Search Documents

By D. F. Kaufman, V. V. Damiano, G. J. London, L. R. Aronin

Beryllium bicrystals were Prepared by a seeding and floating zone-melting technique from high-purity beryllium single-crystal material. The starting material was given six floating zone purification passes prior to producing the bicrystals. Symmetric, asymmetric, and antisymmetric bicrystals were tested in tension. Included were bicrystals with boundaries both parallel and perpendicular to the tension axis. Modified symmetric bicrystals were also examined in detail. In these cases, the angles made by the slip planes with the boundary were not equal. Failure by (0001) cleavage, (1180) cleavage, and boundary separation were all observed depending on the orientation of these cleavage planes and the boundary with respect to the tension axis. Failure occurred on whichever system experienced the greatest normal stress. The origin of the fractures observed and the operative dislocation mechanisms were investigated by frac-tography and transmission electron microscopy. The results indicate that low-angle boundaries form in close proximity to the bicrystal boundary and act as sites for crack nucleation. It has been concluded that, although macroscopic compatibility was satisfied in many of the bicrystals examined, the bicrysta1 boundary was effective in Producing "early" failure by local bend plane formation as plastic deformation proceeded, followed by cleavage initiation and crack propagation. SINGLE crystals of high-purity beryllium oriented with the basal plane inclined 45 deg to the tension axis exhibit a critical resolved shear stress of about 300 psi and 200 pct extension by slipping only on the basal plane before failure by cleavage on that plane. Single crystals, oriented with the basal plane parallel to the tension axis, deform by prism slip at a critical resolved shear stress of 9000 psi and exhibit an extension of over 100 pct before failure in a ductile manner.' In contrast to the behavior of single crystals, poly-crystalline beryllium deformed in tension or bending exhibits little or no ductility at room temperature. Beryllium's lack of ductility at room temperature has been attributed to its lack of a sufficient number of independent slip systems. Beryllium has only four independent slip modes at room temperature and according to the Taylor2 and von Mises3 criteria at least five independent shear modes are necessary to completely satisfy the strain compatibility conditions at all the boundaries in a random polycrystalline sample. Studies of beryllium bicrystals thus appear to provide a convenient way in which to determine whether the condition of strain compatibility is a necessary and sufficient condition to prevent failure and whether obviously incompatible boundary conditions result in boundary separation. Bicrystal studies, although not providing all of the constraints encountered in polycrystalline samples, do allow one to select very specific orientation relation-

Jan 1, 1969

By E. P. Abrahamson II

The effect of transitiorz element bitzary solid solution additions upon the recrystallization temperature of columbium has been investigated. The elements Mn, Fe, Co, Ni, W, Re, and 0s OWY the yecystallization tempel-aturye, while Ti, V, CY, zr, Mo, Ru, Rh, Pd, Hf, Ta, W, Ir, and Pt mise it. A correlation is kloted between the rate of chatzge of recyystallization tewaperature with atomic hercent solute and the free atom electron configuration of the solute element. The work of Abrahamson and Grant1 has indicated a correlation between the free atom ground-state electron configuration and the change in brittle-ductile transition temperature per atomic percent solute in chromium base alloys. A similar correlation was observed for the change in the recrystallization temperature of iron base alloys by Abrahamson and Blakeney and Abrahamson. It was also observed that the limit of rapid change in recrystallization temperature also Correlated with the electronic configuration of the free solute atom. A further study by Abrahamson4 established the generality of the phenomenon by yielding similar results for vanadium base dilute alloys. It has been inferred that a peri- odicity might be expected with changes in the free atom electron configuration of the solvent element. This study is the third set of transition base metal systems to be studied. It is the object of this and further studies on transitional metal systems to detect any systematic variations in the observed correlation which might contribute to the understanding of the electron interactions which are evidently exhibiting themselves. PROCEDURE All alloys were made using 99.9 pct Cb with 0.030 Ta, 0.016 0, 0.0025 H, 0.003 Mo, 0.021 Fe, 0.005 C, and 0.002 N. The solute elements were 99.9 pct pure. According to the published binary phase diagrams5 and metallographic examinations at X750, all additions were in solid solution. The alloys were arc melted and remelted 6 times in the form of cubic 400-g buttons under an argon atmosphere. They were then hot forged at 1200oC to 0.6-in. diameter, annealed for 3 hr at 1200o under argon, and furnace cooled. The specimens were then machined to 0.400 -in. diameter. Grain size was checked and found to remain essentially constant at 150 i 30 grains per sq mm. The specimens were then cold swaged to 0.187-in. diameter, yielding 46 i 1 pct cold work. All alloys were chemically analyzed for the major solute. Analyses of random samples indicated that the impurity content remained at the values of the starting material. Tungsten contamination was held to 0.007 pet.

Jan 1, 1962

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future, by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the cog! washer at Clairton made ii possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coai, Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving I6,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used pn all the remaining ovens. The customary arrangement is 7

Jan 1, 1944

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future, by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the cog! washer at Clairton made ii possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coai, Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving I6,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used pn all the remaining ovens. The customary arrangement is 7

Jan 1, 1944

By Walter Miller

Although confident of its ability to meet any demands that may be made, the petroleum-refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full cooperative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor in full harmony with the nation's needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned. Refining, by constant study and development, by willingness to experiment and install new processes, and to replace older plants with more efficient equipment, had kept on a high plane of efficiency and progress. Working under the free competitive system, it built up its establishments until, as expressed in last year's report, it was easily able to supply any domestic demand that might be placed on it. Turning the United States into the arsenal not only of itself but of the united nations resisting aggression, however, in- creased the call for practically all petroleum products and in particular 100-octane aviation gasoline and high-viscosity aviation lubricating oils. Refining Capacity With over four million barrels a day of crude oil being charged to stills at the year's end, oil refining had broken all records and faced the necessity of further increasing its size to supply the ever-increasing demand for products, some of which, like 100-octane aviation gasoline, were research laboratory curiosities a few years ago. Although the refining capacity of the United States is listed at 4,860,000 bbl., about 800,000 bbl. of this is economically unavailable because of plant location or type. To meet the increasing needs, additional capacity of another half million barrels may have to be built in suitable locations and designed with an eye toward maximum production of aviation gasoline but with inherent flexibility to make it possible to vary and interchange with production of motor gasoline, furnace oils, and other products as necessity dictates. An interesting side light on this refining capacity question was an enquiry from official Washington for knowledge as to any idle refineries of something of the order of 10,000-bbl. daily crude capacity that might be purchased for bodily removal to Russia. 100-Octane Aviation Gasoline Largest of the tasks confronting refiners at the year's end was that of raising

Jan 1, 1942

By Walter Miller

Although confident of its ability to meet any demands that may be made, the petroleum-refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full cooperative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor in full harmony with the nation's needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned. Refining, by constant study and development, by willingness to experiment and install new processes, and to replace older plants with more efficient equipment, had kept on a high plane of efficiency and progress. Working under the free competitive system, it built up its establishments until, as expressed in last year's report, it was easily able to supply any domestic demand that might be placed on it. Turning the United States into the arsenal not only of itself but of the united nations resisting aggression, however, in- creased the call for practically all petroleum products and in particular 100-octane aviation gasoline and high-viscosity aviation lubricating oils. Refining Capacity With over four million barrels a day of crude oil being charged to stills at the year's end, oil refining had broken all records and faced the necessity of further increasing its size to supply the ever-increasing demand for products, some of which, like 100-octane aviation gasoline, were research laboratory curiosities a few years ago. Although the refining capacity of the United States is listed at 4,860,000 bbl., about 800,000 bbl. of this is economically unavailable because of plant location or type. To meet the increasing needs, additional capacity of another half million barrels may have to be built in suitable locations and designed with an eye toward maximum production of aviation gasoline but with inherent flexibility to make it possible to vary and interchange with production of motor gasoline, furnace oils, and other products as necessity dictates. An interesting side light on this refining capacity question was an enquiry from official Washington for knowledge as to any idle refineries of something of the order of 10,000-bbl. daily crude capacity that might be purchased for bodily removal to Russia. 100-Octane Aviation Gasoline Largest of the tasks confronting refiners at the year's end was that of raising

Jan 1, 1942

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By H. G. Dwyer

CONSIDERATION for future expansion influenced the design of the new smelter at Chuquicamata. The section of the smelter now going into operation, while large, represents only little more than half of the ultimate plant. Equipment for the direct smelting of raw concentrates has been arranged in the conventional manner although needless details have been eliminated wherever possible while mechanical and electrical features not usually found in copper smelters have been incorporated. Access is afforded to all equipment but platforms and walkways have been held to a minimum. The poling and other platforms in the converter aisle, normally subjected to battering by ladles and other heavy equipment in transit, are of concrete construction with steel grid armor embedded in the exposed surfaces. Noticeably absent are the many platforms formerly required for the handling of converter flux since this material is charged to the converters through the side walls of the converter uptake hoods. Clear space with ample headroom is provided under each converter and converter puncher's platform to permit clean-up by small bulldozers. Remote controls have been introduced at many points. Electrical control rooms and control centers have been conveniently located. An electrical tunnel with cross tunnels and escapeways is situated under the entire length of the converter aisle for power feed lines. Skull breaking facilities are in a separate building near the smelter. A silica-slurry building with brick storage area is adjacent to the smelter building so that elevator service is available to both buildings. A smelter office, a change house and lunchroom are provided in convenient locations. Units of the smelter as presently constructed are shown in the plan and table on page 1194. The ultimate smelter will house 7 reverberatory furnaces, 14 waste-heat boilers, 9 Peirce Smith converters, 4 casting furnaces serving 2 casting wheels, and one holding furnace serving a straightline casting machine. Additional crane requirements in the converter aisle will necessitate the installation of special hoisting equipment in space already provided in a raised section of the roof over the casting end of the aisle. Thus a complete crane may be lifted high enough above the crane rails to permit the passing of another crane underneath thereby giving all cranes full use of repair facilities already installed. For the collection of gases, 2 dust chambers, each with separate stacks, will collect converter gases and 2 balloon flues with separate stacks will collect reverberatory furnace gases. Extensions necessary to complete the ultimate plant will be possible with little interruption to normal operations since the future converters and reverberatory furnaces will be added at the east end while additional casting facilities will be added at the west end of the present plant. The future units may be added singly or all at one time depending on requirements.

Jan 1, 1952

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By Walter Miller

BY the beginning of 1945 the output of petroleum products for war had reached a volume and a rate of growth which practically assured all requirements so long as war continued. The programs for making gasoline, lubricating oils of required quality, toluene for T.N.T., and chemicals for manufacture of synthetic rubber, as well as numerous other lesser petroleum products, were all well in hand, and unless catastrophic developments occurred there was no doubt of the ability of the industry to meet all demands. The end of the fighting found the refining industry working at top capacity on war commodities, but also in position to convert quickly into peacetime civilian production. 100-octane Aviation Gasoline Production of the vital 100-octane aviation gasoline, starting with approximately 44,000- bbl. daily capacity at our entry into the war, reached a top of 525,000 bbl. a day in the United States by the end of hostilities. With 75,- bbl. from other Allied sources, the grand total was 600,000 bbl., or 25,000,000 gal. each 24 hr. available to the armed forces had fighting continued. At times it was a close race between requirements and production, but never were any important military operations involving the use of high-octane aviation gasoline held up or delayed for lack of sufficient output of such material. The undivided effort of the entire refining industry in full cooperation with the Government made this record possible. Little diminution in output followed the German surrender on May 7. Plans called for a correspondingly greater activity for the Japanese war and possibly for well into 1946. But when the Japanese sued for peace on Aug. 10 most contracts were quickly canceled. Substantial stocks, reputed to be somewhere between 20,000,000 to 30,000,000 bbl., built up largely between V-E and V-J day pending organization of the larger Japanese war program envisaged after Germany gave up, were in the Government's hands in this country, in addition to working stocks in the war areas. Toluene and Lubricating Oil Requirements for toluene for T.N.T. increased rapidly as bombing speeded UP with increasing control of the air by the Allies in Europe and Asia. Production in excess of T.N.T. requirements which had been going into 1000-Octane aviation fuel blending during 1943 and 1944 was again drawn into explosive manufacture early in 1945. In anticipation of the war continuing into 1946, two new plants were ordered constructed, the decision being announced in April, plans calling for one of them to get into production about the end of 1945, the other in the first quarter of 1946. Both of these projects were later canceled as victory made it evident that the additional supplies would not be needed. Production was

Jan 1, 1946

By Walter Miller

BY the beginning of 1945 the output of petroleum products for war had reached a volume and a rate of growth which practically assured all requirements so long as war continued. The programs for making gasoline, lubricating oils of required quality, toluene for T.N.T., and chemicals for manufacture of synthetic rubber, as well as numerous other lesser petroleum products, were all well in hand, and unless catastrophic developments occurred there was no doubt of the ability of the industry to meet all demands. The end of the fighting found the refining industry working at top capacity on war commodities, but also in position to convert quickly into peacetime civilian production. 100-octane Aviation Gasoline Production of the vital 100-octane aviation gasoline, starting with approximately 44,000- bbl. daily capacity at our entry into the war, reached a top of 525,000 bbl. a day in the United States by the end of hostilities. With 75,- bbl. from other Allied sources, the grand total was 600,000 bbl., or 25,000,000 gal. each 24 hr. available to the armed forces had fighting continued. At times it was a close race between requirements and production, but never were any important military operations involving the use of high-octane aviation gasoline held up or delayed for lack of sufficient output of such material. The undivided effort of the entire refining industry in full cooperation with the Government made this record possible. Little diminution in output followed the German surrender on May 7. Plans called for a correspondingly greater activity for the Japanese war and possibly for well into 1946. But when the Japanese sued for peace on Aug. 10 most contracts were quickly canceled. Substantial stocks, reputed to be somewhere between 20,000,000 to 30,000,000 bbl., built up largely between V-E and V-J day pending organization of the larger Japanese war program envisaged after Germany gave up, were in the Government's hands in this country, in addition to working stocks in the war areas. Toluene and Lubricating Oil Requirements for toluene for T.N.T. increased rapidly as bombing speeded UP with increasing control of the air by the Allies in Europe and Asia. Production in excess of T.N.T. requirements which had been going into 1000-Octane aviation fuel blending during 1943 and 1944 was again drawn into explosive manufacture early in 1945. In anticipation of the war continuing into 1946, two new plants were ordered constructed, the decision being announced in April, plans calling for one of them to get into production about the end of 1945, the other in the first quarter of 1946. Both of these projects were later canceled as victory made it evident that the additional supplies would not be needed. Production was

Jan 1, 1946

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By R. R. Hoffman

The name L'brush,l as applied to the parts to be briefly considered in this paper, is not clearly descriptive of the design and function of those parts when the usual definition of the word is applied. In a general way, the brushes to be considered here are the parts employed on certain types of electrical equipment to facilitate the transfer of electrical current between a rotating or moving element and a stationary element. These machines are generally motors and generators of both the slip-ring and commutator types, rotary converters, battery charges, etc. Parts that serve a similar purpose on relatively slow or intermittently moving devices such as rheostats, switches, controllers, etc., are generally referred to as contacts. A few special applications involve the use of current-carrying washers, rollers, bushings, etc. As may be inferred, therefore, the design of these brushes and allied parts is dictated by both electrical and mechanical considerations. In most cases these factors are closely interrelated, and unfortunately many of them are not subject to exact scientific or mathematical analysis. Special Advantages Since brushes operating on direct-current machines must carry the load current, resist destructive action from voltage induced in imperfectly compensated armature coils, and in addition act as a bearing material, maintaining intimate contact with the commutator at peripheral speed, which may be as high as 70 miles per hour it is difficult to obtain in one brush the ideal properties necessary for perfect functioning under all operating conditions. The engineer-designer, therefore, when selecting a brush for a specific application, must choose a grade that possesses the characteristics most adequate to meet the conditions involved. In many cases a characteristic that makes a specific grade of brush the ideal selection for one type of machine may be of secondary importance to some other property when the brush is applied on another machine. Frequently different grades of brushes must be applied to the same type of machines when they operate under different or unusual atmospheric conditions. Completely satisfactory brush operation depends on freedom from appreciable sparking, minimum electrical and mechanical losses, negligible commutator or slip-ring wear, uniform film over the commutator or slip ring, quiet operation and good brush life. The ability to produce special structures, and to combine in widely varying proportions materials that are incompatible, through conventional melting and alloying procedures has been the basic contribution of powder metallurgy to the solution of problems involving brushes and allied parts. This is especially true where current-carrying capacity is a major factor, owing to the limitations of all carbon or all graphite brushes in that respect. Metal-graphite Brushes With very few exceptions, friction between moving elements. across which

Jan 1, 1945

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By T. I Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The Darrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook1 and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outline and comes to within about 4625 ft. of the surface. At this depth the diameter of the salt plug is approximately 4800 ft. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The line showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable. Surveys with Refraction Seishograph and Torsion Balance A reported oil show in a water well drew attention to the lands of the Belle Helene

Jan 1, 1943

By J. Brian Eby, T. I. Harkins

This paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The Darrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook1 and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outline and comes to within about 4625 ft. of the surface. At this depth the diameter of the salt plug is approximately 4800 ft. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The line showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable. Surveys with Refraction Seishograph and Torsion Balance A reported oil show in a water well drew attention to the lands of the Belle Helene

Jan 1, 1943

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades' of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. CLAIRTON BY-PRODUCT COKE PLANT AND COAL WASHER The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of- approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1943

By W. W. Schmittroth, A. Y. Bethune

The commercial analysis of Special High-Grade zinc usually involves the determination of lead, iron, copper and cadmium as impurities in the base metal. Over the past 20 years, as the result of metallurgical improvements in the art of producing Special High-Grade zinc metal there has taken place a gradual exclusion of almost all extraneous elements, and the few that do remain in the final product have been virtually reduced to the vanishing point. Thousands of tons of zinc are now commercially produced annually and made available to the trade, in which impurities are present only in the order of 0.0010 per cent or less and the sum total of all impurities does not exceed 0.0025 per cent. To such zinc the term "super-purity" might well be applied without undue exaggeration. The techniques used for production control and final analysis of Special High-Grade zinc by means of emission spectra in the laboratories of the electrolytic zinc plant of the Sullivan Mining Co. are based on the premise that self-electrodes are to be preferred over all other forms for the examination of the zinc in question. Furthermore, after a survey of the literature and considerable experimental work,' it was decided that the spectrographic method of internal control, the principle of which was first announced by Gerlach,2 using a modification of the high-voltage alternating-current arc source introduced by Duffendack and Thompson,3 with the calibration of each photographic plate as recommended by Wolfe,4 would yield the most accurate and reproducible results. Self-electrodes were chosen in order to make use of one of the unique advantages inherent in spectrographic analysis; namely, the rapid and almost effortless detection of elements other than those being quantified by the analyst; or conversely, the proof that the zinc is free from such impurities if no spectral line of the suspected element appears. This fact was verified for certain elements, and will be discussed later. Carbon electrodes impregnated or packed with zinc salts chemically prepared from the zinc to be assayed were avoided for a number of reasons. First, the chemical manipulation was another time-consuming step, which increased the chances for contamination. Second, none of the common zinc salts, such as the chloride, nitrate or sulphate, yielded reproducible results under our conditions, nor did the spectral line of the impurity appear as readily in the low concentrations as when using zinc metal. Third, no commercial carbon, except the very expensive, was pure enough to use with this grade of zinc and the continued time, effort and expense incurred in the purification of carbon were not desirable. The use of special High-Grade zinc self-electrodes introduces certain complications with regard to obtaining satisfactory excitation conditions, because it seems necessary to raise the temperature

Jan 1, 1949