Hecla and a member of Michigan Tech's Board of Control, is assisting with technical details. Professor Nicholas Manderfield, head of the department of Mineral Dressing, was assigned to visit other research installations and suggest plans for the Bureau.

Jan 1, 1952

By S. G. Lasky

EVENTS during and since the war indicate that the nations of the world are trying to initiate an era of international co-operation. Definitions and objectives include social, economic, and human considerations no less than political considerations. The mineral resources of the world and the absolute and relative position of each nation enter into this situation. The possible use of armed might, the application of sanctions, the international flow of commerce, the ways in which this flow may encourage or hamper international well-being, and the influence of international and domestic well-being upon one another are all matters that must take mineral resources into account. If the United States is to act wisely and forthrightly in such matters we must be thoroughly informed as to our position with respect to mineral resources. What is the mineral position of the United States? A variety of widely conflicting opinions are held in authoritative and intelligent quarters: (1) For practical purposes our mineral resources are already exhausted.

Jan 1, 1946

By G. B. SOUTHWARD

MECHANIZATION is being developed to some extent in every coal field in the United States and it is rather difficult to say which State or section of the country has made the greatest advancement. Statistics now being compiled for 1928 will show the tonnage mined, the amount of equipment used in each of the coal-producing States, and the comparative tonnages and percentages of total tonnage mined in each of these States, and will reveal which field is making the greatest advancement as far as quantity of production is concerned. However, while the tonnage figures are of great importance there-are other phases of coal-mine mechanization, such as the types of equipment, the mining methods and coal bed conditions, which are of equal interest. The change from hand-mining practices in all of the various operations from the face to the railroad cars is, perhaps, more indicative than any other one thing of the real progress being made.

Jan 1, 1929

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and file this Certificate for that purpose, and do Certify as follows I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained.

Jan 1, 1923

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information thus obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of addresses, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1934

By J. P. Zannaras

If we assume that testing of the model started at time C, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. 1), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t, after time t, motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made.

Dec 1, 1956

By Peter Stubbs

Mr. Agelopas is to be congratulated on a fine paper. Although the presentation was simple and concise, you will all appreciate that a great deal of hard work went into the development of this highly successful repair method. Earlier this year Bethlehem invited a group of our people to witness lug repairs at their Sparrow's Point plant. We have since made lug replacements on a trial basis using their method. The repaired moulds are now back in service. We will compare their performance with regular moulds and with moulds repaired by a technique developed by Dofasco weld shop personnel. I would like to explain briefly some of the various types of ingot mould repairs presently undertaken at Dofasco. The first problem will be familiar to most of you. The lower inside edge of a mould wall may be damaged by spalling, a runout or by the washing action of steel deflected from a badly worn stool cavity. We repair this type of damage by welding.

Jan 1, 1972