Search Documents

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By R. S. Dean

IN THE COURSE of its investigations directed toward providing strategic metals from domestic sources and toward utilizing power from Federal power projects in West, the Bureau of Mines concluded some years ago that the development of a method for producing electrolytic manganese might well be an important step towards both goals. Accordingly, laboratory investigations were undertaken in 1935. Further studied on a relatively large laboratory scale indicated that electrolytic manganese could be made from domestic ores at a cost not out of line with other nonferrous metals. On the basis of these results, the Electro Manganese Corp. Operating under U.S. Patent 2,119,560 issued to S, M, Shelton and assigned to the Secretary of the Interior for administration, undertook commercial production of electrolytic manganese at Knoxville, Tenn, This company has brought the process through the pilot-plant stage successfully, and is now regularly producing approximately one ton a day.

Jan 1, 1941

By CHARLES R. KETES

I. INTRODUCTORY. INDUSTRIALLY, the most important service that geological science can now render to mining in the Upper Mississippi leadand zinc-fields is to devise some practical scheme whereby the productive ore-belts may be located with greater certainty than they have been in the past. Up to the present time there has been little service of this kind, and in spite of all that has been worked out concerning the geologic features of the region, and notwithstanding all that has been written about these ore-deposits, this particular phase of the subject has been, for some reason or other, the very one that has received the least consideration. The neglect by geologists in this respect has been all but complete. The following notes are suggestive of some practical solutions to the problems presented. As here suggested, the geologic relationships of the ore-bodies were surmised some years ago, though somewhat vaguely perhaps. No opportunity for securing critical data appeared until recent investigations of a private character were undertaken, which bad in view the extensive prospecting of undeveloped areas. Fresh from rather wide experiences of a decade in the principal mining-regions of four continents, and after a lenstrum's residence among the chief mining-camps of the West and of Mexico, under conditions which measured geologic hypotheses in meters and rigidly tested their values in, terms of dollars, the recent return to the Joplin field and a new survey of its ore-conditions were fraught with somewhat unexpected results. Aspects of the ore-deposition were presented of which previously there was no hint. Ten years' absence from the district had tended greatly to clarify former hazy impressions. It enabled many features, then only dimly outlined, to be considered more nearly in their true perspective and in their real relationships to their surroundings. It permitted a great mass of details collected a dozen years before in connection with the work of the Missouri Geological Survey to be viewed under new light and to

Feb 1, 1909

By H. E. Cline

Solidification of Pb-Sn alloys ranging in composition from 1.2 to 56 at. pct Pb ws observed with polarized light. Lamellar structures were observed over a larger range of compositions in alloys containing excess tin than excess lead, as expected from constitutional supercooling. The occurrence of pools of supercooled liquid surrounded by lead is explained by the difficulty in nucleating tin. Cells and dendrites weve observed in tin-rich alloys. Evidence was found that the degenerate structure formed at low growth rates, the formation of faults, and abrupt changes in composition and structure can be attributed to non-steady-state growth. The apparent interface shape was observed to have deep grooves at the interphase boundaries. HUNT and Jackson have observed the shape of the interface during growth of organic eutectics. They observed the formation of lamellar faults and shape instabilities upon changes in growth rate. The lamellar structure in these organic eutectics was not restricted to the eutectic composition. Recent work by Mollard and Flemings2 indicated that Pb-Sn alloys from 12 to 26 at. pct Pb could be solidified with a lamellar or rodlike structure if a sufficiently steep temperature gradient was used at a slow growth rate. Observations of the solid liquid interface of the Pb-Sn eutectic were made by Davies3 using polarized light. Photographs were at too low a magnification to determine the interface shape, but he has concluded that tin was the leading phase. In the following experiments, solidification of a range of Pb-Sn alloys from 1.2 to 56 at. pct Pb was observed using polarized light, to determine the factors controlling stability of the lamellar structure. EXPERIMENTAL Procedure. One hundred-gram ingots of alloys prepared from 99.999 pct pure Pb and Sn were cast into graphite molds under argon. The compositions of the alloys were 1.2, 6, 12, 26, 36, 46, and 56 at. pct Pb. Two-gram pieces were melted between two cover glass slides which were squeezed into a 1-mm separation. Samples were then observed under polarized light in a hot stage shown in Fig. 1. A long working distance objective designed for viewing at 500 times was used. Photography was made difficult by the lack of illumination and contrast at these high magnifications. By using an elliptical polarization compensator, as suggested by A. Holik, the contrast and illumination could be optimized. Photographs could be taken only at slow growth rates to avoid excessive interface motion during the 15-sec exposure used. The solidification rate was varied by increasing or decreasing the power to the heater. It was found that insulation was necessary to avoid undesired growth rate fluctuations. The temperature gradient, as measured with two thermocouples 1 cm apart, was 80" ± 20°C per cm during all the experiments reported here. The advantage of this procedure is in being able to observe solidification while it is occurring. However, the observations are restricted to the glass-metal surface and may be influenced by this surface. Also, one has no knowledge of the interior of the sample, in contrast to studies of the freezing of transparent organic eutectics.' Observations. The alloy near the eutectic composition (26 at. pct Pb) solidified in a lamellar structure when the growth rate was uniform. If the growth

Jan 1, 1968

Jan 1, 1961

By Raymond M. Howe

Additional data have been secured on the disintegration of furnace linings and the spalling of stove brick. The first article on the disintegration of furnace linings appears to have been written by John Pattinson in 1876.l The furnace involved was 85 ft. (25.0 m.) higher and 27 ft. (8.2 m.) in diameter at the boshes; after being in blast five years, the top brick became contaminated with carbon and disintegrated. An examination of the lining showed that the discolored, disintegrated brick were in a zone found from 35 to 67 ft. (10.6 to 20.4 m.) above the hearth; immediately below, in a zone extending from 22 to 40 ft. (6.7 to 12.1 m.) above the hearth, the brick were hard and porcelain-like in appearance. Analyses of samples taken from the different sections are given in Table I. The water-soluble portion found in the sample taken 39 ft. (11.8 m.) above the hearth had a composition approximately as follows: silica, 0.50 per cent.; lime, 0.04 per cent.; potash, 0.78 per cent.; soda, 0.20 per cent.; potassium chloride, 6.19 per cent.; moisture, 1.03 per cent.; total, 8.74 per cent. The carbon Table 1.—-Analyses of Samples Taken from Diferent Sections of Furnace . I ii In Iv v Section 67 Section 45 Seotion 39 Section of Original ft Above ft above ft above vitrified Lining Hearth Hearth Hearth Portion Per Cent. per Cent per Cent per cent. per Cent Silica........................... 55.70 55.60 55.67 47.60 37.07, Alumina........................ 35.50 35.40 30.00 26.47 23.18 Ferric oxide..................... 3.00 1.32 0.96 Lime........................... 0.23 0.06 0.17 Magnesia....................... 1.22 0.95 0.86 0.00 Potash......................... 2.60 2.10 5.30 7.54 21.59 Soda.........,.................. 0.45 0.42 1.67 0-76 6.28 Ca1bon ......................... 2.05 3.24 5.97 Carbon dioxide.................................. 2.. 17 Water...................................... 7.70 Water-soluble........................... 8.74

Jan 1, 1920

Jan 1, 1965

By G. R. Speich

The age-hardening of Fe-18 to 21 pct Ni marten-sites containing small amounts of titanium, aluminum, copper, or molybdenum has been studied by hardness measurements, transmission electron microscopy, extraction replicas, and X-ray and electron diffraction. Electyon-probe microanaly-sis of the extracted precipitates was also performed. The effects of temperature and composition on the aging kinetics have been studied in detail for Fe-20 pctNi-Ti martensites. All the martensites hardened on aging at 400" to 500 "C with a single aging peak. In the Fe-20 pct Ni-Ti martensites hardening was associated with the formation of a fine dispersion of NisTi. No precipitation was observed in an Fe-21 pct Ni-2.6 pct A1 alloy, although the hardness increased from 327 to 545 Dph during aging at 500°C. Copper was precgitated from an Fe-20 pct Ni-10.7pct Cu alloy, at least during the later stages of age-hardening. Hardening in an Fe-18 pctNi-5pct Mo alloy was associated with the precipitation of an intemzetallic compound tentatively identified as NisMo. The formation of austenite and the recovery of the defect structure of the martensite occur simultaneously with the normal precipitation processes &ring aging of these alloys. THE age-hardening of substitutional iron-base martensites is an important subject for study since age-hardening is one of the principal means of strengthening the substitutional iron-base martensites in precipitation-hardening stainless steels1 and maraging steels.a~4 In contrast to Fe-C martensites, these martensites are relatively soft and ductile in the as-quenched condition, due to the low solid-solution hardening effect of the substitutional elements as compared to carbon. Also, these martensites are hardened by aging at low temperatures in contrast to Fe-C martensites which generally soften on tempering. Titanium and aluminum, singly or in combination, as well as copper and molybdenum, have been the principal alloying additions to stainless steels to obtain an age-hardening reaction.' Ti-A1 or Co-Mo-Ti combinations have been used in the case of maraging steels.3"4 The present work has been confined to a study of the age-hardening characteristics of an Fe-18 to 21 pct Ni martensite to which small amounts of titanium, aluminum, copper, and molybdenum were added in order to study the effects of each alloying element separately. The age-hardening characteristics of these alloys were studied by hardness measurements, transmission electron microscopy, extraction replicas, and X-ray and electron diffraction. Electron-probe micro-analysis of the extracted precipitates was also performed. The types and dispersion of precipitates, the formation of austenite, and the recovery of the defect structure of the martensite all were studied. EXPERIMENTAL PROCEDURE Alloys. The compositions of the alloys studied are listed in Table I. The level of 18 to 21 pct Ni was chosen to assure complete transformation to martensite on quenching and is the same nickel level used in maraging steels. The concentrations of titanium, aluminum, copper, and molybdenum were chosen after a study of the and Fe-Ni-MO' ternary diagrams indicated how much of each alloying element could be dissolved in austenite. Alloys with 2 and 4 pct Cu were also studied, but these did not show precipitation hardening at the nickel levels studied and will not be discussed further. The alloys were prepared from electrolytic iron and high-purity* nickel, titanium, aluminum, copper, and molybdenum by vacuum melting of 20-lb heats. These were vacuum-cast into two 8-lb ingots. The ingots were hot-rolled at 1100°C to 1/2-in. plate and subsequently cut into 3/8-in. cubes. The cubes were sealed in evacuated quartz capsules and solution-treated for 16 hr at 1100°C, except for the Fe-20 pct Ni-10.7 pct Cu alloy and Fe-21 pct Ni-2.6 pct A1 alloys which were solution-treated for 16 hr at 1300" and at 1250"C, respectively. Metallographic examina-

Jan 1, 1963

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, aged 36. Experienced copper metallurgist and mining geologist. Familiar also, through 15 years' broad practical experience, with mining, cyanidation, concentration (including oil flotation), metallurgical accounting, and mine and plant management. Best references. No. 237. Member, graduate engineer with 10 years' experience in malleable, gray -Iron, and steel, as chemist., metallographist, and metallurgist. Researches and investigations by laboratory methods and under works conditions. No objection to some routine. No. 243. Member, technical graduate, broad experience in coal, oil, and clay. Will go anywhere as mining geologist after Sept. 1, 1915. No. 244. Member, technical graduate, aged 30, married, with over 10 years' experience as chemist, engineer on construction, superintendent and general superintendent of bituminous coal and coke plants. SpeaksSpanish. References. No. 245. Member, open for engagement as mine safety inspector or as superintendent of bituminous coal mine. No. 246. Member, graduate mining engineer, with five years' experience in coal mining as mining engineer, construction engineer, pit boss, and superintendent, open for engagement. Best references. No. 247.

Jan 9, 1915

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of April, 1913: BARNES, BLAKESLEE, Min. Engr Burrwood, La. BOYLSTON, HERBERT M., Cons. Met. Engr 26 Abbot Bldg., Cambridge, Mass. BUEHLER, HENRY A., State Geol Rolla, Mo. CASTO, WILLIAM H., JR., Mining Bonanza, Idaho. COHEN, MAXWELL B., Mill Operator Miami, Ariz. EVANS, MILTON R., Shop Draftsman 92 Division St., Kingston, Pa. HARPER, WALTER S., Asst. Treas 42 Broadway, New York, N. Y. JAMES. JAMES S.. Min. Engr Telluride. Colo.

Jan 5, 1913

By W. H. C. SIMMONDS

The mining, metallurgical, and petroleum industries can be viewed as financial or as social institutions or both. The differences between these two conceptions of their businesses will influence their environmental 'and social actions. During the next 10-20 years western industry will be subject to a drop in the growth of a more highly educated labour force and to the emergence of holistic economics, new national goals, and a new ecological perspective. The profitability of the mining industry may therefore be influenced by the human side of its business to a greater degree. The increasing human, social, and environmental responsibilities can be discharged by improving the miner's equipment; by learning to look at situations through the eyes of all those involved; by developing common 'languages' which governments and the public can understand; and by mediating where feasible on the international scene.

Jan 1, 1978

Jan 1, 1966

Jan 1, 1970

By John S. Alexander

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935