Search Documents

By C. Gatlin, N. E. Garner

Results of impulsive wedge penetration tests on two synthetic, plastically deforming rocks are presented. Basic data obtained were force-time, displacement-time, and force-displacement curves for the impacts, plus the crater geometry. Wedge geometry and blow frequency were varied over a considerable range. The synthetic rocks consisted of wax-sand mixtures; two waxes of diflerent ductilities were used to provide variable "rock" characteristics. Conventional triaxial tests showed that these synthetic rocks exhibited force-deformation curves and Mohr envelopes quite similar to real rocks, except that strengths were much lower. Measured forces from static penetration tests agreed closely with theoretical values; however, dynamic force values were much higher than the static. These latter disparities are attributed to the viscous nature of the waxes. Thus the utility of these or similar rock models must depend on the scaling of rock viscosity, which is as yet unknown for impulsive loadings at elevated stress states. It appears, however, that some macroscopic, static phenomena may be studied with wax-sand rock models. INTRODUCTION The resistance of solid materials to indentation or perforation by projectiles or other penetrators has been studied by workers in many areas. Despite these efforts no universally accepted laws or formulas are available for describing experimental observations. In the metals field the force-deformation behavior of impacting bodies is often analyzed by the Hertz law for elastic collisions, the Meyer law if plastic deformations occur, or some combination of both.' The similarities of these expressions to empirical drilling formulas of the oil industry are apparent. Beginning with the basic contributions of Simon and co-workers at Battelle,' a number of experimental papers concerning the reaction of rocks to vertical impact have appeared in the U. S. mining and petroleum literature.'-' Most published data have, to date, been obtained at atmospheric pressure, although some early high pressure information was reported by Payne and Chippendale.8 Maurer" has recently utilized available brittle impact data to develop a drilling rate equation based on the experimentally observed proportionality between crater volume and blow energy. His result agreed with earlier efforts by both Somerton, who used dimensional analysis, and Outmans, who used plasticity theory. It has long been known that rocks exhibit different modes of failure depending on the state of stress. The literature in this area is considerable; however, papers by Bredthauer, Handin and Hager,13 nd Robinson", are adequate to illustrate the point. Since rocks flow plastically at certain triaxial stress conditions, the mathematical theory of plasticity has been used to analyze the rock drilling problem. Cheatham'" has altered the wedge identation solution of Randtl to rocks, and has developed useful equations for penetrator forces under a variety of conditions. Outmans" has utilized Hill's solution in a similar manner to develop a drilling rate equation. Both Cheatham and Outmans used the linear Mohr-Coulomb rule to relate rock strength and confining pressure. The actual stress at the hole bottom is not easily ascertained, although photoelastic studies by Galle and Wil-hoit," plus the analytical treatment of Cheatham and wilhoiti8 provide some insight. Consequently it is not clear to what extent the highly idealized rheological model of a perfectly plastic solid can be realistically applied to the rock drilling problem. This paper is the first report on a long range experimental study of crater formation in rocks at elevated stress states. The data presented here are from the first phase of the project. Data obtained from impulsive wedge impacts on two synthetic, plastically deforming rocks are presented. MODEL ROCKS Geologists have long been faced with modelling the behavior of the earth and, as a consequence, have studied scaling problems in some detail.' In general, their main problem is handling the wide disparity between laboratory and geologic time. In our studies the time effects (blow velocity or rate of loading, blow duration, etc.) were essentiafly the same for both. model and prototype, as were were geometry and tooth penetration. Thus application of available scaling laws suggests that Similarity is obtained if the stress-strain curves of model and prototype are similar." For this reason Hubbert and Willis''

By R. R. Angel

Drilling rate is a parameter that should be considered in determining the volume requirements for air and gas drilling. The use of past methods which ignore the effects of the solids content upon the pressure and velocity of the annulus flow stream can result in undercalculation of the required volurne by as much as 50 per cent. A vertical-flow equation is presented for determining volume requirements. This equation includes the effect of the solids that are transported up the annulus in the flow stream by incorporating the drilling rate as one of the parameters. The effect of down-hole temperature on required circulation rates is also ana-lvzed. A simple approximate method of determining volume requirements is presented. This method is more accurate than the methods used in the past. Hole cleaning difficulties are analyzed for a recent air drilling job where past methods indicated that - excess air was being used. Sample curves of calculated boitom-hole pressures are presented for air and gas drilling in several hole sizes. INTRODUCTION In certain areas the use of air or natural gas as a circulating medium for drilling oil and gas wells is becoming a common practice. Large increases in penetration rate and bit life are achieved through the use of these media in preference to mud or water. Drilling rates as high as 90 ft/hr have been obtained in shales. The importance of maintaining adequate circulation rate is generally recognized; however, much disagreement exists among drilling operators as to what constitutes "adequate" circulation rate. In quarry drilling, where annular velocities can be accurately determined, an annular velocity of 3,000 ft/min of standard air is required for best results in rocks having approximately the same density as those commonly penetrated in drilling oil or gas wells'. Although this standard air velocity has proven satisfactory for quarry drilling, some oil and gas well drilling operators believe that an equivalent annular velocity of more than 4,000 ft/min is required; others believe that as little as 2,000 ft/min . is sufficient. Much of this disagreement results from determining the required circulation rates with methods which fail to incorporate the drilled solids in an equation which is applicable to vertical flow. Hughes Tool Co. Bulletins No. 23' and 23-A3 present data for determining circulation rates based on the Weymouth formula. These data do not include the drilling rate as a parameter and, therefore, neglect the effect of the solids being transported up the annulus. In spite of this apparent defect and the fact that the Weymouth formula is not applicable to vertical flow, the Hughes data have well served the drilling industry in many areas and are important and timely contributions to the science of air and gas drilling. The Hughes data purposely omit a correction for increasing down-hole temperature. At slow drilling rates this effectively compensates for the use of a formula which is not valid for vertical flow; however, volumes determined by the Hughes method are not sufficient to support rapid drilling rates at moderate and great depths. For example, Phillips Petroleum Co.'s Cauthorn "D" No. l in the Vinegarone field for Val Verde County, Tex., was air drilled from 1,500 to 9,300 ft using a compressor delivering 1,400 cu ft/min. The 8 3/4-in hole was drilled with 5-in. drill pipe, and drilling rates as high as 90 ft/hr were obtained between 7,000 and 9,300 ft. No water or caving hole was encountered. At 7,728 ft it was necessary to wash-out 60 ft of cuttings to reach bottom after a trip to change bits. At 8,130 ft a twist-off occurred and the drill col-lars were stuck in drill cuttings. These difficulties indicate that the 1,400 cu ft/min of air was not sufficient to keep the hole clean. Hughes data indicates that 1,180 cu ft/min is sufficient to produce an annular ve-

Jan 1, 1958

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5' is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester' have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5' is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958

By D. R. Hay, E. Scala

STUDIES of structure-sensitive properties, especially mechanical behavior, have shown that grain and subgrain structure play an important role. The mechanical properties of tungsten, in particular, are sensitive to the nature of the intergranular structure. Substructure and dislocation networks in single-crystal and polycrystalline tungsten have been studied by Nakayama et al.' Various orders of substructure were observed ranging from a microscopic first order (grain diameter: 2 to 8 mm) to a microscopic second order (grain diameter: 50 to 300 p), and, within the latter, dislocation networks forming an even smaller order of substructure. In their single crystals, grown by arc fusion, the degree of misorientation in each order was small: 16'3OU, -11, and -10" for the first-, second-, and third-order substructure, respectively. To study the properties of polycrystalline tungsten, powder metallurgy tungsten is generally used. However, in a mechanical property investigation, the zone-melted or arc-fusion crystals are more desirable than the powder metallurgy product due to their higher purity and absence of porosity and other defects inherent in consolidation by powder metallurgy. Grain boundaries can also be produced in melted stock by working and recrystallizing. However, material with subgrain mis orientations of the order of several degrees (high-angle substructure) has not been reported previously and is the subject of this communication. Crystals were grown by electron-beam, floating-zone melting. The starting material, Sylvania Pure-tung welding rod, was given one zone pass at a traversal rate of -2 mm per min. Through control of the zone temperature, it was possible to influence the degree of crystal perfection. By maintaining the zone at a high degree of superheat, high-perfection crystals could be grown. However, at temperatures only slightly above the melting point, the zone-melted crystals contained a high-angle substructure. A sensitive control of the zone temperature was not possible due to the difficulty of estimating the temperature of the zone and of providing a constant supply of power to the sample. Therefore, an empirical method, using the shape of the molten zone as a criterion, was adopted as an indication of temperature. At high degrees of superheat, the surface tension of the molten zone decreases and a neck forms at the top of the zone, whereas at low zone temperatures the diameter of the zone remains reasonably uniform. Although it was not possible to obtain a continuous variation of misfit angle, the conditions could be directed toward the growth of either high- or low-angle substructure by maintaining only a slight neck in the zone (sufficient to establish that it was molten) or a well-necked zone, respectively. Mass spectrographic analyses of both types of material revealed no significant differences in the concentrations of their impurities. The degree of misorientation at high angles was obtained by measuring the angular spread of spots corresponding to a single reflection on a Laue back-reflection photograph. Fig. 1 shows a typical Laue back-reflection photograph of a crystal with a 3-deg spread. By measuring the angular deviation of the spots corresponding to a single reflection from the mean center of the spots around which constant angular deviation contours were drawn, an average angular spread of misfit could be calculated. The angular average was weighted by the number of spots observed in each angular interval. At angles greater than 5 to 6 deg the spots from different reflections begin to overlap, and cannot be associated with a particular reflection. Laue back-reflection photographs taken at different locations on samples .with approximately 3-deg spreads showed only a small difference in angular misorientation, less than 8' of arc, within individual specimens. The microstructure was examined using Berg-Barrett X-ray extinction contrast microscopy. Berg-Barrett photographs taken directly on the as-grown surface, Fig. 2, show an essentially equiaxed subgrain structure of -0.1 mm in average grain diameter in both high- and low-angle crystals. Fig. 2(a) is a photograph of a sample with a low misfit angle and Fig.

Jan 1, 1968

By John E. Willson, Ben L. Seegmiller

A portable electronic instrument was designed and constructed to detect unknown stress magnitudes in rocks. The principle used to detect stress is based on the propagation velocity method. This method allows the stress in a rock subjected to a load of unknown magnitude to be determined, provided that the wave velocity-stress relationship for similar rock is known. This is accomplished by measuring the travel time of longitudinal mechanical waves passing between two points a set distance apart in a rock. The velocity of the wave is calculated and the stress determined from the wave velocity-stress relationship. If the sending and receiving transducer spacing is constant, a time vs. stress relationship rather than the velocity-stress relationship may be used. The method is nondestructive and tests can be made without drilling or otherwise disturbing the rocks. The first studies undertaken in the United States to determine stress in rocks using propagation velocity techniques were reported by Obert1,2 in 1939 and 1940. The Soviet Union first reported using propagation methods to study rock pressures in 1951.8 Success of the method led to the development of a pulse-type ultrasonic seismoscope4 in 1953. Using this instrument, Ivanov and Betaneli5,6 in 1963 succeeded in devising and testing under field conditions a method of investigating coal pillar stresses. In 1967 Osipova7 reported results of similar studies in the Nakhichevan salt mines. In France, Tincelin8 has used the propagation velocity method to study the stress distribution in iron ore pillars. Uhlmann9 has investigated stresses in salt and potash pillars in Germany, using velocity techniques. Determination of uniaxial stress by propagation velocity methods is limited to rocks which have readily detectable wave velocity-stress variations. The present stress detection instrument is restricted in application to rocks which have a velocity change under stress of at least 300 fps. Examples of rocks which meet this requirement are sandstones, coal, and possibly some limestones. Testing of this instrument was limited to a laboratory study and the results may or may not be indicative of what would be found in a field test. A program of field experiments to study the feasibility of using this instrument to determine mine pillar and tunnel stresses is in progress. Instrument Design The instrument has two main components: A probe and a control-display unit. The probe is a hand-held device to which two identical rodlike transducers are rigidly mounted. Coaxial cable connects the probe to the control-display unit which is mounted in an enclosed carrying case measuring 7 % x 9 x 13 in. The instrument is designed so it may be carried and operated by one man. Weight of the probe and enclosed control-display unit is approximately 20.1b. The probe consists of two transducers identical in construction. One transducer is used to convert electronic pulses to mechanical waves and transmit these waves into a rock. The other detects the transmitted waves in the rock and converts them back into electronic signals. The basic element in both transducers is a piezoelectric crystal. The crystal is a disk made of lead titanate zirconate and has a natural resonant frequency of 400 kHz ±1% in the thickness mode. A schematic of one of the two identical transducing elements is shown in [Fig. 1.] A spacing of 6 in. between sending and receiving transducers has been found to be most satisfactory. The control-display unit consists of a pulse generator and a 1-in. oscilloscope. Various electronic devices are used for the power supply, amplification, and calibration. The amplitude of the square wave from the pulse generator can be continuously varied between 0 and +20 vdc. Pulse width can be set at 1, 2, 3, or 4 µsec. The repetition rate of the pulse can have the following values: 50, 75, 100, 150, 200, 250, 300, 400, 500, 750, and 1000 Hz. The oscilloscope delay system allows the travel time of the longitudinal wave passing through a rock to be measured to an accuracy ±0.1 µsec in the range from 0 to 995 µsec. Fig. 2 is a schematic of the various electronic sections in the control-display unit. Laboratory Testing The first step in using the instrument is to develop a velocity-stress or a time-stress curve for the par-

Jan 1, 1972

By Steve H. Carpenter, Henry E. Otto

The explosive welding of metals is dependent upon the production of a jetting action caused by the collapsing of one metal plate against another. Successful welds are generally accomplished if the yield strength of the metals is in the range of 10,000 to 90,000 psi and the sonic velocity of the metal is greater than the detonation velocity of the explosive if direct contact explosive is being used.' Should the detonation velocity exceed the velocity of sound in the metal it may still be possible to obtain the jetting action and a good weld. However, in most cases where a high detonation velocity is used complications arise because of reflected shock waves which tear the bond apart as fast as it is put together.' Explosive welding of lead presents several problems since its yield strength and sound velocity are very low. Various values have been published3-5 for the velocity of sound in lead ranging from 2000~ to 23004 m per sec. Most of the high-order explosives have detonation velocities on the order of 6000 to 8000 m per sec, which precludes their use. The dynamites have a lower detonation velocity of around 2800 m per sec which is still somewhat too high. Lower-order explosives such as ammonium nitrate (1070 m per sec) must be used to weld lead in the as-received condition if the explosives are used in direct contact. Rather than use low-order explo'sives it was decided to alter the sonic velocity of the lead. The sonic velocity is directly related to the modulus of the material according to the following expression: Fig 1—Interface of explosive weld of lead to steel. Lead is on top As-polished Magnification 75 times as well as the yield strength. Bolling et al. 6 show that the shear modulus of lead single crystals increases from about 0.72 X1011 dynes per sq cm at 300°K to about 0.98 X1011 dynes per sq cm at 0°K, an increase of approximately 3 5 pct. This gives an increase in the sonic velocity of around 700 m per sec. Hence, the sonic velocity of lead at cryogenic temperatures is approximately equivalent to the detonation velocity of the low-order dynamites. We have obtained high-quality lead to steel explosive welds using a 40 pct dynamite in direct contact with the lead. Prior to detonation the lead was chilled with liquid nitrogen (78°K) to increase the strength and sonic velocity. Welds were made while the lead was cold. Specimen sizes were 3 by 6 in. A preset angle of 5 deg with a 0.10-in. standoff at the base was the geometrical setup used. The amount of explosive used for optimum welding of an 1/8 -in. -thick lead sheet to a steel plate was found to be 7 g per sq in. A PETN sheet explosive line wave generator was used to insure a linear detonation front through the dynamite. A photomicrograph of a lead-steel weld is shown in Fig. 1. The typical wave effect that constitutes a good explosive weld is present. When tested in shear, the weld failed in the lead, indicating that the bond is stronger than the lead base metal. Higher-order explosives were also tried without success. We believe this indicates the importance of matching the detonation velocity and the sonic velocity for successful explosive welding. Note Added in Proof. High quality explosive welds of lead to steel have recently been obtained at ambient temperature using a low velocity (1000 M per sec) free running dynamite. The weld interface obtained is comparable to Fig. 1. 'S. H. Carpenter, R. H. Wittman, and R. J. Carlson: Proceedings of the First International Conference of the Center for High Energy Forming, Syracuse University Press, syracu.se, N. Y., in press. 'A. HI Holtzman and G. R. Cowan: Welding Risearch. Council Bull., No. 104, April, 1965. 'Metals Handbook, 8 ed., p. 1062, Metals Park, Ohlo. 'J. M. Walsh, M. H. Rice, R. G. McQueen, and F. L. Yarger: Phys. Rev., 1957, vol. 108, pp. 196-216; 'L. V. Al'tshuler, K. K. Krupnikov, B. N. Ledener, V. I. Zuchikhin,

Jan 1, 1968

By Wm. R. Dotson

Forty years ago the atom was split and the Age of Fission dawned. Uranium was the element used in this earth-shaking accomplishment. Thitherto almost unknown to the man in the street, uranium soon became widely and persistently sought. And the quest for this unique material is not likely to diminish during this century. To find is one thing; to own is another. Who owns uranium in the ground? Where no mineral rights in the land have been severed by devise, grant, reservation or lease, the uranium belongs to the fee simple owner of the land. But where there has been a conveyance or reservation of all or part of the "minerals", determining WHAT a substance is has been the traditional way of determining WHO owns it. What, then, is this element called uranium? The 1907 edition of Watts Dictionary of Chemistry calls it "a lustrous, hard, silver-white metal". Of nature's three prime divisions it falls within the embrace of the mineral kingdom - substances neither animal nor vegetable. In its natural state uranium always is combined with other elements or substances in the form of an ore mineral. May we, then, put to rest any doubt or question as to the nature of uranium and classify it for all purposes, including that of ownership, as mineral? Not quite! That self-same logic would find oil and gas primly ensconced in the animal or vegetable kingdom. Technically, oil and gas are not minerals but legally they have been classified as such. Why? The Supreme Court of Tennessee sought the answer in 1897 in the case of Murray v. Allard, 43 S.W. 355. After citing authorities pro and con, and while admitting their origin to be "decomposition of marine or vegetable organises" that court firmly concluded that since they were obtained by a form of mining, oil and gas were minerals. From the above example two elementary truths emerge. First, for purposes of ownership, uranium is and will be whatever the courts say it is. Secondly, the courts historically and currently favor a practical rather than technical test to determine the "mineral" character of a substance. So now we turn to the jurisprudence for enlightenment and definition. EARLY CASES ALLOT URANIUM TO MINERAL OWNERS Two early cases involving the ownership of uranium followed what had been well-settled mineral within the meaning of the conveyances involved, confirming ownership in the mineral owners. In 1956 the U. S. District Court for New Mexico in the case of New Mexico and Arizona Land Company v. Elkins, 137 F. Supp. 767, appeal dism'd 239 F.2d 645 (10th Cir. 1956), found that a 1946 deed reservation of "all oil, gas and minerals underlying or appurtenant to said lands" included uranium and thorium. The court reasoned that uranium and thorium, being minerals within the scientific, geological and practical meaning of the term, would certainly constitute minerals within the purview of the reservation. While agreeing that uranium and thorium were "minerals", defendants argued that at the tine of execution of the conveyance it could not have been the intention of the parties to reserve them because they had no commercial value in the locality and were, in fact, not known to there exist until their later discovery in 1950. The court re¬jected, as a matter of law, this "lack of knowledge" theory citing the Supreme Court of Kentucky holding in Maynard v. McHenry, 113 S.W. 2d 13, that: "The mere fact that a particular mineral has not been discovered in the vicinity of the land conveyed or is unknown at the time the deed is executed rules of construction and held that uranium was a does not alter the rule . . ." that a grant or exception of "mineral" in a deed includes all mineral substances which can be taken from the land unless restrictive language is used indicating that the parties contemplated something less general than all substances legally cognizable as minerals. Further, argued the defendants, the only feasible mining procedure for such substances was open pit or strip mining, which would destroy the value of the land for grazing or agriculture. Finding that the language of the reservation was clear and unambiguous, the court would not permit the admission of extrinsic evidence as to mining procedures required. Elkins is the first uranium case construing the granting clause involved. In 1958 the Texas Court of Civil Appeals at San Antonio, in Cain v. Neuman, 316 S.W. 2d 915, no writ, held that a 1918 lease conveying "all of the oil, gas, coal and other minerals in and under" the land involved covered uranium. The lease provided a royalty of 1/10th on "other minerals." "We find no Texas precedent which discusses uranium," said the court, "but the usual arguments that uranium is not embraced within a lease are that the ejusden generis rule excludes uranium from the meaning of the lease

Jan 1, 1979

By W. N. Lacey, R. H. Olds, B. H. Sage

Samules of liquid and gas were obtained from the primary separator of a well in the Paloma field. The volumetric properties of the samples and of six systematically chosen mixtures of the samples were experimentally determined at 100°, 190°, and 250°F. at pressures up to 5000 lb. per sq. inch. From these data the influence ,of pressure and temperature upon the composition and specific volume of the bubble-point liquid and of the retrograde dew-point gas was established, The formation volumes and gas-oil ratios of the rnixtures investigated were calculated on the basis of the plant-product oil, which is defined as the isobutane and less volatile portion of each mixture. The results are presented in graphical and tabular form. The volumetric behavior of the mixture corresponding to that produced by the well at the time of sampling was determined for 235ºF., the reported reservoir temperature, by graphical interpolation of the experimental data with respect to composition and temperature. The results indicate that the well-production mixture probably existed as a gas at its retrograde dew point under the conditions of temperature and pressure believed to prevail in the producing zone at the time of sampling. The effect upon the phase behavim occasioned by the omission from the well-production mixture of certain components of intermediate molecular weight was investigated. In the first case, all of the isobutane and 11-butane, and substantially all of the iso-pentane, were removed from the mixture of trap samples corresponding to the well production. In the second case, all the propane, isobutane and n-butane, and substantially all of the isopentane, were removed. Both modifications led to considerable increases in the retrograde dew-point Pressure at 235ºF.; an increase of 558 lb. Per sq. in. above that of the unmodified well-production mixture in the first case, and an increase of 1208 lb. Per sq. in. in the second. It was concluded that the material? remaining after the removal of certain components of intermediate molecular weight could not be injected back into the reservoir in the saqe proportion in which they were produced without entailing appreciable loss of liquid material through condensation within the formation. Introduction Under the usual conditions of production practice, petroleum arrives at the surface of the earth in a physical state considerably different from that in which it existed in the underground reservoir. The relative rates of production and the properties of oil and gas measured at surface conditions do not constitute, in general, even a qualitative description of the fluids existing in the reservoir. The estimation of reserves and the attainment of optimum efficiency with regard to rate, quantity, and cost of production require accurate data concerning the physical properties of petroleum throughout large changes in pressure and temperature. Many schemes have been devised for predicting the behavior of propane, as it is encountered in nature? but the experimental work upon which these predictions are based has not, for the most part, been extended to the higher pressures that occur in practice, nor do these methods permit, as yet, the estima-

Jan 1, 1945

MARSHAL Foch has been made an honorary member of the four national American societies of civil, mining and metallurgical, mechanical, and electrical engineers. The governing bodies of these societies, aggregating 45,000 members, conferred this signal honor in expression of the appreciation of American engineers for the unmatched services of this master of engineering principles. At Engineering Societies Building, in New York City, on Tuesday afternoon, Dec. 13, the presidents of the four societies presented one beautifully engrossed certificate of honorary membership in the four societies. The auditorium was filled so that not even standing room was left, more than a half hour before the cere-monies began, and the main entrance on the street had to be closed. J. Vipond Davies, president of the United Engineering Society, made the opening address. Col. William Barclay-Parsons, 'who was commander of the first engineer regiment to go abroad, addressed Marshal Foch in French. Colonel Parsons said: The art of engineering was defined a long time ago as "the art of directing the great sources of power in nature for the use and convenience of man." No better definition can be found today. Of all the sources of power in nature, the greatest, the most valuable, and at the same time the most difficult to direct, is the energy of man himself. He who can direct human energy and turn it to the service of mankind is a great engineer. You, Marshal, have directed a greater mass of human energy than any other man has ever done. And you have successfully directed this mass for the highest uses of mankind, in that you by its aid have preserved for him one of the most precious of human possessions-liberty-liberty not only for your own illustrious country, but for all the nations of the world. The four national engineering societies, of the United States now desire to make record of their appreciation of this fact and to convey to you an expression of their most profound admiration for the great leader of men by conferring on you honorary member-ship in all the societies, the highest honor in their gift and one hitherto never conferred on a single individual. Four thousand members of these societies were enrolled in the armed service of the United States, the greater part of whom had the glorious distinction to serve the common cause in France under your orders. They heard the voice and they saw the hand of the master as he led them through battle to victory. Now we desire that you will still continue to lead us, but in peace, by permitting us to inscribe your name at the head of our roll of honor, where it will be, as your deeds have been, an example to us to do better work, and where it will remain forever a noble inspiration for all future generations. Marshal, in the name of those members of the societies who served under your orders and particularly .in the name of those who fell on the field of honor in France, I salute you.

Jan 1, 1922

By Ralph Monaghan, Arthur Youmans

General principles of scintillation counter-type instruments for radioactivity logging are discussed and the various possible causes for instability are examined. It is shown how instrumentation problems are solved. Means are discussed for minimizing drift and instability due to "fatigue" of the photomultiplier tube and neutron activation of the crystals. INTRODUCTION Neutron and gamma-ray logs made with logging instruments employing scintillation counters are now routinely available from most of the logging service companies. The superior characteristics of scintillation counters by comparison with older types of detectors promises to bring about important improvements in quantitative interpretation of radioactivity logs. Moreover, new types of logs can be made with scintillation counters which are not possible with other detectors. But in spite of the obvious superiority of these counters with respect to efficiency, speed, and versatility, they suffer from a number of inherent difficulties and weak- nesses. Unless these inherent diffi-culties are fully recognized and satisfactorily overcome by sound engineering of the associated instrumentation, scintillation counter logs are particularly likely to exhibit drift and instability of sensitivity. This defect in logs when they are intended for quantitative interpretation is intolerable and more than outweighs any advantages over the older type of instrumentation when the latter is operating correctly. SCINTILLATION COUNTER OPERATION In general all radioactivity logging instruments consist of a detector sensitive to gamma radiation or to neutron radiation coming from the strata. This radioactivity is either due to naturally decaying radioactive elements in the rock, radioactivity induced in the rock by a neutron source in the instrument, or scattering by the rock of neutrons or gamma rays coming from a source in the instrument. In the scintillation counter the gamma radiation or neutron radiation reacts with the scintillation phosphor to produce light pulses. These light pulses are then converted to amplified electrical pulses by the multiplier phototube. Basically the problem of making a good scintillation counter logging instrument is to make the radiation sensitivity of the system as nearly constant as possible. The size of each scintillation counter pulse is dependent on the energy of the individual quantum of radiation being detected. In normal radiation logging, gamma rays of all energies, up to some maximum value, reach the detector. If a suitable scintillator is used, such as a sodium iodide crystal, each gamma ray produces a number of photons proportional to the energy absorbed by the crystal from the impinging radiation. The light flashes are detected by means of a photo-multiplier tube which contains not only a photo-sensitive cathode from which photoelectrons are collected, but also an amplifier, called an electron multiplier, built inside the photomultiplier tube; the electron multiplier usually has about 10 stages, having an over-all gain of perhaps 500,000. In an ordinary gamma-ray log one wishes to detect all gamma rays down to the lowest possible energy; therefore, one wishes only to reject the "noise" pulses which are invariably present due to thermal emission of electrons from the photo-cathode of the photomultiplier. In other radioactivity logs it may be desired to measure the radiation within a particular energy band, or above

Jan 1, 1958

By H. Foster Bain

THIS subject is one that has attracted my attention for a good many years. All of us have had occa-sion to think of the waste that comes from the poor organization of our methods of finding mines and of looking after prospects. Probably all of us, in, examination work, have made a long and difficult journey to see some prospect, in a far country, or often in the mountains, have found the prospect one that never could be developed, and have learned for the first time that it had been previously examined by from two to six of our professional associates, who, each in turn, condemned the property as worthless. I know properties, as all of you do, that have been repeatedly examined by first-class engineers. Perhaps it would not be safe or wise to have an invariable rule that, each prospect should be entitled to only one examination by one engineer; and yet, it seems to me that somewhere there is a middle ground to take; it is hardly necessary that each little prospect should be examined so many times that the walls get greasy from the climbing of mining engineers, or the stopes get filled up with cigarette stumps. 'This mining engineering profession ought to have brains enough to find some way of making this unnecessary, and of making the benefit of an examination, in some cases at least, and in a much larger number of cases than at present, avail-able to the industry as a whole. If we would save the amount of money that is spent unnecessarily on reexamination of properties, and let that money flow into the actual development of )properties, I believe that, in the long run, we would be better off. Just how to do that is another problem. In 1916, while in London, Edgar Rickard and I attempted to do something of that kind. We started to organize a plan whereby mining engineers might, with the consent of their class, turn over to a central organization their reports on properties they had examined, whereby men who had occasion to look up these same properties might, on payment of a fee (which should go back to the original client, if you desire, or might be devoted to some other purpose for the benefit of the industry), have access to these earlier reports. We found, in the short time we considered this matter, that a good many British engineers, and a good many of the companies, were willing to consider this. In other words, they were willing to pool their information, as a matter of practical experience. We all know the enormous value of pooling information. I think it is a problem that may well be considered from the point of view of the industry as a whole, which the Society might attempt' to work out on a businesslike basis. Assuming, however, that it is possible to work out a plan whereby we get the minimum number of examina-tions that are necessary and we make some saving in money, we reach another stage-the problem of the examination itself.

Jan 3, 1922

By AIME AIME

UNQUESTIONABLY the Coal Division has never had a meeting in which so many outstanding technical papers were presented of immediate practical application to problems of personnel, mining, safety, preparation, combustion, and carbonization. Should there have been those present with the lingering idea that all that was needed for success in the coal industry was a strong back and a weak mind they must have had a rude awakening.

Jan 1, 1942

By R. F. Mehl, C. E. Birchenall

R. E. Hoffman and D. Turnbull—The authors have presented evidence which they have interpreted as indicating that the rate of self diffusion is not intrinsically more rapid at grain boundaries than within the grain. Grain-size effects which apparently exist are attributed rather to impurities concentrated at the grain boundaries. In view of our own experiments and the existing evidence, we believe that the support for this hypothesis is not convincing. We have in progress an investigation in which the rate of self diffusion of silver is being measured over an extended temperature range in both single-crystal and polycrystalline specimens. The results of the single-crystal experiments and some preliminary data on fine-grained polycrystalline specimens have already been reported:' and it is anticipated that a complete report will be published in the near future. The self-diffusion coefficient of large-grained polycrystalline silver (1 grain per sq mm) has previously been measured by Johnson" between 730" and 940°C. The diffusion coefficients which we have measured in single crystals (210 plane normal to diffusion direction) agree within experimental error with values calculated from an extrapolation of Johnson's curve down to temperatures as low as 500 °C. However, it has been demonstrated that the overall self-diffusion rate in fine-grained polycrystalline specimens (initial grain size of 0.003 cm) becomes measurably larger than the overall rate in a single crystal at a temperature of 600°C, and the discrepancy between the two rates becomes greater as the temperature is further decreased. In fact, it has been possible to obtain satisfactory penetration curves for polycrystalline specimens using the sectioning technique at temperatures as low as 400°C. At this temperature, the penetration is 50 to 100 times greater in the polycrystalline specimens than in a single crystal. Fisher" has developed an analysis whereby the ratio of the rate of the unit diffusion process at the grain boundary to the corresponding rate within the grain can be calculated from the penetration curves and an assumption as to the width of a grain boundary. This analysis applied to our data indicates that the unit process at the grain boundary is faster by a factor of 10' at 475°C when the grain boundary width is taken to be 5. The silver used in most of these experiments was obtained from the Handy and Harmon Co. and listed as 99.97 pct pure. Preliminary experiments on 99.999 pct silver from the Jarrel-Asch Co. indicate a grain-size effect of the same order of magnitude as in the less pure silver. Nominally, these purities are as good, at least, as that of the carbonyl iron used by the authors, but of course if an impurity effect does exist its magnitude might be very dependent upon the nature of both major and minor constituents. The authors have cited the work of other investigators who have found no grain-size effects. Neither Steigman, Shockley and Nix" nor Maier and Nelson8 were able to correlate self-diffusion coefficients of copper with grain size. However, all their measurements were performed at or above 750°C; and on the basis of our work with silver, no grain-size effect would be expected at temperatures above about 0.7 of the absolute melting temperature unless the grain size were exceedingly small. Likewise, in the investigation of the self diffusion of lead by Seith and Keil,14 the lowest temperature at which the diffusion coefficient was measured in polycrystalline specimens was 207°C, which is still sufficiently high so that the lack of a grain-size effect is not surprising. Finally, in those experiments on iron from which they concluded that there was no grain size effect, Drs. Birchenall and Mehl seem to have no information as to the actual grain sizes immediately prior to and following the diffusion anneal. Without this information, we believe that their own experiments offer little support for their hypothesis. F. S. Buffington, I. D. Bakalar, and M. Cohen—The results given in this paper agree in order of magnitude with those tentatively reported by us.27 However, significant differences exist in the two sets of data, and it may be well to make an explicit comparison. The diffusion studies at M.I.T. were conducted on somewhat higher purity iron (99.98 pct Fe) than the grades used by the authors, but this is undoubtedly not the answer. Fig. 4 shows the diffusion results of both laboratories for the gamma phase, omitting the authors' data on the commercial steels, while fig. 5 presents a similar comparison for the alpha phase. The divergence is much more marked in the latter case than in the former. In connection with the M.I.T. determinations, all of the runs in the gamma range and those above 800 °C in the alpha range were conducted with specimens having a relatively thick (0.002 cm) electrodeposit of radioactive iron. This practice minimizes any possible error due to extraneous diffusion that may occur during the heating to and cooling from the operating temperature. An exact solution of Fick's law for these boundary conditions was used in calculating the diffusion coefficients. At a later time, three runs were made below 800°C, using very thin electrodeposits similar to those of the authors, and the points fell considerably below the values expected from the extrapolation of the results based on the specimens with the thick deposits (compare dash-dot line in fig. 5). However, in the runs with the thin deposits, deviations of 100 pct were found between the individual specimens, whereas the maximum deviation with the thick deposits was less than 25 pct. Accordingly, it is not known at the moment whether the M.I.T. points below 800 °C should be given as much weight as those above 800°C. If this were done, the frequency factor would be of the order of 400 cm2 per sec, which is quite high. In other metals, the frequency factor for self diffusion lies between about 0.1 and 10 cm2 per sec. As the points below

Jan 1, 1951

By J. V. Gluck, Ping-Wang Chiang

The tellurium-rich region of the Sb-TI-Te ternary system was investigated by means of DTA, metallo-graphic, X-ray, and electron beam microprobe techniques on the sections Sb2Te3-T12Te3, SbTlTe2-Te, SbT1Te2-Sb2Te3, and SbTlTe2-T12Te3. The phase behavior of this region is summarized in terms of four ternary invariant reactions and a schematic reaction diagram is suggested. Isopleths for the sections SbT1Te2-Sb2Te3, Sb2Te,-T12Te3, and SbTlTe2-Te were constructed, and a schematic diagram of the projections of the liquidus lines and invariant planes is presented. No evidence was found to support the existence of the ternary compound "SbTlTe3", or pseudo-binary behavior of the section T12Te3-Sb2Te3, as reported by Borisova and Efremova. Electrical conductivity, Seebeck coefficient, and thermal conductivity measurements were made at room temperature on fully annealed samples. 1 HE phase relationships in chalcogenides are often complex and difficult to resolve, particularly since the approach to equilibrium is a rather slow process. For example, the phase diagram of the T1-Te binary system was in doubt until clarified by Rabenau et al.,1 the phase fields at compositions near Bi2Te3 in the Bi-Te binary system have only recently been satisfactorily elucidated by Glatz,2 and there may still be some question as to the extent of the Sb2Te3 field in the Sb-Te system.3-5 In ternary systems, the existence of the compound "AgFeTe2" was the subject of a number of conflicting reports6-8 and the stoichiometry of the composition "AgSbTe2" was in doubt for a period of time.9 Recently, questions have arisen regarding the existence of certain compounds in the ternary systems Bi-Tl-Te10-14 and Sb-Tl-Te.15 The impetus for studies of these latter systems stemmed from the report of Borisova et a1.10 of a congruently melting ternary compound, "BiTlTe3", which apparently had extremely favorable thermoelectric properties for room-temperature cooling applications. Attempts by other investigators to produce the compound or confirm the transport properties proved to be unsuccessful.12-14 Recently, Chiang and Gluck14 reported studies of the phase relations in the tellurium-rich region of the Bi-T1-Te system which indicated that the section T12Te3-Bi2Te3 was not pseudobinary as suggested by Borisova et a1.10 The contention of Spitzer and sykes12 was supported that the composition "BiT1Te3" was multiphase, with the primary constituent actually being BiTlTe2, a compound whose existence has been well demonstrated.16,17 The investigation reported in the present paper was prompted by a later report of Borisova and Efremova15 on a similar study of the section T12Te3-Sb2Te3 from the Sb-T1-Te system. They also claimed this section to be pseudobinary, and that a ternary compound "SbTlTe," was formed peritectically. Some "preliminary" crystallographic data were given for the compound and thermoelectric transport properties were presented. In view of the questions concerning the behavior of the Bi-T1-Te system and the existence of the compound "BiT1Te3" it was suspected that the Sb-T1-Te system might behave in a similar fashion, particularly in light of the known existence of a compound SbT1Te2, iso-structural with BiT1Te2.17 Consequently, an investigation was undertaken to clarify the phase relationships in the tellurium-rich region of the Sb-T1-Te system. It is the purpose of this paper to present the results of this study, including a representation of the phase relations, isopleths for various composition sections, and the determination of some phase compositions and transport properties. EXPERIMENTAL PROCEDURES Commercially available high-purity (99.999+ pct) elements, purchased from the American Smelting and Refining Co., were used for the sample preparation. All samples were made from thoroughly mixed powders of previously prepared master alloys: SbTlTe2, Te, Sb2Te3, and T12Te3. Stoichiometric quantities of the constituents for each 10-g sample were weighed into a specially cleaned fused silica tube and sealed under a vacuum of better than 5 x 10-5 torr. The sealed constituents were fused and reacted at 650° to 750°C for at least 4 hr under continuous agitation in a "rocking" furnace, and the resulting product was air-cooled. The tube was opened and the sample was ground to a powder. A portion of the powder was rebottled in a DTA tube under vacuum, and the rest of the material was similarly resealed in a separate tube, re-fused in the rocking furnace, and again cooled to make the ingots for electrical and microstructural studies. All samples were subjected to further heat treatments as discussed in the section on experimental results. Each DTA tube was made of 7-mm-OD fused silica tubing with a concentric 2-mm-ID depression about 4 mm long formed in the bottom to accommodate a thermocouple. The size of a DTA sample was 0.5 to 1.0 g. An Aminco Thermoanalyzer whose accuracy was within 2°C18 was used for the DTA measurements. The metallographic samples were prepared by conventional techniques. A solution of FeCL dissolved in a methanol-HC1 mixture was found to be the most satisfactory etchant. Electron beam microprobe scanning and point-count examinations were made on polished and unetched samples using an ARL Electron Microprobe at an electron beam voltage of 20 kv. The detectors were set to receive characteristic La1 radiation. Calibration standards of the pure elements were incorporated in each sample mount; quantitative point counts were calibrated by a method similar to Ziebold

Jan 1, 1969

By Ta M. Li

This article draws freely on the experiences of the engineering and operating staff of P.T. Inco and its parent firm Inco Ltd. In addition, information was derived from papers presented during the recent International Laterite Symposium, held in conjunction with the 1979 AIME Annual Meeting, New Orleans, La., February 19-21. The author wishes to acknowledge all contributors and, in particular, Roy Aitken, president and managing director, P. T. Inco.

Jan 7, 1979

By Henry M. Howe

.... So, beyond and above the immediate and tangible ends of membership, ever-present and evident, selfish and generous alike; beyond and yet at the root of that genuine affection for our association which is so strong in many of us, there lies earnest sympathy with the ultimate and essential purpose of its being—that to which as a nucleus all other purposes are but contributory—which is, to

Jan 1, 1895

By Ballard H. Clemmons

THE future of the steelmaking industry of the Birmingham, Ala., district is closely related to and, in a large measure, dependent on the development of workable, economic processes of ore concentration. Operations thus far in the area have been possible only because of the fortuitous occurrence of iron ore, fluxing stone, and coking coal-all the primary iron-making materials within a 25-mile radius of the blast furnaces.

Jan 12, 1950

By Arvid Holst Mortensen

The rational exploitation of deposits for cement manufacture requires evaluation of the material, the planning of the quarrying and the right choice of quarry machinery. By using a computer for all evaluations and planning work the optimal recovery of material is arrived at and a quarry layout - and machinery is decided upon. The result will be uniform production throughout the lift of the deposits using a rationally chosen quarry equipment.

Jan 1, 1977

By Cushwa, C. C.

AT the Park Utah Mine, labor costs of stoping A have been reduced from 30 to 40 per cent. by the use of double-drum hoists and scrapers. The application of scrapers varies with the methods of timbering. In stopes, which must be timbered with square-sets or stringer sets, one method is used; another is used in wide orebodies that can be held open until filling is introduced; and still another in narrow flat veins. Nearly all the oreshoots at the Park Utah lie at less than 50" from the horizontal, and most of the ore is difficult to handle through flat chutes. Proper care is probably the most important requisite for successful scraping, as serviceable equipment can be obtained from several manufacturers. One capable mechanic, therefore, was put in charge of the scraper hoists. He visits every stope daily, oiling hoists and tail1 blocks, inspects all equipment, splices cables and changes "set-ups" when necessary; his pay has been a good investment. The Park Utah now has in use ten double-drum Turbinair hoists, and one Sullivan double-drum a. c. hoist of the same capacity and outside design as the air hoists. The electric hoist is slower than the air hoists and does not pass large boulders easily; it is, however, a very effective machine. The air hoists are fast, powerful and

Jan 1, 1925

By D. Hnrrington

THE Dust Symposium was attended by approximately 100 persons, nearly all of whom remained from the starting hour (2 p. m.) until the use of the auditorium was demanded for another meeting at 5:30 p. in. In calling the meeting to order, D. Harrington made a few remarks as to the importance of the health dust problem in mining as well as in general industry and expressed gratification that the subject is now out in the open and that mining people are desirous of ascertaining the facts. B. F. Tillson acted as chairman of the meeting. The milling executive who desires to know what to do to prevent his workers from being unduly exposed to the dust hazard can get much out of the paper by D. E. Cummings, who has been doing much work in mines trying to keep -the dust in the air within safe limits. His recommendations indicate that the main protection of the worker in mines is by adequate ventilation, supplemented by the extensive use of water in drilling, as well as in water curtaining to condition air both in regard to dust content and to temperatures. Blasting was shown to be one of the chief causes for dust and it was recommended that whenever feasible all blasting should be delayed to the end of the working shift.

Jan 1, 1935