Search Documents

By R. A. Burmeister, P. E. Greene

Two methods for the synthesis and growth of single crystals of B6 P are described: a solution-growth process employing nickel as the solvent, and a vapor-growth process employing BBr3 and pH3 as the reac-tants. Relevant portions of the Ni-B-P phase diagram have been examined and liquidus data are presented for an isobaric section at an equivalent P2 pressure of 3.8 Torr, and an isothertnal section at 1300°C. Solution-growth techniques are described and the purity and crystalline perfection of the resulting material is discussed. Epitaxial growth of BeP on &P substrates has been obtained using the vapor-phase system. Evidence is presented which supports the assignment of the stoichioknetry B6P to boron sub-plwsphide. THE B-P system differs from other III-V systems in that it contains two distinct compounds. The existence of the monophosphide (BP) has been known for some time,' whereas the subphosphide (B6P) was reported only recently.' Both of these compounds are large bandgap semiconductors (Eg = 2.0 ev for BP~ and 3.3 ev for B6P4), and are therefore of interest for optoelectronic applications. The crystal structure of B6P is quite different from those of most semiconductors, being derived from that of a-rhombohedral boron by the incorporation of the two phosphorus atoms in the intericosahedral sites of the a-boron unit cell?76 B6P also exhibits a number of unusual characteristics, including a high degree of chemical inertness, hardness, and high-temperature stability. No information concerning other physical properties is available in the literature. The present study is part of a broader investigation of the preparation and properties of B6P. This paper considers methods of growing single crystals of B6P of suitable size and quality for physical-property measurements. A detailed discussion of the electrical and optical properties of B6P will be given elsewhere.' GENERAL CONSIDERATIONS The method first used to synthesize B6P was the disproportionation of BP' according to the reaction The equilibrium P2 pressures corresponding to this reaction were also determined .'" It is therefore possible, in principle, to apply several of the reactions reported for the synthesis of BP to the synthesis of B6P merely by selecting lower phosphorus pressures or higher temperatures, in accordance with the equilibrium data. Other techniques for the direct synthesis of microcry stalline B8P have also been reported.1°

Jan 1, 1968

By D. J. McAdam, R. W. Mebs

THE technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture, According to the prevalent view,8 the technical cohesive strength of a metal, in any particular state as regards prior mechanical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress.? In two previous papers by one of the authors,14,15 evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.8 In this paper, as in the previous papers,14,15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress." 14,15 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,"' however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average of the three principal stresses.* This influence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers, 14,15 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant conclusions are derived from experimental data obtained by other investigators. They are based chiefly on results of tension tests

Jan 1, 1943

By Michael B. Bever, Carl F. Floe

he possibility that carbon may be soluble in copper to a limited extent has bten recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are freauerltlv used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. Review of Literature In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of 0.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.9258 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been ill prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as 0.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1946

By Carl F. Floe, Michael B. Bever

he possibility that carbon may be soluble in copper to a limited extent has bten recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are freauerltlv used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. Review of Literature In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of 0.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.9258 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been ill prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as 0.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1946

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Walter Knox, J. D. Doherty

IN 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. SUMMARY OF RESULTS Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3). 2. The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 1 1.6 per cent to 19.2 per cent. There was a noticeable segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may he a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance I. The removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. With intermittent operation the burning rate was almost always less than the feeding rate. The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. I3). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). GUIDING PRINCIPLES In planning the investigations, the following principles were adopted: Selection of Healing Equipment.-Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By H. E. Dunn, C. M. Cosman, J. H. Brennan

Up to the beginning of World War I, the American ferro-alloy industry was in its infancy and largely dependent on Europe. During that War, capacity was over expanded. Later recovery and commercial and scientific development have resulted in an industry which in 1957 produced 1.8 million tons of ferro-alloys. THE ferro-alloy industry is today an important element of the industrial structure of the United States. Its output is valued at almost half a billion dollars annually and its products are basic not only to National defense but also to the peacetime standard of living. This has not always been so. The ferro-alloy industry from late in the last century has grown from small beginnings, nurtured by the demand for stronger, tougher materials; by the search for steels capable of absorbing severe impact loads and resisting corrosive media and high temperatures; and also by the need for electrical and electronic specialties. Conversely, the ferro-alloy industry has grown because it developed improved steels and alloys by extensive research, and because it was able to show to steel makers the advantages accruing from the more extensive and the more economical use of alloying elements. The industry has grown in scope from producing a few grades of ferro-alloys of the more common metals-manganese, chromium, vanadium, silicon, titanium, tungsten, and molybdenum-until there are today some 150 compositions of ferro-alloys available to the steel maker, including such elements as columbium, zirconium, and boron. In 1912 the industry produced 360,000 tons of alloys valued at about $12,000,000, while 1957 production figures show an output of 1.8 million tons worth $440,000,000. In the United States, the history of an industry is largely the history of the companies making up this industry; hence, this paper will briefly trace the development of the most important ferro-alloy-producing companies. Quite varied have been the reasons that caused the different companies to move into the ferro-alloy field; the Willson Aluminum Co., seeking methods of producing aluminum, succeeded with the production of calcium carbide, and their developing electric furnace skills led them to the production of ferro-silicon and ferrochromium alloys. Willson was the predecessor of the Electro Metallurgical Co. of Union Carbide. Two Pittsburgh undertakers, interested in vanadium as an alloying agent for steel, set about to find a mine and, ranging as far as Peru, fathered American Vanadium Co., the predecessor of Vanadium Corp. of America Experiments of the

Jan 1, 1961

By Eizo Yabuuchi, Yukito Imanaga

INTRODUCTION In treatment of mine drainage, it is well known that the neutralization by calcium carbonate is far better than by slaked lime because of cheaper cost and better precipitability of its deposit. However, in case of iron ion contained in the mine drainage consists of ferrous salt, the ferrous salt must be oxidized to ferric salt before neutralization, because the ferrous salt does not react with calcium carbonate. At Yanahara Mine, during the period of 1950 through 1956, ferrous ion in the mine drainage had been oxidized to ferric ion, simultaneously neutralized by adding calcium carbonate into the aerated drainage. During the period of 1961 through 1974, after passing through many kinds of treating methods, the neutralization had been carried out by addition of calcium carbonate into the drainage after oxidized its ferrous ion to ferric by using nitrous gas as an oxidizing catalyzer. Meanwhile we had made an experiment on the oxidation of ferrous ion by utilizing iron bacteria, and developed a method which oxidized ferrous ion in large quantities briefly by cultivating and concentrating iron-oxidizing bacteria. Since 1974, we have been operating successfully for treating the drainage at Yanahara Mine by means of utilizing these bacteria.

Jan 1, 1976

By D. B. Crouch, D. A. Poulter

The engineering and metallurgical assessment of the McLaughlin Project ore body concluded that an open-pit mine and cyanide leach mill process would be feasible, producing both waste rock and residual mill tailings. As a part of the planning and permitting process, site selection studies were conducted for the tailings and waste rock disposal. The site selection process began with a regional identification of potential disposal sites and proceeded through 1) regional screening, 2) elimination of sites with obvious fatal flaws, 3) qualitative ranking of site evaluation criteria, 4) quantitative ranking of sites, 5) field investigation, 6) evaluations of field data, and 7) selection of preferred sites. Based on this approach of site rankings and field evaluations, tailings and waste rock disposal sites were selected and recommended for the preliminary design phase of the permitting and project development process. The site selection study provided the documentation necessary to justify the use of these sites for waste disposal and enabled Homestake Mining Co. to anticipate and integrate environmental concerns with agency requirements into the planning process.

Jan 1, 1986

By H. S. Cannon, F. N. Rhines

IT. H. Hausner( Sylvunia Electric Products Inc., Bay-side, N. Y.)—The results reported by the authors are interesting because they contribute some information on the principles of sintering and also because of a certain practical value for the manufacture of powder . metallurgical parts in production. Pressed powder compacts are frequently sintered in a boat in several layers so that the lower layers are actually sintered under the weight of the upper layers and, therefore, are frequently deformed. The authors gave information on this deformation process by determining the effect of the load on the density. The experimental setup of the authors, however, has a disadvantage—that the sintering occurred in a cylindrical container so that the deformation was stopped in the direction of the diameter. The authors should have rather called this a study of hot-pressing than of sintering. I want to call the attention of the authors and others interested in sintering under load to the experimental work described by Dawihl and Rix.' These authors sintered cylindrical compacts under a lengthwise ten-sional load of 0 to 25 g and found that the shrinkage in length and diameter changes considerably with the load, but that the volume shrinkage is affected very little by the load. H. S. Cannon (authors' reply)—We wish to thank Dr. Hausner for calling attention to the experimental work of Dawihl and Rix. The fact that they found volume shrinkage little affected by varying tensional loads during sintering seems to support the contention that the forces due to loading are equivalent to and additive to the forces which cause densification. This contention is the basis of our comparison of sintering and creep.

Jan 1, 1952

By Janshi Sen

VERTICAL-INTENSITY magnetometers, such as the Hotchkiss Superdip and the Askania vertical field balance, are now [ ] widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. 1, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, [ ] h, can be calculated from the following relation: [h=a=tan¢=G-F h=aXFy] where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1944

By R. L. Templin, D. A. Paul

The modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 Ib. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately corrcct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements. a National Metals Handbook. b Intcrnatiunal Critical Tables. '' Aluminum Co. of America. " Based on density of alurminum (2.70). c Smithsonian Pliysical Tables.

Jan 1, 1931

By Earl R. Hoskins, James E. Russell

The electrical resistivity of rocks has been studied quite extensively, in particular, the effects of temperature and confining pressure on resistivity. References 1 through 6 at the end of this chapter pertain to electrical resistivity of rock and contain further references on the same topic. The present study is motivated by an interest in determining the in-situ properties of rock as well as the stress state of the rock and how these quantities are changing with time. Most of the previous work on the electrical resistivity of rocks has been directed toward saturated rocks at relatively high confining pressures and temperatures. The present study was oriented towards air-dry surface rock that might occur in mine pillars. The mean stress and temperature under such conditions are comparatively low. It has been demonstrated that the resistivity of rock is highly dependent upon the porosity. In fact, for saturated rocks, a relationship referred to as Archie's law has been established between porosity and electrical resistivity. In the case of saturated rock, the property that is actually being measured is the resistivity of the solid/fluid system. Since the resistivity of the fluid alone is usually much lower than that of the dry rock, it is understandable that the resistivity of a saturated rock is in general several orders of magnitude lower than the resistivity of a relatively dry rocli. For dry rock, it seems reasonable that the electrical resistivity should increase as microcracks open within the material. Since microcracks open as material is stressed closer and closer to its failure point, it appears that there should be a correlation between electrical resistivity

Jan 1, 1970

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry's use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel 'economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry's use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel 'economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By R. J. P. Lyon

It is usually assumed1,2 that ore deposition is relatively slow, taking place over tens of thousands of years. Yet many syntheses and phase changes can be completed in the laboratory in a matter of hours, under essentially the same pressure and temperature conditions to be expected in nature. Much has been written about geothermometry, and Ingerson's recent summary2 an hardly be surpassed. Rather than review the whole field, this article will deal specifically with diffusion rates in solid solutions* of the sulfide minerals. In the study and application of temperature-indicating phenomena to problems of ore genesis, the time factor has often been neglected. In the particular case of sulfide systems, the speed of unmixing and diffusion of the constituent phases in the solid solutions has seldom been considered when laboratory data are applied to the genesis of natural sulfide ores. Chalcopyrite and Bornite Intergrowths: Chal-copyrite and bornite are copper iron sulfides often found in association. In many ores the individual grains appear to have mutual boundaries, but bladed intergrowths are quite common. Early workers in the field, " deduced that while these patterns could have been formed by replacement, they could be experimentally reproduced from the unmixing of solid solutions of the two previously homogenized at 475°C. Much of the ore from Roan Antelope mine in the Rhodesian Copper Belt exhibits these bornite-chalcopyrite intergrowths, from which it has been deduced that the ores could have been subjected to a minimum temperature of 475°C. In several recent interpretations,' this temperature rise has been considered to result from a regional metamorphism of an original syngenetic copper-bearing sediment. The same temperature rise to 475 °C was suggested from similar intergrowths in the sulfide- • The general subject of solid solution in structurally similar minerels is treated in many texts'. :' ' and will not be further elucidated. bearing ore from the Happy Jack uranium mine8 on tile Colorado Plateau, although this temperature had a different origin. In 1931 SchwartzV etermined that 475°C represented the unmixing temperature of his bornite-chalcopyrite solid solutions but, more important, that the characteristic intergrowths of bornite and chalcopyrite could be preserved only if the solid solution were chilled quickly to room temperature. This significant corollary has been almost completely neglected by both Davis and Miller.7,8 By suitably decreasing the cooling rate, Schwartz found that the original pattern of the intergrowth was reformed (Fig. 1). The cooling rate was critical. In cooling from 475°C to room temperature in

Jan 1, 1960

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedel1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 8oo ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By D. C. Hilty, W. Crafts

The solubility of oxygen in iron containing aluminum has been determined at 1550°, 1600°, and 1650°C and found to be much higher than predicted from theoretical considerations, possibly due to equilibria with an iron-aluminum spinel phase rather than pure AI,O.. The presence of manganese greatly increased the deoxidizing power of aluminum. DEOXIDATION and inclusion formation in steel have proved to be elusive phenomena that are difficult to control in spite of much effort to understand and evaluate the reactions. Study of the problem indicated that more accurate data on the solubility of oxygen in iron containing deoxidizers were essential to further progress, and an empirical determination of oxygen solubilities has been initiated at the Union Carbide and Carbon Research Laboratories, Inc. The investigation has included the effects of aluminum, silicon, manganese, and combinations of these elements at 1550°, 1600°, and 1650°C. The equipment and experimental procedure as well as the results of a study of the effects of aluminum are described below. In general, it was found that the solubility of oxygen in iron containing aluminum is much higher than predicted, possibly because of the formation of complex nonmetallic phases, and that manganese greatly increases the deoxidizing power of aluminum. The generally accepted deoxidation curves for 1600°C are summarized in fig. 1, from "Basic Open Hearth Steelmaking"'. These curves are assumed to represent the solubility of oxygen in the presence of deoxidizers and should indicate the limits of mis-cibility gaps in the phase diagrams of the systems that control the formation and character of non-metallic inclusions as described by Benedicks and Lofquist'. They were derived mainly by application of the methods of thermodynamics to the available experimental observations, and by calculations based on the thermal constants of the pure substances when experimental data were lacking. Among the more notable researches contributing to the development of knowledge of oxygen solubilities are those of Korber and Oelsen8, 4, C. H. Herty, Jr. and associates5,6, Krings and Schackmann7, Went-rup and Hieber8 Schenck and Briiggeman9, Vacher and Hamilton'" and Chipman and co-authors 1,11,12,13 Practically, the deoxidation curves are of limited value in predicting oxygen content and rationalizing deoxidation practices. The reasons for this inadequacy appear to be error from inaccurate data, oversimplifying assumptions, interacting effects of combined deoxidizers, and possibly unknown extra-equilibrium and side reactions. Although inclusion formation is a very complex reaction it must be re-

Jan 1, 1951